Elect Consumption
-
Upload
supriya-nanda -
Category
Documents
-
view
229 -
download
0
Transcript of Elect Consumption
-
8/12/2019 Elect Consumption
1/20
Page | 1
Annexure A
List of Machineries with Specification for DFT & TD Department.(Amount in Rs. )
S.
No.Item Name Specifications Qty
EMDAmount
1 Straight Knife cutting machine
Application Cutting Fabric
1 2970
Electricity Single Phase
Motor Dual Speed - 2 HP
RPM Around 4000
Cutting Capacity 3.5 inch
Belt Fine 120 Medium
Blade Size Max. 5 inch - HSS
Blade Material High Speed Steel
Stroke Size Max. 1 &1/8 inch
Warranty 3 years AMC Components to be specified
2 Round Cutter
Application Cutting Straight lines
1 870
Electricity Single Phase
Blade Size Maximum 5 inch
Cutting Capacity 3 inch
Blade Material High Speed Steel
Power 0.34 HP
Sharpner Stone 150 Medium
Speed Single Speed
Warranty 3 years AMC Components to be specified
-
8/12/2019 Elect Consumption
2/20
-
8/12/2019 Elect Consumption
3/20
Page | 3
7
Direct Drive S.N.L.S. machine with
Under Bed Trimmer - with Panel,
Motor, Table & Stand - Complete Set
with Control Panel with following
minimum requirement
1. Programme for 4 steps
2. Auto back tack at start & end3. Speed Control
4. Slow Start Option
Application Medium Weight Materials
40 71640
Electricity Single Phase
Sewing Speed Approx. Min. 4000 to 5000 RPM
Stitch Type 301
Needle Bar Stroke Max. 29 to 32 mm
Stitch Length Max. 5 mm
Motor Servo Type Direct Drive
UBT Yes
Lubrication Semi Dry
Warranty 3 years AMC Components to be specified
8
Single Needle Lock Stitch machine -
with Motor, Table & Stand -
Complete Set With Control Panel
with following minimum requirement
1. Programme for 4 steps
2. Auto back tack at start & end
3. Speed Control
4. Slow Start Option
Application Heavy Weight Materials (Leather)
1 747
Sewing Speed Min. 3000 RPM
Feed Type Variable Top & Bottom Feed
Stitch Type 301
Needle Bar Stroke Max. 37 mm
Stitch Length Max. 8 mm
Electricity Single PhaseUBT Yes
Pressure Foot Lift 13-17mm Knee lifter
Pressure Foot Lift 6 mm for Handlifter
Motor Direct Drive
Lubrication Semi Dry
Warranty 3 years AMC Components to be specified
9
Single Needle Lock Stitch machine
with Needle Feed & Edge Cutter with
Motor, Table & Stand - Complete Set
with Control Panel with following
minimum requirement
1. Programme for 4 steps
2. Auto back tack at start & end
3. Speed Control
4. Slow Start Option
Application Heavy Weight Materials
1 2583
Sewing Speed Min. 3000 RPM+
Feed Type Needle Feed
Side Cutter Required (1/2" distance from Needle)
Stitch Type 301
Stitch Length 4 - 8 mm
UBT Yes
Lubrication Semi Dry
Clutch Motor Direct Drive
Warranty 3 years AMC Components to be specified
-
8/12/2019 Elect Consumption
4/20
Page | 4
10
Single Needle Lock Stitch machine
with Unison Feed with Motor, Table
& Stand - Complete Set with Control
Panel with following minimum
requirement
1. Programme for 4 steps
2. Auto back tack at start & end3. Speed Control
4. Slow Start Option
Application Heavy Weight Materials (Leather)
1 3723
Sewing Speed Min. 3000 RPM
Feed Type Unison Feed
Side Cutter Required
Stitch Type 301
UBT Yes
Lubrication Semi Dry
Stitch Length Max. 9 mm
Motor Direct Drive
Warranty 3 years AMC Components to be specified
11
S.N.L.S. Zig Zag (Fully Programmable)
machine with Motor, Table & Stand -
Complete with Control Panel with
following minimum requirement
1. Programme for 4 steps
2. Auto back tack at start & end
3. Speed Control
4. Slow Start Option
Application Light to Medium Weight Materials
1 10500
Sewing Speed Min. 4000 RPM
Stitch System Standard Zig Zag, 3 Step/Changeable
Input Function Panel Board
Bobbin thread winder Built in machine head
Custom Pattern Internal Min 20 pattern
Custom Pattern card Min 999 Pattern
Max. No. of Stitch 500 stitches/pattern
UBT Yes
Contnu. Stitch pattern Max. 10pattern, 20step, 500 stitches/step
Needle throw m/m Computer controlled
Max. Feeding Amount 2.5 mm
Zig Zag Width Max. 10 mm
Feature Required Should be able to make design also
Motor Direct Drive
Warranty 3 years AMC Components to be specified
-
8/12/2019 Elect Consumption
5/20
Page | 5
12
Double Needle Chain Stitch Machine -
with Motor, Table & Stand -
Complete Set with Control Panel with
following minimum requirement
1. Programme for 4 steps
2. Auto back tack at start & end
3. Speed Control
4. Slow Start Option
Application Plain Seaming
1 6591
Maximum Stitch Length 4 mm
Bed Type Flat
Stitch Type 401
Sewing Speed Minimum 5500 RPM
Lift of the Pressure Foot 5 mm to 8 mm
Stitch Condensation Required
Needle Gauge 6.4 mm
Attachments Lap Seam Folder
Motor AC Servo Motor / Direct Drive
UBT Yes
Warranty 3 years AMC Components to be specified
13
Double Needle Lock Stitch Machine
with Split Bar - Motor, Table & Stand
- Complete Set with Control Panel
with following minimum requirement
1. Programme for 4 steps
2. Auto back tack at start & end
3. Speed Control
4. Slow Start Option
Application Medium Weight Materials
1 4542
Feed Type Needle Feed cum Drop Feed
Stitch Type 301
Sewing Speed Minimum 3000 RPMUBT Yes
Lift of the Pressure Foot 5 mm to 8 mm
Stitch Length 5 mm
Needle Gauge 6.4 mm
Attachments Lap Seam Folder
Hook Vertical Axix Regular Hook (Cap Type)
Lubrication Semi Dry
Split Needle Bar Standard
Machine Bed Size 550 X 178 mm
Bed Size 1040 x 540 mm
Electricity Single Phase
Motor Direct Drive / Servo
Warranty 3 years AMC Components to be specified
-
8/12/2019 Elect Consumption
6/20
-
8/12/2019 Elect Consumption
7/20
Page | 7
15
Electronic Key Button Holer - Motor,
Table & Stand - Complete Set with
Control Panel with following
minimum requirement
1. Programme for 4 steps
2. Auto back tack at start & end
3. Speed Control
4. Slow Start Option
Application To make Key Button Holer
1 26148
Type of Cloth Clamp Flat Type
Sewing Speed 400 ~ 2200 RPM
Button Hole Length 40 mm Minimum
Stitch Length 1.5 mm Minimum
Stitch Width 3.2 mm Minimum
Stitch Type Single Needle Double Chainstitch (gimp)
UBT Yes
Hole Cutting MethodCut After or Cut Before-Option availability
is desired
Feed System Intermittent Feed by Stepping motor
Cloth cutting knife Drive Vertically Driven Stepping motor
Lubrication Automatic (Looper & Spreader by an Oiler)
Power Requirement Single Phase 550 VA
Motor Servo Type
Warranty 3 years AMC Components to be specified
16
Electronic Lock Stitch Bar Tacker -
Motor, Table & Stand - Complete Set
with Control Panel with following
minimum requirement
1. Programme for 4 steps
2. Auto back tack at start & end
3. Speed Control
4. Slow Start Option
Application Bar Tacking on Ordinary Materials
1 8877
Sewing Speed Min 2500 RPM
Stitch Length 0.1 - 10.00 mm
Stitch Width 30 x 10 mm
UBT Yes
Input Function Required
Sewing Area 30 x 40 mm
Stitch Length 0.1 ~10 mm
Lclamp Lift 14 mm
Needle Thread Tension Active Tension Device - Recommanded
Hook Standard Shuttle Hook
No. of Stitches memory 20,000 Stitches
No. of Standard Pattern 50 Pattern
Motor Direct Drive
Power Consumption 320 Watt
Lubrication Only minute quantity lubrication for hook
Enlarge &reduce facility 20 ~200% of the program
Warranty 3 years AMC Components to be specified
-
8/12/2019 Elect Consumption
8/20
Page | 8
17Blind Stitch Machine - Motor, Table &
Stand - Complete Set
Application Blind Stitch on Light to Medium Fabric
1 4290
Stitch Type Single Chain Stitch
Stitch Type 103
Bed Type Cylinder
Stitch Length 3.2 to 8.5 mm
UBT Yes
Speed Minimum 2000 RPM
No. of Needles 1
No. of Threads 1
Stith Skip Ratio 1:1 or 2:1
Motor Standard / Clutch Servo
Penetration Depth Max. 0.8 mm
Warranty 3 years AMC Components to be specified
18
Lock Stitch Button Sewing Machine -
Motor, Table & Stand - Complete Set
with Control Panel with following
minimum requirement
1. Programme for 4 steps
2. Auto back tack at start & end
3. Speed Control4. Slow Start Option
Application Button Sewing
1 11298
Sewing Speed Min 2000 RPM
Height Of Button Clamp Minimum 12 mm
Sewing Area Minimum 6mm x 6 mm
UBT Yes
Input Function Required
Stitch Length 0.1 ~10 mm
Lclamp Lift 14 mm
Needle Thread Tension Active Tension Device
Hook Standard Shuttle Hook
No. of Stitches memory 20,000 Stitches
No. of Standard Pattern 50 Pattern
Motor Direct Drive
Lubrication Only minute quantity lubrication for hook
Enlarge &reduce facility 20 ~200% of the program
Warranty 3 years AMC Components to be specified
-
8/12/2019 Elect Consumption
9/20
-
8/12/2019 Elect Consumption
10/20
Page | 10
22
Single Threads Saddle Stitch Machine
- Motor, Table & Stand - Complete
Set
Application Ornamental Stitch
1 6969
Stitch 101
Sewing Speed Min 1500 RPM
Motor Standard clutch / AC Servo
Warranty 3 years AMC Components to be specified
23
Computeized Single Head Embroidery
Designing machine including
software & all attachments for
sequins, etc - Motor, Table & Stand -
Complete Set
Application Embroidery
1 29400
No. of Heads 1
UBT Yes
No. of Needles Minimum 12
Embroidery Area Min. 400 mm x 800 mm
246 Threads Safety Stitch machine -
Motor, Table & Stand - Complete Set
Application Safety Stitch Machine
1 1779
Sewing Speed Min. 1200-2000 RPM
Feed Type Differential
Differential Ratio Around 0.7 - 2.0
Needle Gauge Max. 3.0 mm
Over Edge Byte 6 mm
Stitch Length Max. 3.8 mmMotor Clutch Type
No.of Needles
255 Threads Over Lock Stitch machine -
Motor, Table & Stand - Complete Set
Application Safety Stitch Machine
1 1740
Sewing Speed Min. 6000 RPM
Feed Type Differential
Differential Ratio Around 0.7 - 2.0
Needle Gauge Max. 4.8 mm
Over Edge Byte 4.8 mm
Motor Clutch Type
Warranty 3 years AMC Components to be specified
26
5 Threads Over Lock Stitch machine
with Top Feed- Motor, Table & Stand
- Complete Set
Application Safety Stitch Machine
1 5835
Sewing Speed Min. 6000 RPM
Feed Type Top Feed
Differential Ratio Around 0.7 - 2.0
Needle Gauge Max. 4.8 mm
Over Edge Byte 6 mm +
Motor Clutch Type
No.of Needles 2
Warranty 3 years AMC Components to be specified
-
8/12/2019 Elect Consumption
11/20
Page | 11
27
4 Threads Over Lock Stitch machine
with Pneumatic Back Latcher Device -
Motor, Table & Stand - Complete Set
Application Plain Over Edging - Medium Wt Knits
1 5805
Sewing Speed Min. 6000 RPM
Feed Type Differential
Differential Ratio 0.7 - 2.0 Approx
Needle Gauge Max. 4.8 mm
Over Edge Byte 8 mm
Stitch Length Max. 4 mm
Motor Servo
Features Thread Chain Cutteer & Lint Collector
Warranty 3 years AMC Components to be specified
28
4 Threads Cylinder Bed Over Lock
Stitch machine - Motor, Table &
Stand - Complete Set
Application Plain Seaming-Light to Medium Fabric
1 6444
Sewing Speed Min. 6000 RPM
Feed Type Differential
Differential Ratio 0.7 - 2.0 Approx. (Standard)
Needle Gauge Max. 4.8 mm
Over Edge Byte 8 mm
Stitch Length Max. 4 mmMotor Clutch Type
Features Thread Chain Cutter & Lint Collector
Warranty 3 years AMC Components to be specified
295 Threads Flat Lock Stitch machine
with walking foot & Left Hand Knife -
Motor, Table & Stand - Complete Set
Application Bottom Hemming Light to Medium Knit
1 1815
Sewing Speed Min. 6000 RPM
Feed Type Differential
Differential Ratio 1:0.6~1:1.5 (As Standard)
Needle Gauge 4.8 mm to 6.4 mm
Over Edge Byte 4.8 mm
Motor Clutch Type with Blower
Attachments Piping & Binding
Features Hemming Folder, Lint Collector
No.of Needles & Thread Needles 3 & Threads 5
Warranty 3 years AMC Components to be specified
-
8/12/2019 Elect Consumption
12/20
Page | 12
30
5 Threads Flat Lock Stitch machine
with Cylinder Bed - Motor, Table &
Stand - Complete Set
Application Top & Bottom Covering-Medium Wt Knit
1 6444
Sewing Speed Min. 6000 RPM
Gauge 6.4 mm
No. of Needles 3
Differential Ratio 0.5 - 1.3 (Standard)
Stitch Length Max. 4 mm
Motor Servo
Feature RequiredPneumatic/Electric Top & Bottom Thread
Trimmer
Warranty 3 years AMC Components to be specified
31
5 Threads Flat Lock Stitch machine
with Right Hand Knife - Motor, Table
& Stand - Complete Set
Application Binding Medium Wt Knits
1 9468
Sewing Speed Min. 4000 RPM
Gauge 5.6 mm
No. of Needles 3
Differential Ratio 0.5 - 1.3
Stitch Length Max. 4 mm
Motor Clutch TypeFeature Required Conversion to Top & Bottom Covering Stitch
Warranty 3 years AMC Components to be specified
32
Electric Boiler (Including Water
Softening Kit) Complete automatic &
Safety Precautions
Application To Generate Steam for 4-6 Steam table
1 4350
Power 27 kw
Pressure 3-5 Bar
Phase 3 Phase
Copper Electrodes heater of 27 KW
Vessel made of S.S.
Fully Automatic water controlling mechanism.
All safety precautions in the boiler (Mechanical as well as Electronic safetycontrol)
Warranty 3 years AMC Components to be specified
-
8/12/2019 Elect Consumption
13/20
Page | 13
33 Steam Iron
Application For Steam Press
1
9165
Size 210mm X 125mm
Teflon Shoe Cover
Steam connection from Boiler steam
Steam on / off operating through solenoid valve
Control over iron Handle.
34 Iron - Seam Buster
Application To open Seam
1
Size 190mm X 60mm
Teflon Shoe Cover
Steam connection from Boiler steam
Steam on / off operating through solenoid valve Control over iron Handle.
35 Ironing Buck For Sleeve Application To Iron Sleeve 1
36 Ironing Buck For Trouser Leg Application To Iron Trouser Seam 1
37 Ironing Buck Universal Application To Iron Shoulder Seam 2
38Stain Removing Station with 3 Guns
SS MaterialApplication Stain Removal 1 3300
39 Compressor 5HP Min 21PSI Application 21 PSI with safetyfeatures
Pneumatic Machine working and MachineCleaning
1 4401
40Stickering Gun 12 Digit Last three
Digit Moveable
Application Stickering2 372
12 degree alpha numeric Ticket Machine with Last 3 Digits Movable
41Shirt Folding Machine Pneumatically
Operated
Application Folding of Shirt
1 22200Heater for pressing the Collar
4 to 5 size Collar pressing attachment
42 Continuous Fusing Machine
Application Fusing Fabric
1 6000
TypeContinuous Fusing (Open Arm Type
Preffered)
Temerature 190-230 Degree Centigrade
Pressure Minimum 3 Kg/square cm
Belt Speed Maximun 6-9 meter/minute
Belt Width Around 450 mm-
Fusing Width Around 400 mm
Warranty 3 years AMC Components to be specified
-
8/12/2019 Elect Consumption
14/20
Page | 14
List of Machineries with Specification for TD Department.
S.No.
Items Specification Qty EMD
1 Professional DobbyRug Loom
Air-powered warp tension, Air-powered shed opening, Apron with apron rod, Dobby system (8 or12 harness) 30 dobby bars with pages, dobby peg wrench, 100 dobby chain ties, Choice ofsecond beam, Extra sturdy kiln-dried hardwood construction. Steel heddles, Reed (4, 5, 6, 8, or 10
dent), Compu-Dobby. Rug Width: 4 (1.2m). Height: 75 (1.9m), overall width: 66(1.67m), Frontto Back: 84 (2.15m), No. of Heddles: 400 or Professional Dobby Rug Loom (Vertical Punja DurryLoom)Rug width: 36, Loom width, weaving loom should be made from tick wood depending on theavailability of space within the weaving lab. Customized)
2 66000
2Hand loomJacquard
Hand Loom width: 40. Fly Shuttle facility, second back beam facility for extra warp
jacquard capacity 200 Hooks single lift single cylinder principle.1 6000
3Jacquard Loom(Electronic harnessmechanism)
Loom Width: 40, Maximum Hooks: 1200, Corresponding software Modules: (Microsoft WindowBased). Throw shuttle facility, second back beam facility for extra warp.
1 63000
4 Dobby Loom
Studio Dobby Loom. Height: 49 (124 cm), Width: 43 with Computer-Dobby software and warp
beam handle (109cm), Weaving Width: 20 (50 cm), Length: 45 with Second Beam, Foot Print:26 x 43 , Weight: 175 lbs. Harnesses: 16 or 24, Heddles: 25/ harness plus 200 extra heddles,Beater: Sidingor-Overhead, Beams: 1 or 2 Plain Beamsor-1 Sectional Beam, Microsoft WindowBased Software for the Dobby.
1 18000
5Rapier ElectronicSampling shuttle
less loom.
Loom: Weaving Width: 10-20 inches, Speed: 45 ppm maximum (with reference to fabric width or20 inches), Weft Selector: 6 clours electronic weft selection device. Maximum up to 8 colors,Fabric Take-up: Electronically controlled, Warp let-off: Positive electronically controlled,Shedding: Computerised controlled. Maximum 20 heald frames driven pneumatically by aircylinders.(1st& 2ndheald frames are for leno & selvedges), Draw-in: Heald frames can be separated from theloom for healds and reeds draw-in, Warping: separate warp beam or manual warping could both be
used, Weft Insertion: Single rapier weft insertion. Speed could be controlled independently throughthe computer, Beat-up: Computerised servo-motor controlled. Beat-up could be done in different
positions. Weft Breaks: Mechanical Weft- Break detectiong device, Warp Breaks: Photo-electric
warp-break detectiong device, Designing Built-in design and editing software, Air Consumption:580 L/min. Air pressure 6-9 kgf/sq.-cm. Power: 220V Single phase, 50-60Hz. Controller: PC based
controller/ Window XP operating system.
1 3000
-
8/12/2019 Elect Consumption
15/20
-
8/12/2019 Elect Consumption
16/20
Page | 16
18
Embroidery
Machine withsoftware andrequired
accessories
12 colors, three head, computerized embroidery machine complete set. Machine speed: 1000rpm. Embroidery Area: 1000 x 1000 mm. Power specification: Single phase, 220 Volt. Memory
capacity: 20 lakh stitches. Operation Panel: LED with Pen Drive system. Embroidery Software forfont and design editing.
1 45000
19Flock PrintingMachine
Electro Static Powder supply 230 V AC +/- 10% 50Hz., Moving Trolley, Fine Sieve, Handoperated sieve for small novelty items
1 5100
20 HTHP Lab Steamer
HTHP Lab SteamerMax. Working Pressure: 4 kg/cm2, Cloth Carrying Capacity: 20 cm x 150 cm long, internaldiameter of the vessel: 535 mm, Material of Construction: SS 304, Overall machine dimension: L
630 x W 600 X H 1150 mm, approx. weight: 65 kgs, Electric load: 41/2 kw, Electric supply: 220v,F 50 Hz.
1 4500
21Lab Jigger Dyeing
Machine
Working width 450mm and 600mmMLR 1:3 to 1:4
Temperature upto 94 CSpeed upto 6m/minDimension 1150 mm x 540 mm x 500mm
Electric Supply 230V, Single phase, 50Hz 10 AmpMaterial of construction SS 316 for Beakers Dye Bath, Other parts SS-304
1 4500
22 Motorised Stirrer 0.25 HP, RPM 6500 2 90
23 Spray Gun
Stain less steel needle.
Precision air and fluid adjustmentsNeedled and nozzle tip combination 1.0 to 1.8 mm
1 450
24 Air CompressorMotor capacity 1 HP, Motor power rating 0.75 KW, No. of Cylinder = 1 working motor rpm 1400
pressure 86-100 psi Tank capacity 70 liters.2 13500
25High Temperature,High Pressure
Glycerin Bath
Beaker Capacity, 1000 ml12 nos
Dyeing temperature 140 degree C, ml ratio 1:122 9000
26Heat Transfer
Printing MachineWidth 16 x 20 Pneumatic system for controlling pressure Temp. RT to 300 C 1 4500
Testing Lab
27Physical WeighingBalance
Weight capacity 2 kg 1 600
28ElectronicWeighing Balance(1g)
Weight: 300 gms. Least weight 0.01 mgs. 1 900
-
8/12/2019 Elect Consumption
17/20
Page | 17
29Crease RecoveryTester
To determine the crease recovery angle of any fabrics, 10N+9.63N weight supplied as per ISOStandard, 500gm weight as per AATCC Standard, with two templates for ISO & AATCCStandard, Supplied with complete accessories along with two templates for preparing sample tomeet ISO 2313 & AATCC 66 standards.
1 4500
30Shrinkage
Template and ScaleAcrylic Template & scale to meet standards ISO 3759 & BS 4931 Standards 1 4500
31 Stiffness Tester
To determine the bending modulus & Flexural rigidity of any type of fabrics, scale graduated in (0to 16) centimeter, weight 270 gms strictly meets the specification of ASTM Standards, Suppliedwith complete accessories along with two templates for preparing sample, L 11 x D 5.50 x H 8,
to meet ASTM D 1388, BSEN 22313, BS 33569073-7, IS 6490, and ERT 50-3 standards
1 4500
32Drape meter (Cusik
Principle)
Using Dr. Cusik Principle, with 14 dia parabolic mirror, sample size 30 cm dia, supporting disk
size 18 cm dia, along with a template, energy supply of 220 v1 4500
33 Digital Crock meter
Dual Metal Sample Holder for specimen Testing and Garment Testing, Complete with all
accessories including pre-cut (50 x 50 mm) 400 crocking clothes, 16 mm Finger and finger to meetthe standards of ISO 105 x 12/ D02, BS 1006 D02, AATCC 8/165
1 4500
34 Perspiration testerSupplied with 5Kg, dead weights as per ISO standards, complete with all accessories acrylic
palates, adjacent fabrics etc. L 9 x D 3 x H 7 to meet the standard ISO 105, BS 1006, IWSTM 6,174, 175, and DIN 54005, 54006, 54007, 54020 Standards
1 4500
35Bursting strengthtester
Maximum capacity 70 kgs, Pneumatically control sampleclamping with digital control, L 21 xD 17 x H 24 to meet the standards BS 3424/ 3137, ASTM D 3786/ ASTM D 774, ISO 2758/2559/ 3303/ 3669
1 4500
36Tensile StrengthTester
Maximum capacity 250 Kg with 100 gms accuracy, work on CRE principle, Digital control panel,Maximum jaw separation 450mm & minimum jaw separation 25mm, One inch & four inch jawssupplied to conduct grab test & seam slippage, Complete with all accessories templates, 6 mmgauge etc., L 27.5 x D 15.5 x H 65 to meet the standard ASTM-D 5035, ASTM-D 1578, ASTMD-5034, ASTM D-434, BSEN 1002-3, BS-1610 DIN-51221.
1 4500
37Pilling tester withaccessories
standard scale.
Standard pilling Boxes with Standard Cork Lining, with all stainless steel tubes, rubber tubes
accessories to meet ASTM 3512/ 4970/ 5362, BS 5811, ISO 12945 standards1 4500
38MartindaleAbrasion ResistantTester
Four stations to test 4 specimens at a time, 140mm & 38mm with spare blades & cutting materials,three types of load 3Kpa, 9Kpa, 12Kpa, to meet to BS, ISO & ASTM standards, Complete with all
accessories including one stainless steel marking pen to draw lissagious figure, L 28.25 x D 27.5 x H 12.25
1 4500
39Tearing Strengthtester
Capacity upto 12.800Kgs, Stainless steel body with adjustable cutting knife, three variable capacity3.200kg, 6.400kg & 12.800kg for different type of fabrics, L 20.5 x D 10 x H 22 to meet BS4253, ASTM D 1424-96, DIN 53862, and BSEN ISO 13937 standards.
1 4500
-
8/12/2019 Elect Consumption
18/20
Page | 18
40Computerized YarnCount Tester
To determine count to yarns directly in any system, Interfaced with computer to give direct count
of yarn, to give result in any system (Cotton Count, Denier, Metric, Tex Etc.), High precisiondigital balance, Capacity of the balance is 310gms & accuracy 0.001gm, Complete with allaccessories, L 12 x D 8.25 x H 7
1 4500
41Digital TwistTester
Yarn Test Length 50mm to 500 mm Adjustable* Capable for Single and Double Yarn
* S/Z Switch for Selection of Twist Type* TPM Range: Upto 9999 TPM (Direct TPM on Display)
* TPI Range : Upto 250 TPI* Resolution: One Count for TPM/ 0.25 Count for TPI
1 4500
42Fabric ThicknessGauge
Maximum capacity 10 mm & accuracy 0.01mm 1 4500
43GSM Cutter &
Balance
Maximum capacity of the weighing balance is 100gms with 0.01g accuracy. Sample cutter dimension
Dimension: Length Depth Height 260 mm 165 mm 100mm1 4500
44 Landro Meter
Temperature upto 98 C with digital temperature controller, inching facility for loading and
unloading the bekears, digital timer with automatic shutdown & audible warning, eight 550 mlbeakers & 40 rpm of the rotating drum to meet the standards ISO 105, BS 1006
1 4500
45Light FastnessTester
Specimen holder03 nos.Test tube holder for humidity control50 nos.
Water tank - 01 no.Pump - 01 no.Liquid filter (syringe)
Potassium carbonate500 gmMBTL Lamp (500 watts)01 no.
Hour meter with buzzer01 no.Voltage stabilizer01 no.Pre set timer 01 no.
SDC Grey scale for accessing change in colour & staining 01 setSDC blue standard (01-08 no.)
1 4500
46
Digital projection
microscope forfiber/yarn testingwith computer
Voltage 220 f50 single phase, Magnification power 100 x 200 x 400 x 1000 x Objective 10 x 20 x40 x 100 x stage micrometer 1MM scale wire with 0.01 mm accuracy. Personal computer 1 latestconfiguration
1 4500
-
8/12/2019 Elect Consumption
19/20
Page | 19
47Traverse threadcounter
40 x traveling microscope is attached magnify the fabrics.Inbuilt reference line inside the traveling microscope eases accurate checking.Two filament bulbs from bottom to view the sample.Complete with all accessories along with two templatesSlot Size: 10 mm, 20mm, and 50 mmSlot Size: inch, inch, and 1 inch
1 4500
48 45 degree AngleFlammabilityTester
Stainless Steel test cabinet with glass observation panel provided with automatic timing of flamespread in .1 seconds increment ignition or manual flame impingement for 15 or 20 seconds
1 4500
49Digital Crock
Meter
Size of Crocking cloth = 5 x 5 cmDiameter of finger16mm
As per AATCC & ISO standards
1 4500
50 Magnetic Stirrer
Plate area: 7 x 7 approx.
Max, Plate surface temperature: Approx 520CStirring speed range: Approx. 1001500rpm230 Volt 1 KW voltage
1 4500
51 Digital Hygrometer
Temperature measuring range: -50 + 70 (-58158), Moisture measuring range: 10% 99% RH, Max/
Min temperature and moisture displayAccuracy: 1, 5%Max/ Min temperature and moisture display
Accuracy: 1, 5%
1 4500
52SublimationFastness Tester
Power requirements: 220 V AC, 65 watt
Temperature range for test : upto 250CTemperature settings: variable temp setting on each padPower readout: Digital display for each pad.
Number of heating stations: 3Total number of pads: 6 heating pads, 2 for each heating station, with individual heating
Size of each pad: 40 mm x 100 mm
Timer range: 0-60 Sec.Machine dimensions: 38 cm(w) x 34 cm. (d) x 28 (h)
Machine weight : 16-200kg
1 4500
53Computer ColorMatching System.
Dual-beam spectrophotometer
Illumination SourcePulsed xenon filtered to approximate D65 Wavelength Range360 nm to 700 nm Reporting Interval10 nm Blac TrapHigh performance Lens3 position auto zoom UV calibrationoptional
1 24000
-
8/12/2019 Elect Consumption
20/20