Elevator Assembly 1 - LaMiaStampante.it...C4724-60053 2 C4724-60053 Description X-Axis motor...
Transcript of Elevator Assembly 1 - LaMiaStampante.it...C4724-60053 2 C4724-60053 Description X-Axis motor...
Ref 1
2
3
4
5
6
7
Part Number C4704-60022
C4704-60021
C4724-60021
C4704-60056
C4723-60114
C4704-00033
C4704-60274
Description Ribbon cable for one IDE drive - Has 40-pin (F) connectors - 31.8cm (12.5in) long - Data cable from drive to main board Hard drive power cable - Has 4-pin (F) connectors - 47.6cm (18.8in) long - From drive to main board
4.3GB hard disk drive - Mounts in the Electronics Enclosure
Power switch - Includes cable
Electronics module - Includes power supply, fan, and main board (ohne Liefertermin)
SIMM slot cover
Electronics module cover - Mounts to rear of plotter - Includes SIMM cover
Elevator Assembly 1
Ref 1
Part Number C4704-60033
Description Elevator platform assembly - Raises and lowers ink cartridges to fll the print heads - Located on left side of plotter
Entry Platen Area
2
1
5
3
4
6
Carriage Assembly 6
2
1
7
5 3
4
Ref Part Number
1 2
3
4 5
6 7
C4723-60237 C4704-40085
C1633-80014
C4704-40084 C4704-60117
C4723-69096* C4704-40080
Description Carriage assembly trailing cable - Three ribbon cables bundled together - 2.4m (7.7ft) long - From carriage board to main board (DesignJet 3000CP Trailing cable clamp - Secures the trailing cable to the carriage assembly
Compression spring - For the rear bushing on the carriage
Rear slider rod bushing - Spring loaded - Rear slider rod bushing - Spring loaded - Slides into the rear center of the carriage assembly Line sensor lens cover - Mounts to carriage assembly
Carriage assembly - Includes carriage assembly, line sensor, encoder, rear bushing, calibration pen, digiti- zing sight, guages - Trailing cable and cable clamp not included Encoder strip roof - Mounts in carriage assembly over the encoder strip
Electronic Modul 4
3
5
1 2
6
* Artikel sind obsolete, ohne Ersatz 7
Ref 1
2
3
4
5
6
7
Part Number C4704-60022 C4704-60021
C4724-60021 C4704-60056
C4723-60114
C4704-00033
C4704-60274
Description Ribbon cable for one IDE drive - Has 40-pin (F) connectors - 31.8cm (12.5in) long - Data cable from drive to main board Hard drive power cable - Has 4-pin (F) connectors - 47.6cm (18.8in) long - From drive to main board
4.3GB hard disk drive - Mounts in the Electronics Enclosure Power switch - Includes cable
Electronics module - Includes power supply, fan, and main board (ohne Angabe von Lieferzeit)
SIMM slot cover
Electronics module cover - Mounts to rear of plotter - Includes SIMM cover
Elevator Assembly 1
Ref 1
Part Number C4704-60033
Description Elevator platform assembly - Raises and lowers ink cartridges to fll the print heads - Located on left side of plotter
Entry Platen Area 2
1
4
3 5
Ref 1
2
Part Number C4723-60279 C4704-60143 C4713-60035 C4723-60246
C4704-60195 C4723-60250
3
4 5
Description Bail assembly - Mounting strip assembly for the starwheel mount assemblies (Not included) - Extends width of plotter Big starwheel mount assembly - Includes cover, body, spring and two starwheels - (Two used) mounts on the bail assembly (Note: part number is for one starwheel mount assembly ONLY) Starwheel mount assembly - Includes cover, body, spring and two starwheels - (11 used) mounts on the bail assembly (Note: part number is for one starwheel mount assembly ONLY) Entry platen assembly - Cover/guide that is next to the paper drive (platen) roller
Media sensor assembly - Media sensor assembly - Includes, edge measuring and secondary levers, media sensor and holder Starguard starwheel cover assembly
Left Hand Cover Area 1
2
3
Ref 1
2
3
Part Number C4723-60111
C4723-60116*
C4704-60058
Description Left trim assembly - At left of entry platen
Left end cover
Left end cover sensor - Includes cable and connector - Left end cover sensor - Includes cable and con- nector - Plugs into refll interconnect board
Media Button and Media Guide
2
1
* Artikel sind obsolete, ohne Ersatz
Ref 1
2
Part Number C4723-60110 C4723-60017
Description Media guide bar - Mounts above the entry platen (The media load button mounts on the right end of the bar) Media load switch assembly - Mounted on media guide
Paper Drive Roller Area 5
7 4
6
3
3
1 2
3
Ref 1
2
3
4
5
6
7
Part Number Description
C4704-40026
C1633-40019 C4723-60234 C4723-60242
C4723-60247 C1633-80005
C1633-40082
Roller support bracket - Roller support bracket on left side plate - Installed on left side plate
Overdrive gear cluster - Cluster gear - Mounts to the left side plate of the plotter - Between the paper drive roller gear and the overdrive gear
Overdrive assembly - Includes overdrive shims, clutch and overdrive gear - Mounted between the left and right side plates of the plotter below bail assembly
Paper drive (platen) roller assembly - Long gear driven roller
Pincharm assembly - Curved black plastic plate with four small rubber rollers - Does NOT include spring or bushing - (11 used)
Compression spring - Installed between pincharm assembly and bushing - 11 used
Pincharm spring retaining bushing - Bushing - Retains spring on shaft of pincharm assembly
Pinch Arm Assembly 2 2
6
5
4
3 1
Ref 1
2
3
4
5
6
Part Number C4704-60052
C3190-60149
C4723-00025
Description Pincharm sensor - Pincharm sensor - Mounted on right side plate
Left cam journal - Mounted on left end of pinch arm shaft - (Two used)
Front wire link - Connected from pinch arm cam to spring loaded cam on right side plate of printer
C3180-40020* Pinch arm cam - Attached to pinch arm (Media) lever C4704-40059* Pinch arm (media) lever - Used when loading paper
C4723-60240 Pincharm shaft assembly - Includes cam journals mounted on each end - Pincharm shaft assembly - Le- ver actuated shaft that releases the pincharms - Includes cam journals mounted on each end
Printer Rear 9
8 10
12
4
7 13 3
6 5
1 11 2 * Artikel sind obsolete, ohne Ersatz
Ref 1
2
3
Part Number C4704-40058
C4704-40057
C4704-69343* C4723-69294 1818-6171*
1818-6172*
C4723-60263
C4723-60264
C4723-60114
J4100-69001 C4723-60025* C4723-60237 C4723-40086
C4723-60290 C4723-20008
C4723-00010
C4704-00033
4
5 6 7 8 9
10 11
12
13
Description Electronics module right cover - Mounts on rear of plotter
Electronics module left cover - Louvered cover on rear of plotter
PostScript SIMM kit - Version 8.1.01 - Installed in the electronics module - NOTE: This is not the frm- ware SIMM (DesignJet 3500CP) Firmware SIMM kit (Revision A.04.08) - Mounts in the electronics module - NOTE: this is not a post- script SIMM 4MB EDO (Extended Data Output) DRAM SIMM memory module - (C6229A)
8MB EDO (Extended Data Output) DRAM SIMM memory module - (C6230A)
8MB EDO (Extended Data Output) DRAM SIMM memory module
16MB, 60nS EDO (Extended Data Output) DRAM SIMM memory module - (C6231A)
Electronics module - Includes power supply, fan, and main board (Ohne Angabe von Lieferzeit)
JetDirect 400N modular input/output (MIO) internal print server - Provides 10/100Base-TX or 10Base-2 network connection using RJ45 or BNC connectors - (J4100A) Ribbon cable assembly with ferrite - Has 28-pin (F) connectors - 1.7m (5.6ft) long - From refll inter- connect board to main board Carriage assembly trailing cable - Three ribbon cables bundled together - 2.4m (7.7ft) long - From carriage board to main board Trailing cable holder
Electronics support frame and cover supports - Includes the support located above the refll intercon- nect cable and the two supports used to mount the rear cover Electronics module center cover - Located between electronics module cover and rear cover
Rear cover - Located next to electronics module cover
SIMM slot cover
Printer Support
5 1
7
3
4
6
9
8
2
10
* Artikel sind obsolete, ohne Ersatz
Ref 1
2
3
4
5
6
7
8
9
Part Number Description
C4723-60095
C4723-60086
C4704-60075
C4723-60084
C4723-60077
C6246-60009
C4723-60072 C4723-69071
Hardware kit - Includes screwdriver and screws for printer stand
Foot assembly (includes casters) - Mounts to the bottom of the plotter stand legs (two used)
Leg assembly - Side support for the plotter - Does NOT include the foot assembly - (Two used)
Plotter stand tray assembly - Plotter stand tray assembly - Mounted between the feet of plotter
Cross-brace - Brace that connects and supports the two stand legs
Take-up reel support assembly - Take-up reel right hand support assembly - Mounted on right leg
Take-up reel left hand support assembly - Take-up reel left hand support assembly - Mounted on left leg
Take-up reel sensor assembly - Take-up reel sensor assembly - Mounted near bottom of right leg
C4723-60064* Take-up reel spindle assembly
Refll Assembly
2
1
Description
Refll assembly - Mounted inside the left hand cover - Includes motor and gears
Left end cover sensor - Includes cable and connector - Left end cover sensor - Includes cable and con- nector - Plugs into refll interconnect board
Ref 1
2
Part Number C4723-60249
C4704-60058
Refll Interconnect Board, Bail Motor and Cutter Assemby
4
1 3
2
Ref 1
2
3
4
Part Number C4704-60009
C4723-60040
C4723-60244
C3195-40076
Description Refll interconnect board - Refll Interconnect Board - Mounted on Left Side Plate of Plotter
Bail motor - Mounted on left side plate
Cutter assembly - Auto cutter for rollfeed paper
Cutter bushing - Connects cutter assembly to slider rod - Bushing - Attaches to rear of cutter assembly - Connects cutter assembly to slider rod
* Artikel sind obsolete, ohne Ersatz
Right Hand Cover Area 5
2 4
7
1
6
3 Description
Right trim assembly - At right of entry platen
Right end cover - Has cut outs for the control panel
Right end cover and window closed sensors - Includes cable and connector - Right end cover and win- dow closed sensors - Includes cable and connector - Plugs into front control panel
Lift-up viewing window - Located on top of chassis
Quick reference holder pocket - Holds quick reference guides and media knife - Mounted on rear of right end cover
Front (Control) panel and cable assembly - Includes function buttons and display
Stand-by switch asembly - Mounted in right end cover
Ref 1
2
3
4
5
6
7
Part Number C4704-60113
C4723-60115
C4704-60029 C4723-60236*
C4704-60218 C4704-60255
C4704-60261
Roll Cover Area 5
2
3
1
6
4
* Artikel sind obsolete, ohne Ersatz
Ref
1
2 3
4
5
6
Part Number
C4723-60241 C4723-80021 C4723-60245
C4704-60082 C4704-60199 C2858-40043
Description
Rollfeed spindle rod assembly - Includes flange and core spindle spacer Extension spring - Holds the rollfeed access cover closed - One used on each end of the cover Rollfeed access cover - Opens forward to allow access to paper spindle assembly
Housing assembly (on left side) - Accepts the left side (end with smaller end cap) of the paper spindle assembly
Brake/housing assembly (on right side) - Accepts the flange end of the spindle rod assembly - Includes the 2 housing pieces, 2 brake shoes, brake gear, brake lever, and springs
Spindle end cap - Small core spacer - Removes for loading the media roll - Removes for loading the media roll
Service Station Assembly 5 1
4
3
2
Ref
1
2
3
4
5
Part Number
C4704-60024 C4723-60276
C4723-60276 C4704-80009
C4704-40007
Description
Ribbon cable assembly - Has 28-pin (F) connectors - 23.5cm (9.3in) long - From service station inter- connect board to main board
Service station assembly - Mounted on right side of plotter - Holds the print head cleaner cartridge
?
Service station spring - Mounted on right side of service station - Attached to service station flag
Service station flag - Spring loaded flag on right side of service stati
X-Axis Motor Assembly
1
2
Ref 1
Part Number C4724-60053
2 C4724-60053
Description X-Axis motor assembly kit - New design does not use a belt - Kit includes motor with attached worm gear, helical gear, motor mount, screws and nuts for mounting the parts, grease for the helical gear, installation instructions X-Axis motor assembly kit - New design does not use a belt - Kit includes motor with attached worm gear, helical gear, motor mount, screws and nuts for mounting the parts, grease for the helical gear, installation instructions
Y-Axis Assembly (1 of 3) Belt, Tensioner, Pulley and Encoder
3
2
1
4
Ref 1
2
3
4
Part Number C4723-60232
C4704-60020
C4723-60235 C4723-60063
Description Encoder strip - Used to determine carriage position - Connects from left to right side of plotter
Idler pulley - For carriage (Y-axis) belt - On right end of plotter
Carriage (Y-axis) belt - Drives the carriage assembly Y-axis tensioner assembly - Applies tension to carriage belt - Includes wedge, tensioner spring, and housing
Y-Axis Assembly (2 of 3) Belt, Encoder Strip, Hardware
5
1
4
2 3
Ref 1
2
3
4 5
Part Number C4704-00016
C4699-00016
C4723-60232 C4723-60235 9170-1687
Description Encoder ground strap - Provides ground to end of encoder strip
Encoder spring - Mounted under encoder strip on right encoder bracket
Encoder strip - Used to determine carriage position - Connects from left to right side of plotter Carriage (Y-axis) belt - Drives the carriage assembly Ferrite core - Installed on Y-AXIS motor cable
Y-Axis Assembly (2 of 3) Belt, Encoder Strip, Hardware
3
2
1
4
Ref 1
2
3
4
Part Number C4704-00005
C4704-00035
C4723-60277 0460-2536
Description Y-axis motor bracket - Includes edge wire saddle - Holds the Y-Axis motor
Ground strap - Attached to Y-AXIS bracket
Carriage (Y-Axis) motor assembly - Drives carriage belt - Includes motor, motor holder, and cable Edge wire saddle for Y-axis bracket