1

ENGLISH

Declaration of ConformityManufacturer: InFocus Corporation, 27700B SW Parkway Ave. Wilsonville, Oregon 97070 USAEuropean Office: Strawinskylaan 585, 1077 XX Amsterdam, The NetherlandsWe declare under our sole responsibility that the ScreenPlay 5700 projector conforms to the following directives and norms:

EMC Directive 89/336/EEC, Amended by 93/68/EECEMC: EN 55022 EN 55024

EN 61000-3-2 EN 61000-3-3

Low Voltage Directive 73/23/EEC, Amended by 93/68/EECSafety: EN 60950: 2000

May, 2003

TrademarksApple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc. IBM is a trademark or registered trademark of International Business Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered trademarks of Microsoft Corporation. Digital Light Processing is a trademark or reg-istered trademark of Texas Instruments. Faroudja, DCDi, and TrueLife are trade-marks or registered trademarks of Faroudja. InFocus and ScreenPlay are trademarks or registered trademarks of InFocus Corporation.

FCC WarningNote: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:--Reorient or relocate the receiving antenna.--Increase the separation between the equipment and receiver.--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.--Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by InFocus Corporation can void the user's authority to operate the equipment.

CanadaThis Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Agency ApprovalsUL, CUL, TÜV, NOM, IRAM, GOST, CCC, MIC, C-Tick

2

Table of Contents

Introduction 3Positioning the projector 5Video connections 6Connecting a video device 7Displaying a video image 8Connecting a computer 10Shutting down the projector 11Troubleshooting your setup 11Using the keypad buttons 18Using the remote control 19Optimizing video images 20Customizing the projector 20Using the menus 21

Picture menu 22Settings menu 27

Maintenance 29Cleaning the lens 29Replacing the projection lamp 30

Appendix 32Specifications 32Accessories 32Red LED behavior and projector errors 33Projected image size 33Source compatibility 34Projector dimensions for ceiling mount installations 35RS-232 terminal specifications 36

For complete details on connecting and operating the projector, refer to this User’s Guide. Electronic versions of this User’s Guide in multiple languages are available on our website at www.infocushome.com/support.

The website also has technical specifications (an interactive image size cal-culator, laptop activation commands, connector pin outs, a glossary, the product data sheet), a web store to buy accessories, and a page for online registration.

Important Operating ConsiderationsDo not place the projector on a tablecloth or other soft covering that may block the vents. Vents are placed along the left and right sides of the projec-tor, as well as across the front of the projector. Do not use a non-approved ceiling mount. In the unlikely event of the lamp rupturing, discard any edi-ble items placed in the surrounding area and thoroughly clean the area along the sides and in the front of the projector.

2 ft (.6m) 2 ft (.6m)

2 ft (.6m)

Do not place objects in the areas along the side and in the front of the projector

3

IntroductionCongratulations and thank you for your excellent choice of a superior digi-tal image projection device. Your new ScreenPlay™ 5700 projector from InFocus® is specifically designed for home cinema applications. The ScreenPlay 5700 sets the standard for Enhanced-Definition digital perfec-tion, featuring true Enhanced Definition 1024x576 resolution using the latest DLP™ technology and new DCDi video processing from Faroudja™. Cali-brated to D65 color mastering standards, the ScreenPlay 5700 reproduces colors and details the way the director intended. Whether you are watching movies or High Definition broadcasts or playing the latest video game, you will enjoy breathtaking image quality.

Online RegistrationRegister your projector online at www.infocus.com/service/register to receive product updates, announcements, and registration incentives.

Included items

Projector components and features

user’s guide, safety card

remote

projector

lens cap

powercable*

SCARTcable

cable cover

keypad

zoomfocus

elevator foot release

remotecontrolreceiver (IR)

air intakevent

IR

I/O panel

leveling foot

exhaust

heat vent

remote controlreceiver (IR)

IR

*country-dependent

4

Connector PanelThe projector provides eight discreet video connectors:

• two component RCA

• two S-video

• one composite RCA

• one M1-DA (HD, DVI, and computer)

• one VESA (HD, HD component, and computer)

• one component D5

It also has a mini-jack input for a Niles or Xantech-compatible IR repeater and an RS-232 connector for serial control. The Command Line Interface (CLI) specifications and commands are listed in the Appendix starting on page 36.

Two 3.5 mm mini-jack triggers provide 12 volt current. Trigger 1 provides a constant output while the projector is on. If you connect your projection screen to Trigger 1, when you turn on the projector the screen will move down; when you turn the projector off, the screen will return to the storage position. Trigger 2 provides a 4:3 aspect trigger. When you select 4:3 in the Aspect Ratio menu or from the Resize button on the remote, a 12v signal will be sent after a three second delay. Use this trigger for screens with 4:3 aspect curtains. When you switch back to 16:9 format, the curtains open to reveal the entire screen.

For details on each connector type and their inputs, see page 34.

IR in

1

2

Y Y

Pr Pr

Pb Pb

serial control

M1-DA vesa trigger 1821

3

4

6

5

7

trigger 2

component

s-video

video

D5

component

lock

remote controlreceiver (IR)

powerconnector

s-videovideo

componentvideo

video/computer1 & 2

serialconnector

D5video

IR input

12v triggers

screen trigger connection

3.5mm mono plug

+12v

ground

to screen relay (see screen manufacturerfor details)

5

Positioning the projectorThere are a number a factors to consider when determining where to set up the projector, including the size and shape of your screen, the location of your power outlets, and the distance between the projector and the rest of your equipment. Here are some general guidelines.

1 Position the projector on a flat surface at a right angle to the screen.

The projector must be within 10 feet (3 m) of your power source. To ensure adequate cable access, place the projector at least 6 inches (0.15m) from a wall or other objects. Place the projector at least 5.6 feet (1.7 m) from the projection screen.

If you install the projector on the ceiling, refer to the installation guide that comes with the Ceiling Mount Kit for more information. To turn the image upside down, see page 27. InFocus recommends use of an authorized InFocus ceiling mount. The Ceiling Mount Kit is sold sepa-rately, see page 32.

2 Position the projector the desired distance from the screen.

The distance from the lens of the projector to the screen, the zoom set-ting, and the video format determine the size of the projected image. For more information about projected image sizes, see page 33.

The image exits the projector at a given angle. This image offset is 133%. This means that if you have an image 10’ high, the bottom of the image will be 3.3’ above the center of the lens.

Go to www.infocushome.com/support for a complete image size calcula-tor.

lens center

bottom of image3.3’ above lens

10’ highimage

6

Video connectionsYou can connect VCRs, DVD players, camcorders, digital cameras, video games, HDTV receivers, and TV tuners to the projector. (You cannot directly connect the coaxial cable that enters your house from a cable or satellite company; the signal must pass through a tuner first. Examples of tuners are digital cable boxes, VCRs, digital video recorders, and satellite TV boxes. Basically, any device that can change channels is considered a tuner.) Audio must be provided by your own speakers, as the projector has no separate audio controls. If there is more than one output, select the highest quality one. DVI, Component video and RGB (M1, HD15) have the best quality, fol-lowed by S-video, and then composite video.

For a complete list of compatible sources, see page 34 of the Appendix.Table 1: Video connections

Input signal ConnectorConnector label on projector

Standard Broadcast TV (not HDTV), via cable, digital cable, satellite TV, DirectTV

Component videoS-videoComposite video

Component 3, 6S-video 4, 5Video 7

HDTV Component videoVESADVI

Component 3, 6VESA 2M1-DA 1

DVD Component videoS-videoComposite video

Component 3, 6S-video 4, 5Video 7

VCR Composite videoS-videoComponent video

Video 7S-video 4, 5Component 3, 6

Video Camera Composite videoS-video

Video 7S-video 4, 5

Video Game VESAComposite videoS-videoComponent video

VESA 2Video 7S-video 4, 5Component 3, 6

IR in

1

2

Y Y

Pr Pr

Pb Pb

serial control

M1-DA vesa trigger 1821

3

4

6

5

7

trigger 2

component

s-video

video

D5

component

s-videovideo

componentvideo

M1-DA VESA

7

Connecting a video device If your video device has more than one output, select the highest quality one. DVI video has the best quality, followed by Component video, S-video, and then composite video. If the video device uses component cable connectors, plug the cable’s green connectors into the green component-out connector on the video device and into the green component connector (labeled “Y”) on the projector. Plug the component cable’s blue connectors into the blue component-out connector on the video device and into the blue component connector (labeled “Pb”) on the projector. Plug the component cable’s red connectors into the red component-out connector on the video device and into the red component connector (labeled “Pr”) on the projector. If the video device uses a round, four-prong S-video connector, plug an S-video cable into the S-video connector on the video device and into the S-video connector on the projector. If the video device uses a yellow composite video connector, plug a compos-ite video cable’s yellow connector into the video-out connector on the video device. Plug the other yellow connector into the yellow Video connector on the projector.

If the video device uses a DVI connector, plug an M1-D cable into the video-out connector on the video device. Plug the other connector into the M1-DA connector on the projector.

If the video device uses a VESA connector, plug a VESA cable into the video-out connector on the video device. Plug the other connector into the VESA connector on the projector.

Connecting the power cable

Connect the power cable to the connector on the back of the projector and to your electrical outlet. The Power LED on the keypad turns solid green. NOTE: Always use the power cable that shipped with the projector.

connect component cableIR in

1

2

Y Y

Pr Pr

Pb Pb

serial control

M1-DA vesa trigger 1821

3

4

6

5

7

trigger 2

component

s-video

video

D5

component

connect S-video cableIR in

1

2

Y Y

Pr Pr

Pb Pb

serial control

M1-DA vesa trigger 1821

3

4

6

5

7

trigger 2

component

s-video

video

D5

component

connect composite video cableIR in

1

2

Y Y

Pr Pr

Pb Pb

serial control

M1-DA vesa trigger 1821

3

4

6

5

7

trigger 2

component

s-video

video

D5

component

connect M1-D cableIR in

1

2

Y Y

Pr Pr

Pb Pb

serial control

M1-DA vesa trigger 1821

3

4

6

5

7

trigger 2

component

s-video

video

D5

component

connect VESA cableIR in

1

2

Y Y

Pr Pr

Pb Pb

serial control

M1-DA vesa trigger 1821

3

4

6

5

7

trigger 2

component

s-video

video

D5

component

connect power cable

IR in

1

2

Y Y

Pr Pr

Pb Pb

serial control

M1-DA vesa trigger 1821

3

4

6

5

7

trigger 2

component

s-video

video

D5

component

8

Displaying a video imageRemove the lens cap.

Press the Power button on the top of the projector.

The projector chimes if the chime feature is enabled (page 28). The LED flashes green and the fans start to run. When the lamp comes on, the startup screen displays and the LED is steady green. It can take a minute for the image to achieve full brightness.

? No startup screen? Get help on page 12.

Plug in and turn on the video device.

An image from the video device should appear on the projection screen. If it doesn’t, press the Source button on the keypad.

Adjust the height of the projector by pressing the release button to extend the elevator foot. Rotate the leveling foot, if necessary.

Position the projector the desired distance from the screen at a 90 degree angle to the screen. See page 33 for a table listing screen projected image sizes and distances to the screen.

remove lens cap

press Power

turn on video device

adjust height

rotateleveling footelevator

foot

adjust distance

9

Adjust the zoom or focus rings by rotating them until the desired image size and sharpness are produced.

If the image is not square, adjust the keystone using the buttons on the key-pad. Press the upper Keystone button to reduce the width of the upper por-tion of the image, and press the lower Keystone button to reduce the width of the lower portion.

The Contrast, Brightness, Color, andTint are factory calibrated to D65 col-ors, but you can adjust these settings in the Picture menu if necessary.

See page 21 for help with the menus.

adjust zoom and focus

focus

zoom

adjust keystone

adjust Picture menu

10

Connecting a computer

Connect either a VESA cable or M1 cable into the appropriate connector on the projector. Connect the other end to the video port on your computer. If you are using a desktop computer, you first need to disconnect the monitor cable from the computer’s video port.

Connect the power cable to the connector on the back of the projector and to your electrical outlet.

The Power LED on the projector’s keypad turns solid green.

NOTE: Always use the power cable that shipped with the projector.

Turn on the projector, then your computer.

You can control the projector from an LCD control panel or computer by connecting an RS-232 cable to the projector’s Serial connector. Specific RS-232 commands can be found in the Appendix starting on page 37 and in the Service and Support section of our website at www.infocushome.com/support.

IR in

1

2

Y Y

Pr Pr

Pb Pb

serial control

M1-DA vesa trigger 1821

3

4

6

5

7

trigger 2

component

s-video

video

D5

component

connect computer cable

IR in

1

2

Y Y

Pr Pr

Pb Pb

serial control

M1-DA vesa trigger 1821

3

4

6

5

7

trigger 2

component

s-video

video

D5

component

connect power cableIR in

1

2

Y Y

Pr Pr

Pb Pb

serial control

M1-DA vesa trigger 1821

3

4

6

5

7

trigger 2

component

s-video

video

D5

component

connect RS-232 cableIR in

1

2

Y Y

Pr Pr

Pb Pb

serial control

M1-DA vesa trigger 1821

3

4

6

5

7

trigger 2

component

s-video

video

D5

component

11

Shutting down the projectorPower Save

The projector has a Power Save feature in the System menu that automati-cally turns the lamp off after no signals are detected for 20 minutes. After 10 additional minutes with no signal, the projector powers down. If an active signal is received before the projector powers down, the image is displayed. You must press the Power button to display an image after 30 minutes have passed.

Turning off the projector

To turn off the projector, press the Power button. The lamp turns off and the LED blinks green for about one minute while the fans continue to run to cool the lamp. When the lamp has cooled, the LED lights green and the fans stop. Unplug the power cable to completely power off the projector.

Troubleshooting your setupIf your image appears correctly on the screen, skip to the next section (page 18). If it does not, troubleshoot the setup.

The LED on top of the projector’s keypad indicates the state of the projector and can help you troubleshoot.

The following table shows some potential problems. In some cases, more than one possible solution is provided. Try the solutions in the order they are presented. When the problem is solved, you can skip the additional solutions.

Table 2: LED behavior and meaning

LED color/behavior Meaning

solid green The projector is plugged in, or the projec-tor has been turned on and the software has initialized. The projector has been turned off and the fans have stopped.

blinking green The Power button has been pressed and the software is initializing, or the projec-tor is powering down and the fans are running to cool the lamp.

blinking redThe projector will not start up if the LED is blinking red. You must correct the prob-lem, disconnect and reconnect the power cable, then power on the projector.

See page 33 for more information on blinking red LEDs.

A fan (blinks 4 times) or lamp (blinks 3 times) failure has occurred. Turn off the projector and wait one minute, then turn the projector on again. Also check for a blocked vent or a stopped fan (blinks 5 times).

solid red An unidentifiable error: please contact Technical Support.

12

Problem Solution Result

No startup screenPlug power cable in and remove lens cappress Power button Correct image

Image not centered on screen Move projector, adjust zoom, adjust height Correct image

ScreenPlay

Adjust horizontal or vertical position in Picture>Advanced menu

zoom

13

Image not square Adjust keystone on keypad Square image

Image does not fit 16:9 screen

Change aspect ratio to 16:9 in Picture>Aspect ratio menu Correct image

Edges of image distortedTurn Overscan on in the Picture menu

Correct image

A B A B

14

1. Projected colors don’t match source

2. Colors are washed out or too deep3. Image from component source appears greenish

1. Adjust color, tint, color temperature, brightness, or contrast in the menus.2. Pick another gamma setting3. Pick another color space Correct image

Image upside down Turn off Ceiling in Settings>System menu Correct image

Image reversed left to right Turn off Rear in Settings>System menu Correct image

COLOR COLOR

ABA B

A A B

15

Video image “torn” and fragmentedChange Video Standard in Picture>Advanced menu Correct image

Lamp won’t turn on, LED blinking red (page 11)Make sure vents aren’t blocked; allow projector to cool for one minute

Unplug projector; wait one minute; plug in projector and turn it on: lamp lights

AABB A B

blinksred

ScreenPlay

16

Computer-specific troubleshooting

Only startup screen appearsPress the Source button

Activate laptop’s external portComputer image projected

No computer image, just the words “Signal out of range”

Adjust computer refresh rate in Control Panel>Display>Settings>Advanced>Adapter (location varies by operating system)

Computer image projected

AScreenPlay or restart

laptop

A A

ASignal out ofrange

A A

17

Still having problems?If you need assistance, call InFocus Customer Service directly at1-800-799-9911. Support is free between 6 a.m. and 6 p.m. PST, Monday through Friday. Support is available in North America after hours and weekends for a fee at 1-888-592-6800.

Or, send us an e-mail at techsupport@infocus.com.

In Europe, call InFocus in The Netherlands at (31) 20 579 2820.

In Asia, call InFocus in Singapore at (65) 6334-9005.

This product is backed by a limited two-year warranty. When sending the projector in for repair, we recommend shipping the unit in its original pack-ing material, or having a professional packaging company pack the unit with all accessories for shipping. An optional ATA shipping case is available for purchase that provides adequate protection for shipping. Please insure your shipment for its full value.

Image fuzzy or cropped Set your computer’s display resolution to the native resolution of the projector (Start>Settings>Control Panel>Display>Settings tab, select 1024x576)

Image clear and not cropped

AAAFor a laptop,disable laptopmonitoror turn-on dual-display mode

A

18

Using the keypad buttonsMost buttons are described in detail in other sections, but here is an over-view of their functions:

Power–turns the projector on (page 8) and off (page 8).

Menu–opens the on-screen menus (page 21).

Select–confirms choices made in the menus (page 21).

Up/down arrows–navigates to and adjusts settings in the menus (page 21).

Auto image–resynchs the projector to the source.

Presets–cycles through the 3 available user preset settings (page 24).

Keystone–adjusts squareness of the image (page 9 and page 22).

Brightness–adjusts intensity of the image (page 22).

Resize–changes the aspect ratio (page 22).

Source–changes the active source (page 27).

menu navigation buttons

19

Using the remote controlThe remote uses two (2) provided AAA batteries. They are easily installed by sliding the cover off the remote’s back, aligning the + and - ends of the batteries, sliding them into place, and then replacing the cover.

To operate, point the remote at the projection screen or at the projector (not at the video device or computer). The range of optimum operation is 0 to 30 feet (9.14m).

Press the remote’s Menu button to open the projector’s menu system. Use the arrow buttons to navigate, and the Select button to select features and adjust values in the menus. See page 21 for more info on the menus.

The remote also has:

• Power button to turn the projector on and off (see page 11 for shut-down info)

• backlight button to light the remote’s buttons in the dark

• Brightness and Contrast buttons to adjust the image

• Blank button to display a blank screen instead of the current image (to change the color of the screen, see page 28)

• Source buttons to switch among sources (to assign a particular source to a source button, see page 27) and a source toggle

• Resize button to change the Aspect Ratio (see page 22)

• Auto Image button to resynch the projector to the source

• Preset button to restore stored settings (see page 24)

• Overscan button to remove noise in a video image (page 24)

Troubleshooting the remote• Make sure the batteries are installed in the proper orientation and are

not dead.

• Make sure you’re pointing the remote at the projector or the screen, not at the video device or the computer, and are within the remote range of 30 feet (9.14m).

backlight buttonnavigation buttons

20

Optimizing video imagesAfter the video device is connected properly and the image is on the screen, you can optimize the image using the onscreen menus. For general informa-tion on using the menus, see page 21.

• Change the Aspect ratio. Aspect ratio is the ratio of the image width to image height. TV screens are usually 1.33:1, also known as 4:3. HDTV and most DVDs are 1.78:1, or 16:9. Choose the option that best fits your input source in the menus, or press the Resize button on the remote to cycle through the options. See page 22.

• Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture menu. See page 22.

• Select a different Color Temperature or use the Color Control to adjust the gain and offset of the red, green, and blue color. See page 26.

• Select a specific Color Space or Gamma. See page 26.

• Select a different Video Standard. Auto tries to determine the standard of the incoming video. Select a different standard if necessary. See page 26.

• Turn overscan on to remove noise around the video image. See page 24.

• Fine tune component inputs using the TrueLife™ adjustments. See page 25.

• Tune colors to your specifications using Blue Only, Color Wheel Index, and ADC Calibration. See page 29.

• Choose High Power to maximize the light output. See page 27.

• Make sure your DVD player is set for a 16:9 television. See your DVD player’s user’s guide for instructions.

Customizing the projectorYou can customize the projector for your specific setup and needs. See page 27 to page 29 for details on these features.

• For rear projection, turn Rear mode on in the Settings>System menu.

• For ceiling mounted projection, turn Ceiling mode on in the Set-tings>System menu.

• Turn the projector’s display messages and power-on chime on and off.

• Turn on power saving features.

• Specify blank screen colors and startup logos. Make the menus translu-cent.

• Specify the menu language.

21

Using the menusTo open the menus, press the menu button on the keypad or remote. (The menus automatically close after 60 seconds if no buttons are pressed.) The Main menu appears. Use the arrow buttons to move up and down to high-light the desired submenu, then press the Select button.

To change a menu setting, highlight it, press Select, then use the up and down arrow buttons to adjust the value, select an option using radio but-tons, or turn the feature on or off using check boxes. Press Select to confirm your changes. Use the arrows to navigate to another setting. When your adjustments are complete, navigate to Exit, then press Select to navigate to the previous menu; press the Menu button at any time to close the menus.

Dots appear before the menu name. The number of dots indicate the menu’s level, ranging from one (the Main menu) to four (the most nested menus).

The menus are grouped by usage:

• The Picture menu provides image adjustments.

• The Settings menu provides set-up type adjustments that are not changed often.

• The About menu provides a read-only display of information about the projector and source.

Certain menu items may be hidden until a particular source is connected. For example, Tint is only available for NTSC video sources and will be hid-den when other sources are active. Other menu items may be grayed out when they are not available. For example, Brightness is grayed out until an image is active.

Keypad navigation buttons

Main menu

Menubutton

Picture menu

Settings menu

Dots

About menu

22

Picture menuTo adjust the following five settings, highlight the setting, press Select, use the up and down arrows to adjust the values, then press select to confirm the changes. All menu defaults are listed in a table starting on page 37.

Keystone: adjusts the image vertically and makes a squarer image. You can also adjust keystone from the keypad.

Contrast: controls the degree of difference between the lightest and darkest parts of the picture and changes the amount of black and white in the image.

Brightness: changes the intensity of the image. You can also adjust bright-ness from the keypad.

Color: (video sources only) adjusts a video image from black and white to fully saturated color.

Tint: (NTSC video sources only) adjusts the red-green color balance in the image.

Aspect Ratio: Aspect ratio is the ratio of the image width to image height. TV screens are usually 1.33:1, also known as 4:3. HDTV and most DVDs are 1.78:1, or 16:9. You can choose Native, 4:3, 16:9, Letterbox, or Natural Wide. The default is 16:9. The goal is to show the most detail on the screen while preserving the ratio of width to height. The native resolution of the projec-tor is 1024x576. Use Native, 4:3 or Naural Wide for 4:3 input sources; use Native, 16:9 or Letterbox for 16:9 input. Pressing the Resize button on the remote cycles through these options.

Native: this mode bypasses the internal scaler, displaying the image with no resizing. Since the native resolution is 1024x576 and 4x3 video images are approximately 640x480, 4x3 images will always be smaller than the dis-play and will be centered in the display. Computer images 1024x768 or smaller will also be centered in the display. If a 16x9 video source or a 1280x1024 or larger computer source is viewed, it will display up to 1024 pixels and 576 lines from the center of the input.

increasing keystonedecreasing keystone

Aspect ratio

23

16:9: the default is 16:9, which preserves the 16:9 aspect ratio and is designed to be used with content that is Enhanced for Widescreen TVs.

4:3: resizes the image from its original version to fit a standard 4:3 aspect ratio screen. If you have a 4:3 source on a 16:9 screen, the image is placed in a 16:9 space, so black bars appear at the sides of the image.

Letterbox: preserves the 16:9 aspect ratio. If you have a 16:9 source and screen, the image fills the screen. If your source is letterboxed, the image expanded to fill the screen.

Natural Wide: this mode stretches a 4:3 image to fill the entire 16:9 screen. The center two-thirds of the image is unchanged; the edges of the image are stretched.

1616

9 9

16:9 image input 16:9 image

16:9aspect ratio

16

9

4

3

4:3 image input 4:3 image on 16:9 screen

blac

k ba

rs

blac

k ba

rs4:3 aspect ratio

16

9

letterbox image input 16:9 image fills 16:9 screen

black bars

black bars

4

3letterboxaspect ratio

4:3 image fills 16:9 screen

natural wideaspect ratio

4:3 image input

4

3

16

9

24

Presets: This allows you to customize settings and save the settings to be restored later. To restore the factory default settings, choose Factory Reset in the Settings>Service menu.

To set a preset for the current source, adjust the image, select Save Settings in the Presets menu, then choose Save User 1, 2, or 3. You can recall these settings in the future by selecting the appropriate user presets.

Gamma: Gamma tables contain preset intensity configurations optimized for the input source. You can select a gamma table that has been specifically tuned for either film, video, Bright Room, or PC input. (Film input is mate-rial originally captured on a film camera, like a movie; video input is mate-rial originally captured on a video camera, like a TV show or sporting event.) White Peaking increases the brightness of whites that are near 100%.

NOTE: Your viewing preferences may vary. Cycle through the gamma options and pick the one you like the best.

Overscan: lets you crop the input or zoom the input if desired.

Save User Presets

Presets

Gamma

Overscan

25

Advanced settingsThe following 4 options are for computer or HDTV sources only.

Phase: adjusts the phase of the video signal’s digital conversion.

Tracking: adjusts the frequency of the video signal’s digital conversion.

Horizontal/Vertical Position: adjusts the position of the source.

TrueLife: This option refers to Faroudja’s TrueLife processing of the image. All standard definition interlaced video signals (composite, S-video and component) are routed through this processor. Extended and High Defini-tion progressive component sources are not routed though this processor by default. You can turn TrueLife on to route these signals through the proces-sor and then adjust the following 3 options:

Chroma Detail: This adjusts the color sharpness.

Luma Detail: This adjusts the sharpness.

Chroma Delay: aligns the Luma and Chroma Detail

CCS: (Cross Color Suppression) processes the signal to remove any color information from the luma portion of the signal. It is On for all composite signals, and can be turned off for S-video and inter-laced component sig-nals.

Film Mode: controls deinterlacing. 2:2/3:2 Enable If selected, the deinter-lacer attempt to perform 3:2 pulldown, assuming the source was originally created on 24fps film. If the original source is 30fps film, you should select NTSC 2:2 pulldown.

Noise Reduction: adjusts signal noise reduction. Choose Off to have no noise reduction, choose Auto to have the software determine the amount of noise reduction, or choose Manual and adjust the Level. Skintone Bypass prevents the noise reduction processing from being applied to skin tones. Images of people often look better with less process-ing. Available when Auto or Manual are selected.

Advanced

True Life

Film Mode

Noise reduction

26

Color Space: This option applies to computer and HDTV sources (it won’t appear in the menu for video sources). It allows you to select a color space that has been specifically tuned for the video input. When Auto is selected, the projector automatically determines the standard. To choose a different setting, turn off Auto, then choose RGB for computer sources, choose REC709 for component 1080i or 720p sources, or choose REC601 for compo-nent 480p or 576p sources.

Color Temperature: changes the intensity of the colors. Select a listed value.

Color Control: allows you to individually adjust the gain (relative warmth of the color) and the offset (the amount of black in the color) of the red, green, and blue colors.

Video Standard: When it is set to Auto, the projector attempts to pick the video standard automatically based on the input signal it receives. (The video standard options may vary depending on your region of the world.) If the projector is unable to detect the correct standard, the colors may not look right or the image may appear “torn.” If this happens, manually select a video standard by selecting NTSC, PAL, or SECAM from the Video Stan-dard menu.

Color Space

Color Temperature

Color Control

Video Standard

27

Settings menuSources: allows you to assign a particular input to a specific source key on the remote and enables or disables Autosource. When Autosource is not checked, the projector defaults to the last-used source. If no source is found, a blank screen displays. When Autosource is checked, the projector checks the last-used source first at power up. If no signal is present, the projector checks the sources in order until a source is found or until power down.

You can use the Source Enable feature to eliminate certain sources from this search, which will speed the search. By default, the check boxes for all sources are checked. Uncheck a source’s box to eliminate it from the search.

System

All options in this menu toggle between on and off.

Rear: reverses the image so you can project from behind a translucent screen.

Ceiling: turns the image upside down for ceiling-mounted projection.

NOTE: It is recommended that all final image adjustments in Ceiling mode are made once the unit has fully warmed up (approximately 20 minutes).

Auto Power: When Auto Power is checked, the projector automatically goes into the startup state after the projector receives power. This allows control of ceiling mounted projectors with a wall power switch.

Display Messages: displays status messages (such as “Searching”) in the lower-left corner of the screen.

High Power: Turn this on to increase the light output of the lamp. This also shortens lamp life and increases fan noise.

SourcesSettings menu

Source EnableSource 1

System menu

28

Translucent OSD: makes the menus translucent. This prevents the image from being completely covered by the menus while you are making image adjustments.

Chime: turn this on to hear a sound when the Power button is pressed.

Sleep Timer: allows you to force the projector to automatically shutoff after 4 hours.

Power Save: when On, the lamp is automatically turned off after no signals are detected for 20 minutes. After 10 additional minutes with no signal, the projector powers down. If an active signal is received before the projector powers down, the image will be displayed.

Startup Logo: allows you to display a blank Black, White, or Blue screen instead of the default screen at startup and when no source is active or detected.

Blank Screen: determines what color displays when you press the Blank button on the remote or when no source is detected.

Language: allows you to select a language for the onscreen display of menus and messages.

System menu

Startup logo

Blank Screen

Language

29

Service: to use these features, highlight them and press Select.

Factory Reset: restores all settings (except Lamp Hours) to their default after displaying a confirmation dialog box.

Test Pattern: displays a test pattern when the Blank button on the remote is pressed. To select the patterns, use the up/down arrows on the remote or keypad.

Blue Only: turns off the Red and Green portions of the input, allowing you to properly adjust the color balance with a SMPTE color bar pattern.

Color Wheel Index: makes the hue of various gray levels consistent.

ADC Calibration: allows adjustment of the calibrated ADC values so that color accuracy can be optimized. Adjust the slidebars for each value and note the change in the appropriate color. Use a component input when adjusting the Component controls.

Service Code: only used by authorized service personnel.

Maintenance

Cleaning the lens1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.

Avoid using an excessive amount of cleaner, and don’t apply the cleaner directly to the lens. Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.

2 Lightly wipe the cleaning cloth over the lens in a circular motion. If you don’t intend to use the projector immediately, replace the lens cap.

Service menu

clean the lens with a soft dry clothand non-abrasivecleaner

30

Replacing the projection lampThe lamp hour timer in the About menu counts the number of hours the lamp has been in use. After 1980 hours, the message “Change lamp” briefly appears on the screen at each startup. To maintain optimal video perfor-mance, we recommend changing the lamp after 2000 hours, depending on usage. You can order new lamp modules from your dealer. See “Accesso-ries” on page 32 for information.

1 Turn off the projector and unplug the power cable.

2 Wait 60 minutes to allow the projector to cool thoroughly.

3 Turn the projector upside down and remove the lamp door by removing the two screws and sliding the lamp door tabs out of the three tab bays.

CAUTION: Never operate the projector with the lamp door removed. This disrupts the air flow and causes the projector to overheat.

4 Loosen the captive screw on the lamp module.

Lamp hours used

turn off and unplugthe projector

wait 60 minutes

loosen the screw on lamp module

bail wire

31

WARNINGS:

• To avoid burns, allow the projector to cool for at least 60 minutes before you replace the lamp.

• Do not drop the lamp module. The glass may shatter and cause injury.

• Do not touch the glass lamp screen. Fingerprints can obscure projection sharpness.

• Be extremely careful when removing the lamp module. In the unlikely event that the lamp ruptures, small glass fragments may be generated. The lamp module is designed to contain most of these fragments, but use caution when removing it.

5 Carefully remove the lamp module by grasping and lifting the metal bail wire. Dispose of the lamp in an environmentally proper manner.

6 Install the new lamp module, making sure that it is properly seated.

7 Tighten the single screw.

8 Replace the lamp door by sliding the tabs into the tab bays and tighten-ing the two screws.

9 Plug in the power cable, then press the Power button to turn the projec-tor back on.

10 Reset the lamp hour timer.

Resetting the lamp timerTo reset the lamp age, simultaneously hold down the two Brightness but-tons on the projector’s keypad for 10 seconds.

Using the security lockThe projector has a security lock for use with a PC Guardian Cable Lock System. See “Accessories” on page 32 for ordering information. Refer to the information that came with the lock for instructions on how to use it.

IR in

1

2

Y Y

Pr Pr

Pb Pb

serial control

M1-DA vesa trigger 1821

3

4

6

5

7

trigger 2

component

s-video

video

D5

component

security lock

32

Appendix

Specifications

Accessories

*country-dependent

Temperature Operating 50 to 95° F (10 to 35° C) at 0 - 7,500 feet

Non-operating -4 to 158° F (-20 to 70° C) at 0 -20,000 feet

Altitude Operating 0 to 7,500 feet (2,286 meters) Non-operating 0 to 20,000 feet (6,096 meters)

Humidity Operating 10% to 95% relative humidity, non-condensingNon-operating 10% to 90% relative humidity, non-condensing

Dimensions 13.8 x 12.8 x 4.3” (351W x 325L x 110H mm)

Weight 9.3 lbs. (4.24 kg) unpacked

Optics Focus Range 5 - 32.8 feet (1.5 - 10 meters)

Lamp Type UHP lamp (dual watt: 200 and 250 watt)

Input Power Requirements 100V-120V 4A, 50/60 Hz200V-240V 2A 50 Hz

Ceiling Mount UL tested/listed ceiling mount with minimum capacity of 46 lbs (20.87 kg)

Standard Accessories(ship with the projector) Part Number

Shipping Box (with packaging) 110-0619-01

Power Cable (country-dependent) 210-0023-xx

Director Remote 590-0567-01

Projection Lamp Module (included in projector)

SP-LAMP-006

Lens Cap 505-1247-xx

User’s Guide 010-0466-xx

Safety Card 009-0659-xx

Cable Cover HW-CABLECVR-001

SCART cable* 210-0249-xx

Optional Accessories Part Number

Shipping Case (ATA approved) CA-ATA-013

Projector Mount SP-CEIL-005

False Ceiling Plate for Projector Mount SP-LTMT-PLT

Extension Arm for Projector Mount 26” - 47”

SP-LTMT-EXTP

30’ Audio/Video Cable SP-AV30

PC Guardian Cable Lock System SP-LOCK

Replacement Lamp Module SP-LAMP-006

North American Power Cable,1m SP-PC-US1M

33

NOTE: Use only approved accessories.

Red LED behavior and projector errorsIf the projector is not functioning properly and the red LED is blinking, con-sult Table 2 to determine a possible cause. There are two second pauses between the blinking cycles. Visit www.infocushome.com/support for more details on the red LED error codes.

Projected image size

NOTE: Visit our website at www.infocushome.com/support for an interac-tive image size calculator.

Table 3: Red LEDs

Red LED Behavior Explanation

One (1) blink The lamp won't strike after five (5) attempts. Check the lamp and lamp door installations for loose connections.

Three (3) blinks The projector has shut down the lamp. Turn off the projector, wait one minute, then turn it back on. Replace the lamp if the projector does not turn on. Contact Technical Support for repair if replacing the lamp does not solve the problem.

Four (4) blinks The fan has failed. Replace the lamp (the lamp module contains a fan). Contact Technical Support for repair if replacing the fan does not solve the problem.

Five (5) blinks The projector is overheating. Check for a blocked air vent. Contact Technical Sup-port for repair if clearing the air vents does not solve the problem.

Table 4: Range of projection distances for a given screen size

16:9 Screen dimensions (inches/m)

Projection Distance

Screen diagonal(inches/m)

Maximum zoom(feet/m)

Minimum zoom(feet/m)

27x48.69x1.22

55.1/1.4 8.1/2.5 10.2/3.1

34x60.9x1.5

68.8/1.75 10.1/3.1 12.7/3.9

40.5x721.0/1.8

82.6/2.1 12.1/3.7 15.3/4.7

45x801.1x2.0

91.8/2.3 13.4/4.0 17.0/5.1

49x871.2/2.2

99.8/2.5 14.6/4.4 18.5/5.6

52X921.3X2.3

105.6/2.7 15.4/4.7 19.6/6.0

54X961.4X2.4

110.1/2.8 16.1/4.9 20.4/6.2

58X1041.5X2.6

119.3/3.0 17.4/5.3 22.1/6.7

65X1161.7X3

133.1/3.4 19.5/6.0 24.6/7.6

34

Source compatibilityTable 5:

Source Compability

Video Component and RGB HDTV (720p, 1035i, 1080i, 1080p, 1080p-24Hz)DVI/HDCP for digital video and encrypted digital videoComponent EDTV (480p, 576p progressive scan), SECAM: M, Component, Composite and S-Video standard video (480i, 576i, 576i RGB SCART with adapter, NTSC, NTSC M 4.43, PAL: B, H, I, M, N)

Computer Digital and analog PC, Macintosh, 1280x1024 resolution

Communi-cation

USB and RS-232

Table 6: Projector Inputs and Outputs

2-Component (Gold RCA)

HDTV, EDTV, and Standard TV component

1-Component (D5)

HDTV, EDTV, Standard TV, RGB SCART with adapter

2-S-Video Standard Video

1-Composite (RCA)

Standard Video

1-M1-DA VESA HDTV RGB, HDTV component, DVI, computer, and USB

1-HD15 VESA HDTV RGB, HDTV component, computer

1-9-pin Dsub male

RS-232

1-3.5 mm mini jack

IR Repeater (Niles/Xantech compatible)

2-3.5 mm mini jack

1-12v screen drop, 1-12v 4:3 aspect “curtains”

35

Projector dimensions for ceiling mount installations

11.3”288.1mm

2.6”64.9mm

2.3”57.8mm

2.1”53.7mm

12.3”312.7mm

total length with optional cable cover: 16.2” 411.5mm)

dimensions of optional cable cover: 12.4 x 3.9 x 3.2” (315 x 100 x 82mm)

8.5”216mm

8.7”221.4mm

4.3”109.5mm

0.14”3.6mm

36

RS-232 terminal specificationsCommunication configurationTo control the projector from an LCD control panel, connect an RS-232 cable to the serial control connector on the projector and set your computer’s serial port settings to match this communication configuration:

Command formatAll commands consist of 3 alpha characters followed by a request, all enclosed in parentheses. The request can be a read request (indicated by a “?”) or a write request (indicated by 1 to 4 ASCII digits).

A read request format: (AAA?) where

( starts the command

AAA denotes the command

? denotes the read request

) ends the command

A read command returns the range and the current setting, for example:

A write request example: (AAA####) where

( starts the command

AAA denotes the command

#### denotes the value to be written(leading zeros not necessary)

) ends the command

Some commands have ranges, while others are absolute. If a number greater than the maximum range is received, it is automatically set to the maximum number for that function. If a command is received that is not understood, a “?” is returned. With absolute settings, “0” is off, 1-9999 is on. The one exception is the Power command, where 0 is off and 1 is on.

Setting Value

Bits per second 19,200

Data bits 8

Parity None

Stop bits 1

Flow control None

Emulation VT100

Function Command Response

Brightness (BRT?) (0-22, 10)

Lamp hours (LMP?) (0-9999, 421)

Function Command Response

Brightness (BRT10) Sets the brightness to 10

Power (PWR0) Turns power off

Power (PWR1) Turns power on

Power (PWR9999) ?

37

Supported commands

Function Command Range Default

Aspect Ratio ARZ 0-40 = Native1 = 16:92 = 4:33 = Letterbox4 = Natural Wide

1

Auto Chime Enable ACE 0-1 1

Auto Power APO 0-1 0

Auto Source ASC 0-1 1

Blank BLK 0-1 0

Blank Screen BSC 0-20 = black1 = blue2 = white

0

Blue Color Offest BCO 1-63 32

Blue Gain BCG 1-63 32

Brightness BRT 8-252 128

Ceiling CEL 0-1 0

Chroma Detail CDE 8-248 128

Color CLR 8-252 128

Color Space CSM 0-70 = RGB3 = REC6012 = REC7097 = Auto

7

Color Temp TMP 0-20 = 93001 = 82002 = 6500

2

Contrast CON 8-252 128

CCS CCS 0-1 0

Display Messages DMG 0-1 1

Factory Reset (Write only) RST 0-1 n/a

Gamma Table GTB 0-40 = PC1 = Video2 = Film3 = Bright Room 14 = Bright Room 2

2

Green Color Offset GCO 1-63 32

Green Gain GCG 1-63 32

High Power Enable HPE 0-1 0

Horizontal Position HPS n/a n/a

Keystone DKC 2-254 128

Lamp Hours (Read only) LMP 0-32767 0

Lamp Reset LMR 0-32767 0

Luma Detail LDE 8-248 128

Menu MNU 0-1 0

Menu Navigation NAV 0-40 = up1 = down4 = select

n/a

38

Language LAN 0-110 = English1 = French2 = German3 = Spanish4 = Chinese Tradi-tional5 = Japanese6 = Korean7 = Portuguese8 = Russian9 = Norwegian10 = Chinese Sim-plified11 = Italian

0

NTSC 2:2 Pulldown Enable NPE 0-1 0

Noise Reduction Enable NRE 0-20 = Off1 = Auto3 = Manual

8

Noise Reduction Level NRL 8-248 8

Overscan OVS 0-1 0

Phase MSS 0-31 n/a

Power PWR 0-1 0

Power Save PSV 0-1 0

Presets PST 0-20 = User 11 = User 22 = User 3

0

Rear Project REA 0-1 0

Red Color Offset RCO 1-63 32

Red Gain RCG 1-63 32

Skintone Bypass Enable SBE 0-1 1

Source SRC 0-70 = Video 1, M11 = Video 2, VESA2 = Video 3, Com-ponent 13 = Video 4, S-Video 14 = Video 5, S-Video 25 = Video 6, Component 26 = Video 7, Composite7 = Video 8, D5

2

Startup Logo DSU 0-1 1

Tint TNT 8-252 128

Tracking MTS 2148-2248 n/a

Translucent OSD TOE 0-1 1

TrueLife Enable TLE 0-1 1

Vertical Position VPS n/a n/a

Video Standard VSU 0-30 = Auto1 = NTSC2 = PAL3 = SECAM

0

39

Numerics12v triggers 4, 3416x9 4, 13, 20, 22, 234x3 234x3 aspect trigger 4AADC Calibration 29adjusting image 9, 22Advanced menu 25altitude limits 32Aspect Ratio 22Auto Power 27Autosource 27BBlank Screen 28blinking green 11blinking red 11Blue Only 29Ccable box 6cables, optional 32CCS 25Ceiling 27Chime 28Chroma Delay 25Chroma Detail 25cleaning the lens 29CLI commands 37Color Space 26color suppression 25Color Wheel Index 29colors are incorrect 14command line interface commands 37component cable connector 7composite video connector 7computer, connecting 10

connectingcomputer 10power cable 7video device 7

connector panel 4contacting InFocus 17customer service contact information 17DD65 colors 9dimensions of projector 35Display Messages 27DVI connector 7Eerror codes 33FFactory Reset 29Faroudja video proecessing 25Film Mode 25focus 9fuzzy image 17HHDTV 6, 20, 22, 34HDTV sources 25, 26height, adjusting 8High Power 27Horizontal Position 25Iimage

display video 8focussing 9size 5zooming 9

image does not fit screen 13image edges distorted 13image not centered 12image not square 13

40

image offset 5image reversed 14image size matrix 33image sizes 5image torn 15image upside down 14InFocus website 2inputs 34IR repeater 4Kkeystone 9, 22Llamp replacement 30lamp timer, resetting 31lamp won’t turn on 15Language 28LED

blinking green 11blinking red 15solid green 11

LED behavior 11, 33Lens cleaning 29Letterbox 23Luma Detail 25MMain menu 21Maintenance 29menus 21

changing the language 28making translucent 28

NNative 22Natural Wide 23no computer image 16no startup screen 12Noise Reduction 25

Ooffset 5only startup screen appears 16optional accessories 32Overscan 24PPhase 25Picture menu 22Power button 8power cable 7, 10Power Save 11, 28Presets 24projection distance 5, 33projector

adjusting height 8cleaing the lens 29compatible sources 34connecting a video device 7connector panel 4controlling projection screen 4customizing 20dimensions 35displaying a video image 8image sizes 33included items 3inputs and outputs 34LED behavior 11maintaining 29menus 21optimizing images 20optional accessories 32overview 3positioning 5, 8remote control 19replacing the lamp 30resetting lamp timer 31

41

saving settings 24security lock 31setting up 5shutting down 11specifications 32standard accessories 32troubleshooting 11

RRear 27remote control 19replacing the lamp 30resetting the lamp timer 31Resize button 22RS-232

connecting 4, 10RS232

specifications 36Ssecurity lock 31Serial connection 10serial connection 4, 36Service Code 29Service menu 29Settings menu 27shutting down the projector 11Skintone Bypass 25Sleep Timer 28solid green 11solid red 11source compatibility 34Source troubleshooting 12, 16Sources 27specifications 32standard accessories 32Startup Logo 28S-video connector 7

System menu 27Ttemperature limits 32Test Pattern 29Tracking 25Translucent OSD 28triggers 4Troubleshooting 11, 12, 16TrueLife settings 25TV tuner 6VVertical Position 25VESA connector 7video connections 6video images, optimizing 20video processing 25Wwarranty 17website 2Zzoom 9

42

Limited Warranty

Subject to the Limitations, Exclusions and Disclaimers hereof, InFocus Cor-poration (“InFocus”) warrants that the Projector, Lamps and Accessories (hereinafter collectively or individually referred to as “Product” as appro-priate) purchased from InFocus, an InFocus distributor, or an InFocus reseller will conform to InFocus’ specifications and be free from defects in material or workmanship for the respective Limited Warranty period pro-vided below. InFocus does not warrant that the Product will meet the spe-cific requirements of the end-user customer.

If the Product while subject to this Limited Warranty, is defective in material or workmanship during the warranty period, then InFocus, at its option, will REPAIR or REPLACE the Product.

All exchanged parts and Products replaced under this Limited Warranty will become property of InFocus. InFocus’ sole obligation is to supply (or pay for) all labor necessary to repair the Product found to be defective within the Limited Warranty period and to repair or replace defective parts with new parts or, at the option of InFocus, serviceable used parts that are equivalent or superior to new parts performance. Limited Warranty periods are as follows:

• Projector Product Limited Warranty Period (Excluding Lamps): Two (2) years from date of purchase.

• Lamp Product Limited Warranty Periods: From the date of Projector Product purchase, the original installed lamp shall have a 90-day or 500 hours usage Limited Warranty Period, whichever comes first, and replacement Lamps purchased at the time of Projector Product pur-chase will have a 500 hours usage Limited Warranty period.

• Accessory Product Limited Warranty Period: one (1) year from date of purchase.

WARRANTY LIMITATION AND EXCLUSION

THIS WARRANTY SETS FORTH INFOCUS’ MAXIMUM LIABILITY FOR ITS PRODUCT. THIS WARRANTY EXTENDS ONLY TO PRODUCTS PUR-CHASED FROM INFOCUS OR AN INFOCUS AUTHORIZED RESELLER. InFocus shall have no further obligation under the foregoing Limited War-ranty if the Product has been damaged due to abuse, misuse, neglect, smoke

exposure (cigarette or otherwise), accident, unusual physical or electrical stress, unauthorized modifications (including use of an unauthorized mount), tampering, alterations, or service other than by InFocus or its authorized agents, causes other than from ordinary use or failure to prop-erly use the Product in the application for which said Product was intended.

This Limited Warranty excludes Product cleaning, repair, or replacement of plastics due to cosmetic damage and damage as a result of normal wear. Product repair outside of the terms of the Limited Warranty will be on a time and materials basis. Prolonged Product “demonstration” causes unusual Product wear and is not considered normal use under the terms of this Limited Warranty.

The Accessory Product Limited Warranty covers the accessory item only and excludes normal wear. The Lamp Product Limited Warranty excludes expected lamp degradation.

Remanufactured Products and Software Products are exempt from the fore-going Limited Warranty. Please refer to the appropriate Remanufactured Product Limited Warranty or Software Product Limited Warranty for appli-cable Warranty information.

DISCLAIMER OF UNSTATED WARRANTIES

THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLI-CABLE TO THIS PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WAR-RANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE ARE DISCLAIMED. THERE ARE NO WARRANTIES THAT EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF AND THE FOREGOING WARRANTY SHALL NOT BE EXTENDED, ALTERED OR VARIED EXCEPT BY WRITTEN INSTRUMENT SIGNED BY INFOCUS. SOME JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY MAY LAST, SO SUCH LIMITATIONS MAY NOT APPLY TO YOU.

43

Limited Warranty Period

The Limited Warranty periods hereof commence on the date of purchase by the end-user customer. These Limited Warranty provisions shall apply only to the end-user purchaser (first person or entity that purchased a new Prod-uct for personal or business use and not for the purpose of distribution or resale). SOME JURISDICTIONS MAY GRANT YOU CONSUMER RIGHTS WITH MINIMUM WARRANTY DURATION THAT DIFFER FROM THE DURATIONS PROVIDED HEREIN, AND INFOCUS WILL HONOR ALL SUCH CONSUMER RIGHTS.

To Be Eligible For Limited Warranty Coverage

Any person exercising a claim under this Limited Warranty must establish to the satisfaction of InFocus both the date of purchase and that the Product was purchased new. The sales receipt or invoice, showing the date of pur-chase of the Product is the proof of the date of purchase.

To Obtain Warranty Service

During the Limited Warranty period, to exercise this Limited Warranty, the purchaser must first contact 1) InFocus, 2) a service facility authorized by InFocus or 3) the place of original purchase.

InFocus Customer Service – 1-800-799-9911 or techsupport@infocus.com

For Warranty service, the purchaser will be advised to return or deliver the defective Product freight and all fees prepaid, to an InFocus Service Center or to a service facility authorized by InFocus. When returning Product to InFocus, a Return Material Authorization Number (RMA ); is required and must be clearly displayed on the outside of the shipping carton or a similar package affording an equal degree of protection. InFocus or the service facility authorized by InFocus will return the repaired/replaced Product freight prepaid to the purchaser.

Products returned for Warranty service must be accompanied by a written letter that: (i) explains the problem; (ii) provides proof of date of purchase; (II) provides the dealer’s name; and (I) provides the model and serial num-ber of the Product.

Upon request of InFocus Corporation or an authorized repair center for InFocus, proof of legal import must accompany the warranty repair Prod-uct, otherwise the Product must be returned to the place of original pur-chase, to the manufacturer (Purchaser must bear all tax, duty and freight), or the Purchaser must bear charges for the warranty repair.

No repair or replacement of Product or part thereof shall extend the Limited Warranty period as to the entire Product. Warranty on the repair part and workmanship shall only be effective for a period of ninety (90) days follow-ing the repair or replacement of that part or the remaining period of the Product Limited Warranty whichever is greater.

LIMITATION OF LIABILITY

IT IS UNDERSTOOD AND AGREED THAT INFOCUS’ LIABILITY WHETHER IN CONTRACT, IN TORT, UNDER ANY WARRANTY, IN NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE RETURN OF THE AMOUNT OF THE PURCHASE PRICE PAID BY PURCHASER AND UNDER NO CIRCUMSTANCES SHALL INFOCUS BE LIABLE FOR SPE-CIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOST PROFITS, LOST REVENUES OR LOST SAVINGS. THE PRICE STATED FOR THE PRODUCTS IS A CONSIDERATION IN LIMITING INFOCUS’ LIABILITY.

Limitation on Bringing Action - No action, regardless of form, arising out of the agreement to purchase the Product may be brought by purchaser more than one year after the cause of action has accrued.

Governing Law - Any action, regardless of form, arising out of the agree-ment to purchase the Product is governed by Oregon law.

Mandatory Arbitration – Any action, regardless of form, arising out of the agreement to purchase the Product is subject to mandatory arbitration.

SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, DEPENDING ON JURISDICTION.