EIKI Projector RST RT RM User Manual

8/12/2019 EIKI Projector RST RT RM User Manual

1/20

Disclaimer

The information contained in this Adobe PDF file is for general information purposes only.Due to the age of the information and the difficulty in converting it to computer formats itmay not be up to date or correct, we make no representations or warranties of any kind,

express or implied, about the completeness, accuracy, reliability, suitability or availabilitywith respect to the Adobe PDF or the information, products, services, or related graphicscontained in the Adobe PDF document for any purpose. Any reliance you place on suchinformation is therefore strictly at your own risk.

n no event will we be liable for any loss or damage including without limitation, indirect orconse!uential loss or damage, or any loss or damage whatsoever arising from loss of dataor profits arising out of, or in connection with, the use of this Adobe PDF.

This document is available free from cineinformation.org.
http://www.cineinformation.org/http://www.cineinformation.org/


2/20

flIRST / RT / RM Series X

6mmProjectorsOPERATOR S M A N U A L

ELF AUDIOViSUAL LIMITE836Yebv iJRoad Trading Estate Slough Berks


3/20

ICAUTION IThese instructions incorporate safety recommendationswhich should be read before the projector is used, butnote especially Connect the projector to AC mains supply using a three-pin plug to ensure that the chassis is properly earthed.Disconnect plug from mains socket before the rearcover secured with screws is removed or the lampschanged.

Green and Y e ll ow__ _to Earth rown to Live lue toNeutral

In due courseplugs w bemarkedonlyE or theelectricalsymbol fo r arth: :l ; and N.


4/20

LF RST RT RM Series XSimple Operation

asy MaintenanceTrouble free Use

This Operator s Manual is easy-to-read, informative and helpful.le se read carefully before operating projector for the first time.

ONTENTS ge

Main Parts of Your Projector 2Explanation of Switch Plate 3Focusing . 4Threading (RST Model) 5Threading RT Model) Threading (RM Model) 7Projection 8Rewinding 9Changing Lamp 10Silent Film Speed 11Mag-Opt Projection 12Spare Parts Accessories 13Trouble Shooting 14Cleaning Maintenance 15General Specifications 16


5/20

2M N PARTS OF YOUR PROJECTOR

@@@

@

[ Model RST-3 ]

1. Handle2 rm Lock3 Supply rm4 Film Channel Rewind Lever5. Stil1 Picture Lever6 Focus Knob 7 Inching Knob8. Lens9. Framing Lever

10 Pilot Lamp11. Automatic ThreadlnqControl Lever RSTiRT12. Film Trimmer RSTIRT13. Switch Plate14. Elevator Knob15. Power Cord16 ,Take-up rm17 Lamp House18. Auto Take-up Guide RST


6/20

EXPLANATION OF SWITCH PLATEModel RST / RT / RM O 1

Model RST / RT / RM 2

3

Model RST / RT / RM

All Models1. Lamp Low Reverse)2. Reverse3. Off4. Forward5. Lamp Low Forward)6. Lamp High )7. MIC Input8. Volume mp Switch9. Treble Control10. ss Control

Additional on RST / RT / RM 211. Magnetic Playback12. Optical Playback

Additional on RST / RT / RM13. Recording Lock utton14. Recording15. PHONO Input16. Level Indicator


7/20


8/20

5THRE DING FULLY UTOM TIC THRE DING REEL-TO-REELMODELS RST O 1, 2, 3

A1. Place ELF AUTO REELon take-up arm.

Insert film in trimmer andcut with raised end.Photo A

2. Turn ROTARY SWITCH toFORWARD position


9/20

_THREADING / SELF THRE ING MODELS RT O 1 2 3

A

1. Insert film in trimmer andcut with raised end. Photo A)

2. Turn ROTARY SWITCH toFORWARD position ).

3. Push automatic threadingcontrol lever to SELF-THRE D / position.Photo B).

4. Insert film leader into Filmchannel. Film threads automatically. When a gentletug is applied to film comingoff last roller, the automaticthreading guides wi II release

Photo C)5. When sufficient film has

passed through projector toreach take-up reel, SWITCHOFF 0 ).

6. Attach leading edge of filmon to take-up reel.

c


10/20

THREADING M NU THREADING MODELS RM O 1 2 3

1. Swing lens away from projector by pulling on lensholder. Photo A

8

2. Open both sprocket shoes.and rubber roller. PhotoA, B

3. Thread fi lmTHREADING

followingDIAGRAM.Raise rubber guide roller as

necessary

4. Close both sprocket shoesand lens holder.

5. Be sure film is seated properly in gate.

c6. Check threading by turninginching knob. When knob isturned by pushing UP filmshould move forward intermittently in film gate andboth upper and lower loopswill be maintained.Photo C

7. Attach leading edge of film on to take-up reel


11/20


12/20

9R WIN ING

A1. ttach tail end of film to supply

reel.2. Move rewind lever DOWN to RE-WI NO posit ion photoA .and turnROT RY SWITCH to FORW RDposition . fter rewinding FIRST return rewind lever UP to OPER TE position and turn ROT RY SWITCHto OFF position .

itRewindingIReturn rewind lever UP

to OPERATE ~B

3. fter removing reels from armsdepress arm locking buttonsphoto B and lower arms

4. Replace projector cover to carry.The flexible plastic cover should beused to protect projector and tocarry take-up reel spare lampspeaker cord etc.


13/20

10CHANGING LAMPSIS ONNE T POWER SUPPLY OR

Remove lamp-house lock screw near the top of aperture plate.Pullout on top edge of lamp-house.

PROJECTION LAMP e ] ~ ELC/24V 250WPush to left ejection lever immediately below lamp and lampwill come out photo A . Be sure replacement lamp snaps intoplace. Proper seating of lamp is essential.

EXCITER LAMP SRK/4V O.75APullout on black exciter lamp cover photo B .Push in on lamp and turn counter-clockwise to remove.Insert new lamp with notch on base flange in upper right position.turn clockwise clean fingerprints from lamp and replace cover.Close lamp-house door and replace lock-in screw.


14/20

SIL NT LM SP

IS ONNE T POWER SUPPLY OR

Shutter

SOUND

Motor

SI LENTShutter oV

Motor

This is changed by slipping the motor drive belt to the alternateset of puIleysOpen rear cover. Turn inching knob at the same time guidingthe belt first to the smaller motor pulley then to the largershutter pulley. Change back to sound speed by reversing theabove procedure.

Note. No silent speed on 5 6 Hz models.


15/20

12MAG-OPT PROJECTIONOn the RST-2, 3, RT-2, 3, RM-2, 3 Models, either magnetic oroptical sound tracks may be played back.

MAGNETICPLAYBACK

OPTICALPLAYBACK

RECORDING ON MAGNETIC STRIPED FI LMRST/RT/RM-3 Models

M ~1. Put OPT-MAG knob to the Optical position and

thread film in the projector in the normal manner, MAGNETICthen set the knob to Recording position. RECORDING2.Connect the supplied microphone or any 50k Ohm impedance

microphone to the MIC input on the Amplifier Controlpanel. A record player or tape recorder may be plugged intothe PHONO input.

3. Depress the small silver Safety Recording Lock Buttonbelow the function switch and turn the three-position functionswitch to record R).

4. Adjust the Volume Control to obtain the proper recordinglevel as indicated on the record level indicator.The best recording level is obtained when the needle justtouches the red line. If the needle is allowed to swing intothe red area, the recorded sound may be distored.

5. Run the film, watch the screen, record your voice or musicon the film.

6. Playback - rewind film, turn funct ion switch to the magneticplayback position M , disconnect microphone or tape recorder - run film and check the quality of the sound justrecorded.

7. A magnetic sound track may be er se by running the filmthrough the projector with the function switch in R andthe Volume Control in the minimum position and the MICdisconnected.


16/20

RECOMMENDED SPARE PA RTS ACCESSORIES

PROJECTION LAMP - ELC/24V, 250W

EX CITER LAMP - BRK/4V 0.75A

FUSE/2A with holder large)

ANAMORPHIC LENS

ANAMO RPHI C LENS HOLDER

FUSE/2A with holder small)

13

LOWa

HIGH

LAMP HI-LOW SWITCH for maximumlife)By switching to LOW position yourlamp will last 3 times longer and evenin this LOW position the lamp outputwill be min imum 550 lumens.The HIGH position


17/20

TROUBLE SHOOTING ere IS anon Proresslonal/s gUIde for /oca t rtq r or o roo/ernsIn nearly every case a simple aefjustment all that IS necessaryto restore p k efficIency.NO POWER TO MOTOROR LAMP

MOTOR RUNS, BUT PROJECTION LAMP DOESNOT LIGHTFILM DOES NOT RUN,BUT MOTOR ANDLAMP BOTH OPERATENO SOUND

POOR SOUND

POOR PICTURE

Make sure power cord is connected to wall outlet and thatoutlet has power.

2. Check power cord and repair ifnecessary.

Check position of rotary switch.2. Replace projection lamp. Raise STILL PICTURE

LEVER to operate.2. Check Motor Belt. Turn amplifier switch on andincrease volume.

2. Plug in speaker. On modelswith removable speaker.)

3. On models with magnetic reproduction be sure I M-Oswitch is in proper position.

4. Replace exciter lamp if lampdoes not light.

5. Check 2 A fuse replace ifnecessary.1. Check position of volume con-

trol.2. Rethread film.3. Clean exciter lamp.4. Fi may be defect ive, use new

film if necessary. Check threading, rethread ifnecessary.

2. Clean projection lens with softtissue, both front and rear.

3. Refocus lens.4. Clean gate with soft bristle brush.5. Film may be defect ive, use new

film if necessary.


18/20


19/20

16

GENERAL S P I F I ~ T I O N S

RST Models Reel-to-Reel Automatic ThreadingRT Models Self ThreadingRM Models Manual ThreadingPOWER AC. 50 or 60 Hz., 430 - 450WLENS super 50mm 2 ) f1.2 standardPROJECTION LAMP ELC Halogen lamp, 24V - 250W200W lamp also usableEXCITER LAMP BRK, 4V-0.75AAMPLIFIER solid state, 25W RMS output

separate treble and ss controlsindependent use for public addressMOTOR induction motor, plug-in typeFRAMES PER SECOND 24 and 18 sound and silentSPEAKER 13cmx20cm 5 x8 ) .

RST, RT, RM-O16cm round 6.5 )

RST, RT, RM-1, 2, 3REVERSE PROJECTION. yesSTI LL PICTURE. yesLOOP RESTORE R. automaticREWIND. high speed, without reel changeREE L CAPACITY. 600m 2,000 tt)MODU LAR UN ITS . amplifier, cam tank, motor,lens holder, transformerWEIGHT . 17 Kgs. 37.4Ibs.)DIMENSIONS 29cmx35cmx35cm 11.4 x 13.8 x13.8 )

with front cover

ELF AUDIO VISUAL LIMITED,836 Yeovil Road, Trading Estate, Slough, Berks.

Telephone: Slough 36123/5


20/20

EIKI Projector RST RT RM User Manual

Documents

Transcript of EIKI Projector RST RT RM User Manual