Electronic code lock device
-
Upload
amitoj-kaur -
Category
Education
-
view
10.856 -
download
6
description
Transcript of Electronic code lock device
ELECTRONIC CODE LOCK DEVICE
CIRCUIT DESIGN OF ELECTRONIC CODE LOCK
INTRODUCTION
o Access control system that allows only authorized persons to access a
restricted area
o Allows the user to unlock the device with a password.
o The major components include a keypad, LCD and the controller P89V51
which belongs to the 8051 series of microcontrollers.
o User can also set his password to ensure better protection.
Can be adapted to any electronic gadget which needs to be protected
from unauthorised persons/access.
Responds only to the right sequence of four digits that are keyed in
remotely.
If a wrong key is touched, it resets the lock.
Block Diagram
COMPONENTS USED IN THE DEVICE
LCD 16*2
Resistors 10k*12, 1k*10, 1.5k
Crystal 11.0592Hz
Capacitors 33pF*2, 10µF, 0.1µF*3
IC7805
Battery power 9V
Switches
LED’s
Connecting wires
Microcontroller P89V51
MICROCONTROLLER P89V51
16/32/64 kB flash and 1024 B of data RAM
A key feature of the P89V51 is its X2 mode option.
The flash program memory supports both parallel programming and
in serial ISP
Supports 12-clock (default) or 6-clock mode selection via software
or ISP
Features
80C51 CPU
5 V operating voltage from 0 MHz to 40 MHz
16/32/64 kB of on-chip flash user code memory
PCA (programmable counter array) with capture/compare functions
Four 8-bit I/O ports with three high-current port 1 pins
Three 16-bit timers/counters
BLOCK DIAGRAM OF MICROCONTROLLER
PIN DIAGRAM
Vcc-Pin 40 provides supply voltage to the chip. The voltage source
is +5 V.
GND- Pin 20 is the ground.
RST-Pin 9 is the reset pin. It is an input and is active high (normally
low).
EA pin is connected to the Vcc and connected to pin no. 31.
PSEN is “program store enable.” It is the read strobe to external
program memory.
ALE is output pin and is active high. When connecting a
microcontroller to external memory, port 0 provides both address
and data.
I/O PORT PINS AND THEIR FUNCTIONS
PORT 0:an 8-bit open drain bidirectional I/O port. It is the
multiplexed low-order address and data bus
PORT 1:an 8-bit bidirectional I/O port. P1.5, P1.6, P1.7 have high
current drive of 16mA
PORT 2:8-bit bidirectional I/O port, it receives control signals and a
partial of high-order address bits during the programming
LIQUID CRYSTAL DISPLAY
o Flat panel display, electronic visual display, video display that uses the light modulating properties of liquid crystals .
APPLICATIONS
Used in computer monitors, television, instrument panels,
aircraft cockpit displays, signage, etc
an electronically modulated optical device made up of any number
of segments filled with liquid crystals and arrayed in front of a
light source or reflector to produce images in monochrome
Also used in video players, gaming devices, clocks, watches,
calculators, and telephones and have wide range of screen sizes
Vcc
1615141312111098
654321
7
1615141312111098
654321
7
D7
E
Vcc
D4
ContrastRS
Gnd
R/W
Gnd
D0
D3
D6D5
13
2
D2D1
LCD Pin Description
POWER SUPPLY
COMPONENTS USED
The transformer steps down the 220 V a/c. into 12 V a/c
A rectifier transforms ac into dc by limiting. The output resulting from a rectifier is a pulsating D.C. voltage
The ripple of the D.C. voltage is smoothened using a filter capacitor
The voltage regulator regulates the supply if the supply if the line voltage increases or decreases
WORKING OF PROJECT
As the program starts, string ‘Enter Password’ is displayed on LCD
After the four digits are entered, the user is prompted to ‘Confirm Password’
If the passwords do not match, a message is displayed to indicate ‘Wrong Password’
Again the keypad is scanned for pressed keys and corresponding digits are identified
If all the four digits match with set password, the lock output pin goes high
The system gets locked if more than three attempts are made with wrong password to open the electronic lock
The high output of the logic circuit enables the AND gate
APPLICATIONS:
used to automate the door locking process, so the user need not to carry the door lock keys
used in Mobile phones for security purposes
Used in Banks lockers
used in applications like Lift, Telephone Locking, Refrigerators etc
RESULT AND CONCLUSION
Result:-all electronics devices plays very important role in Programming and in Electronics Department
Conclusion:-All electronics devices can perform many functions using interfacing and programming with Embedded C language
Future scope:-In future, the improved version of Microcontrollers will be more useful.In serial communication and Robotics, everywhere we need Microcontrollers to store program in it
REFERENCES
www.electronicsforyou.com
www.encyclopedia.com
www.wikipedia.com
Thank you