1

IMPORTANT:

Go to www.extron.com for the complete

user guide, installation instructions, and

specifications before connecting the

product to the power source.

FOX II T HD 4K • Setup GuideThis guide provides quick start instructions for an experienced installer to set up and operate the Extron FOX II T HD 4K Fiber Optic Transmitter. The transmitter is compatible with all Extron FOX II receivers.

WARNING: The FOX II T HD 4K outputs continuous invisible light (Class 1 rated), which may be harmful to the eyes; use with caution. Plug the attached dust caps into the optical transceivers when the fiber cable is unplugged.

CLASS 1 LASER PRODUCT, see the FOX II T HD 4K User Guide, at www.extron.com.

AVERTISSEMENT : Le FOX II T HD 4K émet une lumière invisible en continu (conforme à la classe 1) qui peut être dangereux pour les yeux, à utiliser avec précaution. Branchez les protections contre la poussière dans l’ensemble émetteur/récepteur lorsque le câble fibre optique est débranché.

Produit laser de classe 1, voir le FOX II T HD 4K User Guide sur www.extron.com (en anglais).

Installation

Step 1 — Mounting

FOX II T HD 4K Transmitter Rear Panel

100-240V ~ 0.5A MAX

50-60 HzHDMI LOOP THRU

L R RS-232

OPTICAL

Tx

RESETLIN

K

LIN

K

Rx

RS-232 IR

ALARM

Tx Rx G 1 2

L R

Tx Rx Tx RxG

AUDIO

INPUTS AUDIORETURN OUT

REMOTE

OV

ER

FI

BE

R FOX T HD 4K

Turn off or disconnect all equipment power sources and mount the transmitter as required. For mounting details and considerations, see the FOX II T HD 4K User Guide at www.extron.com.

Step 2 — Input and Output Connections

a. Connect an HDMI video source to the HDMI input connector. HDMI LOOP THRU

b. If desired, connect an HDMI video display to the Loop-Thru connector for a local display.

c. Connect an audio input device to either the Audio 3.5 mm mini jack or the Audio 5-pole captive screw connector. L R

AUDIO See the drawing below step 2d to make connections on the captive screw connector.

d. For optional returned audio, connect an audio output device to the Audio Return Out 5-pole captive screw connector.

L R

AUDIORETURN OUT

See the drawing below to make connections on the captive screw connector.

ATTENTION:• For unbalanced audio, connect the sleeves to the

ground contact. DO NOT connect the sleeves to the negative (–) contacts.

• Pour l’audio asymétrique, connectez les manchons au contact au sol. Ne PAS connecter les manchons aux contacts négatifs (–).

NOTE: For returned audio, above, you must also do the following:

• Connect an audio input device to the Audio Return In 5-pole captive screw connector on the receiver.

• Install the optional Receiver-Tx-to-transmitter-Rx cable in step 3b.

e. If you want the FOX II units to pass serial or IR data or control signals, such as for serial Rx TxGnd

Tx RxGnd

IR Device

RS-232 Device

RS

-232IR

Tx

Rx

Tx

Rx

G

OVER FIBER

control of a projector, connect the master device to the transmitter and the controlled device to the receiver via the Over Fiber 5-pole captive screw connector.

NOTE: For returned RS-232 and IR responses (from the receiver to the transmitter, you must install the receiver-Tx-to-transmitter-Rx cable in step 3b.

Unbalanced Stereo Output Balanced Stereo Output

Unbalanced Stereo Input Balanced Stereo Input

Do not tin the wires!

Tip

No Ground Here

No Ground Here

Tip

LR

Sleeves

TipRing

TipRing

LR

Sleeves

TipRing

TipRing

LR

SleevesTip

Sleeve

SleeveTip

LR

2

FOX II T HD 4K • Setup Guide (Continued)

f. For remote monitoring of the status of the Rx optical link, connect a locally constructed or obtained device to the two RS-232 ALARM

Tx Rx G 1 2

REMOTE rightmost Alarm poles of the Alarm and Remote RS-232 5-pole captive screw connector. The unit shorts both poles together when no light is detected.

NOTE: The transmitter Alarm port reports the status of the link from the receiver.

g. For remote control of a unit and for loading firmware, connect a host device, such as a computer or control system, to either of the following ports:

Configuration port — The front panel USB mini-B connector. CONFIG

NOTE: Extron recommends performing firmware updates via the Configuration port only.

Remote RS-232 port — The rear panel Remote RS-232 port, the 3 leftmost poles of this 5-pole captive screw connector. RS-232 ALARM

Tx Rx G 1 2

REMOTE The protocol for the Remote port is as follows:

• 9600 baud • no parity • 8 data bits• 1 stop bit • no flow control

Step 3 — Throughput Connections

Receiver

Transmitter11

22

22

11

OPTICAL

Tx

LIN

K

LIN

K

Rx

OPTICAL

Tx

LIN

K

LIN

K

Rx

NOTE: See the two fiber cable connection drawing at right. You can connect the transmitter to a compatible receiver in one of two ways:

• One way (transmitter to receiver) only, perform step 3a.

• Two way (transmitter to receiver and return), perform steps 3a and 3b.

a. Connect the fiber between the Tx port on the transmitter and the Rx port on the receiver (1, at right).

NOTE: Ensure that the transmitter and connected receiver are the same transmission mode, singlemode (SM) or multimode (MM) and that you use the correct SM or MM fiber cable to connect the devices.

b. If you want the receiver to return serial data (such as responses from a controlled device), IR data, or returned audio to the transmitter, connect a cable between the Tx port on the receiver and Rx port on the transmitter (2).

Tx Link and Rx Link LEDs — When lit, the link is active (light is output [Tx] or received [Rx]).

NOTE: The Link LEDs indicate transmission of light only, not whether there is data encoded in the optical link.

3

Operation

After the receiver, the transmitter, and their connected devices are powered up, the system is fully operational. If any problems are encountered, verify that the cables are routed and connected properly and that the display device has a compatible resolution and refresh rate. If problems persist, call the Extron S3 Sales & Technical Support Hotline. See the contact numbers on the last page of this guide for the Extron office nearest you.

Indications

CONFIG SIGNAL

VIDEO AUDIO

HDCP

INPUT

RETURN OUT

SELECTEDID

Power ( ) LED — Indicates that power is applied to the unit.

Video LEDs —

Signal LED — Lights when the unit detects an input video signal.

HDCP LED — Lights when the input signal is HDCP encrypted.

Audio LEDs —

Input LED — Lights when an analog audio or PCM digital audio signal remains above -35 dBV. The LED goes unlit if the audio signal level drops below the threshold for 10 seconds or longer.

Return Out LED — Lights when analog audio is present on the transmitter Return Audio Output connector.

EDID SELECTEDID

EDID Select rotary switch — Set this switch to one of the positions shown in the table below to select the source of the EDID or a specific resolution.

Position 0 — An EDID that has previously been captured from a connected display or manually imported via an SIS command or the Product Configuration Software.

Position 1 — The EDID is selected via the Remote or USB port, using an SIS command or the Extron Product Configuration Software.

Position 2 — Use the EDID from the display connected to the receiver.

NOTE: EDID from the display connected to the receiver requires connection of both fiber cables.

Position 3 — Use the EDID from the display connected to the transmitter loop-through.

Positions 4 through E — Specify a resolution. The table at right identifies the resolutions associated with the switch positions. All resolutions are at 60 Hz with the exception of 4096x2160 (E), which is 30 Hz.

Position F — No EDID assigned.

Pos. Source or resolution Pos. Resolution Pos. Resolution0 User recorded EDID 6 1366x768 C 2048x21601 Selected via RS-232 7 1440x900 D 2560x16002 Display on Rx output 8 1680x1050 E* 4096x21603 Display on Tx loop-through 9 1920x1080 F N/A4 1280x720 A 1920x12005 1280x800 B 2048x1536

* 30 Hz

468-2300-50 Rev. B

01 16

Extron Headquarters+800.633.9876 Inside USA/Canada Only

Extron USA - West Extron USA - East+1.714.491.1500 +1.919.850.1000

+1.714.491.1517 FAX +1.919.850.1001 FAX

Extron Europe+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia+65.6383.4400

+65.6383.4664 FAX

Extron Japan+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East+971.4.299.1800

+971.4.299.1880 FAX

Extron Korea+82.2.3444.1571

+82.2.3444.1575 FAX

Extron India1800.3070.3777

(Inside India Only)

+91.80.3055.3777

+91.80.3055.3737 FAX

© 2015 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com

FOX II T HD 4K • Setup Guide (Continued)

Application Diagram

STANDBY

CLASS 2 WIRING

1

2

XPA 1002

LEVEL

1

12

1

2

LIMITER/

PROTECT

SIGNAL

2

INPUTS

OUTPUT

REMOTE

0

0

VOL/MUTE

10V50 mA

100-240V 1.3A, 50-60Hz

100-24

0V ~ -.-A MAX

50-60 Hz

DISPLAYPORT

L

R

RS-232 OPTICAL

TxRESET

LIN

K

LIN

K

Rx

RS-232IR

ALARM

Tx RxG

12

L

R

Tx RxTx Rx

G

AUDIO

OUTPUTS

AUDIO

RETURN IN REMOTE

OV

ER

FI

BE

R

FOX R DP 4K

POWER

12V

--A MAX

G

TxRx

RTS CTS

COM 1G

TxRx

COM 2

VC

GVOL

RELAYS

1 2 C

1 2 3 4 G

DIGITAL I/O

PWR OUT = 6W

eBUS

+V +S -SG

LAN

IPCP PRO 250

IR/S

S G

100-24

0V ~ 0.5A MAX

50-60 Hz

HDMI

LOOP THRU

L

R

RS-232 OPTICAL

TxRESET

LIN

K

LIN

K

Rx

RS-232IR

ALARM

Tx RxG

12

L

R

Tx RxTx Rx

G

AUDIO

INPUTS

AUDIO

RETURN OUT REMOTE

OV

ER

FI

BE

R

FOX T HD 4K

POWER

SD CARD

USB

PLAY

STATUS

4K HDMI4K HDMI

4K Media Player

MODEL 80

ExtronExtro

nHelp

System

Off

Display

Room

Control

Off

Mute

Screen

Lighting

December 15, 2013 - 7:58 AM

Audio

Control

Volume

Mute

Tuner 1 2 3

VCR

Laptop

PC

DVD

Doc

Cam

Tuner

On

Channel

Last

Presets

More

Presets

32

1 65

4 98

7 Enter

0

RS-232

Ethernet

Ethernet

Audio

4K DisplayPort

ExtronSI 28Surface-mountSpeakers

ExtronXPA 1002PowerAmpli�er

4K Display

Local Monitor Up to 30 km (18.75 miles)

Singlemode FiberSM Model

Audio

RS-232

ExtronFOX T HD 4KFiber Optic Transmitter

ExtronFOX R DP 4KFiber Optic Receiver

ExtronTLP Pro 720T7" Table TopTouchLink Pro Touchpanel

TCP/IPNetwork

Extron IPCP Pro 250IP Link Pro Control Processor