eduard P-51D interior late ser.20-35 S.A. 32 715 · 2019. 10. 30. · 1/3 P-51D interior late...
Transcript of eduard P-51D interior late ser.20-35 S.A. 32 715 · 2019. 10. 30. · 1/3 P-51D interior late...
1/3
P-51D interior late ser.20-35 S.A.
32 715
32 7151/32 scale detail set for kit • sada detailù pro model Tamiya 1/32 Tamiya
ORIGINAL KIT PARTSPÙVODNÍ DÍLY STAVEBNICE
PHOTO-ETCHED PARTSLEPTANÉ DÍLY
PARTS TO BE REMOVEDDÍLY K ODSTRANÌNÍ
FILLTMELIT
eduard
REMOVEODSTRANIT
OPTIONVOLBA?REPLACENAHRADIT
BENDOHNOUT
GRINDOBROUSIT
SYMETRICAL ASSEMBLYSYMETRICKÁ MONTÁŽ
DRILL HOLEVRTAT OTVOR
APPLY EXPRESS MASK AND PAINT BEFORE GLUINGPOUŽÍT EXPRESS MASK NABARVIT PRED SLEPENÍM
=
1
2
4542
49
6
41412 pcs.
34
24
40
43 30
29
44
57
L16
D31
62
62
D46
74
76
68 69
D19, D21
=
6070
D23
73D16
65
D42
D53
71
71
50
D15
52
52
19
19
D23
?
4
3
48
D48
5413 pcs.
2/3 32 715
A B
C
8
7
47
28
56 plastic
- 1mml - 1,8mm
11
79
58
59
22
23
61
61
662 pcs.
D43
910
46
14
16
1720
21
D17
?13
12
49
D1
33
53
53
54
55
=
D5
39
D6, D13
31
38
35
D11
26
27
D12
3632
18
15
D35
72 - 1mml - 1,8mmplastic
plastic- 1mm
l - 1,8mm
A
B
C
3725
51
51
63
64
D36
67
78 77
D25, D26,L13,L14, L15
a 29
75
Q8
Q9
b 8
Made in Czech RepublicEduard M.A. © 2011 www.eduard.com
2. Do not inadvertently place etched componets on an unwanted surface. Attempts to remove will result in damage to your part.
2. Nepokládejte samolepící díly na volné plochy. Pokud je omylem pøilepíte, pøi pokusu o odlepení dojde k poškození dílu.
1. Separate the etched components from their frames on the protective paper. Removal from the paper is done only after separation of the parts from the frames.
1.Samolepící díly oddìlujte od rámeèku na podkladovém papíøe. Po oddìlení je sejmìte z krycího papíru.
3. Do not touch the adhesive areas of the etched components.
3. Nesahejte na èásti dílù, na kterých je naneseno lepidlo.
4. Hold the parts by the edges, or at areas free of adhesive.
4. Samolepící díly berte za hrany nebo za èásti, na kterých není nanesené lepidlo.
5. Lightly place the component in the desired location and position. Adjust as required. The component will by permanently affixed when pressed onto its intended location, its location can be adjusted.
5. Díl lehce položte do pozice, ve které má být nalepen. Upravte pøesnou pozici a pøimáèknìte. Díl dokonale pøilne až po pøimáèknutí, pøed pøimáèknutím lze dílem opatrnì manipulovat.
PARTS WITH GLUE DÍLY OPATØENÉ LEPIDLEM
3/3 32 715
(not included in this set)
eduardFor further detail sets look for 32 721 P-51D gun bay late(not included in this set)
eduardFor further detail sets look for 32 731 P-51 seatbelts(not included in this set)
eduardFor further detail sets look for 32 307 P-51D engine
eduardFor further detail sets look for 32 302 P-51D exterior (not included in this set)