Epson Stylus Photo 1400 Housing Replacement · Epson Stylus Photo 1400 Housing Replacement This...

8
Epson Stylus Photo 1400 Housing Replacement This guides the user in removing the bottom, side and top housings of the printer. Scritto Da: Larry Huang Epson Stylus Photo 1400 Housing Replacement Bozza: 2016-05-26 ID Guida: 7065 - © iFixit — CC BY-NC-SA it.iFixit.com Pagina 1 di 8

Transcript of Epson Stylus Photo 1400 Housing Replacement · Epson Stylus Photo 1400 Housing Replacement This...

Epson Stylus Photo 1400 HousingReplacement

This guides the user in removing the bottom, side and top housings of the printer.

Scritto Da: Larry Huang

Epson Stylus Photo 1400 Housing Replacement Bozza: 2016-05-26ID Guida: 7065 -

© iFixit — CC BY-NC-SA it.iFixit.com Pagina 1 di 8

INTRODUZIONE

To get to the inside parts of the printer, the housing components must come off.

STRUMENTI:Flathead Screwdriver (1)Phillips #2 Screwdriver (1)iFixit Opening Tools (1)

Epson Stylus Photo 1400 Housing Replacement Bozza: 2016-05-26ID Guida: 7065 -

© iFixit — CC BY-NC-SA it.iFixit.com Pagina 2 di 8

Passo 1 — Housing

Turn off the printer.

Disconnect all data connectionscoming into the printer such as USB,networkd cables, firewire, etc. aswell as removing the power cord.

Passo 2

Locate the IEEE cover in the back.

Gently slide cover to the right to unlatch then pull to remove it.

Epson Stylus Photo 1400 Housing Replacement Bozza: 2016-05-26ID Guida: 7065 -

© iFixit — CC BY-NC-SA it.iFixit.com Pagina 3 di 8

Passo 3

Using a #2 Phillips screwdriver, remove the four 10mm screws shown.

Remove the 6mm screw that holds the rear housing in place.

Passo 4

Remove the rear housing by pulling it backwards.

Epson Stylus Photo 1400 Housing Replacement Bozza: 2016-05-26ID Guida: 7065 -

© iFixit — CC BY-NC-SA it.iFixit.com Pagina 4 di 8

Passo 5

Insert the flathead screwdriver or plastic pry tool into the cutouts of the lower housing.

Release the two tabs of the side housing by lifting the tool in an upward motion

Remove the side housing by pulling it outwards.

Passo 6

Both side housings are attached by the same type of mechanism.

Using the same method, remove the other side housing.

Epson Stylus Photo 1400 Housing Replacement Bozza: 2016-05-26ID Guida: 7065 -

© iFixit — CC BY-NC-SA it.iFixit.com Pagina 5 di 8

Passo 7

Lift the paper support.

Open the printer cover and front cover.

Passo 8

Remove the four 10 mm Phillips #2 screws from the sides of the printer.

Remove the three 6mm Phillips #2 screws.

Epson Stylus Photo 1400 Housing Replacement Bozza: 2016-05-26ID Guida: 7065 -

© iFixit — CC BY-NC-SA it.iFixit.com Pagina 6 di 8

Passo 9

Detach the tabs from the pins on each side by pulling it outwards.

Passo 10

Remove the two 10 mm Phillips #2 screws on the front of the printer.

Epson Stylus Photo 1400 Housing Replacement Bozza: 2016-05-26ID Guida: 7065 -

© iFixit — CC BY-NC-SA it.iFixit.com Pagina 7 di 8

To reassemble your device, follow these instructions in reverse order.

Questo documento è stato generato l'ultima volta su 2019-07-10 08:14:29 PM.

Passo 11

Disconnect the cable on the side by carefully pulling it outwards.

You may need to gently rock the cable up and down while pulling.

Passo 12

Remove the upper housing by lifting it upwards.

It's easier to lift the housing by gripping it from the bottom.

Epson Stylus Photo 1400 Housing Replacement Bozza: 2016-05-26ID Guida: 7065 -

© iFixit — CC BY-NC-SA it.iFixit.com Pagina 8 di 8