Environmentally and chemically resistant. Multi-directional ... - RAB€¦ · SPS expansion joint...

Environmentally and chemically resistant.Multi-directional capabilities.Easy install.Wabo®SPS preformed silicone joint sealing system

Preservation in the Fast Lane.

wbacorp.com

Features and BenefitsFar beyond your typical silicone seal.

FEATURES BENEFITS

Silicone Profile and Adhesive

Components bond with virtually no degradation over decades of weather exposure

0 to 4 inch Movement

Range

Accommodates non-uniform deck joint openings and movements

Environmentally and

Chemically Resistant

Chemically inert and unaffected by exposure, ultraviolet light, weather or extreme temperatures -55°F (-48°C) to 400°F (204°C)

Simplicity of Installation

Allows for quick joint repairs, short traffic closures and provides a wide array of joint placement widths

Performance Adhesive

Properties

Primerless adhesion to adjacent surfaces and capacity to absorb high deformations provides assurance of watertightness

Low VOC

Exceeds the U.S. Green Building Council’s Leadership in Energy and Environmental Design (L.E.E.D.) requirements

Wabo®SPS SystemPreformed silicone joint sealing system

Due to the durability, low stress design, and versatility, the Wabo®SPS system results in a quick turn-around solution for sealing deck Expansion Joints.

wbacorp.com1-800-677-4922

Wabo®SPS SystemRecommended applications. • Sealing bridge deck expansion joints • Retrofitting expansion joints requiring minimum downtime

• Expansion joint applications with varying joint widths and movements ranging up to 4 inches

The Wabo®SPS expansion joint system is a preformed silicone sealing system designed to accommodate movements and varying joint widths on bridges, piers, or other civil structures requiring watertight sealing of horizontal expansion joints. The preformed silicone seal is bonded in place with a high performance, dual-purpose silicone sealant and adhesive that adheres to concrete, steel, elastomeric and viscoelastic concrete joint substrates without the need of a primer. Boasting a low stress design, the SPS system operates well in a variety of environments while retaining its flexibility. Ideally suited for both new construction and retrofitting of existing expansion joints, the Wabo®SPS system is a durable and quick turn around solution for sealing deck expansion joints.

Wabo®SPS 225 Wabo®SPS 400

For Best ResultsTips to do it right. • Repair any spalls, voids, or structural cracking at the joint interface • Do NOT allow any of the components to freeze prior to installation Store all components out of direct sunlight in a clean, dry location between 50˚F (10˚C) and 90˚F (32˚C). Do not store in high humidity

• Shelf life of chemical components is approximately 12 months • Do NOT install when surface temperature are less than 40˚F (4˚C) • Periodically inspect the applied material and repair localized areas as needed. Consult a Watson Bowman Acme representative for additional information

• Make certain the most current version of the product data sheet is being used. Please consult our website (www.wbacorp.com) or contact a customer service representative at [email protected]


MODEL NO.

RECOM-MENDED MINIMUM INSTALL WIDTH

MINIMUM JOINT

OPENING “A”

MAXIMUM JOINT

OPENING “A”

MINIMUM GROOVE INSTALL DEPTH

“B”

MOVEMENT RATING

(MR)

in mm in mm in mm in mm in mm

SPS-225 1.25 31.75 0.75 19.05 3.00 76.20 2.625 66.67 2.25 57.15

SPS-400 2.00 50.80 1.00 25.40 5.00 127.0 3.75 95.25 4.00 101.60

Note: All measurements have been converted from metric and rounded to the nearest 1/8”.

Technical Data

Preformed Silicone Seal Profile:Wabo®SPS silicone seal is manufactured from a custom extrusion grade organic silicone compound and is highly resistant to the effects of ultra violet rays and ozone. The seal has an operating temperature range of -55°F (48°C) to 400°F (204°C), and meets the following physical properties:

PHYSICAL PROPERTY TEST METHOD REQUIREMENTS

Color Visual Gray

Durometer (Shore A) ASTM D 2240 55 +/- 5

Tensile Strength ASTM D 412 1000 psi, min

Elongation @ break ASTM D 412 400% min

Tear Resistance (die B) ASTM D 624 100 lbs/in min

Compression Set @ 212°F, 70 hrs ASTM D 395 30% max

Silicone Adhesive:Wabo®Sil Adhesive is a one-part, non sag, high strength silicone adhesive that ensures a water tight system by providing a tenacious bond to the silicone profile and most bridge construction adjacent surfaces.

PHYSICAL PROPERTY TEST METHOD REQUIREMENTS

Color Visual Gray

Durometer (Shore A) ASTM D 2240 25 +/- 5

Elongation ASTM D 412 700% min

Tensile at 100% Elongation ASTM C 1184 70 psi, min

Peel Adhesion to substrates ASTM C 794 55 lbs/in min

Work Life (tool time) 20-30 minutes

Wabo®Sil Adhesive:

Wabo®SPS Profile:

Watson Bowman Acme Corp. | 95 Pineview Drive Amherst, NY 14228 | (p) 800-677-4922 (f) 716-691-9239 | wbacorp.com

Wabo®SPS Preformed Silicone Joint Sealing SystemDesigned for the preservation and maintenance of bridge expansion joints

FEATURES BENEFITS

Silicone Profile and Adhesive

Components bond with virtually no degradation over decades of weather exposure

0 to 4 inch Movement

Range

Accommodates non-uniform deck joint openings and movements

Environmentally and

Chemically Resistant

Chemically inert and unaffected by exposure, ultraviolet light, weather or extreme temperatures -55°F (-48°C) to 400°F (204°C)

Simplicity of Installation

Allows for quick joint repairs, short traffic closures and provides a wide array of joint placement widths

Performance Adhesive

Properties

Primerless adhesion to adjacent surfaces and capacity to absorb high deformations provides assurance of watertightness

Low VOC

Exceeds the U.S. Green Building Council’s Leadership in Energy and Environmental Design (LEED) requirements

PRODUCT DATA SHEET rev. 9.2014

Wabo®SPS silicone seal is manufactured of a custom extrusion grade organic silicone compound and is highly resistant to the effects of ultra violet rays and ozone. The seal has an operating temperature range of -55°F (-48°C) to 400°F (204°C), and meets the following physical properties (below):

SPS TECHNICAL DATA:

DESIGN INFORMATION:

Wabo®SPS Profile

PHYSICAL PROPERTY ASTM TEST METHOD REQUIREMENT

Color Visual Gray

Durometer (Shore A) D 2240 55 +/-5

Tensile Strength D 412 1000 PSI/Min

Elongation at Break D 412 400% Min

Tear Resistance (B) D 624 100 Lbs/In Min

Compression Set at 212°F (100°C), 70 hours D 395 30% Max

Wabo®Sil Adhesive


Color Visual Gray


Elongation D 412 700% Min

Tensile at 100% Elongation C 1184 70 PSI, Min

Peel Adhesion to substrates C 794 55 Lbs/In Min

Work Life (tool time) - 20-30 Min

DESCRIPTION:The Wabo®SPS Joint System is a preformed silicone joint sealing system designed to accommodate movements and varying joint widths on bridge decks.

The preformed silicone seal is bonded in place with a high perfor-mance dual-purpose silicone sealant and adhesive that adheres to concrete, steel, elastomeric concrete and viscoelastic concrete joint interface substrates without the need of a primer. A low stress design, the silicone properties of the system are virtually unchanged with time or environment when compared to more commonly used elastomers such as EPDM or polychloroprene.

Ideally suited for both new construction and retrofitting of exist-ing joints, the Wabo®SPS Joint System is a durable, quick, all-encompassing solution for sealing deck joints.

RECOMMENDED FOR: Sealing bridge deck expansion joints Quick joint repairs, short traffic closures Joint applications with varying joint widths Expansion joints requiring movement ratings

up to 4 inchesPACKAGING/COVERAGE: Profile: Wabo®SPS profile seal, custom packaged to

specific lengths Adhesive: Wabo®Sil Adhesive, a one part sealant - 29 oz

cartridge

Wabo®Sil Adhesive (below) is a one-part, non sag, high-strength silicone adhesive.

Wabo®Sil Adhesive Yield Chart

JOINT SYSTEM YIELD/UNIT (29oz. cartridge)

Wabo®SPS-225 9 LF (3.8m)

Wabo®SPS-400 5 LF (2.4)

Wabo®Sil Adhesive is supplied in a single 29oz. cartridge:



pg 2 of 2

APPLICATION:

INSTALLATION SUMMARY:• Newly placed concrete: joint interface must be dry and

clean (free of dirt, coatings, rust, grease, oil, and other contaminants), sound, and durable. New concrete must be cured (14 day minimum).

• Aged concrete: loose, contaminated, weak, spalled, deteriorated and/or delaminated concrete must be removed to sound concrete and repaired prior to placement.

• Steel: steel substrates should be sound, steel surfaces must be abrasive blasted SP-10 near white metal, immediately prior to installation.

• The joint opening must be abrasive blasted to remove all latencies and contaminants which may cause bonding problems. The joint opening should be blown clean using compressed air (>90psi).

• A non-gassing closed-cell expanded polyethylene foam rod, approximately 25% larger in diameter than the joint gap is positioned in the joint opening on the larger seal so not to allow the seal to potentially fall thru the opening during installation.

• Clean all excess material from the edges of the joint opening as soon as possible. DO NOT allow the silicone to cure before

removing it.

• Wabo®Sil will be ready to accept traffic generally within 30 minutes after installation.

• Seal Positioning: A closed cell foam backer rod or foam board is recommended for seal depth positioning if concrete step is not present. Follow manufacturer’s noted Groove Depth “B” on seal chart.

• Preformed Silicone Preparation: Unroll seal and with a clean rag wipe the serrated sidewall and rounded seal lugs with denatured alcohol (supplied by others) to ensure a clean surface for bonding.

• Preformed Silicone Seal Placement: Apply a continuous 3/8” to ½” bead of Wabo®Sil Adhesive to both sides of the joint interface.

• Fold seal and insert into the joint. Release seal and ensure contact with joint interfaces and the adhesive.

• Apply a second bead of adhesive along each side of seal and fill to the top of the serrations. DO NOT apply adhesive above the serrated areas. Tool Wabo®Sil Adhesive on both sides to ensure the adhesive makes full contact with the seal and substrate.

FOR BEST RESULTS:• Repair any spalls, voids, or structural cracking at the joint

interface.• DO NOT allow any of the components to freeze prior to

installation. Store all components out of direct sunlight in a clean, dry location between 50˚F (10˚C) and 90˚F (32˚C). DO NOT store in high humidity.

• Shelf life of chemical components is approximately 12 months.

• DO NOT install when surface or substrate temperature is

less than 40˚F (4˚C)• Periodically inspect the applied material and repair

localized areas as needed. Consult a Watson Bowman Acme representative for additional information.

• Make certain the most current version of the product data sheet is being used. Please consult the website (www.wbacorp.com) or contact a customer service representative.

Related Documents:• Material Safety Data Sheets• Wabo®Sil Adhesive Data Sheet• Wabo®SPS Specification• Wabo®SPS Sales Drawings• Wabo®SPS Installation Procedure

Options/Equipment:• Pneumatic Air Gun (for 29oz cartridges) can be pur-

chased from WBA• Closed cell polyethylene backer rod for larger openings

to hold the seal in position if there is no concrete step

For our most current information, please visit our website

@ wbacorp.com

Wabo®SPS System rev. 9.2014

LIMITED WARRANTY:Watson Bowman Acme Corp. warrants that this product conforms to its current applicable specifications. WATSON BOWMAN ACME CORP. MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR WARRANTY OF FIT-NESS FOR A PARTICULAR PURPOSE. The sole and exclusive remedy of Purchaser for any claim concerning this product, including, but not limited to, claims alleging breach of warranty, negligence, strict liability or otherwise, is the replacement of product or refund of the purchase price, at the sole option of Watson Bowman Acme Corp. Any claims concerning this product shall be submitted in writing within one year of the delivery date of this product to Purchaser and any claims not presented within that period are waived by Purchaser. IN NO EVENT SHALL WATSON BOWMAN ACME CORP. BE LIABLE FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL (INCLUDES LOSS OF PROFITS) OR PUNITIVE DAMAGES. Other warranties may be available when the product is installed by a factory trained installer. Contact your local Watson Bowman Acme representative for details. The data expressed herein is true and accurate to the best of our knowledge at the time published; it is, however, subject to change without notice.©2014 Watson Bowman Acme Corp.

PRODUCT DATA SHEET


SPECIFICATION


PRODUCT INFORMATION

Manufacturer:Watson Bowman Acme Corp95 Pineview DriveAmherst, NY 14228

(p) 800-677-4922(f) 716-691-9239wbacorp.com

Product Name:Wabo®SPS Joint Sealing System

Product Description:The Wabo®SPS Joint Sealing System is an expansion joint system which bonds a preformed silicone seal to concrete, steel, elastomeric concrete or viscoelastic concrete joint interfaces with a silicone adhesive.

Intended Use:To seal expansion joints on bridges

A. GeneralThe work shall consist of furnishing, placing and bonding a pre-formed silicone joint seal with a silicone adhesive to adjacent struc-tures in accordance with the details shown on the plans and the requirements of these specifications. Components of the preformed silicone joint sealing system shall not be substituted and shall be supplied from one expansion joint manufacturer.Expansion Joint Manufacturer shall have a minimum ten (10) years experience specializing in the design and manufacture of silicone technology expansion joint systems.

B. Quality AssuranceExpansion Joint Manufacturer shall be ISO-9001 and RC-14001 certified, and shall provide written confirmation that a formal Quality Management System has been independently audited and approved to these standards. Alternate manufacturers will be considered provided they submit written proof that they are ISO-9001 and RC-14001 certified prior to the project bid date.

C. ProductProvide a preformed silicone joint sealing system that is capable of accommodating movements as shown in the contract plans. The preformed silicone joint seal shall be manufactured from extrusion grade organic silicone compound, and preformed by an extruding process. The preformed silicone seal shall be bonded to the joint interface with a silicone adhesive and without the use of any primers. D. Components and MaterialsThe Contractor shall furnish the selected expansion joint manufac-turer’s certificate of compliance that materials proposed will meet the requirements as set forth in these specifications.

1. Performed Silicone SealPreformed silicone seal shall be manufactured of an extrusion grade, custom organic silicone compound meeting the following physical requirements. Alternative elastomeric materials are not allowed.

2. Silicone AdhesiveThe adhesive shall be medium modulus, neutral cure sealant manu-factured of silicone meeting the following physical properties.

Wabo®Silicone Adhesive

PHYSICAL PROPERTY ASTM TEST METHOD REQUIREMENTS

Color Visual Gray



Tensile at 100% Elongation C 1184 70 PSI, Min

Peel Adhesion to substrates C 794 55 Lbs/In Min

Work Life (tool time) - 20-30 Min

Wabo®SPS Profile


Color Visual Gray

Durometer D 2240 55 +/-5

Tensile Strength D 412 1000 PSI/Min


Tear Resistance (B) D 624 100 Lbs/In Min

Compression Set at 212°F, 70 hours D 395 30% Max

rev. 9.2014


SPECIFICATION


E. Cyclic Testing of Silicone Bridge Joint SystemsThe preformed silicone joint sealing system shall be pre-qualified through cyclic testing by an independent laboratory. The cyclic testing procedure shall determine the durability of the preformed silicone joint sealing system after two hundred cycles in compression and tension. Any defects, tears or bond failure will be cause for rejection. A document signed by an independent, third party testing or inspection laboratory to verify testing will be basis of accept-ance.

CYCLIC LOADING TEST PROPERTIES

REQUIREMENTS

Test Sample Strength 2 Foot Sample

Number of Cycles 200 Cycles

Movement +/-1 (Compression, 1 tension)

Joint Opening 2 in

Joint Skew 45°

Temperature 68°F (20°C) and -20°F (- 29°C)

F. Construction RequirementsThe Contractor shall submit product information and necessary details after the award of the contract. At the discretion of the Engineer, the manufacturer may be required to furnish a representative sample of materialto be supplied in accordance with these specifications.Store all materials per manufacturer’s recommenda-tions.

Payment will be made under:

PAY ITEM PAY UNIT Preformed Silicone Joint Sealing System Lineal Foot

Payment will be full compensation for all work neces-sary to complete the items including furnishing and installing the preformed silicone joint sealing system and any miscellaneous patching.

The contractor shall ensure and properly prepare all joint interfaces prior to installation and in accordance with the manufacturer’s installation guidelines. Repair joint interfaces where needed and with materials approved by the expansion joint manufacturer. All joint interfaces must be completely dry prior to ap-plication of the silicone adhesive. Install the preformed silicone joint seal in one continuous length. Prior to installation, clean the silicone seal profile using a solvent approved by the manufacturer. Apply the silicone adhe-sive per manufacturer’s installation guidelines to insure complete contact with joint interface and preformed silicone seal.Position the silicone seal to the proper depth and apply silicone adhesive along each side of seal and fill per manufacturer’s installation guidelines.Preformed silicone joint sealing system shall be sized in accordance with manufacturer’s recommendations, and installed at locations shown on the contract plans.

G. PaymentThe accepted quantity of preformed silicone joint sealing system will be paid for at the contract unit price per lineal foot. Measurement of the preformed silicone joint sealing system will be taken along the centerline of the joint system between the outer limits indicated on the contract plans.

LIMITED WARRANTY:Watson Bowman Acme Corp. warrants that this product conforms to its current applicable specifications. WATSON BOWMAN ACME CORP. MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. The sole and exclusive remedy of Purchaser for any claim concerning this product, including, but not limited to, claims alleging breach of warranty, negligence, strict liability or otherwise, is the replacement of product or refund of the purchase price, at the sole option of Watson Bowman Acme Corp. Any claims concerning this product shall be submitted in writing within one year of the delivery date of this product to Purchaser and any claims not presented within that period are waived by Purchaser. IN NO EVENT SHALL WATSON BOWMAN ACME CORP. BE LIABLE FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL (INCLUDES LOSS OF PROFITS) OR PUNITIVE DAMAGES. Other warranties may be available when the product is installed by a factory trained installer. Contact your local Watson Bowman Acme representative for details. The data expressed herein is true and accurate to the best of our knowledge at the time published; it is, however, subject to change without notice©2014 Watson Bowman Acme Corp.


@ wbacorp.com


pg 2 of 2


PACKAGING AND COMPONENTS• Wabo®SPS Preformed Silicone Joint Sealing System, custom packaged to

specificlength• Wabo®SilAdhesive-29oz.cartridge• PneumaticApplicatorGun-soldindividually• Splicekit:PPPrimer(WBAPart#2717),AronAlpha241(WBAPart#2716)

PACKAGING AND COMPONENTS cont’d

INSTALLATION PROCEDURE

WatsonBowmanAcmeCorp.|95PineviewDriveAmherst,NY14228|(p)800-677-4922(f)716-691-9239|wbacorp.com

PRODUCT INFORMATION

Manufacturer:WatsonBowmanAcmeCorp95PineviewDriveAmherst,NY14228

(p)800-677-4922(f)716-691-9239wbacorp.com

Product Name:Wabo®SPSJointSystem

Thefollowinginstallationprocedureprovidesabasicguidelineforproperplacementoftheexpansionjointsys-temdescribedabove.Thisprocedureshouldbeusedinconjunctionwithapprovedshopdrawings(ifrequired),contractplans,projectspecification,andrecommendationsbythemanu-facturer.Toensureproperinstallationandperformanceoftheexpansionjointsystem,thefollowingstepsshallbecompletedbycontractorswithstaffhavingappropriateskillstoexecutestatedinstallationrequirements.

rev. 9.2014

BeforeInstallation:1. Carefullyreadandunderstandinstallationprocedure.ContactWBA’sTechnical

ServiceDepartmentat(800)677-4922forproductassistance.2. Inspectallshipmentsandmaterials formissingordamagedcomponentsand

hardware.ContactCustomerServiceat(800)677-4922withWBA’sordernumberandinvoiceforpromptassistance.

3. Inspectsubstrateoradjacentconstructionforacceptancebeforebeginningwork.Reportunacceptableconstructiontotheprojectmanagerforcorrectiveaction.

RECOMMENDED EQUIPMENTWatsonBowmanAcme recommends the followingequipmentand tools foreaseofinstallation:• Sandblastingequipmenttoremovelaitanceinnewconcrete,anddebrisorother

contaminantsforjointreplacementinblockoutarea• Air compressor capable of achieving 150 psi to operate sandblaster and

pneumaticgun• Denaturedalcoholtocleansealprofile• Whitecottonragstousewithdenaturedalcohol• Pneumaticcaulkingguntodispenseadhesive(WBAPart#40501)• Smalltoolsfortoolingadhesive• Foambacker rodorblueboard tostabilizesealprofileduring installation ifa

concreteledgenotpresent• Nonserratedbladeforcuttingseal• Solventbrush• PPPrimer(WBAPart#2717)forsplices• AronAlpha241(WBAPart#2716)forsplices

A. GENERAL

The work shall consist of furnishing and installing a Wabo®SPS Joint System inaccordance with the details shown on the plans, and the requirements of thespecifications.PlacementoftheWabo®SPSjointsystemshallconsistofpropersurfacepreparation,materialandapplicationofmaterials.Substitutionofalternatematerialsmayaffectproductperformanceandareprohibited.

PneumaticApplicatorGun(soldseparately)

B. JOINT PREPARATION

Theconcretejointinterfacemustbeclean(freeofdirt,coatings,rust,grease,oilandothercontaminants),soundanddurable.Newconcretemustbecured(minimumof14days)andalllaitanceremoved.

Durable Concrete- soundanddurableconcreteshouldhaveacappull-offstrengththatmeetsorexceedsACI503R,AppendixA.Unsound Concrete- Loose, contaminated, weak, spalled, deteriorated and/ordelaminatedconcretemustbe removed to soundconcrete and repairedprior toplacementofWabo®SPSJointSystem.Anypatchingmaterialsmustbeapprovedbymanufacturerpriortouse.Jointinterfacesshouldbesandblastedtoremoveanyresiduethatmaybepresent.Itisrecommendedthatthesandblastingoperationbeperformedintwosteps,onestepperjointinterface.Thejointshouldbeblowncleanusingcompressedair(>90psi).Thecompressedairshallbefreeofmoistureandoil.Thejointinterfacesshouldbecheckedforcleanliness.Shouldanycontaminatesremain,thenthe jointmustbere-blastedandblowncleanagain.Toinsurecleanliness,eachjointinterfaceshouldbewipedcleanwithacleanragwithoutsolventstoremoveanydustremainingaftersandblasting.

Wabo®SPS225 Wabo®SPS400

Wabo®SilAdhesive

PPPrimer AronAlpha241

Wab

o®SPSSpliceKit


For detailed step-by-step Wabo®SPS preformed silicone seal splicing and directional change procedures, please refer to the

“Seal Splice, Curb & Directional Change P r o c e d u r e s ” document found in your launch package.

Using the pneumatic adhesive applicator, pull the trigger. A cushion of compressed air will build up inside the applicator to initiate the flow of the Wabo®Sil Adhesive. Upon release of the trigger, adhesive

flow will cease. Controlling the adhesive flow rate is achieved with the integral pressure regulator fitted to the trigger handle. To increase flow, turn knob clockwise, to decrease the flow, turn the knob counter-clockwise.CAUTION: the line pressure connected to the applicator should not exceed 145 psi (1 MPa). Always disconnect the air line prior to dismantling the applicator. To ensure trouble free operation of the applicator, it should be wiped clean of all sealant residues after use with denatured alcohol.

Joint inferences should be free from dirt and debris. Sandblasting will remove any residue that may be present. After sandblasting, the joint should be blown clean using an air compressor.

INSTALLATION PROCEDURE

WatsonBowmanAcmeCorp.|95PineviewDriveAmherst,NY14228|(p)800-677-4922(f)716-691-9239|wbacorp.com

pg 2 of 2

1

Inspect joints for proper depth as detailed in theplans. A closed-cell, expanded polyethylene foam backer rod is recommended for seal depth positioning when a concrete ledge or steel stopper bar is not

present. The backer rod stablizes the seal and acts as a seat to prevent the preformed silicone seal from migrating below the joint depth requirement during installation. Proper groove depth placement is as follows:

The size of the backer rod should be approximately 20-25% greater than the joint opening to be sealed.

MinimumGrooveDepthPlacement

Modelnumber Groove(installation)depth

Wabo®SPS-225 2.625”(67mm)

Wabo®SPS-400 3.75”(95mm)

2

Unroll the Wabo®SPS preformed silicone seal to proper length adjacent to joint opening. With a clean rag, wipe the serrated sidewalls and rounded seal lugs of the silicone seal with denatured alcohol (by

others). This is to ensure a good clean surface for bonding of the adhesive.

3

4

Recommended application temperature 40°F (5°C) and rising. Contractor shall apply to both sides of the joint interface a continuous 3/8” to ½” (10mm to 12.5 mm) bead of Wabo®Sil Adhesive at the

recommended groove depth on either the backer rod or concrete/steel ledges.

5

LIMITEDWARRANTYWatsonBowmanAcmeCorp.warrantsthatthisproductconformstoitscurrentapplicablespecifications.WATSONBOWMANACMECORP.MAKESNOOTHERWARRANTY,EXPRESSORIMPLIED,INCLUDINGANYWARRANTYOFMERCHANTABILITYORWARRANTYOFFITNESSFORAPARTICULARPURPOSE.ThesoleandexclusiveremedyofPurchaserforanyclaimconcerningthisproduct,including,butnotlimitedto,claimsallegingbreachofwarranty,negligence,strictliabilityorotherwise,isthereplacementofproductorrefundofthepurchaseprice,atthesoleoptionofWatsonBowmanAcmeCorp.AnyclaimsconcerningthisproductshallbesubmittedinwritingwithinoneyearofthedeliverydateofthisproducttoPurchaserandanyclaimsnotpresentedwithinthatperiodarewaivedbyPurchaser.INNOEVENTSHALLWATSONBOWMANACMECORP.BELIABLEFORANYSPECIAL,INCIDENTAL,CONSEQUENTIAL(INCLUDESLOSSOFPROFITS)ORPUNITIVEDAMAGES.Otherwarrantiesmaybeavailablewhentheproductisinstalledbyafactorytrainedinstaller.ContactyourlocalWatsonBowmanAcmerepresentativefordetails.Thedataexpressedhereinistrueandaccuratetothebestofourknowledgeatthetimepublished;itis,however,subjecttochangewithoutnotice©2014WatsonBowmanAcmeCorp.

Forourmostcurrentinformation,[email protected]

Fold the Wabo®SPS preformed silicone seal and insert into the joint. Push the Wabo®SPS preformed silicone seal into the joint, maintaining contact with the joint interfaces and the Wabo®Sil Adhesive,

until it has rested upon the backer rod. Apply a second bead of Wabo®Sil Adhesive along each side of the seal

and fill to the top of the serrations (left). Care should be taken not to exceed the serrated areas. Tool the Wabo®Sil Adhesive on both sides to ensure the adhesive makes full contact with

the seal and substrate. The Wabo®SPS joint system will generally be ready to accept traffic within one hour after installation.

6

Seal Splice, Curb & Directional Change Procedures:


SEAL SPLICE, CURB & DIRECTIONAL CHANGE PROCEDURES


PRODUCT INFORMATION

Manufacturer:Watson Bowman Acme Corp95 Pineview DriveAmherst, NY 14228

(p) 800-677-4922(f) 716-691-9239wbacorp.com

Product Name:Wabo®SPS Joint Sealing System

The following installation procedure provides a basic guideline for proper placement of the expansion joint sys-tem described above. This procedure should be used in conjunction with approved shop drawings (if required), contract plans, project specification, and recommendations by the manu-facturer. To ensure proper installation and performance of the expansion joint system, the following steps shall be completed by contractors with staff having appropriate skills to execute stated installation requirements.

rev. 9.2014

Cut preformed silicone seal material with a non serrated blade, creating a fresh cut on both sides. A miter box is recommended to maintain a straight and accurate cut. A lubricating compound (such as denatured alcohol) could be used to cut seal.

1

Both ends of the preformed silicone seal shall be cleaned using a solvent brush and PP Primer (WBA part #2717) to cut the surface. Apply the Aron Alpha 241F (WBA part #2716) to the cut surface of the preformed silicone seal one half at a time and compress pieces together, holding in place for 30

seconds under firm pressure. It is recommended to let spliced section rest untouched for approximately 3 (three) minutes prior to flexing into the joint opening, ensuring full cure of splice adhesive.

2

Seal Splice:

Curb and Directional Changes:

Steps 1-3: Lay out markings for upturn or down turn about 2 – 3 inches from end of supplied seal.

1

2

3

For the proper Curb and Directional Change procedures, please follow steps to the right and reverse side of this page.

over >>

Before Installation:1. Carefully read and understand installation procedure. Contact WBA’s Technical

Service Department at (800) 677-4922 for product assistance.2. Inspect all shipments and materials for missing or damaged components and

hardware. Contact Customer Service at (800) 677-4922 with WBA’s order number and invoice for prompt assistance.

3. Inspect substrate or adjacent construction for acceptance before beginning work. Report unacceptable construction to the project manager for corrective action.


CURB & DIRECTIONAL CHANGE PROCEDURES


pg 2 of 2

LIMITED WARRANTYWatson Bowman Acme Corp. warrants that this product conforms to its current applicable specifications. WATSON BOWMAN ACME CORP. MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. The sole and exclusive remedy of Purchaser for any claim concerning this product, including, but not limited to, claims alleging breach of warranty, negligence, strict liability or otherwise, is the replacement of product or refund of the purchase price, at the sole option of Watson Bowman Acme Corp. Any claims concerning this product shall be submitted in writing within one year of the delivery date of this product to Purchaser and any claims not presented within that period are waived by Purchaser. IN NO EVENT SHALL WATSON BOWMAN ACME CORP. BE LIABLE FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL (INCLUDES LOSS OF PROFITS) OR PUNITIVE DAMAGES. Other warranties may be available when the product is installed by a factory trained installer. Contact your local Watson Bowman Acme representative for details. The data expressed herein is true and accurate to the best of our knowledge at the time published; it is, however, subject to change without notice©2014 Watson Bowman Acme Corp.


@ wbacorp.com


Using a sharp knife, remove only the flap, following along the marks made on the seal. At this point, leave the center intact.

4

Fold the seal in half. Holding tightly, continue to cut through the center. Cut both ends to be spliced.

5

Using PP Primer S, clean both surfaces to be bonded, and allow to dry.

6

Starting at edge, apply the Aron Alpha 241 to one side of the seal only.

7

Align edges and press firmly together for 30 seconds.Continue gluing along edge until reaching the center of the seal. DO NOT GLUE CENTER. Repeat along other edge leaving center unglued.

8

Once both sides are glued, align center, apply glue and allow to dry. Check for gaps and fix if necessary.

Using Wabo®Sil Adhesive, place a bead 1/2” over splice on front and back of seal to ensure seamless bond.

9


Wabo®SPS Joint Sealing System Not to Scale


@ wbacorp.com


Additional sizes and information can be found on wbacorp.com. This system size shown for illustrative purposes.


SYSTEM DETAIL rev. 9.2014


Wabo®SPS Joint Sealing System Not to Scale


@ wbacorp.com


Additional sizes and information can be found on wbacorp.com. This system size shown for illustrative purposes.

LIMITED WARRANTY:Watson Bowman Acme Corp. warrants that this product conforms to its current applicable specifications. WATSON BOWMAN ACME CORP. MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. The sole and exclusive remedy of Purchaser for any claim concerning this product, including, but not limited to, claims alleging breach of warranty, negligence, strict liability or otherwise, is the replacement of product or refund of the purchase price, at the sole option of Watson Bowman Acme Corp. Any claims concerning this product shall be submitted in writing within one year of the delivery date of this product to Purchaser and any claims not presented within that period are waived by Purchaser. IN NO EVENT SHALL WATSON BOWMAN ACME CORP. BE LIABLE FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL (INCLUDES LOSS OF PROFITS) OR PUNITIVE DAMAGES. Other warranties may be available when the product is installed by a factory trained installer. Contact your local Watson Bowman Acme representative for details. The data expressed herein is true and accurate to the best of our knowledge at the time published; it is, however, subject to change without notice©2014 Watson Bowman Acme Corp.


SYSTEM DETAIL pg. 2 of 2



PREJOB SURVEY rev. 9.2014


@ wbacorp.com

Company:phone/fax:Project Name:Project City/State:

Check appropriate boxes and fill in necessary information.

Expansion Joint Work to be Performed: New Construction Resealing Rehabilitation

Existing Joint Conditions: Concrete Substrate Steel Substrate Other: __________________________

Anticipated Joint Movement: Thermal +/- __________ Vertical Deflection +/- __________ Racking (skew) +/- __________

Joint Information and Configuration:

Joint Location # ______________________________________

Field Measurement gap “A” in inches: __________ Field Measurement right blockout “F” in inches: __________ and by “E” in inches: __________ Field Measurement left blockout “F” in inches: __________ and by “E” in inches: __________ Deck Surface temperature: __________ Ambient temperature: __________ Gap widths varies “A” from _____ to _____ over __________ length of joint Groove depth restrictions “B” in inches: __________ Straight joint: [ Y or N ] Skewed joint (note skew angle): ________ Field Measurement joint length: ________

Questions? One rule: Contact WBA. 800-677-4922716-691-7566

[email protected]

Enter joint opening dimensions Enter blockout dimensions and deck thickness

A: _______(in) B: _______(in)

A

E: _______(in) F: _______(in)

BE E

FF

Name/Title:email:Project Number:Project Agency/Owner:

Technical ExpertiseMore than 60 years of practical experience and knowledge in the Expansion Control industry allows WBA to develop solutions and make recommendations for the right product choice for your application.

InnovationOffering the broadest range of products and services in the construction industry, we are the only company servicing the entire portfolio of Bridge and Highway, Architectural, Parking and Stadium markets. We support these markets with a fully qualified team of professional engineers and designers backed by strong relationships with national testing labs and universities.

Custom SolutionsWBA provides more than just technical expertise - we supply engineered solutions that make good sense. We offer a growing range of high performance Wabo® products and systems to provide long lasting solutions to difficult repair problems. We are fully resourced to deliver results and exceed the expectations of our customers.

QualityWBA is dedicated in providing the highest quality products and services to our customers. Our professional opera-tions team employs the principles of lean manufacturing, and enterprise resource planning tools, all supported by our formal ISO 9001:2008, RC 14001 and AISC quality management systems.

Watson Bowman Acme Corp.95 Pineview Drive | Amherst, NY 142281-800-677-4WBA (4922) | [email protected] © 2014 Watson Bowman Acme Corp.All rights reserved / Printed in USA

BASF - The Chemical Company

BASF is a leader in the construction industry. With more than 600 products serving 75 construction product categories, we offer the broadest portfolio of products used directly on construction sites or integrated into pther products, to increase energy efficiency and life expectancy, offer faster construction processes and improve health, safety and comfort.

We also enable high performance with less material, energy consumption, waste and emissions. BASF materials, pro-cesses and solutions respect local economic requirements, and support the creation of higher living standards. At BASF, we create chemistry for a sustainable future.

Wabo®SPS preformed silicone joint sealing system


Find your local WBA/BASF sales representativewbacorp.com/contact-us/local-rep

Interested in our Wabo®SPS expansion joint system?Learn Even More!

SPS Folder-Launch-webSPS Launch DataSheet-webSPS Launch Specification-webSPS Launch Installation Procedure-webSPS Launch System Details-webSPS Launch PreJob Survey-web

Environmentally and chemically resistant. Multi-directional ... - RAB€¦ · SPS expansion joint...

Documents

Transcript of Environmentally and chemically resistant. Multi-directional ... - RAB€¦ · SPS expansion joint...