Exam Revision 100 Questions Blacksmiths Tongs Long Handled Pliers 1.What is the correct name for...

Exam Revision

100 Questions

Blacksmiths Tongs

Long Handled Pliers

1. What is the correct name for this tool?

End Cutters

Diagonal Cutters

Engineers Pliers

2. Which of the following images shows a Tee Hinge?

3.What is the correct name for the joint shown on the left

Bridle Joint

Cross halving Joint

Rebate Joint

Mortise and Tenon joint

Dovetail Joint

Through Housing Joint

DowelJoint

5. What do the Vernier callipersshown below read?

10.2mm

5.6mm

3.4mm

3.6mm

6. On the diagram above indicate the dial that makes the blade move in and out.

(The blade adjustment nut )

Block Plane

Smoothing Plane

Jack Plane

Rebate plane

6. What is the correct name for this plane?…

Bull Nose Plane

Shoulder Plane

Compass Plane

Try Plane

Rebate

ChamferGroove

Tongue

7. What is the correct name for a square notch cut along the side of a board?

Tensol Cement

Cascamite

8. What is the most suitable adhesive for gluing

Plastic Laminate to a Kitchen Worktop

Epoxy Resin

PVA

Impact Adhesive

9. .Where on the graph would you find the 50th percentile?

Tensol Cement

Cascamite

10. What is the most suitable adhesive to glue together

this chest of drawers?

Epoxy Resin

PVA

Impact Adhesive

Tensol Cement

Cascamite


acrylic?

Epoxy Resin

PVA

Impact Adhesive

12. What is the correct name for the wood tool shown below?

Parting tool

Gouge

Scraper

Skew Chisel

13. On the Lathe above, where is the Chuck?

Because it has a low melting point

Because it is Non Ferrous Because it is lightweight

Because it melts quickly

14. Why is aluminium the most suitable material for casting in the school workshop?

15. On the diagram to The left where is the

Countersink

16.What is the correct name for the machine shown above

Strip Heater

Vacuum Former

Oven

Fluidising Tank

17) On the diagram above indicate the Drag

18. What is the correct name for the type of tool shown below?

Parting toolKnife ToolRoughing tool

19.What is the correct name for the rivets shown above?

Countersunk rivets

Snap Head Rivets

Blind Rivets

Pop Rivets

20.Where on the graph would you find the 95th percentile?

Vent Spike

Rammer

Gate Cutter

Sprue Pin

21. What is the correct name for thistool?

Draw Pin

Rapping Iron

Striking Off Rod

Cope

22. What is the missing size from the cutting list below

End

80 90 100 110 120 130 140 150 160 170

Click on the correct answer from the choices below

23. On the Lathe above, where is theToolpost?

24. Where is the Compound Slide?

25. Which of the images above shows a Countersunk Wood Screw?

26. What is the correct name for the tool shown below

Riveter

Rivet Punch

Rivet Set & Snap

Rivet Bar

27. What is a hand countersink used for?

Removing Burrs

Drilling Holes

Centre Punching Holes

28) On the diagram above indicate the Cope

29. Which of the following images shows a Butt Hinge?

30. State one safety precaution you would take when turning large diameter work

on the wood lathe?

Slow the lathe down

Speed the lathe up

31. On the image above which tool is a Die


Parting tool

Gouge

Scraper

Skew Chisel

33. Which drawing shows a “Blind Hole”

34. On the image above which tool is the Plug Tap

35. Which metal is most suited to casting in the school workshop?

Brass

Steel Copper

Aluminium


End Cutters

Tinsnips

Shears

Pliers

37. What is the correct name for the joint shown on the left

Bridle Joint

Cross halving Joint

Rebate Joint


Dovetail Joint


DowelJoint

38. Which of the following tools would be used to cut 6mm Dia steel bar?

A Panel Saw

A Coping Saw A Piercing saw

A Jnr Hacksaw

Tensol Cement

Cascamite


this garden bench?

Epoxy Resin

PVA

Impact Adhesive

40. What is another name for Mole Grips?

Long nose Pliers

Engineers Pliers

Self Grip Pliers

Plumbers Wrench

Stillson

41.What is the correct name for the scaled wooden figure often used bydesigners ?

Ergonomics

Ergonome

Aesthetic

Gardengnome

42. Which of the following planes would be used to plane a long uneven edge?

A Block Plane

A Smoothing Plane A Jack Plane

A Try Plane

43. What is the missing sizefrom the cutting list below

Base

5 10 15 20 30 40 70 80 90 120


44. Where is the Forked Centre ?

It can grip round objects like pipe

It is easier to use

It has been drop forged

It is cheaper to buy

45. What major advantage does a Stillson Wrench have over an Adjustable Spanner?


Jewellers Snips

Tin Snips

Diagonal Cutters

Heavy Duty Snips

47. Which tool is designed to cut rivets?

Engineers Pliers Long Nose Pliers

Diagonal Cutters End Cutters

48. Which of the above pictures shows the pattern with the

correct taper?

The study of sensory values,

The Study of the human body in its working environment

49. What does Ergonomics mean?

The study of the dimensions of the human body

50. Where on the graph would you find the 5th percentile?

51. What is the correct name for the drill bits shown on the left

Twist Drills

Forstner bits

Flat Bits

Masonry Bits

Centre drills

52. What is the correct name for the machine shown above

Strip Heater

Vacuum Former

Oven

Fluidising Tank

53. Which machine was used to make the chocolate box inserts shown on the left?

Strip Heater

Vacuum Former

Oven

Fluidising Tank

54.What is the correct name for the process of coating Mild steel in molten Zinc

Galvanizing

Anodising Painting

Plastic dip coating

55. What is the correct name for the joint shown on the left

Bridle Joint

Cross halving Joint

Rebate Joint


Dovetail Joint


DowelJoint

The study of sensory values,

The Study of the human body in its working environment

56. What does Anthropometrics mean?

The study of the dimensions of the human body

57. What is the missing sizefrom the cutting list below

Side

130 140 240 260 280 300 320 340 370 390


58. Where is the Revolving Centre?

59. What is the correct name for the joint shown above

Bridle Joint

Rebate Joint


Dovetail Joint


Dowel Joint

60.What is the correct name for the machine shown above

Strip Heater

Vacuum Former

Oven

Fluidising Tank

61.Which of the images above shows a Round Head Wood Screw?

62.What is the correct name for the joint shown above

Bridle Joint

Rebate Joint


Dovetail Joint


Dowel Joint

63. What is the generic name for these fixings?

Connecting Blocks

Knock down fittings

Connectors

Bolts

64. Where is the Headstock?


Parting tool

Gouge

Scraper

Skew Chisel

66. What is the correct name for the rivets shown above?

Countersunk rivets

Snap Head Rivets

Pop Rivets

67. Which tool is designed for working in tight areas and cutting fine wire?

Engineers Pliers Long Nose Pliers

Diagonal Cutters End Cutters

68. Which of the following images shows a PianoHinge?

69. Which of the following metals is Ferrous (Contains Iron)

Aluminium Copper

Brass Stainless Steel

70. Which of the following metals is an Alloy

Aluminium Copper

Brass Lead

71. Which of the following woodscrews will “Rust” if exposed to the rain

Steel

Brass Stainless Steel

Line

Weight

72. Which of the following terms would not be classed as Aesthetic?

Form

Shape

Proportion

Size

Colour

Centre Punches

Parallel Punches Letter Punches

73. What is the correct name for these tools?

Nail Punches

Steel

Brass Aluminium

74. What is Brazing Rod made from?

Copper

75. Which of the following planes would be used to level off the base of a through housing joint.

76. Letter stamps can be used to stamp letters on which of the following?

High Speed Steel

Aluminium

Acrylic

Perspex

77. What is the correct name for thejoint shown above

Bridle Joint

Cross halving Joint

Rebate Joint


Dovetail Joint


Dowel Joint

78. What is the correct name for the process used to coat the handle of the trowel with plastic?

Galvanizing

Anodising Painting

Plastic dip coating

The Toolmakers clamp can be used to hold small pieces of work while it is being brazed

The Toolmakers clamp can be used to hold small pieces of work while working on them

79. What are Toolmakers clamps used for?

The Toolmakers clamp can be used to hold small pieces of work while it is being welded

Repousse Hammer

Pillar Drill

Parallel Punch

Centre Punch

80. Which tool could be used to create this dimpled pattern on the back of this drawer handle?

Cross Pein Hammer

81. Which of the following tools would be used to cut 0.5mm thick Copper Sheet?

A Panel Saw

A Coping Saw Tin Snips

Engineers Pliers

82. Which metalwork technique is illustrated in the pictures below

Drilling

Facing

Tapering

Knurling

83. What is the correct name for the process shown below

Brazing

Forging

Welding

Casting

Turning

84. On the image above which tool is a Tap


Brazing

Forging

Welding

Casting

Turning

86. The Handle of this boxwill be turned on a lathe.What length of a piece of

wood is required?

Handle


130 140 240 260 290 300 390 440 470 490


Brazing

Forging

Welding

Casting

Turning


Brazing

Forging

Welding

Casting

Knurling

89. What is the correct name for the drill bit shown on the left

Twist Drill

Forstner bit

Flat Bit

Masonry Bit

Centre drill

90. What is the correct name for the machine shown on the left

Arc Welder

Spot Welder

Mig Welder

Tig Welder

91. On the diagram to The left where is the

pilot hole

92. Which of the following hardwoods is most suited for the manufacture of a garden bench?

Rosewood

Teak

Mahogany

Birch

Balsa

93. Which of the following hardwoods is most suited for the manufacture of chopping board?

Rosewood

Beech

Oak

Elm

Balsa

94. What is the correct name for the material shown on the left?

Pine

Blockboard

MDF

Hardboard

Chipboard

Veneered Chipboard

Mahogany

Plywood


Pine

Blockboard

MDF

Hardboard

Chipboard

Veneered Chipboard

Mahogany

Plywood

97) On the diagram above indicate the Runner


Pine

Blockboard

MDF

Hardboard

Chipboard

Veneered Chipboard

Mahogany

Plywood

It takes time to adjust the spanner to the correct size.

The adjustable Spanner has a tendency to round the corners of the nut or bolt.

99. What is the main disadvantage to using an adjustable spanner

Adjustable spanners are bigger than ordinary spanners.

100. Where is the tailstock ?

Well Done

Quiz Completed

Wrong

Click here to try again

Exam Revision 100 Questions Blacksmiths Tongs Long Handled Pliers 1.What is the correct name for...

Documents

Transcript of Exam Revision 100 Questions Blacksmiths Tongs Long Handled Pliers 1.What is the correct name for...