ERIKS - Rubber Mouldings

1

R U B B E R T E C H N O L O G Y

R U B B E R M O U L D I N G S

01.02.2006

This information is, to the best of our knowledge, accurate and reliable to the date indicated. The above mentioned data have been obtained by tests we consider as reliable. We don’t assure that the same results can be obtained in other laboratories, using different conditions by the preparation and evaluation of the samples. 01.04.2006

This information is, to the best of our knowledge, accurate and reliable to the date indicated. The above mentioned data have been obtained by tests we consider as reliable. We don’t assure that the same results can be obtained in other laboratories, using different conditions by the preparation and evaluation of the samples.

1

List of rubber mouldings - Ask for our special qualities!

Compound Elastomer Hardness Description/Application Certificates Colour Temp. number IRHD ±5° °C

®®

®

Aflas® 223002 Aflas® FEPM 75° General purpose quality black -10/+250

Neoprene® 32906 Chloroprene CR 70° Standard moulding quality black -35/+110

NBR 36624 Nitrile-NBR 70° Standard moulding quality black -30/+120 Low compression set

NBR 366470 Nitrile-NBR 70° Standard moulding quality black -30/+120

NBR 47702 Nitrile-NBR 90° Standard moulding quality black -30/+120 Low compression set

NBR 366490 Nitrile-NBR 90° Standard moulding quality black -30/+120

HNBR 88625 HNBR 70° General purpose black -30/+150 Low compression set

EPDM 55641 EPDM 70° Peroxide cured black -55/+150 Very low compression set

EPDM 55914 EPDM 70° Sulphur cured / General black -50/+130 purpose moulding quality

EPDM 55914 PC EPDM 70° Peroxide cured / General black -55/+150 purpose moulding quality

EPDM 559273 EPDM 70° Peroxide cured black -40/+150 Very low compression set

EPDM 559302 EPDM 70° Food-Pharma industry FDA-USP XXIII black -55/+150 class VI

EPDM 559306 EPDM 75° For contact with KTW, DVGW, black -55/+150 potable water WRC, W-270

Genuine Viton® GLT 514115 FKM 70° Original Viton GLT for black -40/+200 Low temperatures

Genuine Viton® 514670 FKM 70° General purpose black -20/+200 Low compression set

Genuine Viton® A 51414 black FKM 75° General purpose black -20/+200 Low compression set

2



01.02.2006


®

01.04.2006


2

List of rubber mouldings - Ask for our special qualities!

®®

®®

®

Genuine Viton® A 51414 green FKM 75° General purpose green -20/+200 Low compression set

Genuine Viton® GF 514141 FKM 75° Original Viton GF- black -10/+200 Terpolymer

Genuine Viton® GFLT 514712 FKM 75° Good low temperature and black -40/+200 better chemical resistance Genuine Viton® A SCVBR FKM 75° Semicon industry brown -20/+200 Extra clear

Extreme ETP 514016 FKM 80° Paint and solvent industry black -20/+200 Optimal chemical industry

Genuine Viton® A 514680 FKM 80° Food & Pharma / FDA 177.2600 black -20/+200 Extraction tested

Genuine Viton® A 514320 FKM 90° General purpose black -20/+200 Low compression set

FKM 514676 FKM 75° Very low compression set FDA 177.2600 white -20/+200 USP Class VI

Kalrez® Spectrum™ 6375 FFKM 75° Excell. chemical resistance/ black 275 High temperature stability

Silicone 714742 VMQ 40° Food & Pharma / FDA 177.2600 white -60/+200 Extraction tested

Silicone 714762 VMQ 60° Food & Pharma / FDA 177.2600 white -60/+200 Extraction tested

Silicone ST-EC-60-001 VMQ 60° Standard quality FDA 177.2600 Transl. -60/+200 Peroxide cured

Silicone 714177 VMQ 70° General purpose quality FDA 177.2600 red -60/+200

Silicone 714002 VMQ 75° PT cured FDA 177.2600 Transp. -60/+200 KTW, WRC USP, BGVV

Silicone 714787 VMQ 80° Food & Pharma / FDA 177.2600 transl. -60/+200 Peroxide cured /

Fluorsilicone 614010 FVMQ 80° Low compression set blue -65/+220

®

Compound Elastomer Hardness Description/Application Certificates Colour Temp. number IRHD ±5° °C

3



01.02.2006


3

01.04.2006


Aflas® 75-compound 223002 - Technical Data Sheet

1. IntroductionAflas® 223002 is made of Aflas® FA-100H, a FEPM rubber. Peroxide cured.This material has excellent resistance to acids, steam, hot water, hydraulic and brake fluids.

3. Physical Properties

Chemical Composition :Physical form :Colour :Storage stability * :

Tetrafluorethylene + Propylene-Copolymer (FEPM)MouldingsBlack± 10 years

Test Method Norm Test ValuesSpecific Weight ASTM D 297 1,64Hardness ASTM D 2240 75° ± 5° IRHDTensile Strength at break ASTM D 412 C 18,6 MPaElongation at break ASTM D 412 C 250%Compression Set ASTM D 395 B 25% compression, 24h/200°C 45% 25% compression, 70h/150°C 36%Heat Ageing 72h/200°C ASTM D 573 Hardness Change +1° Tensile Strength Change -2% Elongation Change +4%

4. Temperature Resistance• -10° to +250°C; short time +290°C• TR10 (low temp. resistance): +2°C

5. Chemical ResistanceASTM Oil n° 3 : very goodASTM Fuel C : unsatisfactoryAcetone : unsatisfactoryCrude oils : very goodKerosin : very good Sulphuric acids : very goodMEK : unsatisfactoryMTBE : fairWater : very goodSteam, 200°C : very good

6. Advantages• Good compression set• Very good resistance to water, steam

at high temperatures

7. Other Information• FEPM components are combustible

and decomposition products gener-ate hydrogen fluoride and fluorinated olefins. Do not expose to tempera-tures in excess of 310°C.

• Contains 57% Fluorine.• Other compounds on demand.

2. Product Description

* : Following DIN 7716 conditions

4



01.02.2006


4

01.04.2006


Neoprene® 70-compound 32906 - Technical Data Sheet

1. IntroductionThe ERIKS Neoprene® 70 32906 compound is made of Polychloroprene-Neoprene. It is a standard moulding quality with good ozone and weathering resistance.



Polychloroprene RubberMouldings Black± 6 years

Test Method Norm Test ValuesHardness ASTM D 2240 70° ± 5° IRHDSpecific Weight ASTM D 1817 1,40Tensile Strength at break ASTM D 412 14 N/mm2

Elongation at break ASTM D 412 min. 250%Compression Set ASTM 395 B 22h/100°C, on slab max. 25%Heat Ageing, foll. D573, 70h/100°C ASTM D 2000 Hardness Change +10% Tensile Strength Change -15% Elongation Change -25% max.Immersion in ASTM oil n°1, 70h/100°C ASTM D 2000 Test Method D 471 Hardness Change -10% Tensile Strength Change -20% max. Elongation Change -20% max. Volume Change -10 to +15%Immersion in ASTM oil n°3, 70h/100°C ASTM D 2000 Test Method D 471 Hardness Change -10 to +5° Tensile Strength Change -50% max. Elongation Change -50% max. Volume Change +70%Low temperature Test ASTM D 2000 non brittle after 3 Test Method D 2173 A minutes at -40°C

4. Temperature Resistance• -35° to +110°C

5. Chemical ResistanceAlkali : goodAir : very goodAlcohol : very goodFats : goodMineral oils : good

Vegetable oils : fairEsters : poorOzone : very goodSteam : fairWater : very good

6. Advantages• Good ozone and weathering resistance.• Good flame resistance.



5



01.02.2006


5

01.04.2006


NBR 70-compound 36624 - Technical Data Sheet

1. IntroductionNBR 70-compound 36624 is a Nitrile compound with medium percentage of acrylonitrile. Standard compound with good compression set values for contact with hydraulic fluids.



Chemical Composition :Physical form :Colour :Odour :Storage stability * :

Acrylonitrile / Butadiene RubberMouldingsBlackNone± 7 years

Test Method Norm Test ValuesHardness DIN 53519 70° ± 5° IRHDTensile Strength at break DIN 53504 min 13 MPaElongation at break DIN 53504 min 250%Specific Weight ASTM D 1817 1,25Compression Set DIN 53517 25% compression - 22h/100°C on slab max 12% on O-Ring (3,53 mm) ASTM 395 B max 20%Heat Ageing 70h/100°C DIN 53508 Hardness Change max +6° Volume Change max -2,1% Immersion in ASTM oil n° 3 DIN 53521 Hardness Change max -5° Volume Change max +9% Weight Change max +6%

4. Temperature Resistance• -30° to +120°C• TR10 (low temp. resistance): -16°C

5. Chemical ResistanceAlkali : very goodAir : excellentAlcohol : very goodFats : excellentMineral oils : excellentSilicone oils : excellent Vegetable oils : excellentInorganic acids : excellentKetones : unsatisfactoryEthers : unsatisfactoryOrganic acids : fairInorganic acids : excellent

6. Advantages• Low compression set• Stock item for ca 12.000 dimensions• Standard moulding compound• good balance price/lifetime

7. Other Information• Can be formulated to meet FDA

177.2600 compliance


6



01.02.2006


6

01.04.2006



1. IntroductionNBR 70-compound 366470 is an FDA Nitrile compound with medium percentage of Acrylonitrile.





Test Method Norm Test ValuesHardness DIN 53519 70° ± 5° IRHDTensile Strength at break DIN 53504 min 16,7 MPaElongation at break DIN 53504 min 319%Specific Weight ASTM D 1817 1,20Compression Set DIN 53517 25% compression - 22h/100°C on slab max 20%Heat Ageing 70h/100°C DIN 53508 Hardness Change max +6°



6. Advantages• Can be produced in small quantities• Migration tested in compliance with

FDA 177.2600 class 1 (certificate on demand)

7. Other Information• Compound formulated to FDA

177.2600 for aqueous and fatty foods (class 1)

• Produced with high purity furnace black (less than 10%)


7



01.02.2006


7

01.04.2006



1. IntroductionNBR 90-compound 47702 is a Nitrile compound with medium percentage of Acrylonitrile. Standard compound with good compression set values for contact with hydraulic fluids.





Test Method Norm Test ValuesHardness DIN 53519 90° ± 5° IRHDTensile Strength at break DIN 53504 min 16 MPaElongation at break DIN 53504 min 250%Specific Weight ASTM D 1817 1,25Compression Set DIN 53517 25% compression - 22h/100°C ASTM 395 B on slab max 13% on O-Ring (3,53 mm) max 25%Heat Ageing 70h/100°C DIN 53508 Hardness Change max +4°



6. Advantages• Low compression-set• Stock item for ca 2000 dimensions• Standard moulding compound• Good balance price/lifetime


177.2600 compliance


8



01.02.2006


8

01.04.2006



1. IntroductionNBR 90-compound 366490 is a Nitrile compound with medium percentage of Acrylonitrile. In conformity with FDA 177.2600.





Test Method Norm Test ValuesHardness DIN 53519 90° ± 5° IRHDTensile Strength at break DIN 53504 min 15,6 MPaElongation at break DIN 53504 min 136%Specific Weight ASTM D 1817 1,31Compression Set DIN 53517 25% compression - 22h/100°C on slab max 25%Heat Ageing 70h/100°C DIN 53508 Hardness Change max +5°



6. Advantages• Can be produced in small quantities• Migration tested in compliance with

FDA 177.2600 class 1 (certificate on demand)

7. Other Information• Compound formulated to FDA

177.2600 for aqueous and fatty foods (class 1)

• Produced with high purity furnace black (less than 10%)


9



01.02.2006


9

01.04.2006


HNBR 70-compound 88625 - Technical Data Sheet

1. IntroductionHNBR 70-compound 88625 is a hydrogenated Nitrile compound of standard quality for use in the industry. This compound has good chemical and mechanical properties.




Hydrogenated Acrylonitrile / Butadiene RubberMouldingsBlack± 10 years

Test Method Norm Test ValuesHardness DIN 53505 70° ± 5° Shore ATensile Strength at break DIN 53504 24MPaElongation at break DIN 53504 348%Compression Set DIN 53517 70h/20°C 11,2% 70h/150°C 37,2%Air Ageing 168h/150°C DIN 53508 Tensile Strength Change +9,3% Elongation Change -26,5%Immersion in ASTM oil n°1, 168h/150°C DIN 53521 Tensile Strength Change +2,3% Elongation Change -3,9%

4. Temperature Resistance• -30° to +150°C• TR10 (low temp. resistance): -20°C• Short time up to 180°C

5. Chemical ResistanceAlkali : very goodAir : excellentAlcohol : very goodFats : excellentMineral oils : excellentSilicone oils : excellent Vegetable oils : excellentInorganic acids : excellentKetones : unsatisfactoryEthers : unsatisfactoryOrganic acids : fairOzone : excellent

6. Advantages• Low compression set• Standard moulding compound• good balance price/lifetime


177.2600 compliance• Good for steam up to 130°C


10



01.02.2006


10

01.04.2006This information is, to the best of our knowledge, accurate and reliable to the date indicated. The above mentioned data have been obtained by tests we consider as reliable. We don’t assure that the same results can be obtained in other laboratories, using different conditions by the preparation and evaluation of the samples.

EPDM 70-compound 55641 - Technical Data Sheet

1. IntroductionEPDM 70-compound 55641 is a standard EPDM Terpolymer, Peroxide cured. It has a good compression resistance.



Ethylene / Propylene / Diene Terpolymer - Peroxide curedMouldingsBlackNone7 years

Test Method Norm Test ValuesHardness ASTM D 2240 70° ± 5° IRHDTensile Strength at break ASTM D 412C 2236 psiElongation at break ASTM D 412C 243%Specific Weight ASTM D 1817 1,202Tear Resistance ASTM D 624, die C 33,5 KN/mModulus at 100% ASTM D 412 840 psiCompression Set ASTM 395B 22h/150°C, on slab 22,8%Heat Ageing 70h/150°C ASTM D 865 Hardness Change +5° Tensile Strength Change +3% Elongation Change -19% Weight Change -1,8%Water Resistance 70h/100°C ASTM D 471 after drying 22h/100°C Hardness Change -1° Tensile Strength Change +6% Elongation Change +11% Weight Change -3,8%Low Temperature Test, 3 min/-55°C ASTM D 2137 pass Ozone Resistance, 50 ppm, 70h/40°C pass


5. Chemical ResistanceAir : excellentAlcohol : excellentAlkali : excellentFats : unsatisfactoryHydrocarbons : unsatisfactoryEthers : excellent Esters : unsatisfactoryAcids : fairOils : unsatisfactoryWater : excellentSteam : good

up to 140°COzone : excellent

6. Advantages• Very low compression-set• Excellent steam resistance• Excellent ozone and weathering

resistance

7. Other Information• Compliant with FDA 177.2600.



11



01.02.2006


11

01.04.2006



1. IntroductionEPDM 70-compound 55914 is an EPDM Terpolymer sulphur cured. It is the industrial standard EPDM moulding compound.




Ethylene / Propylene / Diene Terpolymer MouldingsBlackNone± 7 years

Test Method Norm Test ValuesHardness DIN 53519 70° ± 5° IRHDTensile Strength at break DIN 53504 min 10 MPaElongation at break DIN 53504 min 250%Specific Weight ASTM D 1817 1,13Compression Set DIN 53517 25% compression - 22h/100°C on slab max 16% on O-Ring (3,53 mm) max 26%Heat Ageing 70h/100°C DIN 53508 Hardness Change max +14° Volume Change max -10%Acetone immersion 46h/23°C DIN 53521 after drying 22h/100°C Hardness Change max +6° Volume Change max -6% Weight Change max -5%



6. Advantages• Very low compression-set• Stock item for ca 3000 dimensions

7. Other Information• See also our compound 55914PC

for better steam and temperature resistance.


12



01.02.2006


12

01.04.2006


EPDM 70-compound 55914 PC - Technical Data Sheet

1. IntroductionEPDM 70-compound 55914 PC is an EPDM Terpolymer Peroxide cured. It is a high performance EPDM compound.




Ethylene / Propylene / Diene Terpolymer MouldingsBlackNone10 years

Test Method Norm Test ValuesHardness DIN 53519 70° ± 5° IRHDTensile Strength at break DIN 53504 min 10 MPaElongation at break DIN 53504 min 330%Specific Weight ASTM D 1817 1,12Compression Set DIN 53517 25% compression - 22h/150°C on slab max 15% on O-Ring (3,53 mm) max 25%Heat Ageing 70h/100°C DIN 53508 Hardness Change max +12° Volume Change max -4%Acetone immersion 46h/23°C DIN 53521 after drying 22h/100°C Hardness Change max +3° Volume Change max -2% Weight Change max -3%




6. Advantages• Very low compression-set• Stock item for ca 2000 dimensions• Excellent steam resistance• Excellent ozone and weathering

resistance

7. Other Information• See also our compound 55914

which is Peroxide cured.


13



01.02.2006


13

01.04.2006



1. IntroductionEPDM 70-compound 559273 FDA-USP is an EPDM Terpolymer Peroxide cured, specially designed for use in the food & pharma industry and in conformity with FDA 21 CFR 177.2600 and USPXXV class VI.



Chemical Composition :Physical form :ColourStorage stability * :

Peroxide cured, Terpolymer of Ethylene / Propylene and DieneMouldingsBlack± 10 years

Test Method Norm Test ValuesHardness ASTM D 1415 70° ± 5° IRHDTensile Strength at break ASTM D 412 8 MPaElongation at break ASTM D 412 350%Specific Weight ASTM D 1817 1,13Low temperaturetest ASTM D 2137 none brittle after 3 minutes at ISO 2812 -40°CCompression Set ASTM 395 B 25% compression - 22h/100°C ISO 815 on slab 40% Heat resistance 70h/100°C ASTM D 573 Hardness Change +10° Tensile Strength Change -25%



up to 150°COzone : very good

6. Advantages• Very low compression set• Excellent water and steam resistance.• For repeated use in equipment asso-

ciated with the production of food-stuffs intended for human consump-tion, and suitable for the biomedical industry.

7. Other Information• Compound is formulated to FDA

177.2600 (class 1) and USP XXV (class VI).

• Can be produced in small quantities.• Extraction tested (class 1).• Certificates on demand.


14



01.02.2006

This information is, to the best of our knowledge, accurate and reliable to the date indicated. The above mentioned data have been obtained by tests we consider as reliable. We don’t assure that the same results can be obtained in other laboratories, using different conditions by the preparation and evaluation of the samples. 01.04.2006


EPDM 70-compound 559302 black - Technical Data Sheet

1. IntroductionEPDM 70-compound 559302 is an EPDM Terpolymer Peroxide cured. It is a high performance EPDM compound. Conform to FDA 177.2600, 3A Sanitary Standards class I and USP XXIII class VI. Certified by Toxicon Laboratory.




Ethylene / Propylene / Diene Terpolymer MouldingsMouldingsBlackNone10 years

Test Method Norm Test ValuesHardness ASTM D 1415 70° ± 5° IRHDTensile Strength at break ASTM D 412 min 10 MPaElongation at break ASTM D 412 min 300%Specific Weight ASTM D 1817 1,26Compression Set ASTM D 395 25% compression - 22h/100°C on slab max 26%Heat Ageing 70h/100°C ASTM D573 Hardness Change max +12° Volume Change max -4%




6. Advantages• Can be delivered in small quantities

in ca. 10.000 different dimensions• Excellent steam resistance• Excellent ozone and weathering

resistance


14

15



01.02.2006


EPDM 75-compound 559306 black - Technical Data Sheet

1. IntroductionEPDM 75-compound 559306 is an EPDM Terpolymer Peroxide cured. It is a high performance EPDM compound. This compound has most certificates for contact with potable water.




Ethylene / Propylene / Diene Terpolymer MouldingsBlackNone10 years

Test Method Norm Test ValuesHardness DIN 53505 75° ± 5° IRHDTensile Strength at break DIN 53504 min 11 MPaElongation at break DIN 53504 min 257%Specific Weight DIN 53479 1,15Tear Resistance DIN 53507 B 3 N/mm2

Compression Set DIN 53517 A 25% compression - 22h/70°C 8% 25% compression - 22h/125°C 11% on slab 6mm Heat Ageing 68h/125°C ASTM D573 Change in Tensile Strength DIN 53504 +5% Change in Elongation DIN 53504 -7% Change in Hardness DIN 53505 +5% shore A




6. Advantages• Very low compression-set• Excellent steam resistance• Excellent ozone and weathering

resistance• Can be delivered in small quantities

in ca. 10.000 different dimensions

7. Other information• KTW D1/D2 conform for cold and

warm water up to 90°C• DVGW W270 D1/D2 conform• BS 6920 conform for cold and warm

water, WRC registered


01.04.2006


15

16



01.02.2006


16

01.04.2006


Genuine Viton® 70 GLT-compound 514115 - Technical Data Sheet

1. IntroductionOriginal Viton® GLT 514115-compound is based on 100% Genuine Viton® GLT. Products out of this compound are being made according to strict guidelines of DuPont Performance Elastomers. This guarantees a constant high quality level. All products carry the specific, easy recognizable emblem on their package.




Fluorocarbon with 64% Fluorine, Peroxide curedMouldingsBlackExcellent

Test Method Norm Test ValuesHardness ASTM D 2240 70° ± 5° IRHDTensile Strength at break ASTM D412 11,15 MPaElongation at break ASTM D412 260%Specific Weight 1,85Compression Set ASTM D 395 B 25% compression 22h/200°C 24% 166h/175°C 20%

4. Temperature Resistance• -40° to +204°C• TR10 (low temp. resistance): -25°C• Brittle (ASTM D 2137) at -45°C

5. Chemical ResistanceConcentrated acids : excellentAcetone : badHydroxides : excellentBenzene : goodCrude oil : excellentToluene : good Fuel C : excellentMEK : badMTBE : badWater < 100°C : very good

6. Advantages• Low compression set.• Best low temperature resistance of all

Viton® compounds.

7. Safety and HandlingRead and be guided by the recommendations in the DuPont Performance Elastomers techni-cal bulletin H-71129-02,‘Handling Precautions for Viton® and Related Chemicals’.

8. Other Information• Other colours available on request.


®

17



01.02.2006


17

01.04.2006


Genuine Viton® 70-compound 514670 - Technical Data Sheet

1. IntroductionOriginal Viton® 514670-compound is based on a 100% Genuine Viton® polymer. Products out of this compound are being made according to strict guidelines of DuPont Performance Elasomers. This guarantees a constant high quality level. All products carry the specific, easy recognizable emblem on their package. In conformity with FDA 177.2600.



Chemical Composition :

Physical form :Colour :Odour :Solubility :Storage stability * :

Dipolymer of Hexa-Fluoropropylene and Vinylidene Fluoride, plus cure chemicals with 66% FluorineMouldingsBlackNoneLow molecular weight Esters and KetonesExcellent

Test Method Norm Test ValuesHardness DIN 53519 70° ± 5° IRHDTensile Strength at break DIN 53504 min 16,9 MPaElongation at break DIN 53504 min 261%Specific Weight ASTM D 1817 1,82Compression Set DIN 53517 25% compression - 24h/200°C ASTM 395 B on slab max 15%Heat Ageing 7 days/150°C DIN 53508 Hardness Change max -2° Volume Change max +3%


5. Chemical ResistanceConcentrated acids : excellentAcetone : badHydroxides : excellentBenzene : excellentCrude oil : excellentToluene : excellent Fuel C : excellentGasoline : very goodBTM oil 3 : excellentMethylene chloride : very goodMEK : badMTBE : badWater < 100°C : very good

6. Advantages• Very low compression-set• Compression-moulded, produced in

small quantities• Migration tested in compliance with FDA

177.2600 class 1 (certificate on request)

7. Safety and HandlingRead and be guided by the recommendations in the DuPont Performance Elastomers technical bulletin H-71129-02, ‘Handling Precautions for Viton® and Related Chemicals’.

8. Other Information• Produced with high purity furnace black

N772• Contains less than 10% high purity fur-

nace black (class 1)


®

18



01.02.2006


18

01.04.2006



1. IntroductionOriginal Viton® 51414-compound is based on a 100% Genuine Viton® polymer. Products out of this compound are being made according to strict guidelines of DuPont Performance Elasomers. This guarantees a constant high quality level. All products carry the specific, easy recognizable emblem on their package. ERIKS standard original Viton® compound for mouldings.





Copolymer of Hexa-Fluoropropylene and Vinylidene Fluoride, plus cure chemicalsMouldingsBlackNoneLow molecular weight esters and ketonesExcellent



5. Chemical ResistanceConcentrated acids : excellentAcetone : badHydroxides : excellentBenzene : excellentCrude oil : excellentToluene : excellent Fuel C : excellentGasoline : very goodBTM oil 3 : excellentMethylene chloride : very goodMEK : badMTBE : badWater <100°C : good

6. Advantages• Very low compression-set• Stock item for ca 6000 dimensions• Labeled with Viton® stickers

7. Safety and HandlingRead and be guided by the recommendations in the DuPont Performance Elastomers techni-cal bulletin H-71129-02, ‘Handling Precautions for Viton® and Related Chemicals’.

8. Other Information • Can be formulated to meet FDA

177.2600 compliance, or: Mil-R-83248B and AMS7276D


®

19



01.02.2006


19

01.04.2006


Genuine Viton® 75-compound 51414 green - Technical Data Sheet

1. IntroductionOriginal Viton® 51414 green-compound is based on a 100% Genuine Viton® poly-mer. Products out of this compound are being made according to strict guidelines of DuPont Performance Elasomers. This guarantees a constant high quality level. All products carry the specific, easy recognizable emblem on their package.





Copolymer of Hexa-Fluoropropylene and Vinylidene Fluoride, plus cure chemicalsMouldingsGreen - RAL 6011NoneLow molecular weight Esters and KetonesExcellent

Test Method Norm Test ValuesHardness DIN 53519 75° ± 5° IRHDTensile Strength at break DIN 53504 min 12 MPaElongation at break DIN 53504 min 170%Specific Weight ASTM D 1817 2,07Compression Set DIN 53517 25% compression - 24h/200°C ASTM 395 B on slab max 14% on O-Ring (3,53 mm) max 19%Heat Ageing 70h/200°C ASTM 395 B Hardness Change max +5°


5. Chemical ResistanceConcentrated acids : excellentAcetone : badHydroxides : excellentBenzene : excellentCrude oil : excellentToluene : excellent Fuel C : excellentGasoline : very goodBTM oil 3 : excellentMethylene chloride : very goodMEK : badMTBE : badWater < 100°C : good

6. Advantages• Very low compression-set• Stock item for ca 2000 dimensions• Labeled with Viton® stickers



177.2600 compliance, Mil-R-83248B and AMS7276D


®

20



01.02.2006


20

01.04.2006


Genuine Viton® GF 75-compound 514141 - Technical Data Sheet

1. IntroductionOriginal Viton® GF 514141-compound is a polymer with 70% Fluorine content. Cure system is Peroxide.




Terpolymer with 70% Fluorine, Peroxide curedMouldingsBlackNoneExcellent

Test Method Norm Test ValuesHardness ASTM D 2240 75° ± 5° IRHDTensile Strength at break ASTM D412 19,3 MPaElongation at break ASTM D412 328%Specific Weight ASTM D 1817 1,88Compression Set ASTM D 395 B 22h/175°C, on slab 14% Heat Ageing 70h/250°C ASTM D 573 Hardness Change +3,8° Tensile Strenght Change +6,33 MPa Elongation Change +4,4% Weight loss 0,08 grImmersion in Oil n°3, 70h/150°C ASTM D 471 Volume Change +8,74% Hardness Change -1,4° Elongation Change 0% Tensile Strength Change -3,78 MPa

4. Temperature Resistance• 10° to +204°C• TR10 (low temp. resistance): -16°C

5. Advantages• Excellent resistance to oils, organic

fluids (e.g. Gasohol), hot water, steam, inorganic acids and other aqueous media.

• Best chemical resistance of Viton® family.

6. Safety and HandlingRead and be guided by the recom-mendations in the DuPont Performance Elastomers technical bulletin H-71129-02,‘Handling Precautions for Viton® and Related Chemicals’.


®

21



01.02.2006


21

01.04.2006


Genuine Viton® 75 GFLT-compound 514712 - Technical Data Sheet

1. IntroductionOriginal Viton® GFLT 514712-compound is based on 100% Genuine Viton® GFLT. Products out of this compound are being made according to strict guidelines of DuPont Performance Elastomers. This guarantees a constant high quality level. All products carry the specific, easy recognizable emblem on their package.



Fluorocarbon with 67% Fluorine, Peroxide curedMouldingsBlackExcellent

Test Method Norm Test ValuesHardness ASTM D 2240 75° ± 5° IRHDTensile Strength at break ASTM D412 C 16 MPaElongation at break ASTM D412 C 200%Specific Weight ASTM D 1817 1,87Compression Set ASTM D 395 B 25% compression, 70h/200°C 42%Immersion in Fuel C, 168h/23°C ASTM D 471 Volume Change +5%

4. Temperature Resistance• -40° to +204°C• TR10 (low temp. resistance): -21°C• Brittle (ASTM D 2137) at -53°C

5. Chemical ResistanceConcentrated acids : excellentAcetone : badHydroxides : excellentBenzene : excellentCrude oil : excellentToluene : excellent Fuel C : excellentMEK : badMTBE : badWater < 100°C : excellentSteam < 200°C : good

6. Advantages• Low compression set.• Best low temperature resistance of

all Viton® compounds combined with optimal chemical resistance.


8. Other Information• Other colours available on request.


®

22



01.02.2006


Genuine Viton® 75 SCVBR-compound Semicon - Technical Data Sheet

1. IntroductionOriginal Viton® SVCBR-compound is a Genuine Viton® FKM-compound. Products out of this compound are being made according to strict guidelines of DuPont Performance Elastomers. This guarantees a constant high quality level. All products carry the specific, easy recognizable emblem on their package.




Physical form :Colour :Storage stability * :

Bisphenol cured Dipolymer of Hexa-Fluorpropylene and Vinylidene Fluoride with ca. 66% FluorineMouldingsBrownExcellent

Test Method Norm Test ValuesHardness ASTM D 2240 75° ± 5° IRHDTensile Strength at break ASTM D412 13,5 MPaElongation at break ASTM D412 273%Specific Weight ASTM D 1817 2,26Compression Set ASTM D 395 B 25% compression, 22h/175°C, on slab 5%Air Ageing, 70h/200°C ASTM D 573 Volume Change +3%


5. Chemical ResistanceAlcohol : excellentAlkali : badChloride : excellentConcentrated acids : excellentFluor-gas : excellentHalogen solvents : very goodKetones : badn-Methyl Pyrrolindone : goodOxygen : very goodOzone : excellentReactive plasma : very goodStandard Clean 1 : goodUPDI water : very good

6. Advantages• Low compression set.• Vulcanised and post-curred in

vacuum to assure the purity of the compound. Afterwards individually packed in ARGON-environment


8. Other Information• White and green colour available on

request.• Optimal Viton® compound for high

purity semicon applications.


®

01.04.2006


22

23



01.02.2006


23

01.04.2006


Genuine Viton® 80 ETP Extreme 514016 - Technical Data Sheet

1. IntroductionOriginal Viton® 80 ETP Extreme 514016 is a specially formulated fluorpolymer for paint spray industries. Products out of this compound are being made according to strict guidelines of DuPont Performance Elastomers. This guarantees a constant high quality level. All products carry the specific, easy recognizable emblem on their package.




Special Fluorocarbon with 60% Fluorine, Peroxide curedMouldingsBlackExcellent

Test Method Norm Test ValuesHardness DIN 53505 80° ± 5° IRHDTensile Strength at break DIN 53504 20,2 N/mm2

Elongation at break DIN 53504 169%Specific Weight ASTM D 1817 1,86Compression Set DIN 53517 25% compression, 24h/175°C, on slab 26,3%Air Ageing, 72h/200°C DIN 53505 Hardness Change +1°


5. Chemical ResistanceOrganic acids : very goodInorganic acids : excellentAcetone : goodBenzene : very goodCrude oil : excellentMineral oil : excellentToluene : very good Air : very goodMEK : goodMTBE : goodWater < 100°C : very goodSteam < 150°C : very good

6. Advantages• Very low compression set.• Specially resistant to solvents.

7. Safety and HandlingRead and be guided by the recommendations in the DuPont Performance Elastomers techni-cal bulletin H-71129-02,‘Handling Precautions for Viton® and Related Chemicals’.

8. Other Information• Other colours available on request.• Specially developed for paint spray industry.


®

24



01.02.2006


24

01.04.2006



1. IntroductionOriginal Viton® 514680-compound is based on a 100% Genuine Viton® polymer. Products out of this compound are being made according to strict guidelines of DuPont Performance Elasomers. This guarantees a constant high quality level. All products carry the specific, easy recognizable emblem on their package. In conformity with FDA 177.2600.





Dipolymer of Hexa-Fluoropropylene and Vinylidene Fluoride, plus cure chemicalsMouldingsBlackNoneLow molecular weight Esters and KetonesExcellent

Test Method Norm Test ValuesHardness DIN 53519 80° ± 5° IRHDTensile Strength at break DIN 53504 min 14,7 MPaElongation at break DIN 53504 min 146%Specific Weight ASTM D 1817 1,83Compression Set DIN 53517 25% compression - 24h/200°C ASTM 395 B on slab max 15%Heat Ageing 7 days/150°C DIN 53508 Hardness Change max -2° Volume Change max +3%


5. Chemical ResistanceConcentrated acids : excellentAcetone : badHydroxides : excellentBenzene : excellentCrude oil : excellentToluene : excellent Fuel C : excellentGasoline : very goodBTM oil 3 : excellentMethylene chloride : very goodMEK : badMTBE : badWater < 100°C : very goodSteam > 120°C : bad

6. Advantages• Very low compression-set• Compression-moulded, produced in

small quantities• Migration tested in compliance with FDA

177.2600 class 1 (certificate on request)


8. Other Information• Produced with high purity furnace black

N772• Contains less than 10% high purity fur-

nace black (class 1)


®

25



01.02.2006


25

01.04.2006


Genuine Viton®-compound 514320 - Technical Data Sheet

1. IntroductionOriginal Viton® 514320-compound is based on a 100% Genuine Viton® polymer. Products out of this compound are being made according to strict guidelines of DuPont Performance Elasomers. This guarantees a constant high quality level. All products carry the specific, easy recognizable emblem on their package.





Copolymer of Hexa-Fluoropropylene and Vinylidene Fluoride, plus cure chemicalsMouldingsBlackNoneLow molecular weight Esters and KetonesExcellent



5. Chemical ResistanceConcentrated acids : excellentAcetone : badHydroxides : excellentBenzene : excellentCrude oil : excellentToluene : excellent Fuel C : excellentGasoline : very goodBTM oil 3 : excellentMethylene chloride : very goodMEK : badMTBE : badWater < 100°C : very goodSteam > 120°C : bad

6. Advantages• Very low compression-set• Stock item for ca 1800 dimensions



177.2600 compliance, Mil-R-83248B and AMS7276D


®

26



01.02.2006


26

01.04.2006


FKM 75-compound 514676 - Technical Data Sheet

1. IntroductionFKM 514676 is a copolymer formulated in compliance with FDA 177.2600 and USP class VI regulations.



Copolymer with 66% Fluorine Mouldings WhiteExcellent

Test Method Norm Test ValuesHardness ASTM D 1415 75° ± 5° IRHDTensile Strength at break ASTM D 412 10 MPaElongation at break ASTM D 412 200%Compression Set ASTM D 395 25% compression, 24h/200°C 14%Heat Ageing 72h/250°C ASTM D 573 Hardness Change +10° Tensile Strength Change -25% Elongation Change -25%

4. Temperature Resistance• -20 to +200°C• TR10 (low temp.): -16°C

5. Chemical ResistanceConcentrated acids : excellentAcetone : badHydroxides : excellentBenzene : excellentCrude oil : excellentToluene : excellent Fuel C : excellentGasoline : very goodBTM oil 3 : excellentMethylene chloride : very goodMEK : badMTBE : badWater < 100°C : very good

6. Advantages• Very low compression set• Certificates on demand• Extraction tested in compliance with

FDA 177.2600 (class 1)




27



01.02.2006


27

01.04.2006


VMQ Silicone 714742 - Technical Data Sheet

1. IntroductionSilicone compound 714742 is in compliance with FDA 177.2600 for food and pharma. Peroxide cured.




Vinyl Methyl Silicone RubberMouldingsWhiteNone± 10 years

Test Method Norm Test ValuesHardness DIN 53519 40° ± 5° IRHDTensile Strength at break DIN 53504 min 8 MPaElongation at break DIN 53504 min 650%Specific Weight ASTM D 1817 1,17Compression Set DIN 53517 25% compression - 22h/175°C on O-Ring (3,53 mm) max 30%Heat Ageing 70h/200°C DIN 53508 Hardness Change max +9°

4. Temperature Resistance• -60° to +200°C continuous

5. Chemical ResistanceSIP : very good CIP : badHeat Ageing : excellentSterilisation : excellent

6. Advantages• Low compression set• Migration tested in compliance with

FDA 177.2600 class 1 (certificate on request)

7. Other InformationOther colours on demand


28



01.02.2006


28

01.04.2006







Vinyl Methyl Silicone RubberMouldingsWhiteNone± 10 years



5. Chemical ResistanceSIP : very good CIP : badHeat Aging : excellentSterilisation : excellent





29



01.02.2006


29

01.04.2006


VMQ Silicone ST-EC-60-001 - Technical Data Sheet

1. IntroductionSilicone compound ST-EC-60-001 is in compliance with FDA 177.2600, USP VI and BGVV for food, pharma and medical applications. Peroxide cured. Standard cord quality compound.




Vinyl Methyl Silicone RubberMouldingsTranslucentNone± 10 years

Test Method Norm Test ValuesHardness DIN 53519 60° ± 5° IRHDTensile Strength at break DIN 53504 min 10 MPaElongation at break DIN 53504 min 450%Specific Weight ASTM D 1817 1,17Compression Set DIN 53517 25% compression - 22h/175°C on O-Ring (3,53 mm) 25%


5. Chemical ResistanceSIP : very goodCIP : badHeat Ageing : excellentSterilisation : excellent

6. Advantages• Low compression set• Stock item in standard cord dimension• USP Class VI, FDA 177.266, BGVV-

conform• Migration tested in compliance with


7. Other Information• Tolerances in compliance with ISO

3302-1E2 / DIN 7715 E2

• Other colours on demand


30



01.02.2006


30

01.04.2006


VMQ-Silicone compound 714177 - Technical Data Sheet

1. IntroductionSilicone compound 714177 is a general purpose silicone with excellent physical and temperature resistance up to 220°C. Standard compound for mouldings.




Physical form :Colour :Odour :Storage stability * :

Silicone Rubber having both Methyl and Vinyl groups on the Polymer ChainsMouldingsRedNone10 years



5. Chemical ResistanceAir : excellentAlcohol : satisfacoryHydrocarbons : unsatisfactoryFats : goodVegetable oils : goodSilicone oils : goodEthers/esters : unsatisfactoryAcids : goodSteam : poor at high

temperatures; OK up to 130°C

6. Advantages• Very low compression set• Stock item for ca 2000 dimensions

7. Other Information• AS dimensions are available in FDA

177.2600 compliant quality (class 1).• Other colours on demand.• Platinum cured USP class VI on

demand.


31



01.02.2006


31

01.04.2006


VMQ-Silicone compound 714002 - Technical Data Sheet

1. IntroductionPeroxide cured, translucent silicone rubber, 714002. Silicone rubber having both Methyl and Vinyl substituent groups on the polymer chain. Silicone compound from GE BAYER in conformity with USP XXIII class VI. Formulated using only those ingre-dients authorised by BGVV XVA and FDA CFR21 Section 177.2600. Also KTW and WRAS approved.




Vinyl Methyl Silicone Rubber, Peroxide curedMouldingsTransparent10 years

Test Method Norm Test ValuesSpecific Weight ASTM D 247 1,16Hardness ASTM D 1415 (ISO 48) 75° ± 5° IRHDTensile Strength at break ASTM D 412 (ISO 37) 11 MPaElongation at break ASTM D 412 (ISO 37) 500%Compression Set 24h/175°C, on slab ISO 815 41%Low temperature test DIN 53508 non brittle after 3 h at -60°C



6. Advantages• Excellent mechanical, physical and

chemical stability over the tempera-ture range of -40° to +200°C.

• Excellent behaviour when sterilised.• High transparancy grade, intended

for food contact, pharmaceutical and biomedical applications.

• Certificates on demand.


32



01.02.2006


32

01.04.2006







Vinyl Methyl Silicone RubberMouldingsTransparentNone± 10 years





FDA 177.2600 class 1 (certificates on request)



33



01.02.2006


33

01.04.2006


FVMQ Silicone 80 614010 blue - Technical Data Sheet

1. IntroductionSilicone compound 614010 blue is a low compression set Fluorsilicone moulding material with good chemical and fysical resistance at high temperatures up to 220°C, short term even up to 280°C.




Low Compression Set Fluorsilicone (FVMQ)MouldingsBlue± 10 years

Test Method Norm Test ValuesSpecific Weight ASTM D 1817 1,70Hardness ASTM 2240 80° ± 5° Shore ATensile Strength at break ASTM D 412 C 8,44 MPaElongation at break ASTM D 412 C 126,6%Compression Set ASTM D 395 B 22h/175°C, on slab 17,8%Heat Ageing, 70h/225°C ASRM D 573 Hardness Change +1,53° Elongation Change -38,7% Tensile Strength Change -1,87 MPa Weight loss 0,44 grImmersion in Oil n°3, 70h/150°C ASTM D 471 Volume Change +7,92% Hardness Change -5,0° Elongation Change -13,6% Tensile Strength Change -1,12 MPa

4. Temperature Resistance• -65° to +220°C • Short term: 280°C

5. Chemical ResistanceAir : very good Acetone : badHydrocarbons : excellentAmines : bad Mineral oils : very goodGreases : very goodEthers, Esters : fairAcids : good

6. Advantages• Excellent thermal resistance to both

high and low temperatures.• Good with aromatic hydrocarbons,

alcohols and water (not steam)

7. Other Information• Other colours available on demand


ERIKS - Rubber Mouldings

Documents

Transcript of ERIKS - Rubber Mouldings