Electric FanFS40-16CR

READ AND SAVE THESE INSTRUCTIONS

Version 1.0 2017 Attention: Pictures in the IM are for reference only.

OWNER’S MANUAL

Read Rules for Safe Operation and Instructions Carefully.

CAUTION

IMPORTANT SATETY INSTRUCTIONS

WARNING

1.Do not leave the fan running unattended.

2.Keep electrical appliances out of reach from Children or infirm persons. Do not let them use the appliances without supervision.

3.This appliance has a polarized plug (one blade is wider than the other). To reducethe risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.

4.If the supply cord is damaged, it must be replaced by manufacturer or itsservice agent or a similarly qualified person to avoid a hazard.

5.This appliance is not intended for use by persons (including children) with reducedphysical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by aperson responsible for their safety. Young children should be supervised to ensure thatthey do not play with the appliance.

6.When the fan was assembled, the rotor blade guard shall not be taken off anymore• Prior cleaning unplug the fan.• The rotor guard shall not be dissembled/opened to clean the rotor blades.• Wipe the fan enclosure and rotor blade guard with a slightly damp cloth.

7.WARNING—To reduce the risk of fire or electric shock, Do not use this fan with anysolid-state speed control device.

8.This product employs overload protection (fuse). A blown fuse indicates an overloador short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded or returned to an authorized service facility for examination and/or repair.

a) “Do not operate any fan with a damaged cord or plug. Discard the fan or return it to an authorized service facility for examination and/or repair.”

b) “Do not run the cord under carpeting. Do not cover it with throw rugs, runners, or similar coverings. Do not route the cord under furniture or appliances. Arrange the cord away from traffic area and where it will not be tripped over.”

INSTALLATION INSTRUCTIONS

Name of components

1.Base Installation：Align the tube with the groove on the base. Fix them together by screwing the nut at bottom..

Position the rear grill against the motor so that the pins on the motor fit through the matching holes of the rear grill.

Tube

Motor

Motor shaft

Rear grillTightenknob

3.Install byaligning

Base

Nut

Considerate Hint:Remove parts from the component before performing installation.

RULES FOR SAFE OPERATION

1. Never insert fingers, pencils, or any other object through the grill when fan is running.2. Disconnect the fan when moving from one location to another.3. Be sure the fan is on a stable surface when operating to avoid overturning.4. DO NOT use it by window, rain may create electrical hazard.5. Household use only.

3.Install the Rear grill:

2.Connect the Tube to Motor:Adjusting the tighten knob and insert the motor part.

Lock nut of grill

Lock nut of blade

Blade

4. Tighten the Rear grill by screwing the lock nut of grill clockwise.

6. Tighten the Blade: Screw the lock nut of blade anticlockwise

5. Install the Blade: Put the fan blade through the motor shaft. After installment, gently rotate the blade to check whether it works normally.

Front grill

Grill Lock

1

2

3

1

2

3

Align the Front Grill with the Rear Grill at the illustrated position.

Press them gently as the figure to check if the two grills are well connected.

Fix the Grill Lock with a screw.

7. Front and Rear Grills Installation

3. Be sure the fan is on a stable surface when operating to avoid

Instructions for display of body

Instructions for key of remote controller

INSTRUCTIONS FOR USE

MODE

DRIVE PLATE ON/OFF

PRO/Timer

OSC

Considerate Hint:1. Install the battery with the positive side facing up.2. Effective Range of Remote Control: within 5 meters distance and 30-degree deflection in front of Product.

Battery installation

Rearcover

PUSHOPEN

Speed / Timer display

TimerSleep

Natural Silent

Remote Control:

Drive PlateRotate it to adjust the speed/time setting (Clockwise for increase, Anticlockwise for decrease)

ON/OFF KeyPress it once, the fan will turn on at normal mode. Press it again to shut off. (The fan starts at speed 01. Rotate the Drive Plate clockwise for higher speed. The wind speed ranges from 01 to 12 with an increment of 1)

OSC KeyAfter the fan starts, press this key once to start oscillation. Press the key again to stop it at the desired direction.

Mode KeyAfter turning on the fan, press it repeatedly to choose the mode in order of “Sleep-Natural-Silent”. Press it the fourth time and exit to the normal mode.

PRO/Timer Keya. Setting a Starting Time:Plug in the unit. Press this key once without turning on the fan. Rotate the Drive Plate to select time from “0.5 to 12 hours”with an increment of 0.5. (The increment increases to 1 after the number reaches 10 hours) The starting time was set up when the number on screen flashes once. Then a clock signal will be on display. And the fan will automatically turn on at your setting time.

b. Setting a Stopping Time: After turning on the fan, press this key into time setting. Rotate the Drive Plate as above to select time. The stopping time was set up after the number flashes once. And the clock signal will be on screen. Then the fan will automatically turn off at the appointed time.

(PS: To exit time setting, press the PRO/Time Key again. To cancel the time setting, press the time key once, rotate the hour to 00. Wait for 5-10 seconds, the former time setting was canceled when the clock signal disappears on screen.)

The fan will auto shut off after 12 hours without operation.

Instructions for operation of body

INSTRUCTIONS FOR USE

Body keyHeightAdjustmentKnot

Height AdjustmentScrew the knot clockwise and loosen it for adjusting the height

Drive Plate: Rotate it to adjust the speed/time setting

Mode Button: Repeatedly press the mode button in the middle, and select modes in the cycle of “Normal-Sleep-Natural-Silent-Normal”.

OSC Button: Press it once to start oscillation. Press the button again to stop it at the desired direction.

On/OFF Button: Press it once to turn on the fan at Normal mode. Press it again to turn off.

CLEANING1. Be sure to unplug the fan from the electrical supply source before cleaning.2. Plastic parts should be cleaned with mild soap and a damp cloth or sponge. Thoroughly to remove soap film with clean water.3. Be sure not to make water or other liquid enter inside of motor.

Notice: 1. When you replace the fuse, please don’t operate suddenly or overexert, or else the product will be damaged or cause accident.2. When you feel it hard to operate, please make sure you have got the right way.

a) Grasp the plug and remove it from the receptacle or other outlet device. Do not unplug it by pulling on cord.b) Open the fuse cover. Slide to open the fuse access cover on top of the attachment plug towards blades.c) Remove the fuse carefully. Insert the tip of your tool into fuse slot (close with the terminal).Then pry the fuse gradually and slowly,but not overexert. If it’s tight, you can try it at several times and pry the fuse little by little. When one side of the fuse has been pried, then you can get the fuse out entirely.d) Risk of fire. Replace the fuse only with 2.5 Amp, 125 Volt fuse.e) Close the fuse cover. Slide to close the fuse access cover on top of the attachment plug.f) Risk of fire. Do not replace the attachment plug, which contains a safety device (fuse) that should not be removed. Discard the product if the attachment plug is damaged.

USER SERVICING INSTRUCTIONS