ELEVATION™ X 36 DIRECT VENT GAS FIREPLACE · 2020. 4. 4. · 22 1/2” 22” 8” 1” 8” 5”...
Transcript of ELEVATION™ X 36 DIRECT VENT GAS FIREPLACE · 2020. 4. 4. · 22 1/2” 22” 8” 1” 8” 5”...
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 0G8 Canada • 1(866)820-8686 • www.napoleon.com
Do not put objects in front of the appliance(minimum distance of 4 feet)*
38 3/4”OVERALL
33 1/8”*F.O.
36”*FIREPLACE OPENING
44”OVERALL
43 1/2”HEADER
22 1/2” 22”
8”
1”
8” 5”
35 1/8”
TOP VIEW FRONT VIEW RIGHT SIDE VIEW
30 1/2”
Gas inlet
ELEVATION™ X 36 DIRECT VENT GAS FIREPLACE
W415-2776 / A / 03.13.20
Specifi cations
Model BTUWidth Height Depth
Glass SizeActual Framing Actual Framing Actual Framing
EX36NTEL 37,00038 3/4” 39 3/4” 44” 43 3/4” 22” 22 1/4” 27” x 32 1/4”
EX36PTEL 34,000
Dimensions
Appliance Location
SIDE WALL
6”
Combustible Mantel Clearances
MLK
J
TOP OFFIREPLACE OPENING
MANTEL DIMENSIONS
Ref Height Depth
J 15” 2”
K 17” 4”
L 19” 6”
M 21” 8”
75 1/2”
53 3/8”
39 3/4”
22 1/4”
*
* Finishing flange (the finishing flange defines the perimeter of the fireplace opening. Framing or finishing materials must NEVER encroach inside the finishing flange).
*
Mantel clearances can be reduced with DHC™ kit (see DHC™ manual for installation instructions).
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 0G8 Canada • 1(866)820-8686 • www.napoleon.com
Firestop assembly
Non-combustiblematerial
1" [25mm]
0” [0mm] if non-combustible finishing material is used such as brick and stone.
Insulated sleeve
3"[76mm] to top
2"[51mm] to
sides / bottom
Non-combustible
Brick
Combustible1" [25mm] minimum all sides for vertical venting sections.When passing through a ceiling, use firestop W500-0028 (not supplied).
4"min.
12"[305mm]* 72"
(182.8cm)min.
10 1/4"
ELEVATION™ X 36 DIRECT VENT GAS FIREPLACE
Product information provided is not complete and is subject to change without notice. Please consult the installation manual for the most up to date installation information.
W415-2776 / A / 03.13.20
Wall Penetration
59”plus rise
Vent SectionsWhen passing through a wall, use fi restop spacer W010-1800 (supplied). When passing through a ceiling, use fi restop spacer W500-0028 (not supplied).
note:
Horizontal vent sections: A minimum clearance of 3” (76mm) on the top of the vent to combustibles and 2” (51mm) on the sides and bottom of the vent to combus-tibles is required.
Vertical vent sections: A minimum clear-ance of 1” (25mm) all around the vent pipe on all vertical runs to combustibles is required.
Flush Finish Framing Recessed Finish Framing
Framing
72”(183cm)
min.
39 3/4”
43 3/4”
72”(183cm)
min.Recessed
volume must be added to
the overall size of the
enclosure.
39 3/4”
Max. 5 1/2”
43 3/4”
* Recess frame can be “backed” with 3/4” ply to support TV mounting hardware.
* The minimum enclosure height is deter-mined based on volume of air needed in the enclosure.
22 1/4”22 1/4”
6” min.
6” min.
6” min.
6” min.
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 0G8 Canada • 1(866)820-8686 • www.napoleon.com
Do not put objects in front of the appliance(minimum distance of 4 feet)*
6”
75 1/2”
53 3/8”
39 3/4”
22 1/4”
38 3/4”COMPLET
33 1/8”*F.O.
36”*OUVERTURE DE FOYER
44”COMPLET
43 1/2”EN-TÊTE
22 1/2” 22”
8”
1”
8” 5”
35 1/8”
30 1/2”
Entrée de Gaz
FOYER À GAZ VENTILÉ DIRECTE ÉLÉVATIONMD X 36
W415-2776 / A / 03.13.20
Spécifi cations
Modèle BTULargeur Hauteur Profondeur
Taille de verreRéel Ossature Réel Ossature Réel Ossure
EX36NTEL 37,00038 3/4” 39 3/4” 44” 43 3/4” 22” 22 1/4” 27” x 32 1/4”
EX36PTEL 34,000
Dimensions
Emplacement de l’Appareil
MUR DE CÔTÉ
Dégagements Combustible de la Tablette
MLK
J
TOP OFFIREPLACE OPENING
DIMENSIONS DE LA TABLETTE
Réf Hauteur Profondeur
J 15” 2”
K 17” 4”
L 19” 6”
M 21” 8”
VUE DE FACE VUE DE CÔTÉ DROIT VUE DE DESSUS
Ne placez pas de l’objets en avant de l’appareil (distance minimum de 4 pieds) *
DESSUS DE L’OUVERTURE DE L’APPAREIL
ARRIVÉE DE GAZ
*
*
* La bride de finition (la bride de finition définit le périmètre de l’ouverture de l’appareil. Les matériaux d’ossature ou de finition NE JAMAIS empiété à l’intérieur de la bride de fintion).
Les dégagements de la tablette peuvent être réduits avec le kit DHC™ (voir le manuel DHC™ pour les instructions d’installation).
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 0G8 Canada • 1(866)820-8686 • www.napoleon.com
Firestop assembly
Non-combustiblematerial
1" [25mm]
0” [0mm] if non-combustible finishing material is used such as brick and stone.
Insulated sleeve
3"[76mm] to top
2"[51mm] to
sides / bottom
Non-combustible
Brick
Combustible1" [25mm] minimum all sides for vertical venting sections.When passing through a ceiling, use firestop W500-0028 (not supplied).
4"min.
12"[305mm]* 72"
(182.8cm)min.
10 1/4"
L’information du produit fourni n’est pas complet et est sujet de changer sans préavis. Consultez le manuel d’installation pour information d’installation actuel.
W415-2776 / A / 03.13.20
Pénétration du Mur
59” plus la pente
Sections d’ÉventsLors du passage à travers un mur, utilisez l’espaceur coupe-feu W010-1800 (fourni). Lors du passage à travers un plafond, utilisez l’espaceur coupe-feu W500-0028 (non fourni).
note:
Sections d’évents horizontale: Un dégagement minimum aux matériaux combustibles de 3” (76mm) au-dessus et 2” (51mm) sur les côtés et au-des-sous est requis. Sections d’évents verticale: Un dégagement minimum aux matériaux combustibles de 1” (25mm) est requis toute autour du conduit d’évacuation sur toutes les courses verticale.
Ossature Fini - Affl euré et Encastré
FOYER À GAZ VENTILÉ DIRECTE ÉLÉVATIONMD X 36
Ossature Fini - Affl euré Ossature Fini - Encastré
72”(183cm)
min.
39 3/4”
43 3/4”
72”(183cm)
min.Recessed
volume must be added to
the overall size of the
enclosure.
39 3/4”
Max. 5 1/2”
43 3/4”
* Le cadre encastré peut être « renforcé » avec une pièce contreplaqué d’un épaisseur de 3/4po pour supporter le matériel de montage du téléviseur.
* L’hauteur minimum de l’enceinte est déter-miné en fonction du volume d’air nécessaire dans l’enceinte.
22 1/4”22 1/4”
6” min.
6” min.6” min.
6” min.