EGI Industries provides the following coating materials · HVAF is a warm spray process that is...
Transcript of EGI Industries provides the following coating materials · HVAF is a warm spray process that is...
COATING PROCESSES FOR MECHANICAL PARTS IN NORTH AMERICA
Ceramics
This ultra-high-temperature system facilitates the application of ceramics and other materials.Ceramic coatings have excellent properties against corrosion andhigh temperature.
We repair and reconstitute metallic parts according to mechanical application tolerances. Our laboratory research and development allows us to design innovative spray processes
to provide more durable coatings with consistent quality.
EGI Industries provides the following coating materials:
Alumina oxide
Zirconium oxide
Chromium oxide
Titan oxide and other
Metals
Stainless steel
Aluminum
Copper
Brass and bronze
Hard metals
The processes we offer cansolve all kinds of wear:
Abrasion
Erosion
Friction
Corrosion
Cavitation
Insulation or electrical conductivity and otherCarbides
Tungsten carbide coatings
Chromium carbide coatings and other
HVAF PROJECTION
All types of process can use metal coatings, depending on what mechanical properties you want for your parts. However, HVAF projection allows the densest coatings on the market, exceeding conventional HVOF systems.
WIDE RANGE OF CARBIDE AND METAL COATINGS
These coatings are used to rebuild worn parts. It is also possible to rebuild a part using a metal coating, then apply a carbide finish.
METALLIZATION WITH METALLURGICAL LINKS
Through this process, we have the ability to create more flexible metallic coatings that can withstand wide temperature variations while maintaining excellent properties against corrosion and abrasion.
[email protected] WWW.EGIINDUSTRIES.COM
CONTACT US
SPECIALTY COATINGS
We are committed to developing innovative solutions for your coating requirementsand providing the highest quality coating tailored to your specific applications.
Foam
Closed cell Neoprene Foam
Closed cell Latex Foam
Closed cell Polyurethane Foam
DuPont™ Teflon®
PTFE
PFA
FEP
ETFE
Teflon S
Other
Xylan®
Halar® ECTFE
Phenolic
Carboline
Rilsan
Plastisol
Polyarmor
Plastcoat
Powder Coatings
Vinyl PVC
High Temperature Ceramic
etc…
BEFOREAFTER Success in rebuilding and re-certifying mining Valves and Pump rebuildsto higher standards than the manufacture.
Reproducing mobile equipment parts for major OEM to a higher quality standard using the latest in specialty antiware coating that exist.
Our Teflon coating on agitators are FDA food grade approved and leaveno transfer to your solution in your tanks
Our Teflon protects your agitator shafts against any chemicals
Save your equipment and reduce replacement costs with EGI
EGI INDUSTRIES 4670 AVE THIBAULT SAINT HUBERT, QUEBEC J3Y 0A8 514-316-3444/[email protected]/egiindustries.com EGI Industries usa 1 Cumberland Ave Plattsburgh, NY 12901/929-357-3126/ [email protected]/egiindustries.com
EGI HVAF Process Overview HVAF: High Velocity Air-Fuel Description HVAF or High Velocity Air-Fuel is a thermal spray process for deposition of coatings for protection of parts, vessels and structures against abrasion, erosion and corrosion. Common uses:
• abrasion protection • chemical resistance • erosion protection • corrosion protection • surface restoration • diameter build-up • spraying of internal diameters of pipes • thin layer surface alteration to prepare for other processes such as galvanization • surface preparation by cold or hot grit blasting • coating stripping by hot grit blasting
EGI HVAF PROCESS HVAF is a warm spray process that is cooler than HVOF. Our guns utilize axial powder injection into an air-fuel jet with a temperature of about 1800-1980°C. Therefore, the process is capable of effectively applying carbide-based materials, the HVAF process can also apply metals with almost zero oxidation. All common thermal spray powder materials may be applied with HVAF. Different coatings, Powders and Deposits: EGI HVAF can apply metal, carbide, and metal alloy powders of 5 to 53 micron range, with -30+10 µm cut being the most common. The deposit efficiency (D.E.) is 50-75% for carbide powders, and 60-85% for metal powders. Spray rates and specifications: HVAF process is capable of spray rates of up to 40 kg/h of carbides, and up to 33 kg/h of metal powders. Tungsten Carbide Application Tungsten carbide and Ceramics are the predominant material applied by HVAF for abrasion wear and Chemical resistances. With -30+10 µm powder cut, coating hardness of up to 65-90 RCW.
EGI INDUSTRIES 4670 AVE THIBAULT SAINT HUBERT, QUEBEC J3Y 0A8 514-316-3444/[email protected]/egiindustries.com EGI Industries usa 1 Cumberland Ave Plattsburgh, NY 12901/929-357-3126/ [email protected]/egiindustries.com
Wear and Chemical Resistance: Tungsten carbide and ceramics (86WC-10Co-4Cr) HVAF coatings demonstrated 90-185% higher wear resistance when compared to regular cold thermal sprays.
Bonding Strength HVAF coatings generally have very high bond strength. For HVAF-sprayed WC-based coatings, with or without grit blasting, the typical bond strength exceeds 12,000 PSI, which is the limit of regular glue adhesion bond strength testing equipment. EGI HVAF coating bond strength is not conventionally measurable due to preliminary glue failure in normal testing equipment. Alternative braze adhesion bond strength testing was developed, which determined the bond strength of HVAF-sprayed Inconel 918 to be 31,000 PSI (200Mpa).
Fatigue, Impact and Stress Resistance A notable characteristic of our HVAF coatings is the resistance to stress-induced delamination. Coatings are non-brittle and are capable of withstanding significant mechanical deformation, as high bond strength to substrate prevents peel off. In many cases thermal spray is applied manually, this technology does peal off as the coatings have not fused to the parts as done with our automated HVAF machinery. In testing
EGI INDUSTRIES 4670 AVE THIBAULT SAINT HUBERT, QUEBEC J3Y 0A8 514-316-3444/[email protected]/egiindustries.com EGI Industries usa 1 Cumberland Ave Plattsburgh, NY 12901/929-357-3126/ [email protected]/egiindustries.com
substrates with tungsten carbide coatings were bent at 90° over 0.5" diameter, yielding no coating delamination. In alternative tests, coated samples were stretched to failure. Impact Resistance
As with fatigue and stress testing, HVAF coatings exhibit very good impact resistance. In an impact test a 1 lb steel ball was dropped from a height of 5 feet. Typically HVOF and supersonic plasma can withstand 18-22 hits before failure, as shown in plasma WC/20Cr3C2/7Ni coating on the left. On the right is an HVAF with our coating sprayed with our spray gun withstood 100 hits and the test was stopped. Permeability The Tungsten carbide based and chrome carbide based HVAF coatings sprayed with HVAF system were determined to be impermeable in 15,000 PSI gas-permeability testing, as sprayed. Coating Thickness Carbide HVAF coatings can be routinely deposited to 1000 µm thickness, with up to 40-50 µm applied per pass. In testing up to 12,000 µm coatings were achieved with tungsten carbide. Metals can routinely be applied to 8000 µm thickness or more, with 100 µm applied per pass. The photograph below shows a 8mm thick tungsten carbide coating.
EGI INDUSTRIES 4670 AVE THIBAULT SAINT HUBERT, QUEBEC J3Y 0A8 514-316-3444/[email protected]/egiindustries.com EGI Industries usa 1 Cumberland Ave Plattsburgh, NY 12901/929-357-3126/ [email protected]/egiindustries.com
Resistance to High Contact Loads Our coatings sprayed with our spray system can withstand 3.5GPa contact pressure, which is 75% higher compared to what the other best coatings could provide in comparative testing.
Corrosion Resistance EGI HVAF coatings can be corrosion resistant "as sprayed" with no additional sealant application.
EGI INDUSTRIES 4670 AVE THIBAULT SAINT HUBERT, QUEBEC J3Y 0A8 514-316-3444/[email protected]/egiindustries.com EGI Industries usa 1 Cumberland Ave Plattsburgh, NY 12901/929-357-3126/ [email protected]/egiindustries.com
Coating Internally (I.D) Our HVAF spray guns can shoot as small as 55 mm can apply coatings to internal diameters of pipes and parts as narrow as 80 mm. With no inherent restriction on length, pipes as long as 80 ft and more can be internally coated.
Everything is produced in North America under the
highest quality standards and
services you deserve and can depend on.
CALL US TODAY AND SEE THE DIFFERENCE!
4670 Ave Thibault, Saint Hubert, Quebec, Canada J3Y 0A8 +1 514 316 3444
1 Cumberland Ave Plattsburgh, NY 12901 USA+1 518 578-1775
Botswana-Angola-Mozambique-DRC Congo, Zambia, Zimbabwe: +267 71 413 511Plot 39 Unit 2 Gaborone InternationalCommerce Park, Gaborone, Botswana
Ghana, Mali, Cote d'ivoire, Sierra Leon, GuineaThokey House | Box CO 1384 | Tema - Ghana+233 244 333 792