ENGINEERING DRAWING Topic: Sectioning
Transcript of ENGINEERING DRAWING Topic: Sectioning
![Page 1: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/1.jpg)
ENGINEERING DRAWING
Topic: Sectioning
https://www.youtube.com/watch?v=K_2uJPkCv0Y
![Page 2: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/2.jpg)
Sectioning
The detail of an object can be shown by drawing a limitednumber of carefully chosen views and showing externalfeatures of the object by firm lines and invisible detail byhidden lines.
But when the interior of the object is complicated then themethod of showing interior details by hidden lines makes theview confusing and hard to read.
![Page 3: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/3.jpg)
Sectional View
In such cases the object is assumed to becut by an imaginary plane from aparticular section.
The part of the object in between theobserver and the cutting plane is removedto expose the hidden detail of the object.
The cut surfaces are identified by drawingsection lines and the view thus obtained iscalled the “Sectional View” or “View inSection” of the remaining object.
Section lines
Sectioning
![Page 4: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/4.jpg)
Purpose of Sectioning
To clarify the internal detail of the object by reducing oreliminating the hidden lines from the view.
Sectional Front ViewFront View
![Page 5: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/5.jpg)
Terminology
Cutting Plane:It is a plane that imaginarily cuts the object to reveal theinternal features.
Cutting Plane
![Page 6: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/6.jpg)
Terminology Cutting Plane Line:
It is an edge view of the cutting plane used to indicate wherethe imaginary cutting of the object takes place.
![Page 7: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/7.jpg)
Terminology Section Lines:
In a sectional view, wherever the material has been cut by thecutting plane, to make the cut surface distinct, a conventionalscheme called section lines or cross hatching is employed.
Section lines
![Page 8: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/8.jpg)
Terminology Section Lines:
Section lines are different for each of material’s type.
For practical purpose, the case iron symbol is used mostoften for any materials.
Cast iron
Steel
Concrete
Wood
![Page 9: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/9.jpg)
Terminology
Cast iron1. 45o angle with horizontal2. Equidistant (2-3 mm gap)3. Parallel lines
Section Lines:
Section lines are different for each of material’s type.
For practical purpose, the case iron symbol is used mostoften for any materials.
![Page 10: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/10.jpg)
Terminology Section Lines:
Lines should never be parallel or perpendicular to object lines. If the object line is at 45o then, 30o or 60o angle can be used
for section lines.
![Page 11: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/11.jpg)
Treatment of hidden lines
Hidden lines are normally omitted from the section views.
![Page 12: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/12.jpg)
Types of Section
Full Section Half Section Offset Section
![Page 13: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/13.jpg)
Full Section
When the cutting plane passesentirely through the object, in astraight line the view obtained iscalled full section of the object.
If the object is symmetric thenthis method will divide theobject into two identical parts.
Full Section View
![Page 14: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/14.jpg)
Full Section
When the object is sectionedalong its length, it is called a
longitudinal section.
Full Section View
(Longitudinal Section)
![Page 15: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/15.jpg)
Full Section
When the object is sectionedcrosswise, the section is called a
cross section.
Full Section View
(Cross Section)
![Page 16: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/16.jpg)
Half Section
In symmetrical objects, to showthe interior and exterior detailsin the same view, half sectionsare drawn.
Two cutting planes (90O to eachother) are used to cut the objectfrom two center lines to removequarter portion of the object.
Half Section View
![Page 17: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/17.jpg)
Half Section The hidden lines may be omitted
in both halves of the view,unless they are needed fordimensioning.
The two parts of the half sectionview are separated only by thecenter line as the object is onlyimagined to be cut and no actualcutting edge exists.
Half Section View
![Page 18: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/18.jpg)
Off-set Section
In full section, the cutting planeis usually taken straight and ismade to pass through the centerof the object.
![Page 19: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/19.jpg)
Off-set Section
In full section, the cutting planeis usually taken straight and ismade to pass through the centerof the object.
But in some objects, when thiscutting plane does not exposethe required details, or it passesthrough features which shouldnot be sectioned, it is off-set bychanging the direction and ismade to pass through requireddetails that need to be shown insection.
For this purpose two or morecutting planes are used.
![Page 20: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/20.jpg)
Ribs It is a thin plate that acts as a support for other plates and
provides rigidity to the object.
Rib
![Page 21: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/21.jpg)
Ribs Section lines are not placed in the ribs even if they are cut by
the cutting plane.
![Page 22: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/22.jpg)
Ribs Section lines are not placed in the ribs even if they are cut by
the cutting plane.
Otherwise these would give the false impression that thepart is thicker than it really is.
![Page 23: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/23.jpg)
Ribs Section lines are not placed in the ribs even if they are cut by
the cutting plane.
Otherwise these would give the false impression that thepart is thicker than it really is.
![Page 24: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/24.jpg)
Practice
![Page 25: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/25.jpg)
Practice
![Page 26: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/26.jpg)
Practice
![Page 27: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/27.jpg)
Practice
![Page 28: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/28.jpg)
Practice
![Page 29: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/29.jpg)
Practice
![Page 30: ENGINEERING DRAWING Topic: Sectioning](https://reader030.fdocuments.net/reader030/viewer/2022013001/61ca5909939cc57e5e064a45/html5/thumbnails/30.jpg)
Thanks