Extron XPA 1002, XPA 2001-70V, XPA 2001-100V Half-Rack Audio … · 2019. 11. 25. · Extron XPA...
Transcript of Extron XPA 1002, XPA 2001-70V, XPA 2001-100V Half-Rack Audio … · 2019. 11. 25. · Extron XPA...
-
Extron XPA 1002, XPA 2001-70V, XPA 2001-100V Half-Rack Audio Power Amplifiers • Specifications 1
Specifications
Extron XPA 1002, XPA 2001-70V, XPA 2001-100V Half-Rack Audio Power Amplifiers
AudioVoltage gainXPA 1002 ��������������������������������������� 16x (24 dB)XPA 2001-70V ������������������������������� 57x (35 dB)XPA 2001-100V ����������������������������� 81x (38 dB)Stereo channel separation �������������� >75 dB @ 1 kHzCMRR �������������������������������������������� 75 dB @ 1 kHz (typical)
Audio inputNumber/signal type ������������������������ 1 stereo or 2 mono, balanced/unbalanced
Connectors ������������������������������ (1) 3�5 mm captive screw connector, 5 poleImpedance ������������������������������� >10k ohms unbalanced/balanced, DC coupled
Nominal level ��������������������������������� +4 dBu (1�23 Vrms), balancedMaximum level ������������������������������� +20 dBu (7�75 Vrms), balancedInput sensitivity
XPA 1002 �������������������������������� +4 dBu (1�23 Vrms)XPA 2001-70V, XPA 2001-100V
+4 dBu (1�23 Vrms) if driven by one input-2 dBu (0�615 Vrms) if both inputs are summed
Input signal detection threshold ����� -40 dBu ±3 dB, balanced
NOTE: 0 dBu = 0�775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
Audio outputNumbers/signal type
XPA 1002 �������������������������������� 1 stereo, 4- or 8-ohm directXPA 2001-70V ������������������������� 1 mono, 70 V lineXPA 2001-100V ����������������������� 1 mono, 100 V line
ConnectorsXPA 1002 �������������������������������� (1) 5 mm screw lock captive screw connector, 4 poleXPA 2001-70V, XPA 2001-100V
(1) 5 mm screw lock captive screw connector, 2 pole
NOTE: These connectors accept wires of 22 AWG to 12 AWG�
-
Extron XPA 1002, XPA 2001-70V, XPA 2001-100V Half-Rack Audio Power Amplifiers • Specifications 2
Load impedanceXPA 1002 �������������������������������� 4 ohms minimumXPA 2001-70V ������������������������� 25 ohms minimumXPA 2001-100V ����������������������� 50 ohms minimum
Amplifier type �������������������������������� Class DOutput power
XPA 1002 �������������������������������� 60 watts rms per channel, 8 ohms, 1 kHz,
-
Extron XPA 1002, XPA 2001-70V, XPA 2001-100V Half-Rack Audio Power Amplifiers • Specifications 3
IdleXPA 1002 ��������������������������� 10 watts (34 BTU/hr)XPA 2001-70V, XPA 2001-100V
12 watts (41 BTU/hr)1/8 power (pink noise)
XPA 1002 ��������������������������� 4 ohms (x2): 18 watts (62 BTU/hr)8 ohms (x2): 15 watts (53 BTU/hr)
XPA 2001-70V ������������������� 70 V (x1): 21 watts (71 BTU/hr)XPA 2001-100V ����������������� 100 V (x1): 20 watts (69 BTU/hr)
Protection �������������������������������������� Clip limiting, thermal, short circuit, DC outputIndication ��������������������������������������� Limiter/Protector LED indicates the onset of clip limiting, thermal cycling, short
circuitMounting
Rack mount ����������������������� Yes, with optional 1U rack shelfEnclosure type �������������������������������� MetalEnclosure dimensions ��������������������� 1�7" H x 8�7" W x 9�5" D (1U high, half rack wide)
(4�3 cm H x 22�1 cm W x 24�1 cm D)Product weight ������������������������������� 2�5 lbs (1�1 kg)Shipping weight ����������������������������� 5 lbs (3 kg)Vibration ���������������������������������������� ISTA 1A in carton (International Safe Transit Association)Regulatory compliance
Safety �������������������������������������� CCC, CE, c-UL, GS, KC Mark, PSE, S Mark, UL, BSMIUL rated for use in plenum airspaces: meets UL 2043 for heat and smoke release; meets UL 60065, IEC 60065, and BSEN 60065 for AV equipment�
EMI/EMC ��������������������������������� CE, CISPR 22 Class B, C-tick, FCC Class B, ICES, VCCI Class BEnvironmental �������������������������� Complies with the appropriate requirements of ENERGY STAR® (ENERGY STAR
qualified amplifier), EU code of conduct, RoHS, WEEEMTBF ��������������������������������������������� 250,000 hoursWarranty ���������������������������������������� 3 years parts and labor
NOTE: All nominal levels are at ±10%�
NOTE: Specifications are subject to change without notice�
-
Extron XPA 2002-70V, XPA 2002-100V Full-Rack Audio Power Amplifiers • Specifications 1
SpecificationsXPA 2002-70V, XPA 2002-100V
AudioVoltage gain
XPA 2002-70V ������������������������� 57x (35 dB)XPA 2002-100V ����������������������� 81x (38 dB)
Crosstalk ���������������������������������������� 75 dB (typical) @ 1 kHzCMRR �������������������������������������������� 75 dB (typical) @ 1 kHz
Audio inputNumber/signal type ������������������������ 2 balanced/unbalancedConnectors ������������������������������������ (2) 3�5 mm captive screw connectors, 3 poleImpedance ������������������������������������� >10k ohms unbalanced/balanced, DC coupledNominal level ��������������������������������� +4 dBu (1�23 Vrms), balancedMaximum level ������������������������������� +21 dBu (8�69 Vrms), balancedInput sensitivity ������������������������������ +4 dBu (1�23 Vrms)Input signal detection threshold ����� -40 dBu ±3 dB, balanced
NOTE: 0 dBu = 0�775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
Audio outputNumber/signal type
XPA 2002-70V ������������������������� 2 channels 70 VXPA 2002-100V ����������������������� 2 channels, 100 V
Connectors ������������������������������������ (2) 5 mm screw lock captive screw connectors, 2 pole
NOTE: These connectors accept wires of 22 AWG to 12 AWG�
Load impedanceXPA 2002-70V ������������������������� 25 ohms minimumXPA 2002-100V ����������������������� 50 ohms minimum
Amplifier type �������������������������������� Class DOutput power
XPA 2002-70V ������������������������� 200 watts rms per channel, 70 V, 1 kHz, 0�1% THDXPA 2002-100V ����������������������� 200 watts rms per channel, 100 V, 1 kHz, 0�1% THD
Frequency response ������������������������ 20 Hz to 20 kHz, ±1 dBTHD + Noise ����������������������������������� 0�1%, 1 kHz, 3 dB below clippingS/N ������������������������������������������������� 100 dB, 20 Hz - 20 kHz, unweightedDamping factor
XPA 2002-70V ������������������������� >100 @ 25 ohmsXPA 2002-100V ����������������������� >100 @ 50 ohms
High pass filterXPA 2002-70V ������������������������� 80 Hz, 12 dB per octave rolloff for 70 V line output (switch selectable)XPA 2002-100V ����������������������� 80 Hz, 12 dB per octave rolloff for 100 V line output (switch selectable)
zz For manuals, use the standard Section style instead of Chapter title, specs sheet or Heading 1, specs stand-alone; and use Heading 1 as usual for “Specifications” if the specs are part of a multitopic chapter�
zz Click the text tool where you want to insert the specs table, select the specs table container paragraph style, then paste in the specs table from the stand-alone master specs sheet�
zz For specifications from template v7�6 or earlier, use this guide to which new paragraph style replaces which old style:
zz Specs8_Heading 2 replaces SpecsSubHdr
zz Specs8_L1 “ Specs7
zz Specs8_L1 cont’d “ Specs7A
zz Specs8_L2 “ Specs7 subcategory
zz Specs8_L3 “ Specs7 sub-subcategory
zz Specs8_Note “ SpecsNote7
zz Specs8_Warning/Caution “ Specs7Warning/caution
zz Specs8_ Revision code “ Revision code
zz The other new styles are required for proper table placement/formatting (one for the entire specs table as placed within a manual section [specs table conteiner], two others [Specs8_Note L1 table and Specs8_Note L2 table] for the note/caution cells within the specs table)�
zz At this time, the notes, cautions, and warnings boxes/tables within specs have to be hand inserted and merged and formatted� Use the existing table styles (NOTE, Caution, and Warning1) for the table boxes�
zz Apply the Specs8_Note L1 table or Specs8_Note L2 table paragraph style (depending on the content to which the note, caution, or warning applies) to the nested note, caution, or warning table� Also apply the Specs8_Note cell insets cell style to the cell containing the note, caution, or warning nested table�
zz Apply the Specs8_Note or Specs8_Warning/Caution paragraph style to the text within the nested note, caution, or warning table�
zz Apply the Specs8_note cell inset cell style to the specs table cell containing the nested table�
For use with user guides (manuals) only (but NOT for stand-alone specs sheets), two bulleted note styles are available to use when you combine a series of notes into one note table:
zz Specs8_Note_bulleted — This is for the first paragaph, and you have to manually insert the bullet character and second tab�
zz Specs8_Note_bulleted, cont'd — This is for susequent paragaphs within a note box� The bullet character is automatically inserted�
Here is an example of how those two styles are used:
NOTES:• Thisisjusttesttexttoshowthestyle.Youwouldn'tnormallyputcompletelyunrelatedtopicstogetherina shared note� All nominal levels are at ±10%� UL rated for use in plenum airspaces: meets UL 2043 for heat and smoke release, excluding the power supply; meets UL 60950 for safety� UL rated for use in plenum airspaces: meets UL 2043 for heat and smoke release, excluding the power supply; meets UL 60950 for safety�
• Specificationsaresubjecttochangewithoutnotice.ULratedforuseinplenumairspaces:meetsUL2043for heat and smoke release, excluding the power supply; meets UL 60950 for safety�
• The 5-pole port supports both hardware and software flow control� The 3-pole ports support software flow control�
-
Extron XPA 2002-70V, XPA 2002-100V Full-Rack Audio Power Amplifiers • Specifications 2
Control/remote — amplifierControl port ����������������������������������� (1) 3�5 mm captive screw connector, 2 polePin configurations
Standby power control (contact closure) Pin 1 = GND, pin 2 = standby
GeneralPower supply ���������������������������������� Internal
Input: 100-240 VAC, 50-60 Hz, 1�5 APower consumption at 115 VAC, 60 Hz
Typical (1/8 power)XPA 2002-70V ������������������� 70 V (x2): 84�5 wattsXPA 2002-100V ����������������� 100 V (x2): 89�6 watts
QuiescentXPA 2002-70V ������������������� 20�8 wattsXPA 2002-100V ����������������� 25�1 watts
Standby �����������������������������������
-
Extron XPA 2002-70V, XPA 2002-100V Full-Rack Audio Power Amplifiers • Specifications 3
Enclosure dimensions ��������������������� 1�7" H x 17�4" W* x 12�0" D (1U high, full rack wide) (4�3 cm H x 44�2 cm W* x 30�5 cm D) *Width excludes rack ears� 19�0" (48�3 cm) W with rack ears�
Product weight ������������������������������� 9�2 lbs (4�2 kg)Shipping weight ����������������������������� 12 lbs (6 kg)Vibration ���������������������������������������� ISTA 1A in carton (International Safe Transit Association)Regulatory compliance
Safety �������������������������������������� CCC, CE, c-UL, GS, KCC, PSE, S-Mark, UL Meets UL 60065, IEC 60065, and BSEN 60065 for AV equipment�
EMI/EMC ��������������������������������� CE, CISPR 22 Class B, CISPR 24, C-tick, EN55103-1, EN55103-2, FCC Class B, ICES, VCCI Class B
Environmental �������������������������� ComplieswiththeappropriaterequirementsofENERGYSTAR®(ENERGYSTARqualified amplifier), EU code of conduct, RoHS, WEEE
Warranty ���������������������������������������� 3 years parts and labor
NOTE:
All nominal levels are at ±10%�
NOTE: Specificationsaresubject
tochange
without
notice.
8�0-121611-D15-111612
-
Extron XPA 2003C-70V, XPA 2003C-100V Full-Rack Audio Power Amplifiers • Specifications 1
SpecificationsXPA 2003C-70V, XPA 2003C-100V
AudioVoltage gain
Channels 1 and 2 �������������������� 23x (27 dB)Channel 3
XPA 2003C-70V ����������������� 57x (35 dB)XPA 2003C-100V ��������������� 81x (38 dB)
Crosstalk ���������������������������������������� 75 dB (typical) @ 1 kHzCMRR �������������������������������������������� 75 dB (typical) @ 1 kHz
Audio inputNumber/signal type ������������������������ 3 balanced/unbalancedConnectors ������������������������������������ (3) 3�5 mm captive screw connectors, 3 poleImpedance ������������������������������������� >10k ohms unbalanced/balanced, DC coupledNominal level ��������������������������������� +4 dBu (1�23 Vrms), balancedMaximum level ������������������������������� +21 dBu (8�69 Vrms), balancedInput sensitivity ������������������������������ +4 dBu (1�23 Vrms)Input signal detection threshold ����� -40 dBu ±3 dB, balanced
NOTE: 0 dBu = 0�775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
Audio outputNumber/signal type
XPA 2003C-70V ����������������������� 2 channels, 4 or 8 ohms 1 channel, 70 V
XPA 2003C-100V ��������������������� 2 channels, 4 or 8 ohms 1 channel, 100 V
Connectors ������������������������������������ (1) 5 mm screw lock captive screw connector, 4 pole (1) 5 mm screw lock captive screw connector, 2 pole
NOTE: These connectors accept wires of 22 AWG to 12 AWG�
Load impedanceChannel 1 or 2 ������������������������ 4 ohms minimumChannel 3
XPA 2003C-70V ����������������� 25 ohms minimumXPA 2003C-100V ��������������� 50 ohms minimum
Amplifier type �������������������������������� Class DOutput power
Channel 1 or 2 (8 ohm) ����������� 100 watts rms per channel, 1 kHz, 0�1% THDChannel 1 or 2 (4 ohm) ����������� 200 watts rms per channel, 1 kHz, 0�1% THDChannel 3
XPA 2003C-70V (70 V output) 200 watts rms per channel, 70 V, 1 kHz, 0�1% THDXPA 2003C-100V (100 V output) 200 watts rms per channel, 100 V, 1 kHz, 0�1% THD
Frequency response ������������������������ 20 Hz to 20 kHz, ±1 dBTHD + Noise
zz For manuals, use the standard Section style instead of Chapter title, specs sheet or Heading 1, specs stand-alone; and use Heading 1 as usual for “Specifications” if the specs are part of a multitopic chapter�
zz Click the text tool where you want to insert the specs table, select the specs table container paragraph style, then paste in the specs table from the stand-alone master specs sheet�
zz For specifications from template v7�6 or earlier, use this guide to which new paragraph style replaces which old style:
zz Specs8_Heading 2 replaces SpecsSubHdr
zz Specs8_L1 “ Specs7
zz Specs8_L1 cont’d “ Specs7A
zz Specs8_L2 “ Specs7 subcategory
zz Specs8_L3 “ Specs7 sub-subcategory
zz Specs8_Note “ SpecsNote7
zz Specs8_Warning/Caution “ Specs7Warning/caution
zz Specs8_ Revision code “ Revision code
zz The other new styles are required for proper table placement/formatting (one for the entire specs table as placed within a manual section [specs table conteiner], two others [Specs8_Note L1 table and Specs8_Note L2 table] for the note/caution cells within the specs table)�
zz At this time, the notes, cautions, and warnings boxes/tables within specs have to be hand inserted and merged and formatted� Use the existing table styles (NOTE, Caution, and Warning1) for the table boxes�
zz Apply the Specs8_Note L1 table or Specs8_Note L2 table paragraph style (depending on the content to which the note, caution, or warning applies) to the nested note, caution, or warning table� Also apply the Specs8_Note cell insets cell style to the cell containing the note, caution, or warning nested table�
zz Apply the Specs8_Note or Specs8_Warning/Caution paragraph style to the text within the nested note, caution, or warning table�
zz Apply the Specs8_note cell inset cell style to the specs table cell containing the nested table�
For use with user guides (manuals) only (but NOT for stand-alone specs sheets), two bulleted note styles are available to use when you combine a series of notes into one note table:
zz Specs8_Note_bulleted — This is for the first paragaph, and you have to manually insert the bullet character and second tab�
zz Specs8_Note_bulleted, cont'd — This is for susequent paragaphs within a note box� The bullet character is automatically inserted�
Here is an example of how those two styles are used:
NOTES:• Thisisjusttesttexttoshowthestyle.Youwouldn'tnormallyputcompletelyunrelatedtopicstogetherina shared note� All nominal levels are at ±10%� UL rated for use in plenum airspaces: meets UL 2043 for heat and smoke release, excluding the power supply; meets UL 60950 for safety� UL rated for use in plenum airspaces: meets UL 2043 for heat and smoke release, excluding the power supply; meets UL 60950 for safety�
• Specificationsaresubjecttochangewithoutnotice.ULratedforuseinplenumairspaces:meetsUL2043for heat and smoke release, excluding the power supply; meets UL 60950 for safety�
• The 5-pole port supports both hardware and software flow control� The 3-pole ports support software flow control�
-
Extron XPA 2003C-70V, XPA 2003C-100V Full-Rack Audio Power Amplifiers • Specifications 2
Channel 1 or 2 ������������������������ 0�1% @ 20 Hz to 20 kHz, 8 ohms, 3 dB below clippingChannel 3 �������������������������������� 0�1%, 1 kHz, 3 dB below clipping
S/N ������������������������������������������������� 100 dB, 20 Hz - 20 kHz, unweightedDamping factor
Channel 1 or 2 ������������������������ >100 @ 8 ohmsChannel 3
XPA 2003C-70V ����������������� >100 @ 25 ohmsXPA 2003C-100V ��������������� >100 @ 50 ohms
High pass filterXPA 2003C-70V ����������������������� 80 Hz, 12 dB per octave rolloff for 70 V line output (switch selectable)XPA 2003C-100V ��������������������� 80 Hz, 12 dB per octave rolloff for 100 V line output (switch selectable)
Control/remote — amplifierControl port ����������������������������������� (1) 3�5 mm captive screw connector, 2 polePin configurations
Standby power control (contact closure) Pin 1 = GND, pin 2 = standby
GeneralPower supply ���������������������������������� Internal
Input: 100-240 VAC, 50-60 Hz, 1�5 APower consumption at 115 VAC, 60 Hz
Typical (1/8 power)XPA 2003C-70V ����������������� 4 ohms (x2) + 70 V: 122�4 watts
8 ohms (x2) + 70 V: 92�2 wattsXPA 2003C-100V ��������������� 4 ohms (x2) + 100 V: 123�1 watts
8 ohms (x2) + 100 V: 94�4 wattsQuiescent
XPA 2003C-70V ����������������� 28�9 wattsXPA 2003C-100V ��������������� 28�1 watts
Standby �����������������������������������
-
Extron XPA 2003C-70V, XPA 2003C-100V Full-Rack Audio Power Amplifiers • Specifications 3
XPA 2003C-100V ��������������� 4 ohms (x2) + 100 V: 48�1 watts (164 BTU/hr) 8 ohms (x2) + 100 V: 44�4 watts (152 BTU/hr)
Thermal dissipation at 230 VAC, 50 HzStandby �����������������������������������
-
Extron XPA 4002, XPA 4002-70V Full-Rack Audio Power Amplifiers • Specifications 1
SpecificationsXPA 4002 Series
AudioVoltage gain
XPA 4002 �������������������������������� 33x (30 dB)XPA 4002-70V ������������������������� 57x (35 dB)
Crosstalk ���������������������������������������� 75 dB (typical) @ 1 kHzCMRR �������������������������������������������� 75 dB (typical) @ 1 kHz
Audio inputNumber/signal type ������������������������ 2 balanced/unbalancedConnectors ������������������������������������ (2) 3�5 mm captive screw connectors, 3 poleImpedance ������������������������������������� >10k ohms unbalanced/balanced, DC coupledNominal level ��������������������������������� +4 dBu (1�23 Vrms), balancedMaximum level ������������������������������� +21 dBu (8�69 Vrms), balancedInput sensitivity ������������������������������ +4 dBu (1�23 Vrms)Input signal detection threshold ����� -40 dBu ±3 dB, balanced
NOTE: 0 dBu = 0�775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
Audio outputNumber/signal type
XPA 4002 �������������������������������� 2 channels, 4 or 8 ohms; or 1 bridged mono, 8 ohmsXPA 4002-70V ������������������������� 2 channels 70 V
ConnectorsXPA 4002 �������������������������������� (1) 5 mm screw lock captive screw connector, 4 poleXPA 4002-70V ������������������������� (2) 5 mm screw lock captive screw connectors, 2 pole
NOTE: These connectors accept wires of 22 AWG to 12 AWG�
Load impedanceXPA 4002 �������������������������������� 4 ohms (8 ohms if bridged) minimumXPA 4002-70V ������������������������� 12�5 ohms minimum
Amplifier type �������������������������������� Class DOutput power
XPA 4002 �������������������������������� 200 watts rms per channel, 8 ohms, 1 kHz, 0�05% THD 400 watts rms per channel, 4 ohms, 1 kHz, 0�05% THD 800 watts rms (bridged mono), 8 ohms, 1 kHz, 0�05% THD
XPA 4002-70V ������������������������� 400 watts rms per channel, 70 V, 1 kHz, 0�1% THDFrequency response ������������������������ 20 Hz to 20 kHz, ±1 dBTHD + Noise
XPA 4002 �������������������������������� 0�1%, 20 Hz to 20 kHz, 8 ohms, 3 dB below clippingXPA 4002-70V ������������������������� 0�1%, 1 kHz, 3 dB below clipping
S/N ������������������������������������������������� 100 dB, 20 Hz - 20 kHz, unweightedDamping factor
XPA 4002 �������������������������������� >100 @ 8 ohmsXPA 4002-70V ������������������������� >100 @ 12�5 ohms
zz For manuals, use the standard Section style instead of Chapter title, specs sheet or Heading 1, specs stand-alone; and use Heading 1 as usual for “Specifications” if the specs are part of a multitopic chapter�
zz Click the text tool where you want to insert the specs table, select the specs table container paragraph style, then paste in the specs table from the stand-alone master specs sheet�
zz For specifications from template v7�6 or earlier, use this guide to which new paragraph style replaces which old style:
zz Specs8_Heading 2 replaces SpecsSubHdr
zz Specs8_L1 “ Specs7
zz Specs8_L1 cont’d “ Specs7A
zz Specs8_L2 “ Specs7 subcategory
zz Specs8_L3 “ Specs7 sub-subcategory
zz Specs8_Note “ SpecsNote7
zz Specs8_Warning/Caution “ Specs7Warning/caution
zz Specs8_ Revision code “ Revision code
zz The other new styles are required for proper table placement/formatting (one for the entire specs table as placed within a manual section [specs table conteiner], two others [Specs8_Note L1 table and Specs8_Note L2 table] for the note/caution cells within the specs table)�
zz At this time, the notes, cautions, and warnings boxes/tables within specs have to be hand inserted and merged and formatted� Use the existing table styles (NOTE, Caution, and Warning1) for the table boxes�
zz Apply the Specs8_Note L1 table or Specs8_Note L2 table paragraph style (depending on the content to which the note, caution, or warning applies) to the nested note, caution, or warning table� Also apply the Specs8_Note cell insets cell style to the cell containing the note, caution, or warning nested table�
zz Apply the Specs8_Note or Specs8_Warning/Caution paragraph style to the text within the nested note, caution, or warning table�
zz Apply the Specs8_note cell inset cell style to the specs table cell containing the nested table�
For use with user guides (manuals) only (but NOT for stand-alone specs sheets), two bulleted note styles are available to use when you combine a series of notes into one note table:
zz Specs8_Note_bulleted — This is for the first paragaph, and you have to manually insert the bullet character and second tab�
zz Specs8_Note_bulleted, cont'd — This is for susequent paragaphs within a note box� The bullet character is automatically inserted�
Here is an example of how those two styles are used:
NOTES:• Thisisjusttesttexttoshowthestyle.Youwouldn'tnormallyputcompletelyunrelatedtopicstogetherina shared note� All nominal levels are at ±10%� UL rated for use in plenum airspaces: meets UL 2043 for heat and smoke release, excluding the power supply; meets UL 60950 for safety� UL rated for use in plenum airspaces: meets UL 2043 for heat and smoke release, excluding the power supply; meets UL 60950 for safety�
• Specificationsaresubjecttochangewithoutnotice.ULratedforuseinplenumairspaces:meetsUL2043for heat and smoke release, excluding the power supply; meets UL 60950 for safety�
• The 5-pole port supports both hardware and software flow control� The 3-pole ports support software flow control�
-
Extron XPA 4002, XPA 4002-70V Full-Rack Audio Power Amplifiers • Specifications 2
High pass filterXPA 4002-70V ������������������������� 80 Hz, 12 dB per octave rolloff for 70 V line output (switch selectable)
Control/remote — amplifierControl port ����������������������������������� (1) 3�5 mm captive screw connector, 2 polePin configurations
Standby power control (contact closure) Pin 1 = GND, pin 2 = standby
GeneralPower supply ���������������������������������� Internal
Input: 100-240 VAC, 50-60 HzPower consumption at 115 VAC, 60 Hz
Typical (1/8 power)XPA 4002 ��������������������������� 4 ohms (x2): 154�0 watts
8 ohms (x2): 93�1 wattsXPA 4002-70V ������������������� 70 V (x2): 143 watts
QuiescentXPA 4002 ��������������������������� 28�3 wattsXPA 4002-70V ������������������� 21 watts
Standby �����������������������������������
-
Extron XPA 4002, XPA 4002-70V Full-Rack Audio Power Amplifiers • Specifications 3
MountingRack mount ����������������������������� Yes,withincludedmountingbrackets
Enclosure type �������������������������������� MetalEnclosure dimensions ��������������������� 1�7" H x 17�4" W* x 12�0" D (1U high, full rack wide)
(4�3 cm H x 44�2 cm W* x 30�5 cm D) *Width excludes rack ears� 19�0" (48�3 cm) W with rack ears�
Product weight ������������������������������� 9�2 lbs (4�2 kg)Shipping weight ����������������������������� 12 lbs (6 kg)Vibration ���������������������������������������� ISTA 1A in carton (International Safe Transit Association)Regulatory compliance
Safety �������������������������������������� CE, c-UL, UL Meets UL 60065, IEC 60065, and BSEN 60065 for AV equipment�
EMI/EMC ��������������������������������� CE, CISPR 22 Class B, CISPR 24, C-tick, EN55103-1, EN55103-2, FCC Class B, ICES, VCCI Class B
Environmental �������������������������� ComplieswiththeappropriaterequirementsofENERGYSTAR®(ENERGYSTARqualified amplifier), EU code of conduct, RoHS, WEEE
Warranty ���������������������������������������� 3 years parts and labor
NOTE:
All nominal levels are at ±10%�
NOTE: Specificationsaresubject
tochange
without
notice.
8�0-121311-D2-111612