Cat

alog

No.

661

63 *

Ver

sion

#3

EuroStyle 6’X8’Greenhouse

255x193x203 cm / 100”X76”X80”

Keep these instructions in a safe place for future reference.

You must read these instructions carefully before you start to assemblethis greenhouse. Please carry out the steps in the order set out in theseinstructions.

Do not tighten the screws of the Greenhouse until completing on theassembly of the panels.

We strongly recommend the use of work gloves during assembly . Do not attempt toassemble the greenhouse in windy or wet conditions.Do not touch overhead power cables with the aluminum pro�les. Always wear shoesand safety goggles when working with extruded aluminum. Dispose of all plastic bagssafely - keep them out of reach of small children. The greenhouse must be positionedand �xed on a �at level surface. Do not lean against or push the greenhouse duringconstruction. Keep children away from the assembly area. Do not position your greenhousein an area exposed to excessive wind.Do not attempt to assemble this greenhouse if you are tired, have taken drugs or alcoholor if you are prone to dizzy spells. If using a step ladder or power tools ensure that youfollow the manufacturers safety advice. Hot items such as recently used grills, blowtorchesetc. must not be stored in the greenhouse. Ensure there are no hidden pipes or cablesin the ground before inserting the pegs.

SAFETY ADVICE

GENERAL ADVICEInventory all parts before beginning the assembly process to ensure that there are nomissing parts. This is a multi-part assembly that typically requires at least 3 hours. To beconservative, please allow at least 6 hours for assembly process to ensure time forcompletion..Selecting a site - choose a sunny level position away from overhanging trees. If you are�xing your greenhouse directly to a solid concrete foundation use the pre drilled holesin the metal base supplied. The component parts should be checked and laid out closeat hand. Keep all small parts (screws etc.) in a bowl so they do not get lost.Keep roof clear of snow and leaves.

When your greenhouse needs to be cleaned, use a mild detergent solution and rinsewith cold clean water. DO NOT use acetone, abrasive cleaners or other special detergentsto clean the clear panels.Replacement parts - contact Customers service helpline at: 877-627.8476.For additional information please visit our web site: www.palramapplications.com

CARE & MAINTENACE

TOOLS & EQUIPMENT- Silicone sealant applicable to panels & Applicator- Tape measure- Work gloves- Plastic or rubber mallet- Lubricant- Phillipshead-- Step ladder- Drill- Large hammer- Scissors- 2mm (5/64) metal drill bitIf help is required seek professional advice whithin store.

IMPORTANT

ASSEMBLY INSTRUCTIONS

IMPORTANT

- A - Aluminum profiles and parts.

- P5XX – Polycarbonate panels.

- P3XX – Plastic parts.

- M – Metal parts.

- 4XX – Screws, nuts, disks, etc.

Please carefully read all notes, instructions & remarks, BEFORE STARTING THE ASSEMBLY of the greenhouse.

Sort the parts and check against the contents parts list.

Carry out the assembly steps in the order set out in the instructions.

Screws 411 are to be assembled from the outside and nuts 412 from the inside of the greenhouse.

Close screws and nuts (411 & 412), 2-3 turns only, do not fasten them until completion of the assembly,

if not specified otherwise.

Prefix of the parts reference in the assembly instructions:

The end of all profiles, pointed by an arrow, is always upward.

The oval hole in the crossbars A256 should always be assemble to the base of the greenhouse.

The front of the greenhouse is the wall including the door, and the back is the opposite wall.

Firmly connect the greenhouse to a leveled final position immediately after completion of the assembly.

ContentsItem Qty.Inc./mm

A102 44.33”/1126mm 12A103 62.40”/1585mm 1A104 62.40”/1585mm 1

A111 44.69”/1135mm 2A112 44.69”/1135mm 2A113 44.96”/1142mm 1A114 44.96”/1142mm 1A115 44.96”/1142mm 1A116 44.96”/1142mm 1

A131 96.73”/2457mm 2

A141 97”/2463mm 1

A151 23.07”/586mm 1

A171 59.65”/1515mm 2

A172 24.17”/614mm 1

A181 24.17”/614mm 1

A201 61.48”/1560mm 1A202 61.48”/1560mm 1

A211 24.25”/616mm 1

A221 48.82”/1240mm 1

A231 23.82”/604mm 1

A251 24.84”/630mm 1

A253 72.76”/1848mm 1A254 24.02”/610mm 2

A256 50.79”/1290mm 8

A261 15.75”/400mm 1

A271 23.07”/586mm 1

A282 21.77”/553mm 2

A191 24.17”/614mm 1

M243 2

.

Item Qty.Inc./mm Item Qty.Inc./mm

A161 49.07”/1246mm 1

Contents

(2 spare)

K i t A c c e s s o r i e s

Item Qty.Inc./mm

M244 2

P517 10.63” x24.09” 1

P513 22.64” x24.09” 1

1135X612 mm

270X612 mm

575X612 mm

P516 25.79” x24.09” 1666X612 mm

P514 17.32” x24.09” 2440X612 mm

P515 17.32” x24.09” 2440X612 mm

P505 9.45”x23.94” 1240X608 mm

P512 23.62” x21.65” 1600X550 mm

Item Qty.Inc./mm Item Qty.Inc./mm

P311 44.09”/1120mm 42P312 61.42”/1560mm 6P313 9.84”/250mm 2P314 28.74”/730mm 2P315 14.17”/360mm 2

R303 59.6”/1515mm 2

4P324

P302

A306

A323

M307

P301

2

1

2

4

2

431 1/8”X1/2”/1/8’X13 9(1 Spare)

(1 Spare)P316 3.94”/100mm 9

447 M8X0.63”/M8X16 4

411 M6X0.39”/M6X10 85

412 M6 90

421 M4X0.63”/M4X16 6

422 M4 4

445 8X1/2”/M8X7 4

441 M6X1.77”/M6X45 1

442 0.26”/6.5mm 1

443 0.26”/6.5mm 4

P502 44.69”x24.09” 21

P317(1 Spare) 14

1P333

Be sure to bend in the tabs of the base profiles M243 into a 90° anglebefore inserting the screws.Tighten firmly the screws 447 at the lower hole as seen in the lowerpicture.

Attach the sides of the base (M244) to the front and back base pieces(M243).Use the aluminum screws and nuts (411, 412) as shown. Tighten nutcompletely.

1 2

M243

M243

M244

447

M243

Front Side

M243

Connectors

M244

M244

M243

A244

412

411

Back Side

M244

Pay attention to set the aluminum corners (A111, A112) according tothe marks showing bottom and top.

Insert the screws from the outside, tighten nuts only 2-3 turns and leave loose.

NOTE: The assembly of profile A161 should be done simulataneouslywith profile A111.The other side of profile A161 will be connected later.

NOTE: The nuts are to be from the inside. Do not tighten them untilcompletion of the assembly, If not specifically stated otherwise, thisprocedure applies to all cases wherescrews and nuts 411, 412 are to be used.

A111A111

A161

412

411 411

412

411

412

411

from the inside

QTY

2#A111#A112

1#A161

QTY

A161

3

4 Insert the screws from the outside, tighten nuts only 2-3 turns and leave loose.

BACK

(a)

A112

A111

A112

A111411

A111 411

412

QTY

2#A111#A112

A111

2FROM THE INSIDE

NOTE: Screws 411 should be inserted through the lower oftwo holes in profile A253.

NOTE: Profiles A256 are assembled from the inside.The upper holes will be used later on.

Insert the screws from the outside, tighten nuts only 2-3 turns and leave loose.5

BACK

!!

A256 A256

411

412

A256

412

411

BACK

A256 A256

411

412 411

A253

412

2#A256

QTY

1#A253

QTY

412

411

A256

NOTE: The set includes two left and two right “gutter end cups” P324and four plugs. Assemble a plug in all four “gutter end cups” P324. Insert eachone of them into the gutters A131 ends.

NOTE: Leave the end cup open on the side you would like the water to drain. (a)

A131

(b)

(b)

P324

P324

P324

4#A324

QTY

6

2#A131

QTY

Assemble the gutter A131 to the profiles (A111/A112) oneon each end.NOTE: Assemble the crossbars A256 from the insidesimultaneously with the gutter A131 using the same screwsand nuts. The oval holes in A256 must be connected tothe base of the greenhouse.

Insert the screws from the outside, tighten nuts only 2-3 turns and leave loose.7

2#A131

QTY QTY

4#A256

A256

A256

!

BACK

A256

A256

411

412

411

412

411

411

412

A131

A131

A256A256

A256

A256

411

a

A253 BACK

A104

A103

411

A103

A104

!BACK

412

411

A104

b

b

!!

a

a

411

A103A253

The slanted end of the profiles A103 and A104 shouldbe parallel to the downward slope of the roof. Theother end should be insert onto the head of screws411 connecting the crossbars to the base. Insert onescrew 411 in each profile A103, A104 and connect toprofile A253(b).

Insert the screws from the outside, tighten nuts only 2-3 turns and leave loose.8

QTY

1#A1031#A104

Profiles A254 should be connected throughthe lower of the two holes to profiles A111and A112. At their other end, they should beconnected to profiles A201 and A202.

NOTE : Assemble the crossbars A256Simultaneously with the profiles A254 andprofiles A111 and A112, using the same screwsand nuts. The oval holes must be connectedto the base of the greenhouse.

BACK

A202

A256

A256

!

A254

OUTSIDE411

412

A256INSIDE

412

411

A256

INSIDE

OUTSIDE

OUTSIDE

INSIDE

FRONT

411

411

412411

411

412

A201

A254

Insert the screws from the outside, tighten nuts only 2-3 turns and leave loose.9

QTY

2#A254#A256 2

QTY

1#A201

1#A202

A254

Aluminum profiles A113, A114 are to be connected at the front to aluminum profiles A254 using the upper of the two holes. Aluminum profilesA115, A116 are to be connected at the back to aluminum profile A253 - on its two sides using the upper holes. Profiles A113, A114, A115, A116are to be also connected Simulaneously to profiles A131.

A116

411

412

411411

411

411

412

412

412

A113

A253

411

FRONT

BACKA131

A131

A114

A115

FRONT BACK

Insert the screws from the outside, tighten nuts only 2-3 turns and leave loose.10

QTY1#A113111

#A114#A115#A116

Assemble the main beam A141 UNDER A113, A114at the FRONT, A115 and A116 at the BACK .

A141

411

412

411

412

A211

411

412412

411

QTY

1#A141

QTY

1#A211

11 Insert the screws from the outside, tighten nuts only 2-3 turns and leave loose.

Assemble profile A211, from the outside, to profiles A113,A114.

Slide profile A102 on to the preassembled (to the base) screw 411.On the other end slide the head of screw 411 into the groove onprofiles A102, insert the screw into predrilled holes in the gutter A131and close (DO NOT TIGHTEN) with nut 412.

NOTE: Repeat the above assembly procedure to all six profiles A102.You will have to add one screw 411 and nut 412 to each side of thebase in order to assemble the middle profile A102. (* See next step)

A102

A102

412

412

©b®

102

412

411

(c)

A102

412

411

(a)

Insert the screws from the outside, tighten nuts only 2-3 turns and leave loose.12

QTY

6#A102

Slide profile A102 on to the preassembled (to the base) screw 411. Onthe other end slide the head of screw 411 into the groove on profilesA102, insert the screw into predrilled holes in the gutter A131 and close(DO NOT TIGHTEN) with nut 412.

412

411

A102

A102

(a) (b)

412

411

Insert the screws from the outside, tighten nuts only 2-3 turns and leave loose.13

QTY

6#A102

A102

NOTE: The vent in the roof can be inserted replacing one of themiddle sections panels.

In order to assemble the vent you have to insert an additional screw411(b) into two profile A102(b) on both sides of the vent before youconnect it. These two additional screws will be used in the next step.

411

412

(a)

(a)

(b) 411

A102

(a)411

412

411

(a)

(b)

411

412

412

412 412

A102

412

Insert the screws from the outside, tighten nuts only 2-3 turns and leave loose.14

QTY

6#A102

Assemble aluminum profile A251 using the additional screws youinserted on the previous step.

412

A251A251

A251

412

A261

A221(a)

(b)

A211

412

411

442

412

441

(b

A261412

441A261

442

441

(c)

Assemble aluminum profile A221 onto aluminum profile A211(a) .Connect aluminum profile A221(b) and aluminum profile A261 toprofile A113(c).

QTY

1#A251

QTY

1#A221

QTY

1#A261

Insert the screws from the outside, tighten nuts only 2-3 turns and leave loose.15 16

A221

A113

P301

A191

A191

P301

P301

A191

P301

Lay profiles A171 L&R on a flat surface. Lay between them profiles A172,A181 and A191 including preassembled P301 as shown below and tightenall screws.

Door Assembly- When inserting the plastic part No. P301 to aluminumProfile A191 use plastic or rubber mallet. After you inserted part A301push it in approximately 2”/50mm from the profiles A191 end.

17 18

QTY

1#A191

QTY

2#A301

431

421

A172

A172

431

A191

(c)

A181

431

431

431

A171 L & R

QTY

2#A171

1#A172

QTY

1#A181

1#A191

A191

When inserting the panel to the door use a flat surface and if the panel doesnot fit properly, trim the lower and upper corners of the panel.

NOTE: Make sure the grooves on both sides of the panel are properlypositioned along the aluminum-extruded profiles.

C

D

B

D

C

B

A

A

19 20

QTY

1#P502

During the assembly of plastic strips you must put pressure on them untilthey snap into place. Put the pressure at one end of the platic strip andcontinue all the way to the other end.

QTY

1#P517

P502

P502 P517

QTY

2#P311

QTY

2#P313

21

A231

411

412A181

412

411

412

A231

A181

Lay profile A231 on profile A181 and connect them with screws andnuts 411,412.

22

A231

443

421

P302

422

443

422

A231

P302

422

A181

P302443

A231

421

443

QTY

421

#P302

2

2

QTY

443

422

4

2

23

Assemble of the wheels to profile A231.

Note: Make sure to assemble all parts in theorder described in i l lustration below.Part No’ 443 must be assembled, one underscrew 421 head and one between the wheeland profile A231.

VENT SUBASSEMBLYAssemble the handle A306 to profile A271 and tighten screws 421(a) andnuts 422(a). Slide panel P512 into the groove in profile A151(b). Slide profilesA282 on each side of panel P512 until they fit the holes on profile A151ends and the two holes on panel P512(c).

422

A306

421

A271

(a)

When inserting the rubber R303 apply some lubrication solution on thealuminum A171.

R303

24 25

QTY

2#R303

QTY

1#A151

Connect corners with screws 411 and nuts 412.Slide the final profile A271 (with the handle) until it fits the holes on bothprofiles A282 and the two holes on the panel P512(d). Connect cornerswith screws 411 and nuts 412 . Tighten all screws and nuts.

QTY

1#A271

412

412

A282

A282

A151

A271

(b)

411

411

411

411

(c)

(c)

(d)

(b)

P512

1#A282 1#A306

(b)

A251

A141

A306

(b)

(a)

INSIDE

A251

445

A251A323

The brackets A323 should be connected to profile A251 using screws 445(a). To install the vent on main bean aluminum profiles A141, hold it at an angleof 45° relative to the profile’s plane Slide it to the position between the tworoof aluminum profiles AI02(b). The handle A306 should rest on brackets(A323) when the vent is in the closed position.In the open position, the vent can be secured in one of several angles, bycatching a selected hole in the handle with the protruding tip of bracketsA323.

26 27

QTY

2#A323

QTY

4445

QTY

14#P317

28

P317

P317

P317

Noise reduction elements assembly. Put one part of P317 in the middle of eachsection of the wall as shown in the picture below it will be used later on.

(b3)(b1)

(b2)

Note: Make sure the panel is secure in P317 plastic holder (a). Makesure the grooves on both sides of the panel are properly positionedalong the aluminum – extruded profiles.* See also next step.

During the assembly of the plastic strips you must put pressure onthem until they snap into place. Put the pressure at one end andcontinue all the way to the other end-using tool P333, as shown below.

(a) (b)

P502

29

P333

D

A

B

C

D

Pay special attention when assembling the triangular polycarbonate sections(P505, P514 and P515). The plastic strips (P311,P312,P314,P315) should beinstalled only after the polycarbonate panels (P505, P514, and P515, P516) arein position.* (see previous step)

P502

P502

P502

P502

P502

P502

P502

P314

P515

P514

P515

P312x2

P502

P516

P315

P505

P514

12

3

5

4

6

7

9

10

11

12

13

14

15

18

17

16

19

8P311

30

QTY

1#P516

QTY

1#P505

QTY

2#P514

#P515 2

QTY

#P502 13

QTY#P311#P312#P314#P315

24622

When you mount the polycarbonate panels on the roof,insert the panels by sliding them into the gutter as shownin the picture below.Noise Reduction elements assembly. Insert one partP316 in the middel of each of the roof panels and pushit in the groove of the gutter.

* A step ladder will be needed for this step.

(a)

(b)

P513

P311

P311

P311

(c)P316

(c)(c)

P502

P316

1

23

4

5

6

78

31

QTY

#P316 8

QTY

#P311 14

QTY

#P513 1

QTY

#P502 7

307

When fitting the door in its place, pay attention to insert the plastic part(P301) inside the special aluminum rail (A161(a)). It is advised to spreadsome tender lubrication on the rail.After you assemble the door to its place, assemble screw and nut 411,412into the door stopper hole on profile A221(b).

NOTE: Make sure to fasten all screws and nuts.

32 33

(a)

411 (b)

A221

(a)

412

A221

FIRMLY CONNECT the greenhouse to leveled final positionIMMEDIATELY after completion of the assembly, towithstand high winds effects.

The pegs M307 (spikes) are assembled from the inside of the greenhouse.Make sure to use the pre-punched notch in the bottom of the base.

M307

34