EML 2023 – Modeling, Assemblies
description
Transcript of EML 2023 – Modeling, Assemblies
![Page 1: EML 2023 – Modeling, Assemblies](https://reader036.fdocuments.net/reader036/viewer/2022081506/56814ab1550346895db7c3c2/html5/thumbnails/1.jpg)
EML 2023 – Modeling, Assemblies
Lecture 3.2 – Assemblies, part 2
![Page 2: EML 2023 – Modeling, Assemblies](https://reader036.fdocuments.net/reader036/viewer/2022081506/56814ab1550346895db7c3c2/html5/thumbnails/2.jpg)
2
Final Assembly
• The final assembly will include the previous sub-assembly.
• Pilot holes will be drilled into the frame at the assembly level, not at the part level as was done with the hatch.
![Page 3: EML 2023 – Modeling, Assemblies](https://reader036.fdocuments.net/reader036/viewer/2022081506/56814ab1550346895db7c3c2/html5/thumbnails/3.jpg)
3
sub-assembly
![Page 4: EML 2023 – Modeling, Assemblies](https://reader036.fdocuments.net/reader036/viewer/2022081506/56814ab1550346895db7c3c2/html5/thumbnails/4.jpg)
4
We will line up the hatch and the frame by mating the right plane of the assembly with the right plane of the hatch part.
If the hatch part was not built as being symmetric with respect to the right plane, an offset distance mate could be used to center the hatch sub-assembly.
![Page 5: EML 2023 – Modeling, Assemblies](https://reader036.fdocuments.net/reader036/viewer/2022081506/56814ab1550346895db7c3c2/html5/thumbnails/5.jpg)
5
Mate the back face of the hinge to the front face of the frame. Offset the top face of the hinge 2” from the top face of the frame.
![Page 6: EML 2023 – Modeling, Assemblies](https://reader036.fdocuments.net/reader036/viewer/2022081506/56814ab1550346895db7c3c2/html5/thumbnails/6.jpg)
6
Mate the hinge faces. Mate the cylindrical edges as concentric.
![Page 7: EML 2023 – Modeling, Assemblies](https://reader036.fdocuments.net/reader036/viewer/2022081506/56814ab1550346895db7c3c2/html5/thumbnails/7.jpg)
7
Pilot Holes• Time to make the pilot holes in the frame.
– make a sketch in the front plane of the frame– put points at the center of the hinge holes– hide the hinge and add four circles centered on the four
points with diameter of 0.2 inches– close sketch and cut a depth of 0.65”
Insert Assembly Feature Cut Extrude
![Page 8: EML 2023 – Modeling, Assemblies](https://reader036.fdocuments.net/reader036/viewer/2022081506/56814ab1550346895db7c3c2/html5/thumbnails/8.jpg)
8
Can check for interference detection.
![Page 9: EML 2023 – Modeling, Assemblies](https://reader036.fdocuments.net/reader036/viewer/2022081506/56814ab1550346895db7c3c2/html5/thumbnails/9.jpg)
9
![Page 10: EML 2023 – Modeling, Assemblies](https://reader036.fdocuments.net/reader036/viewer/2022081506/56814ab1550346895db7c3c2/html5/thumbnails/10.jpg)
10
![Page 11: EML 2023 – Modeling, Assemblies](https://reader036.fdocuments.net/reader036/viewer/2022081506/56814ab1550346895db7c3c2/html5/thumbnails/11.jpg)
11
Top level only BOM.
![Page 12: EML 2023 – Modeling, Assemblies](https://reader036.fdocuments.net/reader036/viewer/2022081506/56814ab1550346895db7c3c2/html5/thumbnails/12.jpg)
12
Top level only BOM.
![Page 13: EML 2023 – Modeling, Assemblies](https://reader036.fdocuments.net/reader036/viewer/2022081506/56814ab1550346895db7c3c2/html5/thumbnails/13.jpg)
13
Parts only BOM.
![Page 14: EML 2023 – Modeling, Assemblies](https://reader036.fdocuments.net/reader036/viewer/2022081506/56814ab1550346895db7c3c2/html5/thumbnails/14.jpg)
14
Parts only BOM.