etr_241e01p

*ETSI ETR 241TECHNICAL April 1996REPORTSource: ETSI TC-TM Reference: DTR/TM-03014

ICS: 33.040.20

Key words: transmission, PDH, transport, network, architecture

Transmission and Multiplexing (TM);Functional architecture of 2 Mbit/s based

Plesiochronous Digital Hierarchy (PDH) transport networks

ETSIEuropean Telecommunications Standards Institute

ETSI SecretariatPostal address: F-06921 Sophia Antipolis CEDEX - FRANCEOffice address: 650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCEX.400: c=fr, a=atlas, p=etsi, s=secretariat - Internet: [email protected]

Tel.: +33 92 94 42 00 - Fax: +33 93 65 47 16

Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and theforegoing restriction extend to reproduction in all media.

European Telecommunications Standards Institute 1996. All rights reserved.

ETR 241: April 1996

Whilst every care has been taken in the preparation and publication of this document, errors in content,typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to"ETSI Editing and Committee Support Dept." at the address shown on the title page.

ETR 241: April 1996

Contents

Foreword .......................................................................................................................................................5

1 Scope ..................................................................................................................................................7

2 References..........................................................................................................................................7

3 Definitions and abbreviations ..............................................................................................................83.1 Definitions ............................................................................................................................83.2 Abbreviations .......................................................................................................................8

4 Introduction..........................................................................................................................................94.1 Structure ..............................................................................................................................9

5 Transport functional architecture of the PDH network ......................................................................105.1 Introduction ........................................................................................................................105.2 Transport network layers ...................................................................................................105.3 Client/server association....................................................................................................10

6 Application of functional architecture to examples of PDH transport ................................................11

Annex A: Characteristics of PDH transport network layers ....................................................................17

A.1 Path layers description and references.............................................................................................18

A.2 Intra-station sections description and references..............................................................................20

History..........................................................................................................................................................22

ETR 241: April 1996

Blank page

ETR 241: April 1996

Foreword

This ETSI Technical Report (ETR) has been produced by the Transmission and Multiplexing (TM)Technical Committee of the European Telecommunications Standards Institute (ETSI).ETRs are informative documents resulting from ETSI studies which are not appropriate for EuropeanTelecommunication Standard (ETS) or Interim European Telecommunication Standard (I-ETS) status. AnETR may be used to publish material which is either of an informative nature, relating to the use or theapplication of ETSs or I-ETSs, or which is immature and not yet suitable for formal adoption as an ETS oran I-ETS.

ETR 241: April 1996

Blank page

ETR 241: April 1996

1 Scope

This ETR describes the functional architecture of transport networks based on the Plesiochronous DigitalHierarchy (PDH). The document is based on ETR 085 [11], and should be taken as the basis formanagement standards, performance analysis and equipment specification based on the PDH.

Noting that PDH transport networks will exist for many years to come and that many operators areintroducing management features into their PDH transport networks, a rigorously defined transportnetwork architecture provides the necessary foundations for activities such as:

- performance assessment;- availability estimations and protection considerations;- event management;- traffic modelling and topology studies;- organization of data bases on, for example, routing and inventory;- clarification of functionality such as termination.

2 References

This ETR incorporates by dated and undated reference, provisions from other publications. Thesereferences are cited at the appropriate places in the text and the publications are listed hereafter. Fordated references, subsequent amendments to or revisions of any of these publications apply to thisETR only when incorporated in it by amendment or revision. For undated references the latest edition ofthe publication referred to applies.

[1] ITU-T Recommendation G.702 (1990): "Digital hierarchy bit rates".[2] ITU-T Recommendation G.703 (1991): "Physical/electrical characteristics of

hierarchical digital interfaces".

[3] ITU-T Recommendation G.704 (1991): "Synchronous frame structures used at1544, 6312, 2048, 8488 and 44 736 kbit/s hierarchical levels".

[4] ITU-T Recommendation G.73x series: "Principal characteristics of primarymultiplex equipment".

[5] ITU-T Recommendation G.742 (1990): "Second order digital multiplexequipment operating at 8 448 kbit/s and using positive justification".

[6] ITU-T Recommendation G.751 (1990): " Digital multiplex equipments operatingat the third order bit rate of 34 368 kbit/s and the fourth order bit rate of139 64 kbit/s and using positive justification".

[7] ITU-T Recommendation G.755 (1990): "Digital multiplex equipment operating at139 264 kbit/s and multiplexing three tributaries at 44 736 kbit/s".

[8] ITU-T Recommendation G.803 (1993): "Architecture of transport networksbased on the synchronous digital hierarchy (SDH)".

[9] ITU-T Recommendation G.804 (1994): "ATM cell mapping into plesiochronousdigital hierarchy (PDH)".

[10] ITU-T Recommendation G.832 (1994): "Transport of SDH elements on PDHnetworks: Frame and multiplexing structures".

[11] ETR 085 (1993): "Transmission and Multiplexing (TM); Generic functionalarchitecture of transport network".

[12] ETS 300 166 (1993): "Transmission and Multiplexing (TM); Physical andelectrical characteristics of hierarchical digital interfaces for equipment using the2 048 kbit/s-based plesiochronous or synchronous digital hierarchies".

ETR 241: April 1996

[13] ETS 300 167 (1993): "Transmission and Multiplexing (TM); Functionalcharacteristics of 2 048 kbit/s interfaces".

[14] ETS 300 174 (1992): "Network Aspects (NA); Digital coding of componenttelevision signals for contribution quality applications in the range 34 - 45 Mbit/s".

[15] ETS 300 337 (1995): "Transmission and Multiplexing (TM); Generic framestructures for the transport of various signals (including Asynchronous TransferMode (ATM) cells and Synchronous Digital Hierarchy (SDH) elements) at theITU-T Recommendation G.702 hierarchical rates of 2 048 kbit/s, 34 368 kbit/sand 139 264 kbit/s".

3 Definitions and abbreviations

3.1 Definitions

Clause 4 of ETR 085 [11] provides definitions for all generic terms required to describe functionalarchitecture. For the purposes of this ETR, the following abbreviations apply:

NOTE 1: Where a definition contains a term which is itself defined either in ETR 085 [11] or inthis subclause, that term is shown in quotation marks.

path layer network: A "layer network" which is concerned with the transfer of information between pathlayer "access points" in support of one or more "circuit layer networks".

NOTE 2: In the case of 2 Mbit/s based PDH, there are four "path layer networks" with a"client/server" relationship between adjacent "path layer networks". These "path layernetworks" are denoted hereafter as follows:

- P12: 2 048 kbit/s path layer network;- P22: 8 448 kbit/s path layer network;- P31: 34 368 kbit/s path layer network;- P41: 39 264 kbit/s path layer network.

transmission media layer network: A "layer network" which may be media dependent and which isconcerned with the transfer of information between section layer "access points" in support of one or more"path layer networks". It is further divided into a "section" layer network" and a "physical media layernetwork".

section layer network: A "layer network" which is concerned with the transfer of information betweensection layer "access points". In the case of inter-station sections for the PDH, the "characteristicinformation" of the "section layer network" is proprietary and therefore it is not further sub-divided as in thecase of the SDH. In the case of intra-station sections for PDH, the "section layer network" is standardized.

physical media layer network: A "layer network" which is concerned with the actual optical fibre, metallicpair or radio frequency which supports the "section layer network". In the case of inter-station "physicalmedia layer networks" for the PDH, the "characteristic information" is proprietary. In the case of intra-station "physical media layer networks" for the PDH, the "characteristic information" is standardized.

3.2 Abbreviations

For the purposes of this ETR, the following abbreviations apply:

ATM Asynchronous Transfer ModeCMI Coded Mark Inversion (code)HDB High Density Bipolar (code)OAM Operation, Administration and MaintenancePDH Plesiochronous Digital HierarchySDH Synchronous Digital HierarchyTCP Termination Connection PointVC-n Virtual Container (level) n

ETR 241: April 1996

4 Introduction

A telecommunications network is a complex network which can be described in a number of differentways depending on the particular purpose of the description. This ETR describes the network as atransport network from the viewpoint of the information transfer capability in the context of the PDH. Morespecifically, this ETR describes the functional and structural architectures of the 2 Mbit/s based PDHtransport networks. Many of the principles are generic and also applicable to the SDH network.

The generic aspects of the architecture are given in ITU-T Recommendation G.803 [8] and ETR 085 [11]and are therefore not reproduced in this ETR. It is assumed that the reader is familiar with the terminologyand functional architecture given in these documents.

In addition to rigorously describing the functional architecture, this ETR also gives some examples of theapplication of the functional architecture to PDH network structures. Annex A to this ETR also gives thecharacteristics of all PDH transport layers in terms of characteristic information, termination functions andadaptation functions.

This ETR does not consider issues in the circuit layer other than the definition of the inter-layer adaptationbetween the circuit layer network and the transmission network.

NOTE: For the purposes of this ETR, a definition of circuit layer network is given in clause 4 ofETR 085 [11].

4.1 Structure

Subclause 3.1 contains definitions used for defining network architecture. Clause 5 contains the detaileddescription of the architecture in functional terms. The degree of rigour used is consistent with thatrequired for the purposes of network design, network management and network performance analysis.Clause 6 uses the functional description and applies it to actual network topologies, structures andnetwork elements which are likely to be required.

ETR 241: April 1996

5 Transport functional architecture of the PDH network

5.1 Introduction

The functional architecture is described in a generic way in clause 5 of ETR 085 [11]. The description oftransport network layers and client/server associations as they relate to the PDH is given below.

5.2 Transport network layers

Figure 1 illustrates the layered model of the transport network. Features of the layered model are asfollows:

- it is classified broadly into three classes of layer network: a circuit layer network, a path layernetwork and a transmission media layer network;

- the association between any two adjacent layers is a server/client association;- each layer has its own Operation, Administration and Maintenance (OAM) capability.The three classes of layer networks are described as follows:

- circuit layer networks: provide users with telecommunications services such as circuit switchedservices, packet switched services and leased line services. Different circuit layer networks can beidentified according to the services provided. Circuit layer networks are independent of path layernetworks. Examples of equipment in circuit layer networks are switches for various switchedservices and cross-connects for leased line services;

- path layer networks: are used to support different types of circuit layer networks. In the case of PDHthere are four path layer networks: P12, P22, P31 and P4. Path layer networks are independent oftransmission media layer networks;

- transmission media layer networks: are dependent on the transmission medium such as opticalfibre and radio. Transmission media layer networks are divided into section layer networks andphysical media layer networks. Section layer networks are concerned with all the functions whichprovide for the transfer of information between two nodes in path layer networks whereas physicalmedia layer networks are concerned with the actual fibre, metallic pair or radio frequency whichsupports a section layer network.

Figure 1 also shows an example of the association between these three classes of layer networks andshows that the topology of each layer is independent. Each layer network consists of architecturalcomponents which are outlined in subclause 5.2 of ETR 085 [11].

5.3 Client/server association

The client/server association between adjacent layer networks is one where a link connection in the clientlayer network is provided by a trail in the server layer network. More specifically:

- a link connection in the circuit layer is provided by a path in the path layer network, or by a (intra-station) section in the section layer network;

- a link connection in the path layer network is provided by a section in the transmission media layernetwork.

The layered relationship for the PDH based transport network is further illustrated in figure 2. Annex A liststhe client/server associations for various PDH transport network layers.

ETR 241: April 1996

6 Application of functional architecture to examples of PDH transport

In order to illustrate the way that the functional architecture can be used to describe particular transportnetwork scenarios embodying PDH, some examples are given.

Figure 3 shows a possible topology of generic 139 264 kbit/s path and section layer networks supportingdifferent client layer networks.

Figure 4 represents an application of the functional architecture to the case of PDH supporting ATM.

Figure 5 represents an application of the functional architecture to a 64 kbit/s circuit layer supported byvarious PDH path layers and PDH section layers.

Figure 6 represents an application of the functional architecture to the transparent transport of a2 048 kbit/s circuit (P12x) supported by various PDH path layers and PDH section layers.

NOTE: The section layer includes both standardized intra-station (Exy) and non-standardizedinter-station sections.

Transport network An example

Circuit layernetworks

Path layernetworks

layer networks

Packet switchednetwork

Radiotransmission

networkTransmission media

PDH path networks

Leased linecircuit

network

64kbit/s-basedcircuit switched

network

Coaxial cabletransmission

network

Opticaltransmission

network

Figure 1: Example of association between layer networks

ETR 241: April 1996

Circuit Layer Networks

Physical Media Layer

P4xP4aP4sP4e

E0 E4 [2]E12 [2] E22 [2] E31 [2]

P32x [1]P31xP31vP31sP31e

P22xP22e

P12xP12s

P11x [1]

P0x

ATM Virtual Path and Channel Networks

SDH Path Networks

P0x_nc

NOTE 1: P11 and P32 can also be considered to be contained within the circuit layer. They areshown within the path layer because of their role in non-ETSI PDH hierarchies.

NOTE 2: Only intra-station sections are shown. Inter-station section support is not standardized.

ETR 241: April 1996

P4s

laye

r n

etw

ork

VC-12

link c

onne

ction

VC-3 l

ink

conn

ectio

n

VP lin

k c

on

ne

ctio

ns

C ir c

uit

link

c on n

e ct io

n

Circ

uit

laye

r n

etw

ork

ATM

VP

la

yer

net

wo

rkSD

H pa

th la

yer

ne

two

rk

P4s

laye

r n

etw

ork

Sec

tion

la

yer

net

wo

rk

Figure 3: Possible topology of P4s and section layer networks supporting different client layernetworks

ETR 241: April 1996

TCPAPTCP

APTCP

VPT

CP

VPSN

co

nn

ectio

n

VCSN

con

nec

tion

VC tr

ail

VC lin

k co

nn

ectio

n

VP lin

k co

nnec

tion

VPSN

VCSN

Virt

ual

pa

th te

rmin

atio

n

Virt

ual

pa

th su

b-n

etw

ork

Virt

ual

pa

thAP

A

cces

s po

int

TCP

Te

rmin

atio

n co

nn

ectio

n po

int

CP Co

nn

ectio

n po

int

AP

TCP

APTCP

AP

CP

TCP

AP

CP

TCP

APTCP

VPT

AP

VP VPT

VPSN

TCPAP VCT

VPA

VP tr

ail

CP

TCPAPTCP

APTCP

VPTAP

TCP

APTCP

APTCP

VPT

APTCPAP VC

T

VPA

VP tr

ail

ATM

pa

ylo

adAT

M pa

ylo

ad

P4s

trail

P4s

net

wor

k co

nnec

tion

P12s

n

etw

ork

con

nec

tion

E31

net

wo

rk c

on

nec

tion

E12

trai

l

E12

netw

ork

con

nec

tion

VC VCT

VCSN

TCP

TCP

Non

st

anda

rdiz

ed fu

nct

ion

s

P31s

P31s

P31s

P31s

E31

E31

E31

E31

P4s P4

sP4

s

P4s

P12s

E12 E1

2

E12

E12

P12s

P12s

P12s

VP lin

kco

nn

ectio

n

P31s

tr

ail

P31s

n

etw

ork

con

ne

ctio

n

E31

trai

l

P12s

tr

ail

VP n

etw

ork

con

nec

tion

VC lin

kco

nn

ectio

n

Virt

ual

ch

ann

el te

rmin

atio

n

Virt

ual

ch

ann

el su

b-n

etw

ork

Virt

ual

ch

ann

el

Figure 4: An application of the functional architecture to the case of PDH supporting ATM

ETR 241: April 1996

P0x

LCP0

x

SNC

P0x

LCP0

x

LCP0

x

SNC

P12s

NC

P22e

LC

P22e

LC

P22e

LC

P31e

LC

P31e

LC

P31e

LC

E31

NC

No

n

sta

nda

rdis

edse

ctio

ns

E22

NC

E4

NC

P4e

LCP4

e LC

P4e

LC

P31e

NC

E12

NC

P12s

NC

E12

NC

P12s

NC

No

n

sta

nda

rdis

edse

ctio

ns

E31

NC

E4

NC

P12s

P12s

P22e

P22e

P31e

P31e

P31e

P31e P4e

P4e

E12

E12

E31

E31

E31

E31

E22

E22

E4E4

E4E4

E12

E12

P12s

P12s

P12s

P12s

Figure 5: Application of functional architecture to 64 kbit/s circuit layer supported by various PDHpath layers and PDH section layers

ETR 241: April 1996

P3

1e

LC

P3

1e

LC

P3

1e

LC

E3

1 N

CN

on

sta

nd

ar

dis

ed

se

ct i

on

sE

22

NC

E4

NC

P4

e L

CP

4e

LC

P4

e L

C

P3

1e

NC

E1

2 N

CN

on

sta

nd

ar

dis

ed

se

ct i

on

sE

31

NC

E4

NC

P3

1e

P3

1e

P3

1e

P4

e

E1

2E

31

E3

1E

31

E3

1E

22

E2

2E

4E

4E

4

E1

2 N

C

P3

1e

E1

2E

4

P4

e

P1

2x

LC

P2

2x

P2

2x

LC

P2

2x

LC

P2

2x

LC

P2

2x

Figure 6: Application of functional architecture to the transparent transport of a 2 048 kbit/s circuitsupported by various PDH path layers and PDH section layers

ETR 241: April 1996

Annex A: Characteristics of PDH transport network layers

This annex gives the characteristics of the PDH transport network layers defined in ITU-TRecommendations. For each layer a template is given which identifies the characteristic information, theavailable overhead and the client layers which the layer can support. It also identifies the client/serveradaptation functions required to support the client layers. Where possible, relevant ITU-TRecommendations and ETSI Standards are referenced for the detailed characteristics. In some cases,the relevant recommendations do not contain the information in a form which is readily applicable to thetemplate approach. Where this is the case, additional information is given in the template.

For reasons of brevity, a naming convention for the transport network layers is used as follows:

NAMING CONVENTION:

The general scheme for the naming of any path layers is as follows:

- XYYZ

where:

- X = "S" for "SDH";"P" for "PDH";

- YY = 1 to 2 digits identifying the hierarchical level;- Z = "s" for synchronous;

"e" for plesiochronous European mappings;"v" for video;"a" for plesiochronous mappings of ANSI signals;"x" for transparent (or unknown structure for client layers).

Table A.1: PDH ITU-T Recommendation G.702 [1] path and circuit layers

Layer Transmission speed DescriptionP0x 64 kbit/sP0x_nc n x 64 kbit/s

P11x[note] 1 544 kbit/sP12x 2 048 kbit/sP12s 2 048 kbit/s synchronous 125 s frame structure according to ETS 300 167 [13]

P22x 8 448 kbit/sP22e 8 448 kbit/s with 4 plesiochronous 2 048 kbit/sP31x 34 368 kbit/sP31e 34 368 kbit/s with 4 plesiochronous 8 448 kbit/sP31s 34 368 kbit/s synchronous 125 s frame structure according to ETS 300 337 [15]P31v 34 368 kbit/s supporting video circuits according to ETS 300 174 [14]P32x (note) 44 736 kbit/s

P4x 139 264 kbit/sP4e 139 264 kbit/s with 4 plesiochronous 34 368 kbit/sP4s 139 264 kbit/s synchronous 125 s frame structure according to ETS 300 337 [15]P4a 139 264 kbit/s with 3 plesiochronous 44 736 kbit/s signalsNOTE: Paths not belonging to the 2 048 kbit/s based hierarchy are only supported for interworking with

networks based on the 1 544 kbit/s hierarchy.

ETR 241: April 1996

Table A.2: PDH ITU-T Recommendation G.703 intra-station section layers

Layer Transmission speedE0 64 kbit/sE12 2 048 kbit/sE22 8 448 kbit/sE31 34 368 kbit/sE4 139 264 kbit/s

A.1 Path layers description and references

The following templates describe the essential features of PDH path layers (characteristic information,overhead and supported client layers).

P12s Description ReferenceLayer PDH 2 048 kbit/s path ITU-T Recommendation

G.702 [1]Characteristicinformation

125 s frame ITU-T RecommendationsG.702 [1], G.704 [3], G.804[9],ETS 300167 [13],ETS 300 337 [15]

Overhead Bits 1 to 8 of each frame ITU-T RecommendationsG.704 [3], G.804 [9].ETS 300 167 [13],ETS 300 337 [15]

Client layers P0x, P0x_nc (31-byte interleave or 30-byteinterleave with associated signalling in time slot16);ATM virtual paths

ITU-T RecommendationsG.704 [3],G.73x series [4], G.804 [9].ETS 300 167 [13];ETS 300 337 [15]

P22e Description ReferenceLayer PDH 8 448 kbit/s path ITU-T Recommendation

G.702 [1]CharacteristicInformation

100,4 s frame ITU-T RecommendationG.742 [5]

Overhead Bits 1 to 12 of each frame ITU-T RecommendationG.742 [5]

Client Layers P12s, P12x (positive justification, bit interleave) ITU-T RecommendationG.742 [5]





Client Layers P22e, P22x, transparent 8 448 kbit/s circuits,(positive justification, bit interleave)

ITU-T RecommendationG.751 [6]

ETR 241: April 1996



125 s frame ITU-T RecommendationG.804.ETS 300 337 [15]

Overhead 7 bytes ITU-T RecommendationsG.804, G.832,ETS 300 337 [15]

Client layers ATM virtual pathSDH VC-12 pathSDH VC-2, VC-2_nc path

ITU-T RecommendationsG.804, G.832,ETS 300 337 [15]

P31v Description ReferenceLayer PDH 34 368 kbit/s path ITU-T Recommendation


8 ms multiframe based on 179ITU-T Recommendation G.751 [6] frames

ETS 300 174 [14]

Overhead bits 1 to 14 of each frame ETS 300 174 [14]Client layers video container organized in a 125 s frame ETS 300 174 [14]





Client Layers P31e, P31s, P31v, P31x, transparent34 368 kbit/s circuit (positive justification, bitinterleave)

ITU-T RecommendationG.751 [6]



125 s frame ITU-T RecommendationG.804 [9].ETS 300 337 [15]

Overhead 16 bytes ITU-T RecommendationG.804 [9], G.832 [10]ETS 300 337 [15]

Client layers ATM virtual pathSDH VC-12 pathSDH VC-2, VC-2-nc pathSDH VC-3 path

ITU-T RecommendationG.804 [9], G.832 [10],ETS 300 337 [15]

P4a Description ReferenceLayer PDH 139 264 kbit/s path ITU-T Recommendation



Overhead 18 bits ITU-T RecommendationG.755 [7]

Client layers P32x (positive justification, bit interleave) ITU-T RecommendationG.755 [7]

ETR 241: April 1996

A.2 Intra-station sections description and references

The following templates describe the essential features of PDH intra-station section layers (characteristicinformation, overhead and supported client layers).

E0 Description ReferenceLayer PDH ITU-T Recommendation G.703 [2]

64 kbit/s intra-station sectionITU-T RecommendationG.703 [2]ETS 300 166 [12]

Characteristicinformation

unstructured ITU-T RecommendationG.703 [2]ETS 300 166 [12]

Overhead none ITU-T RecommendationG.703 [2]ETS 300 166 [12]

Client layers unstructured (transparent) 64 kbit/s circuit ITU-T RecommendationG.703 [2]ETS 300 166 [12]

E12 Description ReferenceLayer PDH ITU-T Recommendation G.703 [1]

2 048 kbit/s intra-station sectionITU-T RecommendationG.703 [1]ETS 300 166 [12]


2 048 kbit/s High Density Bipolar (HDB)-3coded

ITU-T RecommendationG.703 [1]ETS 300 166 [12]

Overhead HDB-3 coding redundancy ITU-T RecommendationG.703 [1]ETS 300 166 [12]

Client layers P12x, P12s (HDB-3 coding/decoding),unstructured (transparent) 2 048 kbit/s circuit


E22 Description ReferenceLayer PDH 8 448 kbit/s intra-station section ITU-T Recommendation

G.703 [1]ETS 300 166 [12]


8 448 kbit/s HDB-3 coded ITU-T RecommendationG.703 [1]ETS 300 166 [12]


Client layers P22x, P22e (HDB-3 coding/decoding),unstructured (transparent) 8 448 kbit/s circuit


ETR 241: April 1996


G.703 [1]ETS 300 166 [12]


34 368 kbit/s HDB-3 coded ITU-T RecommendationG.703 [1]ETS 300 166 [12]


Client layers P31e, P31s, P31v, P31x (HDB-3coding/decoding),unstructured (transparent) 34 368 kbit/s circuit



G.703 [1]ETS 300 166 [12]


139 264 kbit/s Coded Mark Inversion (CMI)coded


Overhead CMI coding redundancy ITU-T RecommendationG.703 [1]ETS 300 166 [12]

Client layers P4e, P4s, P4a, P4x (CMI coding/decoding),unstructured (transparent) 139 264 kbit/s circuit


ETR 241: April 1996

History

Document history

April 1996 First Edition

ISBN 2-7437-0633-3Dpt lgal : Avril 1996

Foreword1Scope2References3Definitions and abbreviations3.1Definitions3.2Abbreviations

4Introduction4.1Structure

5Transport functional architecture of the PDH network5.1Introduction5.2Transport network layers5.3Client/server association

6Application of functional architecture to examples of PDH transportAnnex A:Characteristics of PDH transport network layersA.1Path layers description and referencesA.2Intra-station sections description and references

History

etr_241e01p

Documents

Transcript of etr_241e01p