EQUIPMENT CATALOG SOLIDS CONTROL...
Transcript of EQUIPMENT CATALOG SOLIDS CONTROL...
EQUIPMENT CATALOG
SOLIDS CONTROL EQUIPMENTAND ENVIRONMENTAL SERVICES
FOR DRILLING WASTES MINIMIZATION AND UTILIZATION
3
TABLE OF CONTENTS
TAB
LE
OF
CO
NTE
NTS
About company ............................................................................................................................................................. 4
SOLIDS CONTROL EQUIPMENT
Shale shaker.................................................................................................................................................................. 6
Mud cleaner................................................................................................................................................................... 8
Shale shaker screens ................................................................................................................................................. 10
Decanter centrifuge .................................................................................................................................................... 11
Cuttings dryer.............................................................................................................................................................. 13
Mobile cuttings dryer .................................................................................................................................................. 14
Hopper ......................................................................................................................................................................... 15
Mud gun ....................................................................................................................................................................... 15
Mud mixer ................................................................................................................................................................... 16
Vacuum degasser ....................................................................................................................................................... 17
Centrifugal degasser .................................................................................................................................................. 18
Screw pump ................................................................................................................................................................ 19
Centrifugal pump ........................................................................................................................................................ 20
Screw conveyor ........................................................................................................................................................... 21
ENVIRONMENTAL SERVICES
Cuttings re-injection ................................................................................................................................................... 22
Waste treatment ......................................................................................................................................................... 23
Flocculation and coagulation unit .............................................................................................................................. 25
Thermal desorption system ....................................................................................................................................... 26
Cuttings skips.............................................................................................................................................................. 27
4 5
SOLIDS CONTROL EQUIPMENT
WE HELP OUR CUSTOMERS TO
TECHNICAL SUPPORT
ABOUT COMPANY
MAIN BUSINESS LINES
AKROS was established in 2000 as a trading company specializing in supply of different oil and gas equipment, products
and spare parts into Russia and CIS countries. In 2013 AKROS entered into the fluids engineering business in Western
Siberia.
We offer and successfully deliver standard drilling fluid systems for typical geological and technical conditions, as well
as exclusive technologies providing solutions for specific problems arising during drilling operations.
The support of the local manufacturers and development of hi-tech Russian oilfield services is our main priority.
AKROS is always looking for Russian prototypes of western equipment or for partners to design such equipment and
to manufacture it in Russia.
As part of our commitment to high-quality services, competitive pricing and experienced management team, AKROS
rapidly wins respect and recognition of oil and gas operators and drilling companies in Russia and has a distinct goal
to become a leader in the key markets of drilling fluids and environmental solutions in Russia.
The equipment is manufactured using production facilities of GN Solids Control, our partner company.
AKROS offers leading-edge solids control solutions, developed for optimization of the drilling process, that allow reduction
of the mud loss and environmental impact.
We see our main goal as providing the equipment, materials and services that meet the most demanding requirements
and expectations of our customers.
AKROS puts special emphasis on the quality of its products and pursues new technologies in the field of the solids control
equipment manufacture. All products are certified to APIQ1, ISO/TS 29001.
Another important aspect of AKROS business is seeing to it that all processes are in systematic, consistent and continuous
improvement.
This permits the Company to achieve its goals, unlock the potential and aim for progressive development.
▪ optimize the economics and improve cost efficiency of drilling operations
▪ increase the recovery of valuable drilling mud
▪ find the best solutions for minimization and disposal of drilling waste in accordance with the legislative environmental
requirements
▪ maintain the drilling mud parameters in order to increase the efficiency of drilling without impairment of the reservoir
properties
▪ an extensive technical support network
▪ technical audits
▪ recommendations for optimization and upgrading of the circulation systems
▪ aftermarket service and support
DRILLINGFLUID
SERVICES
AKROS provides profes-sional service in develop-ment of optimal drilling fluid formulations consid-ering the geological and technical conditions in area and regional features of drilling.
AKROS offers advanced solids control technologies developed to optimize the drilling process. It allows reducing loss of drilling fluid and keeping its parameters to increase drilling efficiency without impairing reservoir prope-rties of formation.
AKROS provides services for minimizing and utilizing drilling wastes, including technologies for slop-mud processing, cutting re-injection into the reservoir, and also offers an innovative floc-culant for recovering oil-based drilling fluids.
AKROS developed a range of technologies and services for soft well killing to improve quality, shorten well workover time and reduce risks of drilling problems.
SUPPLY OF SOLIDS CONTROL
EQUIPMENT
ENVIRONMENTAL SERVICES
WORKOVER AND COMPLETION SOLUTIONS
AB
OU
T CO
MP
AN
Y
6 7
SHALE SHAKER FALCON
SHALE SHAKER FALCON
FEATURES & BENEFITS
High performance FALCON Shale Shakers are designed to efficiently remove solids from drilling fluids. Being the primary
solids separation tool FALCON Shale Shakers enable to maintain rheological parameters and reduce dilution volumes.
▪ patent electric shaker deck angle adjustable while working, mechanical deck angle adjustment for backup application
▪ patent tighten rubber sealing for shaker deck and screen, long life and easy replacement
▪ shaker bottom deck made from stainless steel for long service life
▪ heat treatment on complete shaker deck for High G force operation
▪ pretensioned Shaker screen for fast screen replacement
▪ famous Brand Vibration Motors : IEC Ex, ATEX and UL Certified
▪ electrical components: SIEMENS, Schneider Brand
▪ flexible feeding type including Weir Feed, Top Feed, and Hopper Feed for different applications
MODEL FALCON 3 FALCON 4
Vibration Mode Linear Motion
Capacity (m3/h) 120 (528GPM) 140 (616GPM)
Vibration Motor (Kw) 2 x 1.72
Screen Qty(Pcs) 3 4
Screen Size x L x W (mm) 585 x 1165
Screen Area(m2) 2.05 2.73
Adjustable G Force ≤7.5G
Vibration Amplitude (mm) 4.14 ~5.96
Deck Angle Range -1 ~+5°(Electric & Mechanical)
Feeding Type Box Feeder/Weir Feeder
Weir Height (mm) 735
EX Standard ExdIIBt4
Weight(Kg) 1540 1589
Dimension: L x W x H (mm) 2377 x 1645 x 1428 2933 x 1700 x 1265
SH
AL
E S
HA
KE
R F
ALC
ON
FALCON 3
COMPACT HIGH EFFICIENCY
SHALE SHAKER
FALCON 4
HIGH EFFICIENCY
SHALE SHAKER
▪ compact dimensions enable operation in limited
space with preservation of high technical performance
▪ enhanced force of 7.5 G
▪ high shale shaker capacity
▪ explosion proof design of electric motors
▪ efficient solids removal
▪ high speed of cuttings transportation
▪ enhanced force of 7.5 G
▪ explosion proof design of electric motors
FALCON 3
FALCON 4
SH
AL
E S
HA
KE
R F
ALC
ON
SOLIDS CONTROL EQUIPMENT
8 9
MUD CLEANER FALCON
MUD CLEANER FALCON
For effective removal of fine cuttings AKROS offers a high efficiency mud cleaner based on shale shakers FALCON 3
and FALCON 4, which is a 3 step cleaning system designed for processing of both weighted and non weighted drill mud.
MU
D C
LE
AN
ER
FA
LCO
N
MU
D C
LE
AN
ER
FA
LCO
N
MODEL FALCON 3-2S12N FALCON 4-2S12N FALCON 3-3S16N FALCON 4-3S16N
Capacity (m3/h) 240 360
Desander Size (Inch) 10 10
Desander Qty (PCS) 2 3
Desilter Size (Inch) 4 4
Desilter Qty (PCS) 12 16
Working Pressure (Mpa) 0.25~0.4 0.25~0.4
Feeding Size (Inch) 6 6
Output Size (Inch) 8 8
Bottom Shaker Specs
SHAKER MODEL FALCON 3 FALCON 4 FALCON 3 FALCON 4
Vibration Mode Linear Motion
Vibration Motor(Kw) 2x1.72 2 x 1.72
Screen Qty(Pcs) 3 4 3 4
Screen Size x L x H (mm) 585x1165 585 x 1165
Screen Area (m2) 2.05 2.73 2.05 2.73
Adjust G Force ≤7.5G ≤7.5G
Vibration Amplitude (mm) 4.14~5.96 4.14~5.96
Deck Angle Range -1~+5° (Electric & Mechanical)
EX Standard ExdIIBt4
Weight(Kg) 2253 2307 2350 2373
Dimension x L x W x H (mm) 2049 x 2150 x 2147 2676 x 2012 x 2146 2049 x 2086 x 2147 2639 x 2150 x 2147
FALCON 3 AND FALCON 4 SHALE SHAKERS-BASED MUD CLEANER
▪ desander, desilter and high efficiency shale shaker: Three
cleaning steps in one unit for rational use of effective area
▪ hydrocyclons are made of high quality polyurethane
providing long service life
▪ desander (2/10’’ or 3/10’’ cones) with capacity of 1000,
1500 GPM accordingly (240 m3/h and 360 m3/h)
▪ desilter (8,12,16 / 4’’ cones) with capacity of 500, 1000,
1500 GPM accordingly (120 m3/h, 240 m3/h and 360 m3/h)
▪ proprietary shaker deck angle adjustable on-line control
mechanism. Adjustment range between -1°and 5°.
▪ electrical components by SIEMENS, SCHNEIDER
▪ heat treatment of complete shale shaker deck enables
longer service life
MUD CLEANER FALCON 3
MUD CLEANER FALCON 4
DESANDER SN
DESILTER DSL
MODEL SN 2 SN 3
Desander 10” cones 2 3
Max. processing capacity: Density ≤ 1.2 g/ cm3 Viscosity ≤ 45 c 1000 GPM 1000 GPM
Dimensions (mm) LxWxH 2177x1000x1901 2177x1000x190
Total weight (kg) 489 559
MODEL SL 12 SL 16
Desilter 4” cones 12/4’’ cones 16/4’’ cones
Max. processing capacity: Density ≤ 1.2 g/cm3 Viscosity ≤ 45 c 1000 GPM 1500 GPM
Dimensions (mm) LxWxH 2193x900x1511 2193x900x151
Total weight 504 539
10 11
SHALE SHAKER SCREENSDECANTER CENTRIFUGE AKR
SHALE SHAKER SCREENS DECANTER CENTRIFUGE AKR
AKROS applies the most advanced technologies manufacturing various screen panels designed for shale shakers with
mesh sizes from API 20 to API 400. We also offer screen panels for all models of the screen shakers manufactured by
Brandt, Derrick, M-I SWACO, KEMTRON etc. AKROS can fabricate customized screen panels, with sizes and specifications
as requested by clients.
Four-sided tension of the screen plates is used during fabrication of the screen panels. The screen plates can be fabricated
with both square and rectangle mesh shapes. Plugs for isolation of the ruptured mesh areas can be used to extend service
life.
Screen panels 20-50 API have a double layer design, screen panels 60-325 API have a triple layer design. The first layer of
the screen panel plate is made of SS304 grade steel, the second and the third layers of the screen panel plates are made of
SS316L grade steel.
Framed screen panels – the frame is made of composite materials resistant to corrosive drilling muds. Storage life of screen
panels with composite frame is over 5 years. Composite frame screen panels have an effective area 10-20% larger than metal
framed screen panels.High quality fiber glass is used to improve temperature rating of the composite material, the composite
frame maintains it s properties under temperature of up to140 degrees Celsius.
AKROS offers high efficiency AKR-series centrifuge of different configurations that are designed for high efficiency
separation of solids, barite recovery during drilling. It can also be combined with flocculation and coagulation unit during
dehydration.
High efficiency centrifuges AKR-453, AKR-553 are designed specifically for processing of large volumes of drilling mud.
SH
AL
E S
HA
KE
R S
CR
EE
NS
DE
CAN
TER
CE
NTR
IFU
GE
AK
R
MODEL AKR - 363 AKR - 452 AKR - 453 AKR - 553
Bowl Diameter (mm) 360 (14’’) 450 (18’’) 450 (18’’) 550 (22’’)
Bowl Length (mm) 1271 (50’’) 1105 (43’’) 1540 (61’’) 1800 (71’’)
Max Capacity (m3/h) 45 57 80 114
Effective Capacity (m3/h) 30 40 60 90
Max Bowl Speed (RPM) 3900 1800 3200 3000
Typical Bowl Speed (RPM) 3200 1800 2800 2500
Max G Force 3063 815 2578 2719
Typical G Force 2062 815 1973 1888
Cut Point(Microns) 2~5 5~7 2~5 2~5
Differential Speed (RPM) 38 32 45 45
Gearbox Torch (N.M) 3500 3500 7500 12000
Gearbox Ratio 57:1 57:1 57:1 35:1
Main Motor (Kw) 37 (50 HP) 45 (60 HP) 55 (75 HP) 90 (120 HP)
Back Drive Motor (Kw) 11 (15 HP) - 22 (30 HP) 37 (50 HP)
Recommend Pump (Kw) 7.5 (10 HP) 11 (15 HP) 15 (20 HP) 22 (30 HP)
EX Standard ExdIIBt4
Electric Cabinet Exd Standard / PLC with positive pressure
Weight (kg) 3500 3410 4580 5840
Dimension: L x W x H (mm) 3305 x 1638 x 1277 2939 x 1748 x 1320 3824 x 1798 x 1317 4293 x 1978 x 1381
№ API “Separation (micron)”
“Part number FALCON”
“Part number MONGOOSE”
“Part number ALS”
“Part number Brandt Cobra”
“Part number FLC-48 (2000)”
“Part number FLC-500”
API 25 от 655.0 до 780.0 AK-024-FAL AK-024-MON AK-024-SWA AK-024-BHX AK-024-D48 AK-024-D50
API 35 от 462.5 до 550.0 AK-038-FAL AK-038-MON AK-038-SWA AK-038-BHX AK-038-D48 AK-038-D50
API 40 от 390.0 до 462.5 AK-045-FAL AK-045-MON AK-045-SWA AK-045-BHX AK-045-D48 AK-045-D50
API 50 от 275.0 до 327.5 AK-050-FAL AK-050-MON AK-050-SWA AK-050-BHX AK-050-D48 AK-050-D50
API 60 от 231.0 до 275.5 AK-084-FAL AK-084-MON AK-084-SWA AK-084-BHX AK-084-D48 AK-084-D50
API 70 от 196.0 до 231.0 AK-105-FAL AK-105-MON AK-105-SWA AK-105-BHX AK-105-D48 AK-105-D50
API 80 от 165.0 до 196.0 AK-120-FAL AK-120-MON AK-120-SWA AK-120-BHX AK-120-D48 AK-120-D50
API 100 от 137.5 до 165.0 AK-165-FAL AK-165-MON AK-165-SWA AK-165-BHX AK-165-D48 AK-165-D50
API 120 от 116.5 до 137.5 AK-200-FAL AK-200-MON AK-200-SWA AK-200-BHX AK-200-D48 AK-200-D50
API 140 от 98.0 до 116.5 AK-230-FAL AK-230-MON AK-230-SWA AK-230-BHX AK-230-D48 AK-230-D50
API 170 от 82.5 до 98.0 AK-270-FAL AK-270-MON AK-270-SWA AK-270-BHX AK-270-D48 AK-270-D50
API 200 от 69.0 до 82.5 AK-325-FAL AK-325-MON AK-325-SWA AK-325-BHX AK-325-D48 AK-325-D50
API 230 от 58.0 до 69.0 AK-350-FAL AK-350-MON AK-350-SWA AK-350-BHX AK-350-D48 AK-350-D50
API 270 от 49.0 до 58.0 AK-370-FAL AK-370-MON AK-370-SWA AK-370-BHX AK-370-D48 AK-370-D50
API 325 от 41.5 до 49.0 AK-400-FAL AK-400-MON AK-400-SWA AK-400-BHX AK-400-D48 AK-400-D50
12 13
CENTRIFUGE CONTROL PANEL WITH VARIABLE FREQUENCY DRIVE (VFD)
FEATURES & BENEFITS
AKR – 363
Variable frequency drive supplied with centrifuge allows to
set required parameters and conduct monitoring within
required range according to drilling conditions:
▪ bowl rotation speed
▪ differential speed
▪ feeding pump capacity
Automatic control and regulation are conducted via
programmable logical controller with sensor display which
enables regulation of centrifuge operation parameters
according to changing conditions of drilling.
Variable frequency drive is manufactured by the world
leading manufacturers ABB and Siemens.
▪ parent design with the highest configuration and best material for long and reliable service
▪ bowl cylindrical and conical section made from duplex stainless steel 2205 by centrifugal casting
▪ other parts of the bowl assembly material: stainless steel ss316l
▪ screw protection: tungsten carbide tiles for longer life and easier replacement
▪ screw flow distribution port and bowl solids discharge port protected by tungsten carbide alloy
▪ easily adjustable liquid discharge weir height for flexible application
▪ bowl assembly supported by tighten belt for protection of bearing in moving
▪ pressurized EX Proof VFD control cabinet with PLC controlled
▪ genuine SKF bearing for longer and reliable operation
CUTTINGS DRYER G-PRO 930
AKROS OFFERS CUTTING DRYERS OF THE FOLLOWING DESIGNS
FEATURES AND ADVANTAGES
▪ cutting dryer installed within central primary purification system
▪ mobile cutting dryer unit
▪ high efficiency liquids/solids separation allows recovery of valuable drill mud, that can be returned into the active
system.
▪ less hazardous class of drill mud
▪ reduction of disposal amounts
▪ high capacity (up to 50 tons per hour) provides efficient processing during on-stream dilling
1. The actual capacity of the unit depends on the solids content, density of the feed and working conditions.
2. The amount of residual hydrocarbons in the final product depends on different factors associated with the specific
drilling conditions.
Capacity1 30-50 tons/hr.
Rotation speed 900 rpm / 1200 rpm
G-Force 420G / 750G
Main engine power 55 kW
Mesh size 0.25/0.35/0.5 mm
Residual hydrocarbons in the final product2 5-15 %
Weight 4200 kg
Dimensions: LxWxH 2650х1720х1630 mm
CU
TTIN
GS
DR
YER
CE
NTR
IFU
GE
CO
NTR
OL
PA
NE
L
14 15
MOBILE CUTTING DRYER UNIT G-PRO 930M
MOBILE CUTTING DRYER UNIT G-PRO 930M
G-PRO 930M
To allow integration of cutting dryer into the process of reduction of drilling waste volumes in limited space conditions of
circulation system in regions with moderately cold and cold climate, our specialists designed a mobile cutting dryer unit.
Mobile unit is a heated module which incorporates:
▪ cutting dryer
▪ tank with mixers
▪ washing and recirculating pumps
▪ discharge screw conveyor
▪ ventilation, lighting systems
▪ operator workstation with central
HO
PP
ER
/ M
UD
GU
N
MO
BILE
CU
TTIN
GS D
RYER
HOPPER
HOPPER
MUD GUN
ADVANTAGES AND FEATURES
AKR 45
AKROS offers AKR series mud hoppers, designed and manufactured to enable rapid and efficient dosing and mixing of chemical and additives while preparing and maintaining drilling fluids. The hopper function is based on the venturi effect, when the pressure of a flowing fluid decreases passing through a restriction, thus allowing to add appropriate dozes of polymers, barite, bentonite and other powder additives.
The hopper may be place on the skid with the centrifugal pump, thus simplifying the installation of mud cleaning equipment on the drilling rig.
Mud gun is a low pressure jet mud mixer designed for hydraulic mixing of the drilling mud. Mud guns are installed on the
mud tanks.
▪ rotating mechanism permits manual control of the horizontal fluid flow from the jet nozzle between 0° and 360°
▪ the jet nozzles are made of wear-resistant material
▪ specially designed nozzles inject the fluid in three directions simultaneously
MODEL Pressure (MPa) Hopper Volume (litre) Inlet (inches) Weight (kg) Dimensions LxWxH
AKR 35 0.25 ~ 0.4 35 DN150 174 1100x680x949
AKR 45 0.25 ~ 0.4 45 DN150 174 1100x680x949
MODEL AKR-50X AKR-80X
Working pressure (mPa) ≤6.4
Ratio (deg.) 360o
Number of jet nozzles 3
Mud gun diameter (inches) 2 3
Connection dimensions G2’’ G3’’
16 17
MUD MIXER
MUD MIXER
Mechanical mud mixers are designed to prepare the drilling muds and maintain their required characteristics. They
facilitate uniform mixing of the mud and additives preventing local overtreatment with chemicals. Among other things,
mud mixers keep the weighting material in suspension and minimize the settling of sludge.
▪ high power motor, 3 to 22 KW
▪ wide range of blade sizes
▪ double-row blade mixers can be supplied as an option
MODEL Motor (Kw) Speed (Rpm) Impeller (mm) Explosion protection
Weight (kg) Dimensions
AKR-030M 3 60 650 ExdIIBT4 154 717х560х472
AKR-055M 5.5 60 850 ExdIIBT4 280 892х700х600
AKR-075M 7.5 60 950 ExdIIBT4 287 980х750х608
AKR-110M 11 60 1050 ExdIIBT4 402 1130х840х655
AKR-150M 15 60 1100 ExdIIBT4 423 1158х840х655
AKR-185M 18.5 60 1050 ExdIIBT4 746 1270х1000х730
AKR-220M 22 60 1100 ExdIIBT4 820 1270х1000х730
VACUUM DEGASSER
VACUUM DEGASSER
AKR series vacuum degassers are able to service the needs of any application.
It is usually installed after the shakers. Each degasser effectively and efficiently removes gases from gas-cut mud, thus
ensuring that the proper mud weight is pumped down hole. In doing so, the degassers are able to aid in the prevention of
potential blowouts.
Unlike the traditional vacuum degasser, AKR vacuum degasser is a self-contained unit, AKR vacuum degasser is
monitored by level sensor to protect over suction of the flids. The gas-cut mud is drawn into the degasser by a vacuum
created by a regenerative vacuum without needing centrifugal pump.
AKR 270 degasser can act as a big agitator for the drilling mud, which helps the treatment for desander and desilter.
VACU
UM
DEG
ASSE
R
MU
D M
IXER
MODEL AKR 270 AKR 360
Tank Diameter (mm) 920 920
Capacity(m3/h) ≤270 ≤360
Vacuum Degree(Mpa) -0.02~-0.04
Handling Effiiency ≥95%
Main Motor Power(Kw) 22 37
Pump Motor Power(Kw) 7.5 7.5
Rotation Speed(RPM) 700 860
Ex Standard ExdIIBt4
Suction Line Size DN150
Output size DN200
Weight(Kg) 1780 1815
Dimension x L x W x H(mm) 2100 x 1605 x 1729 2100 x 1605 x 1729
18 19
CENTRIFUGAL DEGASSER
CENTRIFUGAL DEGASSER
WORKING PRINCIPLES
Centrigugal degasser is a new type degasser, specialized in processing gas cut drilling fluids. Normally it is installed
after shale shaker and widely used in various solids control systems, and it is very important for recovering mud weight,
stabilize mud viscosity performance, reduce drilling cost. Meantime it can be used as a big power blender. Its advantages
are large capacity, high rate of degassing, less area required, low energy consumption, easy operation and maintenance.
Via the rotating impeller, the degasser sucks the drilling fluid into the vessel. The fluids will stay at a level higher than the
gas cut drilling fluid and then a cylindrical liquid layer with inverted cone shape space in the middle will be formed. Drilling
fluid is discharged from discharge port along a tangent line.
With the impeller rotating, bubble breaks, gas will be extracted from liquid, and finally accumulate in the cone shape space
as the lower density. Pressurizing unit (similar to exhaust fan) will suck air through the narrow channel between the air
distribution disk and air separation ring into the discharge cone, and then gas manifold, braided hose and pressuring unit,
finally discharge the gas out through pressuring device with pressure.
SCRE
W P
UM
P
CEN
TRIF
UGA
L DE
GASS
ER
MODEL AKR
Liquid Inlet Size 20 ‘’
Liquid Outlet Size 8 ‘’
Gas Outlet Size 2 ‘’
Max Liquid Throughput 300 m3/h
Max Gas Removed 30 m3/h
Main motor 22 Kw
Fan Motor 1,1 Kw
Gearbox Ratio 1:3,78
Weight 1375 kg
Dimensions 1150 x 1055 x 2885mm
SCREW PUMP
SCREW PUMP
AKR 30
The AKR series screw pump is a single screw pump. The pump is an ideal pump for feeding to decanter centrifuge without
shearing or agitating the drilling mud. The main parts are screw shaft (rotor) and screw shaft bushing (stator). Because of
the special geometry shape of the two parts, they form pressurize capacity separately. The fluids flow along with the shaft,
inner flow speed is slow, capacity remains, pressure is steady, so it will not generate vortex and agitating.
The shaft of the pump is made from stainless steel, AKR series pump is available for option with complete stainless steel
body, it can drive by coupler, or adjust the speed by using variable speed motor, Triangle V-belt, gear box, etc.
AKR series screw pump is with less accessories, compact structure, small volume, easy maintenance, rotor and stator
are wear parts of this pump, it is convenient to replace.
The stator is made of elastomeric material, so it has particular advantages than other pump to transfer the fluids. With
high viscosity and hard suspended particles included.
MODEL Flow (M3/h)
Pressure (Mpa)
Motor (Kw)
Max Speed (RPM)
Inlet Outlet (Inch) (Inch)
Ex Standard Weight(Kg) DimensionLxWxH(mm)
AKR 10 10 0.3 4 244 DN80 EXdIIBt4 245 2245x320x550
AKR 20 20 0.3 5.5 210 DN80 323 2450x340x562
AKR 30 30 0.3 7.5 258 DN100 386 2761x370x600
AKR 40 40 0.3 11 252 DN125 454 3270x370x665
AKR 50 50 0.3 11 273 DN125 608 3790x400x782
AKR 60 60 0.3 15 225 DN125 649 3322z550x740
AKR 70 70 0.3 22 230 DN150 875 3740x420x785
AKR 80 80 0.3 22 283 DN150 875 3740x420x785
AKR 90 90 0.3 22 205 DN150 875 3740x420x785
20 21
CENTRIFUGAL PUMP
CEN
TRIF
UGA
L PU
MP
SCREW CONVEYOR
SCREW CONVEYOR
Screw conveyor is designed for transportation of solid drill cuttings in the horizontal and tilted plane
▪ pre-fabricated sectional design (12 ft long sections) allows assembling any configuration
▪ the screw is made of wear-resistant material which increases its service life
▪ the conveyors are designed and built to the highest safety standards
▪ protective cover or grating prevents the debris and loose objects from entering the screw system
Note: The capacity is rated for horizontal installation and 1:1 specific gravity.
SCRE
W C
ON
VEYO
R
MODEL Screw Diameter (inches)
Screw Length (ft)
Capacity (tons/hour)
Motor (Kw)
Speed (Rpm)
Explosion protection
Weight (kg)
Dimensions (mm)
AKR12A-24 12 24 20 5.5 60 ExdIIBT4 1426 9150х450х600
AKR12A-36 12 36 20 7.5 60 1855 12950х450х600
AKR12A-48 12 48 20 11 60 2318 16750х450х600
AKR14A-24 14 24 30 7.5 60 1515 9200х485х650
AKR14A-36 14 36 30 11 60 2028 13000х485х650
AKR14A-48 14 48 30 15 60 2549 16800х485х650
AKR16A-24 16 24 45 11 60 1668 9200х545х680
AKR16A-36 16 36 45 15 60 2269 13050х545х680
AKR16A-48 16 48 45 18.5 60 3344 16950х545х680
CEN
TRIF
UGA
L PU
MP
CENTRIFUGAL PUMP
AKR 8х6х13
AKR series centrifugal pump is used for transferring drilling mud. It can be used as feeding pump for desander, desilter,
or used as mixing pump for Jet Mud Mixer. Also it can be used as trip pump,and supercharging pump for rig mud pump.
All AKROS model centrifugal pump use tungsten carbide mechanical seal, with famous brand Bearing. And spare parts
interchangeable with most of the international Brand pump which helps customer to source spare parts easily. Open
impeller design that lowers axial thrust loads, and make it easier for installation, repair and maintenance.
MODEL Flow (m3/h)
Lift(M)
Motor (Kw) Speed(RPM)
Impeller (Inch)
EX Standard Weight (kg) Dimension (LxWxH (mm)
AKR 8x6x14 320 35 75(100HP) 1450 14 EXdIIDt4 1096 1968x650x1017
AKR 8x6x13 272 35 55 (75HP) 1450 13 987 1894х650х957
AKR 6x5x14 234 35 55 (75HP) 1450 14 801 1867х534х957
AKR 6x5x13 200 35 45(60HP) 1450 13 786 1811x558x858
AKR 6x5x12 150 30 37(50HP) 1450 12 771 1786x558x858
AKR 5x4x13 120 35 30(40HP) 1450 13 696 1696x568x805
AKR 5x4x12 90 30 22(30HP) 1450 12 583 1648x568x800
AKR 4x3x13 65 35 18.5(25HP) 1450 13 561 1595x505x800
AKR 4x3x12 552 28 15(20HP) 1450 12 482 1550x505x755
AKR 4x3x11 45 25 11(15HP) 1450 11 464 1510x505x755
22 23
CUTT
INGS
RE-
INJE
CTIO
N
ENVIRONMENTAL SOLUTIONS
CUTTINGS RE-INJECTION
CUTT
INGS
RE-
INJE
CTIO
N
WHAT IS THE CRI?
Cuttings re-injection is an economically sound and environmentally friendly long-term solution for cuttings disposal in
remote areas. The available field-proven practices allow to minimize costs and HC emissions typical for the other drilling
wastes disposal methods. Also this method excludes any other current or future liabilities related to the cuttings disposal.
It is a waste disposal technique where cuttings and other oilfield wastes (such as mud slurry, old drilling fluids, waste water
from the rig) are mixed into a slurry with water and pumped at high pressure into hydraulically created fractures below the
surface for safe disposal of such wastes.
SAFETY AND QUALITY ASSURANCE
The safety and quality assurance process applied for the CRI purposes provides an integral approach to all aspects of the
CRI project. Based on the analysis of the data provided by the Client our specialists design special solutions which are
fully optimized for each particular project. Our CRI quality assurance and safety program is a unique product in oil and gas
industry as it allows verification of quality parameters before, during and after re-injection. This program enhances the
safety of the project, including its economical profitability.
SLURRIFICATION UNIT
FUNCTION
The unit is an integral part of the drilling waste injection system; it is designed to process different types of wastes and to
convert them into slurry for further containment before injecting the slurry into formation. This unit has a small footprint and
it can be installed in a relatively small area. A conventional standard slurrification unit consists of the following components:
▪ coarse tank, 55 barrels
▪ fines tank, 55 barrels
▪ two holding tanks, 100 barrels each
▪ hydration tank, 55 barrels
OPERATING PRINCIPLE
Drilling wastes are first collected into the coarse tank where they are diluted with process water and / or liquid wastes.
At the same time the large particles are broken down in the continuous circulation process activated by centrifugal
pumps and power-driven agitators. There is an operator’s station on the top of the tank; it is equipped with the control
panels to control the slurrification process.
The drilling wastes are then directed to the shale shakers installed on the holding tanks. Liquid wastes and solid particles
(<300 micron) are collected in the holding tanks, while the large particles, separated by the shale shaker, are directed
to the blender installed on the top of the fines tank. Treated wastes are disintegrated in the fines tank by continuous
circulation process, and then the material is fed into the shale shakers.
The dehydration tank is designed to improve the rheology of the slurry by adding chemicals through the hopper installed
on this tank.
When the appropriate parameters have been reached, the slurry is directed to the HP pump for further injection into
formation.
The total power consumption of the unit is 510 kW, the capacity is 240 m3/day.
Note* - the capacity of the unit may vary as it depends on the type of drilled rocks and on the amounts of sand.
SOLUTIONS
Cuttings re-injection back into formation is an ideal solution, which complies with the requirements applied to drilling and
well production operations in the Russian Federation. Our field-proven experience allows to offer a cuttings re-injection
package, which will benefit the waste disposal process in the most complicated work conditions by providing efficiency and
economic parameters satisfying all appropriate requirements of the environmental legislation.
ECONOMICS
Storage and transport practices used for further treatment and disposal of wastes present additional challenges, that can
be extremely costly for each project. Transportation of wastes is often impossible due to the poor weather conditions. In
some cases, such restrictions may seriously affect the project and make it non-profitable. The cuttings re-injection system
has been thoroughly developed and designed to settle such problems by treating cuttings on the rig or in adjacent areas thus
reducing or excluding the necessity to transport cuttings from the rig or to truck them to distant locations. This approach
gives an opportunity to the development of new oilfields which were inaccessible due to the lack of road infrastructure.
ENVIRONMENTAL
Cuttings re-injection method is a solution which fully complies with the requirements of the Russian Law. In addition to
compliance with environmental regulations and zero-discharge polices it ideally fits for environmentally sensitive areas,
requiring serious restrictions for HC emissions versus any other waste disposal methods and technologies.
24 25
CUTTINGS DRYER
FUNCTION
A cutting dryer can reduce total oil-based mud losses thus
decreasing the volume of cuttings, while drilling wells using
an oil-based drilling fluids.
APPLICATIONS
Offshore and onshore projects where the recovery of valuable
drilling fluid from cuttings, as well as recovery of oil-based
mud and return to the active system are the priorities.
PROBLEMS
More stringent cuttings-discharge regulations have
pressured operators and drilling contractors to reduce
drilling waste volumes and recover premium products for
reuse.
SOLUTIONS
The cuttings dryer features a state-of-the-art design that
can process varying amounts of cuttings and fluids, typically
up to 60 tons per hour. Dry solids discharged from the dryer
are typically <5-6% oil content.
ECONOMICS
The cuttings dryer improves overall cost-efficiency, producing
reduced amounts of extremely dry cuttings for disposal and
recovering valuable fluid for reuse. It is effective with oil- and
synthetic-base drilling fluids.
ENVIRONMENTAL
The dryer minimizes waste volumes , dramatically reducing
disposal costs. In the quest for improved environmental
practices, operators need solid-control solutions that take
liquids / solids separation to a new level. The cuttings drier
incorporates a high-speed vertical centrifuge, that achieves
maximum liquids / solids separation in large-volume
processing. This gives operators a critical advantage in
meeting increasingly stringent environmental rules for
cuttings disposal.
DEW
ATER
ING
CUTT
INGS
DRY
ER
DEWATERING
FLOCCULATION AND COAGULATION UNIT
Flocculation and coagulation unit is made on the basis of 40 ft standard container that allows to easily transport this
equipment by land and sea transport carriers.
CONTAINER-TYPE UNIT CONSISTS OF TWO COMPARTMENTS
▪ the first compartment – chemical agents dosing unit
▪ the second compartment – mud laboratory with common monitoring and control system
Dehumidification unit is the part of the circulation system for drilling mud treatment and include centrifuge for water
removal. As well as tanks for water storage.
CONTAINER SPECIFICATIONS
▪ overall dimensions comply with the parameters of 40 ft standard container
▪ front doors and emergency exits in the laboratory and chemical agents dosing compartments
▪ the partitions are made of corrugated metal
▪ internal walls and roof are completely isolated
▪ heating and air conditioning system can be supplied as an option
▪ all our specifications (TU) for performing repair welding operations and welding procedures qualification records
were certified by the international experts (Lloyd’s Register (LR) / Det Norske Veritas (DNV))
CHEMICAL AGENTS DOSING UNIT
▪ total capacity of tanks for liquids storage is 50 m3
▪ tanks for mixture making are made of stainless steel of SS 304 grade
▪ at least one mixer (or more) is provided in each tank/tank section
▪ access manholes are provided in each tank/tank section for performing internal work
▪ inspection holes are also provided for visual inspection of contaminated / clean water prior to pumping to the storage tanks
▪ centrifugal-type pumps for water pumping
▪ all the passages have antiskid coating of glass fiber with metal base
▪ distribution panel for power supply to the mixers, motors, pumps and lighting
▪ process piping (stainless steel of SS 304 grade) and manually operated control valves
26 27
CUTTINGS SKIPS
THER
MAL
DES
ORP
TIO
N S
YSTE
M
Cuttings skips are designed for containment and transfer of drilled rocks and other wastes produced from well drilling.
The design of cuttings skips provides heavy-duty durability and reliability, that’s why cuttings skips are widely used in
offshore drilling, where the most stringent requirements are applied.Due to portability of equipment and for stacking
convenience, drill cuttings collected in skips may be shipped by water transport, as well as by road and railway transport.
The cuttings skips may be used under extreme temperatures from minus 40°C to plus 50°C without deterioration of
strength and sealing properties.
Max gross weight 11000 kg
Crate 1 600 kg
Max net weight 9 400 kg
Net volume 3.8 m3
Length 2212mm
Width 1852 mm
Height 1600 mm
CUTT
INGS
SKI
PS
DIMENSIONS AND WEIGHT
THERMAL DESORPTION SYSTEM
THERMAL DESORPTION SYSTEM CUTTINGS SKIPS
THE TECHNOLOGY IS APPLICABLE BOTH IN ONSHORE AND OFFSHORE ENVIRONMENT
The treatment technology is based on the thermal processes resulting in evaporation of liquids from drilling cuttings,
including: hydrocarbons and water. Water evaporates first, turning into water vapour, and hydrocarbons evaporate later,
as they have a higher boiling point. Hydrocarbons are separated from water during the two stage condensation process,
based on the same principles.
The hammer mill generates large quantities of heat during the grinding process, thus breaking cuttings and removing
liquids, including pore fluids. The design provides reduction of thermal energy to minimum and simultaneous removal of
liquid components with recovery of hydrocarbons for further re-use in oil-based drilling fluids.
AKROS offers thermal desorption equipment in the following configurations:
▪ fixed unit (TCC 46E)
▪ modular / mobile unit
ADVANTAGES
▪ it removes 99% of solids
▪ it is environmentally friendly
▪ it entails no direct combustion
▪ recovery of oil or synthetic-based drilling fluids and water
▪ the quality of recovered base oil is comparable with the original base oil and is suitable for re-use
▪ safe and reliable operation
▪ operating flexibility: short start-up and shut-down time
▪ compact size
▪ flexible design solution
MODEL TCC12E-M TCC23E-M TCC43E-M TCC46E
Capacity, t/h 1-2 2-3 4-6 4-6
Electromotor power, Kw 250 500 1000 1000