Electrical cabinet products - Catalogue I. Screwdrivers 2004_2005.pdf · Tools Screwdrivers N.44 N...

Too

ls

Screwdrivers

N.44

N

Crimped conductors can be fastened in the corresponding con-nection chamber either by the direct plug-in technique or bymeans of screws.

Electric screwdrivers

Weidmüller screwdrivers are ideal one-hand tools due to theirergonomic design. They guarantee fatigue-free working in anyinstallation direction. They also have an automatic torque limitand high repetition accuracy.

Weidmüller bits

The Weidmüller bits are standard bits with high quality, widerange and top-rate performance. Weidmüller uses processor-controlled hardening processes to guarantee consistently highproduct quality.

The high-grade material enables torques far above those stipu-lated in the relevant DIN standards:

• DIN 5261 for PH/PZ bits

• DIN 5263 for slot bits

• Camcar standard for TORX bits

This means long service life at high torques, producing idealconditions for standard work.

Product benefits:

• Suitable for all screw driving tasksIdeal for both manual and machine screw driving tasks dueto the high hardness values of 59 – 61 HRC

• Good wear-resistance and therefore long service life

• Optimum fit in DIN screws for low wear and optimum torquetransmission

• Manufactured with consistently high product quality drivenby the relevant ISO standards.

N044_GB.qxd 23.10.2003 15:24 Uhr Seite 44

N.45

N

Screwdrivers

Rechargeable torque screwdriver

Screwdriver

Motor

Idling speed

Max. torque

Chuck

Length

Weight

Battery

Type

Weight

Charger

Input

Output

Charging time

Weight

Technical data

2.4 V DC

200/400 rpm

3.0 Nm

1/4" C6.3 DIN 3126

239 mm

400 g

2 Ni-Cd batteries each 1.2 V

122 g

230 V AC, 50 Hz, 50 mA

2.9 V AC, 1.4 A, 4.1 VA

1 hour

700 g

DMS 3 DMS 3 Set

Type Qty Order no.

DMS 3 1 9007440000

Screwdriver incl. battery

Ordering dataType Qty Order no.

DMS 3 set 1 (screwdriver incl. battery, 1 9007470000

charger, bits, plastic carrying case)

DMS 3 set 2 (as set1 1 9007470000

with 1 additional battery)

Type Qty Order no.

Spare battery 1 9007450000

Charger 1 9007460000

Accessories

DMS 3 rechargeable torque screwdriver

• One-hand operation under all working conditions

• Switchable forward and reverse

• Two speeds: 200 and 400 rpm

• Precise torque settings fromapprox. 0.2 ... 3 Nm in 6 steps

• Consistent performance during battery dis-charge

• Grip swings easily from rod to pistol form

• Takes 1/4" bits held by ball-bearing clampingmechanism (form E6.3)

• Safety lock prevents inadvertent switch-on

• Easy changeover from battery drive to manualoperation up to 15 Nm

Too

ls

Articles with coloured order number are kept permanently in stock at the central warehouse in Germany.Delivery times see page X.2

N045_GB.qxd 11.10.2003 10:08 Uhr Seite 45

N.46

N

Screwdrivers

Electric torque screwdriver

Rated voltage

Frequency

Rated power

Current consumption

Rpm of spindle in searching mode

in working mode

Torques

Level 1 (M 2.5)

Level 2 (M 3)

Level 3 (M 3.5)

Level 4 (M4)

Weight incl. supply cable

Weight

Noise level acc. to DIN 45 634

Protection class II acc. to DIN 57 740

DIN/VDE 0740 T.1 and T.2

EMC acc. to EC directive 89/336/EEC

CE mark

Technical data

230 V

50 Hz

45 W

0.2 A

350 min-1

700 min-1

0.5 ± 0.1 Nm

0.7 ± 0.15 Nm

1.2 ± 0.2 Nm

1.7 ± 0.25 Nm

0,990 kg

0,820 kg

58 db (A)

DMS 2

Type Qty Order no.

DMS 2 with 1/4" drive 1 0664600000

Form C 6.3 DIN 3126 with hang-up clamp and 4 bits for slotted screws (50 mm)

Dimensions of the blade 0.5 x 3 / 0.6 x 3.5 / 0.8 x 4 / 1.0 x 5.5

Standard equipment

Ordering data

Type Qty Order no.

BAL 2 (balancer for hanging up the DMS 2) 1 018180000Balancer for hanging up the DMS 2

Accessories

• Torque adjustable in four steps for standardscrews M2.5 to 4

• Selectable electric power-off when reaching apredefined torque

• High repetition accuracy• Start in search-gear and switching to working

rotation speed is controlled via the pressingpower onto the screw head

• Switchable forward and reverse• Fatigue-free working due to ergonomic design

and low weight• Ideal design for one-hand operation under all

working conditions and at different working loca-tions

• Low noise• Low energy consumption

Too

ls


N046_GB.qxd 11.10.2003 10:10 Uhr Seite 46

N

Articles with coloured order number are kept permanently in stock at the central warehouse in Germany.Delivery times see page X.2 N.47

Screwdrivers

Too

ls

Bits - drive A5.5

5.5 mm hexagon insert bit drive acc. to DIN 3126, form A 5.5for direct connection (for electric screwdriver Type DMS2 A 5.5)

Type Size A B C Order no.

Bit A5.5 S

Slot-head bits DIN 5264, drive A5.5 DIN 3126 BIT A5.5 0.5X3,0X50 0.5 3 50 0498500000BIT A5.5 0.5X3,0X75 0.5 3 75 9024730000BIT A5.5 0.6X3,5X50 0.6 4 50 0498600000BIT A5.5 0.6X3,5X75 0.6 4 75 0535100000BIT A5.5 0.8X4,0X50 0.8 4 50 0498700000BIT A5.5 0.8X4,0X75 0.8 4 75 9024740000BIT A5.5 0.6X4,5X50 0.6 5 50 9009220000BIT A5.5 1.0X5,5X50 1.0 6 50 0498800000BIT A5.5 1.0X5,5X125 1.0 6 125 0499100000

C

A

B

Bit A5.5 PH

Cross-head bits Type Phillips-Recess PH/DIN 5260, drive A5.5 DIN 3126 BIT A5.5 PH 1X50 1 50 0384800000BIT A5.5 PH 1X75 1 75 0529900000BIT A5.5 PH 2X50 2 50 0384900000BIT A5.5 PH 2X125 2 125 0533600000BIT A5.5 PH3x50 3 50 9009260000

C

Bit A5.5 PZ

Cross-head bits Type Pozidriv PZ/DIN 5262, drive A5.5 DIN 3126 BIT A5.5 PZ 1X50 1 50 9024850000BIT A5.5 PZ 2X50 2 50 9024860000BIT A 5.5 PZ3x50 3 50 9009300000

C

UBH 5.5

Universal bit holder, magnetic, drive: A5.5 DIN 3126 output: 1/4’’ D6.3 UBH 5.5 9024890000

Bit-Box

Weidmüller Bit-Box, 9-part with universal-holder drive: A5.5 DIN 3126output: 1/4’’ D6.3 bits 1/4’’ C6.3

Bit-Box WI 9024900000

N047-N051_GB 23.10.2003 15:56 Uhr Seite N.47

N

N.48Articles with coloured order number are kept permanently in stock at the central warehouse in Germany.

Delivery times see page X.2

Screwdrivers

Too

ls

Bits - drive 1/4 C6.3

1/4’’-hexagon insert bit drive acc. to DIN 3126,form C 6.3 for direct connection (DMS2 1/4’’ C6.3)


Bit C6.3 S

Slot-head bits DIN 5264, drive 1/4’’ C6.3 DIN 3126

C

A

B

Bit C6.3 PH

Cross-head bits type Phillips-Recess PH/DIN 5260, drive 1/4’’ C6.3 DIN 3126

C

Bit C6.3 PZ

Cross-head bits Type Pozidriv PZ/DIN 5262, drive 1/4’’ C6.3 DIN 3126

C

UBH 1/4 C6.3

Universal bit holder, magnetic, drive: 1/4’’ C6.3 DIN 3126 output: 1/4’’D6.3

BHS 1/4

Bit holder with flexible shank for angled screwing, for all bits 1/4’’ driveC6.3 DIN 3126 with SoftFinish-grip

BIT C6.3 0.5X3.0X39 0.5 3 39 9025500000BIT C6.3 0.5X3.0X75 0.5 3 75 9024750000BIT C6.3 0.6X3.5X39 0.6 4 39 9025510000BIT C6.3 0.6X3.5X75 0.6 4 75 9024760000BIT C6.3 0.5x4.0x25 0.5 4 25 9009310000BIT C6.3 0.8X4.0X39 0.8 4 39 9025520000BIT C6.3 0.8X4.0X75 0.8 4 75 9024770000BIT C6.3 0,6x4,5x25 0.5 5 25 9009320000BIT C6.3 1.0x5.5X39 1.0 6 39 9025530000BIT C6.3 1.0X5.5X125 1.0 6 125 9024780000

BIT C6.3 PH0x25 0 25 9009330000BIT C6.3 PH1x25 1 25 9009340000BIT C6.3 PH 1X50 1 50 9025540000BIT C6.3 PH 1X75 1 75 9024830000BIT C6.3 PH2x25 2 25 9009350000BIT C6.3 PH 2X50 2 50 9025550000BIT C6.3 PH 2X125 2 125 9024840000

BIT C6.3 PZ0x25 0 25 9009360000BIT C6.3 PZ1x25 1 25 9009370000BIT C6.3 PZ1X50 1 50 9024870000BIT C6.3 PZ2x25 2 25 9009380000BIT C6.3 PZ 2X50 2 50 9024880000

UBH 1/4 C6.3 9009620000

BHS 1/4 9009630000

N047-N051_GB 23.10.2003 15:56 Uhr Seite N.48

N


Screwdrivers

Too

ls

Bits-drive 1/4 C6.3

1/4-male hexagon drive according to DIN 3126,form C06.3 for direct connection (DMS3)


Bit-Box DMS2

Weidmüller Bit-Box, 9-part with universal-holder drive: 1/4’’ C6.3 DIN3126 output: 1/4’’ D6.3 bits 1/4’’ C6.3

Bit-Box WI DMS 2 9024910000

N047-N051_GB 23.10.2003 15:56 Uhr Seite N.49

N



Screwdrivers

Too

ls

Bits - drive 1/4 E6.3

1/4’’-hexagon insert bit drive acc. to DIN 3126,form E6.3 for direct connection (DMS3)


Bit E6.3 S

Slot-head bits DIN 5264, drive 1/4’’ E6.3 DIN 3126

C

B

Bit E6.3 PH

Cross-head bits Type Phillips-Recess PH/DIN 5260, drive 1/4’’ E6.3 DIN 3126

C

Bit E6.3 PZ

Cross-head bits Type Pozidriv PZ/DIN 5262, drive 1/4’’ E6.3 DIN 3126

C

UBH 1/4 E6.3

Universal bit holder, short, magnetic, drive: 1/4’’ E6.3 DIN 3126, output:1/4’’ D6.3

UBH SWH 1/4

ClicFix Universal quick-change holder with locking function and magnet.Real one-hand operation for quick bit changing 1/4’’ drive E6.3 DIN 3126,output 1/4’’ D6.3

BIT E6.3 0.5x3x50 0.5 3 50 9009410000BIT E6.3 0.5X3.0X70 0.5 3 70 9024000000BIT E6.3 0.6x3.5x50 0.6 4 50 9009420000BIT E6.3 0.6X3.5X70 0.6 4 70 9024020000BIT E6.3 0.8x4.0x50 0.8 4 50 9009430000BIT E6.3 0.8X4.0X70 0.8 4 70 9024030000BIT E6.3 1.0x5.5x50 1.0 6 50 9009440000BIT E6.3 1.0X5.5X70 1.0 6 70 9024040000

BIT E6.3 PH 1X70 1 70 9024080000BIT E6.3 PH 2X70 2 70 9024090000

BIT E6.3 PZ 1X70 1 70 9024100000BIT E6.3 PZ 2X70 2 70 9024110000

UBH 1/4 E6.3 9009520000

UBH SWH 1/4 9009510000

N047-N051_GB 23.10.2003 15:56 Uhr Seite N.50

N


Screwdrivers

Too

ls

Bits - drive 1/4 E6.3

1/4’’-male hexagon drive acc. to DIN 3126,Form E6.3 for direct connection (DMS3)


Bit-Box DMS3

Weidmüller Bit-Box, 9-part with universal-holder drive 1/4’’ E6.3 DIN3126, output 1/4’’ D6.3 bits 1/4’’ C6.3

Bit-Box WI DMS 3 9024970000

N047-N051_GB 23.10.2003 15:56 Uhr Seite N.51

N.52

N

Too

ls

Screwdrivers

Overview

Weidmüller screwdrivers come in four different grip sizes, andare the result of a consistent grip concept which takes intoaccount both the human hand and the different requirementswhen working

• Perfect handling with all grip sizes

• Maximum torques

• Optimum transmission of axial force

• Complete range including all commercial dimensions

SoftFinish-grip

With the SoftFinish zone for use in dry conditions and for gen-eral applications, Weidmüller offers a complete range of screw-drivers that enables far higher torques and at the same timesubstantially more comfort due to the soft material of the grip.

Product benefits:

• Made of special soft material which is kind to the skin, theSoftFinish zone enables maximum torques

• Perfect ergonomic grip design for comfortable screw drivingand optimum handling

• Version with solid steel tip can be used for chiselling

• You can choose from long-life extremely stressable blades in standard sizes

• ChromTop blade tip offers maximum corrosion protectionand greatest possible dimensional accuracy of the bladegeometry in the screw head over many years

SoftFinish electric

VDE-insulated screwdriver according to DIN EN 60900,IEC 900 for work on live equipment

Product benefits:

• The protective insulation directly injected onto the screwdriv-er blade ensures electrical safety, even in critical applications

• Safe for working at up to 1500 volts DC and 1000 volts AC

• Each screwdriver is individually tested in a water bath at10,000 volts according to DIN EN 60900

• Perfect ergonomic grip design for comfortable screw drivingand optimum handling

• Made of special soft material which is kind to the skin, theSoftFinish zone prevents slipping in critical situations and atthe same time enables maximum torques

N052_GB.qxd 23.10.2003 16:02 Uhr Seite 52

N.53

N

Screwdrivers

Combined cutting and screw drivingtool

Maximum cutting performance

Copper cable:

Solid cable (conductor cross-section) mm2

Flexible cable (conductor cross-section) mm2

Tool data

Length/width/height mm

Weight g

Technical data

1.5

2.5

35 / 18 / 40

20

swifty® swifty®set

Type Qty Order No.

swifty® (without screwdriver) 1 9006020000

Ordering dataType Qty Order No.

swifty®set (with screwdriver) 1 9006060000

Screwdriver 1 9008330000

(SD 0.6 3.5x100)

swifty®

• Cable cutting tool to mount on non-insulatedscrew drivers with a blade diameter of 3.5 mm

• Minimum manual force required

• Automatic opening of the cutter

• Ergonomically designed grip

swifty®set

• Efficient operation:

• Only one tool for cable-processingin IDC-technology

• Suitable for screw and tension clamps

• Readily available pocket sizefor right-handed and left-handed use

• One-hand operation

that does not damage the edge; for cutting ofcopper cables with a diameter of up to 1.5 mm2

solid and 2.5 mm2 flexible.

Too

ls


N053_GB.qxd 24.10.2003 8:10 Uhr Seite 53

ISK 5.0x129 5.0 125 9009000000ISK 5.5x128 5.5 125 9008990000ISK 6.0x128 6.0 125 9008980000ISK 7.0x127 7.0 125 9008970000ISK 8.0x127 8.0 125 9008960000ISK 9.0x126 9.0 125 9008950000ISK 10.0x126 10.0 125 9008940000ISK 11.0x125 11.0 125 9008930000ISK 13.0x125 13,0 125 9008920000

SDIK PZ1 1 80 9008900000SDIK PZ2 2 100 9008890000

SDIK PH0 0 60 9008560000SDIK PH1 1 80 9008570000SDIK PH2 2 100 9008580000SDIK PH3 3 150 9008590000

N



Screwdrivers

Too

ls

VDE insulated Screwdriver

VDE-insulated screwdriver sets, for working on live parts up to 1000 VAC and 1500 V DC. DIN EN 60900, IEC 900. safety tested GS, checkedindividually. Blade made from high-alloy chromium-vanadium-molybdenum steel, through-hardened, browned

Type Size / SW A B C Order No.

SDI S

VDE-insulated slot-head screwdriver, SDI DIN 7437, ISO 2380/2, outputacc. to DIN 5264, ISO 2380/1, SoftFinish-grip

SDIK PH

VDE-insulated crosshead screwdriver type Phillips, SDIK PH DIN 7438,ISO 8764/2-PH, output acc. to DIN 5260-PH, ISO 8764/1-PH, SoftFinish-grip

SDIK PZ

VDE-insulated crosshead screwdriver type Pozidriv SDIK PZ DIN 7438,ISO 8764/2-PZ, output acc. to DIN 5260-PZ, ISO 8764/1-PZ, SoftFinish-grip

SDIT

VDE-insulated Torx®-screwdriver, SDIT SoftFinish-grip

SKI

VDE-insulated hexagon socket wrench, ISK SoftFinishh-grip

SDI 0.4X2.5X75 0.4 2.5 80 9008370000SDI 0.5X3.0X100 0.5 3.0 100 9008380000SDI 0.6X3.5X100 0.6 3.5 100 9008390000SDI 0.8X4.0X100 0.8 4.0 100 9008400000SDI 1.0X4.5X125 1.0 4.5 125 9008910000SDI 1.0X5.5X125 1.0 5.5 125 9008410000SDI 1.2X6.5X150 1.2 6.5 150 9008420000SDI 1.6x8.0x175 1.6 8.0 200 9008430000

SDIT 10 10 80 9009640000SDIT 15 15 80 9009650000SDIT 20 20 80 9009660000SDIT 25 25 80 9009670000SDIT 30 30 100 9009680000SDIT 40 40 150 9009690000

SSB_N054_N054_GB 24.10.2003 8:22 Uhr Seite N.54

WK IK PZ 0 max. 0.9 Nm 175 9918490000WK IK PZ 1 max. 3.8 Nm 175 9918500000WK IK PZ 2 max. 5.5 Nm 175 9918510000

WK IK PH 0 max. 0.9 Nm 175 9918460000WK IK PH 1 max. 3.8 Nm 175 9918470000WK IK PH 2 max. 5.5 Nm 175 9918480000

WK SI 0.4 x 2.5 max. 0.6 Nm 0.4 2.5 175 9918410000WK SI 0.5 x 3.0 max. 0.6 Nm 0.5 3.0 175 9918420000WK SI 0.6 x 3.5 max. 1.1 Nm 0.6 3.5 175 9918430000WK SI 0.8 x 4.0 max. 2.5 Nm 0.8 4.0 175 9918440000WK SI 1.0 x 5.5 max. 3.8 Nm 1.0 5.5 175 9918450000

DMSI manual 0.5-1.7 0.5 - 1.7 Nm 9918390000DMSI manual 2.0-8.0 2.0 - 8.0 Nm 9918400000

N


Screwdrivers

Too

ls

VDE insulated Screwdriver

VDE-insulated screwdriver sets Weidmüller SoftFinish electric forworking on live parts up to 1000 V AC and 1500 V DC. DIN EN 60900,IEC 900. safety tested GS, individually Checked


SDIS 2.5-5.5/PH/1/2

6-part set: VDE-insulated slot-head and cross-head PH Screwdriver set

DMSI

VDE-insulated torque-screwdriverEN ISO 6789, BS EN 26789, ASME B107.14M

WK SI

VDE-insulated interchangeable blades for VDE-insulated torque-screwdriveroutput according to DIN 5264, ISO 2380/1

WK IK PH

VDE-insulated interchangeable blades for VDE-insulated torque-screwdriveroutput according to DIN 5260-PH, ISO 8764/1-PH

WK IK PZ

VDE-insulated interchangeable blades for VDE-insulated torque-screwdriveroutput according to DIN 5260-PZ, ISO 8764/1-PZ

SDI 0.4x2.5x75 0.4 2.5 80SDI 0.5x3.0x100 0.5 3.0 100SDI 0.8x4.0x100 0.8 4.0 100SDI 1.0x5.5x125 1.0 5.5 125SDI PH 1 80SDI PH 2 100SDIS 2.5-5.5/PH1/2 9009730000

SSB_N055-N055_GB 24.10.2003 8:30 Uhr Seite N.55

N



Screwdrivers

Too

ls

Uninsulated screwdriver

Weidmüller SoftFinish screwdriver for general uses, blade made fromhigh-alloy chromium-vanadium-molybdenum steel, through-hardened,matt chrome finish.


SD S

Slot-head screwdriver with circular blade SD DIN 5265, ISO 2380/2,ouput acc. to DIN 5264, ISO 2380/1, point chromium top, SoftFinish-grip

SDK PH

Crosshead screwdriver Type Phillips, SDK PH DIN 5262, ISO 8764/2-PH,ouput acc. to DIN 5260-PH, ISO 8764/1-PH, point chromium top,SoftFinish-grip

SDK PZ

Crosshead screwdriver Type Pozidriv, SDK PZ DIN 5262, ISO 8764/2-PZ, ouput acc. to DIN 5260-PZ, ISO 8764/1-PZ, point chromium top,SoftFinish-grip

SDTR

Torx® TR-screw driver with drill hole in the blade point (TamperResistant), SD TR for screwing of Torx® and Torx®-TR safety screws(centre pin in profile), point chromium top, SoftFinish-grip

SK

Hexagon socket wrench SK DIN 3125, ouput acc. to DIN 3125,SoftFinish-grip

SK 5.0x125 5.0 125 9009130000SK 5.5x125 5.5 125 9009120000SK 6.0x125 6.0 125 9009110000SK 7.0x125 7.0 125 9009100000SK 8.0x125 8.0 125 9009090000SK 9.0x125 9.0 125 9009080000SK 10.0x125 10.0 125 9009070000SK 11.0x125 11.0 125 9009060000SK 12.0x125 12.0 125 9009050000SK 13.0x125 13.0 125 9009040000

SDTR 8 8 60 9009190000SDTR 10 10 80 9009180000SDTR 15 15 80 9009170000SDTR 20 20 100 9009160000SDTR 25 25 100 9009150000SDTR 30 30 115 9009140000

SDK PZ0 0 60 9008520000SDK PZ1 1 80 9008530000SDK PZ2 2 100 9008540000SDK PZ3 3 150 9008550000

SDK PH0 0 60 9008470000SDK PH1 1 80 9008480000SDK PH2 2 100 9008490000SDK PH3 3 150 9008500000

SD 0.4x2.0x60 0.4 2.0 60 9037160000SD 0.4x2.5x75 0.4 2.5 75 9009030000SD 0.5X3.0X80 0.5 3.0 80 9008320000SD 0.6X3.5X100 0.6 3.5 100 9008330000SD 0.6X3.5X200 0.6 3.5 200 9010110000SD 0.8X4.0X100 0.8 4.0 100 9008340000SD 1.2x6.5x150 1.2 6.5 150 9009010000SD 0.8x4.5x125 0.8 4.5 125 9009020000SD 1.0X5.5X150 1.0 5.5 125 9008350000


N


Screwdrivers

Too

ls

Uninsulated screwdriver

Set of interchangeable blades made from high-alloy chromium-vanadium-molybdenum steel, through-hardened, high-qualitygalvanised finish.


System 11+1 S-PH-PZ-SK

12-part set of interchangeable bladesfor slot-head, cross-head PH/PZ and hexagon screws, SoftFinish-grip

System 11+1 TW-TS-TR

12-part set of interchangable blades for screwing of Torx®, Torq® andTri-Wing®safety screws.

Set S 2.5/3.0/4.0/5.5/PH 1/2

12-part set of interchangeable bladesfor slot-head, cross-head PH screwdriver set with circular blades

Set TR 10/15/20/25/30/40

6-part set: Torx® screw driver with drill hole in the blade point

SD STK

Flat blade screwdriver with solid steel cap SD STK DIN 5265, ISO2380/2, ouput acc. to DIN 5264, ISO 2380/1, can also be used as achisel due to steel cap SoftFinish-grip

SD 0.5 3 140SD 0.8 4 140SD 1.0 5 140SD 1.2 6 140PH 1 1 140PH 2 2 140PZ 1 1 140PZ 2 2 140SK 3.0 3 140SK 4.0 4 140SK 5.0 5 140System 11+1 9009750000

TW 1.0 140TW 2.0 140TW 3.0 140TW 4.0 140TS 6.0 140TS 8.0 140TR 10.0 140TR 15.0 140TR 20.0 140TR 25.0 140TR 30.0 140System 11+1 Secur. 9009760000

SD 0.4x2.5x75 0.4 2.5 75SD 0.5x3.0x80 0.5 3.0 80SD 0.8x4.0x100 0.8 4.0 100SD 1.5x5.5x125 1.0 5.5 125SD PH 1 1 80SD PH 2 2 100SDS 2.5-5.5/PH1/2 9009740000

SD TR 8 8 60SD TR 10 10 80SD TR 15 15 80SD TR 20 20 100SD TR 25 25 100SD TR 30 30 150SDS TR8-30 9009720000

SD STK 8x150 1.2 8 150 9009700000SD STK 10x175 1.6 10 175 9009710000


WK K PZ 0 max. 0.9 Nm 175 9918600000WK K PZ 1 max. 3.8 Nm 175 9918610000WK K PZ 2 max. 5.5 Nm 175 9918620000

DMS manual 0.5-1.7 0.5 - 1.7 Nm 9918370000DMS manuell 2.0-8.0 2.0 - 8.0 Nm 9918380000

N



Screwdrivers

Too

ls

Screwdriver

Torque-screwdriver Weidmüller SoftFinish


DMS

Torque-screwdriverEN ISO 6789, BS EN 26789, ASME B107.14M

WK K PZ

Interchangeable blades for torque-screwdriveroutput according to DIN 5260-PZ, ISO 8764/1-PZ

WK K PH

Interchangeable blades for torque-screwdriveroutput according to DIN 5260-PH, ISO 8764/1-PH

WK K S

Interchangeable blades for torque-screwdriveroutput according to DIN 5264, ISO 2380/1

WK K PH 0 max. 0.9 Nm 175 9918570000WK K PH 1 max. 3.8 Nm 175 9918580000WK K PH 2 max. 5.5 Nm 175 9918590000

WK S 0.4 x 2.5 max. 0.6 Nm 0.4 2.5 175 9918520000WK S 0.5 x 3.0 max. 0.6 Nm 0.5 3.0 175 9918530000WK S 0.6 x 3.5 max. 1.1 Nm 0.6 3.5 175 9918540000WK S 0.8 x 4.0 max. 2.5 Nm 0.8 4.0 175 9918550000WK S 1.0 x 5.5 max. 3.8 Nm 1.0 5.5 175 9918560000


N


Screwdrivers

Too

ls

Wrench set Weidmüller

Allen key in PocketStarAllen key made from high-alloy chromium-vanadium- steel, acc. toDIN ISO 2936 L (DIN 911), surface high-quality refined.


SK WSD S

9-part offset screwdriver set in Prostar, with MagicRing: holds standardscrews in any position thanks to spring steel ring (beginning with size3), with spherical head: for angled screwing up to 25°.

SK S

7-part allen key set

SK S

7-part allen key set with MagicRing and spherical head: holds standardscrews in any position thanks to spring steel ring (beginning with size 3), withspherical head: for angeled screwing up to 25°.

TR S

8-part Torx® TR-screw driver setwith drill hole in the blade point (Tamper Resistant), for screwing of Torx® andTorx®-TR safety screws (centre pin in profile)

1.52.02.53.04.05.06.08.010.0

SK WSD-S 1.5-10.0 9008850000

2,02,53,04,05,06,08,0

SK-S 2.0-8.0 MR 9008870000

2.02.53.04.05.08.06.0

SK-S 2.0-8.0 9008860000

910152025273040

TR-S 9-40 9008880000


Electrical cabinet products - Catalogue I. Screwdrivers 2004_2005.pdf · Tools Screwdrivers N.44 N...

Documents

Transcript of Electrical cabinet products - Catalogue I. Screwdrivers 2004_2005.pdf · Tools Screwdrivers N.44 N...