ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES...

46
ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC. 9/10

Transcript of ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES...

Page 1: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

ESD BASICS

ESD BASICS

ElectroStatic Discharge (ESD)ESD Control Awareness

©Copyright 2010 DESCO INDUSTRIES INC. 9/10

Page 2: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

ESD Control Training

Introduction

Desco.com

• Per ANSI/ESD S20.20 Training Plan Requirement, "Initial and recurrent ESD awareness and prevention training shall be provided to all personnel”

• Use PowerPoint with Desco 06821 ESD Awareness Booklet

Page 3: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

Prerequisites of ESD Control

The prerequisites of ESD control are:

• Identify ESD Protected Area [EPA]• Identify ESD sensitive items [ESDS]• Provide ESD control training

Page 4: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

ESD BASICS

Protect your work following these guidelines:• Only handle unpackaged ESD sensitive items [ESDS] in the

ESD protected area [EPA] when grounded• Only allow trained or escorted people in the EPA• Ground all conductors including people in the EPA• Use continuous monitors or test wrist straps at least daily• If ESD footwear is used, test at least daily

Page 5: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

ESD BASICS continued

• Visually check that grounding cords are connected

• Keep wristband snug, foot grounder grounding tab in shoe, and ESD smocks covering all clothing on torso

• Keep work area clean and clear of all non essential insulators, or neutralize essential insulators with ionizers with the airflow directed towards the work area

• Use packaging with shielding properties to store or transport ESDS outside the EPA

Page 6: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

• ElectroStatic charges or static electricity can be everywhere, however conductors can be effectively grounded and charges removed to ground.

• A fundamental rule in ESD control is to ground all conductors, including people.

• However, while ESD control is important, it is of secondary importance to employee safety.

• Personnel should not be grounded in situations where they could come into contact with voltage over 250 volts AC.

Grounding & Personnel Safety

Desco.com

Page 7: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

Static Electricity OR Electrostatic Charge

• When 2 Surfaces in Contact then Separate

• Some Electrons Move Causing Imbalance

Defined as Electric charge at rest

All Materials Tribocharge

ElectroStatic ChargeGeneration or Tribocharging

Desco.com

Page 8: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

All Materials Tribocharge

The simple separation of two surfaces, as when tape is pulled off a roll, can cause the transfer ofelectrons between surfaces, generating an ElectroStatic charge.

ElectroStatic Charge Generation:

Desco.com

Page 9: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

Charge Generation or Tribocharging

When two materials make contact and are then separated, a transfer of electrons from one material to the other may take place.

The amount of static electricity generated depends upon the materials subjected to contact or separation, friction, the area of contact or separation, and the relative humidity of the environment.

At lower relative humidity, as the environment is drier, charge generation will increase significantly. Common plastics generally will create the greatest static charges.

Desco.com

Page 10: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

Typical ElectroStatic VoltagesTypical ElectroStatic Voltages

• Walking across a carpet: 1,500 - 35,000 volts

• Walking over untreated vinyl floor: 250 - 12,000 volts

• Vinyl envelope used for work instructions: 600 - 7,000 volts

• Worker at a bench: 700 - 6,000 volts

• Unwinding regular tape: 9,000 - 15,000 volts

Higher number is generated at low humidity

Desco.com

Page 11: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

ESD or ElectroStatic DischargeESD or ElectroStatic Discharge

• Charges Seek Balance• Discharge is Rapid• Creating Heat

If two items are at different electrostatic charge levels, as they approach one another, a spark or Electrostatic Discharge (ESD) can occur. This rapid, spontaneous transfer of electrostatic charge can generate heat and melt circuitry in electronic components.

Desco.com

Page 12: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

Examples Of Electrostatic Discharge or ESD

• Lightning • Zap from a door

There are innumerable ESD events occurring which you do not see or feel. ESD is the hidden enemy in a high tech manufacturing environment.

Desco.com

Page 13: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

Photo of ESD arcing from finger to componentThis is not a computer simulation. Technician was connected to a small magneto.

2,000 / 3,00 volts for a human to feel, even lessthan 100volts mightdamage acomponent

Photos courtesy of Hi-Rel Laboratories, Inc., Spokane, WA

Desco.com

Page 14: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

Types Of ESDDevice DamageTypes Of ESDDevice Damage

• Latent DefectComponent woundedbut Inspection passes

as good

• Catastrophic FailuresInspection is able to detect

failure

Desco.com

Page 15: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

Catastrophic FailuresCatastrophic Failures

• Catastrophic failure causes a failure in an ESD sensitive item that is permanent.

• The ESD event may have caused a metal melt, junction breakdown or oxide failure.

• Normal inspection is able to detect a catastrophic failure.

Desco.com

Page 16: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

Latent DefectLatent Defect

• A latent defect can occur when an ESD sensitive item is exposed to an ESD event and is partially degraded.

• It may continue to perform its intended function, so may not be detected by normal inspection.

• Intermittent or permanent failures may occur at a later time.

Desco.com

Page 17: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

Latent DefectsMore Costly

• Sub Assembly passes inspection• Assembly passes inspection• Product passes inspection• Works a while for customer• Then Upsets & Mysterious Problems• More Returns• More Warranty Costs• Lower Customer Satisfaction

Desco.com

Page 18: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

Repair Costs Increase if Failure Detected Later

One study indicated the repair cost to be:$10 Device$10 Device in board - $100$10 Device in board and in system - $1,000$10 Device and system fails - $10,000

Catastrophic failures are detected during inspection but components with latent defects pass as good

Desco.com

Page 19: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

Latent DefectsMost Frustrating

• Pass inspection as good• May fail later• Cause equipment down time• Costly field repair work• Adversely impacting customer satisfaction

Hidden Enemy ESD damage may occur• Cannot be felt• Cannot be seen• Not detected through normal inspection procedures

Desco.com

Page 20: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

ESD Control

• Any ESD sensitive item should be indentified with the ESD susceptibility symbol, either on itself or its container.• The ESD Susceptibility Symbol (also called Sensitivity or Warning Symbol) identifies items that can be damaged by ESD and should be unpackaged and handled while grounded at an ESD protected workstation.

Desco.com

Page 21: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

Two Types of Materials ConductorsTwo Types of Materials Conductors

• Electrical Current Flows Easily• So Can be Grounded which works effectively

Examples: metals, carbon and people (due to impurities the human body's sweat layer)

Materials that are called dissipative are conductors, able to remove electrostatic charges to ground. The resistance of dissipative materials is the higher portion of the conductive range.

Desco.com

Page 22: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

• Electrical Current Does Not Flow Easily• So Cannot be Grounded

Example: Plastics, glass, and dry air

Two Types of Materials InsulatorsTwo Types of Materials Insulators

Insulators or Non-Conductors

Insulators like this plastic cup will hold the charge and cannot be grounded and "conduct" the charge away.

Desco.com

Page 23: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

Like Germs, ESD Is The Hidden Enemy

Control Germs Sterilization in medicine

You would never consider having surgery in a contaminated operating room, you should never handle electronic assemblies without taking adequate protective measures against ESD

Control ESD

Desco.com

Page 24: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

But to Feel a Discharge it must be about 2,000 volts

Hidden EnemyHidden Enemy

People Discharge Frequently

Desco.com

Page 25: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

Operator’s Part in ESD Control

• Be trained

• Use ESD protective products correctly

• EPA ESD control items are ESD protective products that have been specially formulated to possess at least one of the ESD control properties

1) low charging (antistatic) 2) resistance (conductive or dissipative,

able to be grounded) 3) shielding

Desco.com

ESD Protective

Symbol

Page 26: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

Fundamental ESD Control Principles

• Ground all conductors including people

• ESDS outside the EPA to be in packaging having ESD shielding property

• Remove insulators, substitute with ESD protective versions, or neutralize with ionizers

Desco.com

Page 27: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

• Wrist Straps• Snug on skin

• Clean

• Cord connected to ground

Ground ConductorsIncluding People

Personnel Grounding

Desco.com

Page 28: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

Ground ConductorsIncluding People

• Foot Grounders− Grounding tab under foot− Worn on both feet− Contact to ESD floor

Personnel Grounding

Desco.com

Page 29: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

Wrist Straps

Daily Test Personnel Grounding Devices

• Must work, so test wrist strap daily (or use continuous

monitors)

Foot Grounders

• Must work, so test foot grounder daily

Desco.com

Page 30: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

Workstation Grounding Devices

The purpose of the ESD worksurface is two-fold.

(1)To provide a surface with little to no charge on it.

(2)To provide a surface that will remove ElectroStatic charges from conductors (including ESDS devices and assemblies) that are placed on the surface.

Desco.com

Page 31: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

Worksuface and Operator Responsibility

• Remove unnecessary insulators and personal items• Check that ground wire is attached

Desco.com

"All nonessential insulators such as coffee cups, food wrappers and personal items shall be remove from the workstation or any operation where unprotected ESDS items are handled." [ANSI/ESD S20.20-2007 section 8.3]

Page 32: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

Worksurface Clean Using Only ESD Cleaners

• ESD Worksurface must be maintained• Use only ESD approved cleaner

Desco.com

Page 33: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

Neutralize Insulators Via Ionization

• Ionizer air flow floods area with Ions - Neutralizing ElectroStatic charge

• Insulators cannot be grounded

Desco.com

Page 34: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

Ionizer Can Control Insulators

• Keep insulators a minimum of 12" from ESDS items at all times, or

• Replace regular insulative items with an ESD protective version, or

• Periodically apply a coat of topical antistat, or

• Ionization

Desco.com

Page 35: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

Direct Ionizer Air Flow to ESD Sensitive Items

• Ionizers produce positively and negatively charged ions

• Fans flow air to cover the work area

• Ionization can reduce static charges on an insulator or isolated conductors

• Require periodic emitter pin cleaning filter cleaning, and calibration

Desco.com

Page 36: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

Shield ESD Sensitive Items Outside Protected Area

Faraday Cage effect charges to be

conducted on surface of the conductor.

• Closed Metallized Shielding Bag

Since like charges repel, charges will rest on the exterior. Charges Kept on Outside of Package:

• Covered Conductive Tote Box

Desco.com

Page 37: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

ESD Packaging

Electrostatic discharge shield "A barrier or enclosure that limits the passage of current and attenuates an electromagnetic field resulting from an electrostatic discharge."

• ESD bags should be closed and containers have lids in place• ESD packaging only be opened at an ESD protective

workstation by properly grounded personnel.

Desco.com

Page 38: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

ESD Protected Workstations

An ESD protective workstation is an area that has been established to effectively control electrostatic charges.

• Grounding all conductors (including people)• Removing all insulators• Or neutralizing process essential insulators with an ionizer

Desco.com

Page 39: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

EPA ESD Control Items

• ESD smocks and gloves• ESD Packaging, bags, boxes, etc.• Conductive foam and shunt bars• Antistatic or low charging tape• ESD cleaners and topical antistat• Dissipative bottles and cups• Dissipative binders• Dissipative document and badge holders• Dissipative floor finishes• Conductive paint and epoxy• Conductive and dissipative flooring• ESD hand lotion

Best Practice Remove Insulator or Change to ESD Protective Version

Desco.com

Page 40: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

ReviewReview

REVIEW OF ESD

AWARENESS

Desco.com

Page 41: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

The Prerequisitesof ESD Control

• Identify ESD Protected Area (EPA)

• Identify ESD sensitive items (ESDS)

• Provide ESD control training

Desco.com

Page 42: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

ESD Control Fundamental Principles

• Ground Conductors including people

• Shield ESDS when Stored or Transported outside EPA

• Remove, substitute or Neutralize Insulators with Ionizers

Desco.com

Page 43: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

You Are On The Front Lines Fighting The Hidden Enemy

• Handle unpacked ESDS items only when grounded• Only allow trained or

escorted people in EPA

• Ground all conductors including people in EPA

• Use continuous monitors or test wrist straps at least

daily• If ESD footwear used, test at

least daily Desco.com

Page 44: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

• Visually check that grounding cords are connected

• Keep wristband snug, foot grounder grounding tab in shoe, and ESD smocks covering all clothing on torso

• Keep work area clean and clear of all nonessential insulators, or neutralize essential insulators with ionizers with airflow directed towards the work area

• Use packaging with shielding properties to store or transport ESDS outside the EPA

You Are On The Front Lines Fighting The Hidden Enemy

Desco.com

Page 45: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

The written ESD Control Plan should be in accordance with ANSI/ESD S20.20

• 100 volt Human Body Model limit as a large majority of the ESD products greater than 100 volt sensitivity• ESD Association wrote commercial version of MIL-STD- 1686 for US Department of Defense which has adopted it

ESD training should be repeated as specified in the company’s written ESD Control Plan

Quizzes in Awareness Guide could be “objective evaluation technique to ensure trainee comprehension and training adequacy.”

ANSI/ESD S20.20

Desco.com

Page 46: ESD BASICS ElectroStatic Discharge (ESD) ESD Control Awareness ©Copyright 2010 DESCO INDUSTRIES INC.9/10.

ESD BASICS

ESD BASICS

ElectroStatic Discharge (ESD)ESD Control Awareness

©Copyright 2010 DESCO INDUSTRIES INC. 9/10