EM-176 DC-MOTOR CONTROLLER 12/24Vdc · PDF fileEM-176 DC-MOTOR CONTROLLER 12/24Vdc 10A...
Transcript of EM-176 DC-MOTOR CONTROLLER 12/24Vdc · PDF fileEM-176 DC-MOTOR CONTROLLER 12/24Vdc 10A...
EM-176 DC-MOTOR CONTROLLER12/24Vdc 10A
FEATURES:
• 4 Quadrants• Braking• Freewheeling• Reversal• 0...10V control• Optional ±10V control• Soft start ramp• Adjustable current limit• Load compensation ( RxI )• High efficiency• High peak loading capacity• Rail mountable
EM-176 is designed for DC-motor speed control. The unit can be used with unregulated DC supply. Motorloading can be compensated with inbuilt RxI-type adjustment. EM-176 utilizes PWM driven H-bridge, thusachieves high efficiency and extensive controlling options. Speed control value can be set with voltage signalor with potentiometer, there is an auxiliary voltage signal output for potentiometer use. The scale trimmer canbe used to scale set value to correspond better the motor rpm. An auxiliary card can be fitted into EM-176 forbipolar input controlling with voltage signal or potentiometer. The ramp feature is used to limit the motor startand brake speed, in other words soften the operation and prevent the occurrence of current spikes. Thecurrent limit limits motor torque that is current; this protects the motor and the mechanics. The unit hasseparate inputs for brake, freewheel and reverse. Brake short-circuits the motor poles and produces powerfulbraking. Freewheel detaches the power stage from the motor and leaves motor rotating freely. Reversechanges motor rotating direction, this is done using the set ramp times.Brake and freewheel bypass the ramp feature.
TECHNICAL DATA:
SupplyOver voltage protectionIdle currentMotor current
Motor voltageCurrent limitCurrent lim. volt. ctrlRamp timeVoltage lossOperating freq.Aux. voltagesSet value range
Set value input imp.Control voltage
Control input imp.
Operating temp ( Ta )MeasuresWeight
12-35Vdc39Vappox. 30mA10A cont. ( Ta<50°C )15A peak ( 20% on/ 80% off )0-29V ( 0-100%)adj. 0...15A0...5V ( 0...15A )adj. 0...3s1.2V ( Im=10A )25kHz+5V 10mA ( option -5V )0...5 or 0...10V ( ±5V or ±10V option )100kohm ( pin 7 and 9 )"on" when Uin 4 -30V"off" when Uin 0-1V or open10kohm ( pin 5, 6 and 8 )
-20...+7065x73x30mmapprox. 100g
CURRENTANDVOLTAGECONTROL
EM-176 BLOCK DIAGRAM
BRAKE
CURRENT SET
CURRENT LIMIT
7
4
5
DIR
RANGESCALE
SPEEDSET
5V/ 10mA
9
8
6
10
FREEWHEEL
RxI
RAMP
EM-A1bipolarcard
optional
MOTOR-CURRENTMEAS.
Im
+
POWERSTAGE
Um
VOLTAGEREG.
-
2
M
3
SUPPLY
4
1100R
Recom. control pot. 4.7...47k
Vähäheikkiläntie 56B, 20810 Turku, FINLAND Tel. +358-2-4693050 Fax. +358-2-4693052ELECTROMEN Oy
INSTALLATION EM-176
Supply voltage 12-35VDC, ripple <30% at full load.CAUTION ! Wrong polarity may damage the device.CAUTION ! The device is not equipped with aninternal fuse.
SETTINGS AND ADJUSTMENTS
Set trimmers in center position. Current limit can be setin the range of 0-15A. If an external voltage signal (0-5V) or potentiometer is used to set the current limit, setthe inbuilt current limit trimmer to 0-position.
The compensation (RxI) is used as follows: first set themotor running slowly. Then increase compensationuntil the motor starts twitching. Now decreasecompensation a little so that the twitching ends. Finallytest the operation: when loading the motor, the rotationspeed should almost remain constant.
The acceleration- and braking ramp are set withtrimmers in the range of 0-3s (the time from zero to fullspeed or vice versa). The speed can be set withpotentiometer or with 0-5V voltage signal. With the setvalue trimmer the set value range can be scaled tomatch the motor rotating speed range.
If the use of bipolar control signal is desired, anauxiliary card EM-A1 can be fitted onboard, whichmakes it possible to use either ±5V or ±10V controlvoltage signals. EM-A1 card also gives -5V auxiliaryvoltage into pin8; this enables potentiometer to be usedto control both speed and direction (forward-stop-reverse).
EM-176 WIRING AND INSTALLATION
EXAMPLE 2
CONTROLLING WITH VOLTAGES.
CURRENT 0-5V CORRESPONDS TO 0-15A.CURRENT LIMIT TRIMMER IS SET TO MIN.
SPEED 0-5V CORRESPONDS TO 0-100%SPEED. SCALE WITH TRIMMER.
DIRECTION, FREEWHEEL OR BRAKE0-1V OR OPEN=OFF, 4-30V=ON.
EXAMPLE 1
CONTROLLING WITH SWITCHES.SPEED SET WITH POTENTIOMETER.SPEED RANGE ADJUSTABLE WITHSPEED SET RANGE ADJUSTMENT.
CURRENT LIMIT CAN BE SET WITHINBUILT TRIMMER. IF EXTERNALADJUSTMENT IS USED, SET THEINBUILT CURRENT LIMIT TRIMMERTO MINIMUM.
EXAMPLE 3 (OPTIONAL)
EM-A1 BIPOLAR-CARD INSTALLED.
CONTROLLING WITH POTENTIOMETERFORWARD/REVERSE OR WITH VOLTAGESIGNAL (±5V OR LARGER BIPOLARVOLTAGE). RANGE ADJUSTABLE WITHRANGE SCALE TRIMMER ADJUSTMENT.
OTHER CONTROLS AS IN PREVIOUSEXAMPLES.
10
BR
AK
EGN
D 0
V
4 5
FRE
EW
H.
6 7
CU
RR
EN
T
98
+5V
10
DIR
.
SP
EE
D
Im Um
BR
AK
E
54
GN
D 0
V
FRE
EW
H.
CU
RR
EN
T S
ET
DIR
.
SP
EE
D
+5V
9876
REVERSE / FORWARDPOT. IN THE MIDDLE=STOP
10
BR
AK
E
FRE
EW
H.
5
GN
D 0
V
4 9
-5V
876
+5V
SP
EE
D+D
IR.
EM-A1 card slot,normally 2 jumps
set valuescaleV / 0-100%
BR
AK
ECAUTION !Wrong polarity can damage the device.Select a fuse (1-16A) in accordancewith the application.
+12-
32V
MOTOR
321S
UP
PLY
DC-
-+
4
GN
D 0
V
72m
m
66m
m
10
0-5V
SP
EE
D S
ET
5 6 7 8 9
DIR
.
+5V
CU
RR
. SE
T
FRE
EW
H.
min
max
15
59mm
65mm
8
0-10
0-24V
0
3ramp / s
1
2
Motorloadcompensation
0current lim / A
4