Gas Separation Products

S E R I E S 9 5 G A S S C R U B B E R S amp S E P A R A T O R S

Economically Efficient

Bulk Liquid Scrubbers amp

Separators

E N G I N E E R E D F I L T R A T I O N S O L U T I O N S SM

The PECOFacet Series 95SV Scrubber provides an efficient yet inexpensive means of liquid removal during high liquid loading and slugging

APPLICATIONS

bull Compressor Suction bull Plant Entrance bull Well Head bull Contact Tower Inlet amp Overhead

C Y C L O T U B E reg S C R U B B E R

Utilizes thePECOFacet S E R I E S Cyclotube Mist Eliminator 95SV Cyclotube technology is specifically designed to enhance separation of contaminants that foul plug or creep through vane and wire mesh mist eliminators

Use Cyclotube Technology for Trouble free removal of the following contaminants bull Brine bull Lube oil bull Wax bull Glycol bull Asphaltenes

P r i n c i p l e o f O p e r a t i o n Bulk contaminants and slugs diverge from the gas stream upon entering the scrubbers first stage and are collected in the lower sump below the PFDBS Following a tortuous path the gas and entrained contaminant enter the scrubbers second stage where Cyclotube separators combine centrifugal pressure vacuum and flow vector forces to effect highly efficient separation while velocity scouring inherent in Cyclotube dynamics precludes fouling The removed contaminant is collected in an independent second stage sump Low differential pressure cyclotubes are available for pressure sensitive applications

Gas and entrained contaminant enter

cyclotubes

Inlet

Bulk contaminants and slugs collect in

lower sump

Entrained contaminat removed by Cyclotube

Contaminant collects in the 2nd stage sump

Outlet

PECOFacet Flow Distribution Baffle Screen (PFDBS) - Minimizes GasLiquid

Contact Area - Reduces rate of

evaporation - Prevents

Re-entrainment - Creates a stable

environment for invasive control equipment

V A N E S C R U B B E R

Utilizes both the PECOFacet Gas and entrained S E R I E S Wave Plate and Hook Vane liquids enter vane Mist Eliminators Outlet 95SV

Vane mist eliminators effectively remove water hydrocarbon liquid and Liquids drain

typical pipeline liquid mixtures via drain leg to lower sump

Inlet

P r i n c i p l e o f O p e r a t i o n Bulk contaminants and slugs diverge from the gas stream upon

PECOFacet Flow Distribution entering the scrubbers first stage and are collected in the sump Baffle Screen (PFDBS) area below the PFDBS Following a tortuous path the gas and - Minimizes GasLiquid entrained contaminant enter the scrubbers second stage where Contact Area

- Reduces rate of evaporation

PECOFacet vane technology utilizes inertial impaction to separate contaminants from the gas stream The removed contaminant

- Prevents then gravity drains into the sump via the drain leg preventing Re-entrainment re-entrainment Liquid Slugs fall - Creates a stable

into lower sump environment for invasive control equipment

PECOFacet 95V Separators are a single stage vertical unit design for a continuous light liquid load when no slugs will be present

APPLICATIONS

bull Compressor Discharge bull Compressor Interstage bull Vent Gas bull Cooler Discharge bull Steam

bull Meter amp Regulation Stations

Entrained liquids removed by the

Cyclotube

Liquids collect in the sump

Outlet

C Y C L O T U B E reg S E P A R A T O R

S E R I E S 95V-CT P r i n c i p l e o f O p e r a t i o n

The principle of operation is similar to that described for the 95SV Cyclotube scrubber except there is no first stage pre-separation of bulk contaminants and slugs prior to entering the Cyclotube separators The gas and contaminant directly enter the scrubbers Cyclotube separators which combine centrifugal pressure vacuum and flow vector forces to effect highly efficient separation while velocity scouring inherent in Cyclotube dynamics precludes fouling The removed contaminant is collected in a sump compartment located below the Cyclotube contaminant ejection ports Low differential pressure Cyclotubes are available for pressure sensitive applications This Separator should be used for medium liquid and solids loadings

Entrained liquids removed by the Vane

Liquids load from the bottom of the Vane

Liquids collect in the sump

Inlet

V A N E S E P A R A T O R

S E R I E S 95V-Inline Outlet

P r i n c i p l e o f O p e r a t i o n The principle of operation is similar to that described for the 95SV vane scrubber except there is no first stage pre-separation of bulk contaminants and slugs prior to entering the vane separator The gas and entrained contaminant directly enter the vane which utilizes inertial impaction to separate contaminants from the gas stream The removed contaminant then gravity drains into the sump This Separator should be used for light liquid loading with minimal solid contaminant loading

Information Required for Sizing Related configurationsproducts offered

bull Operating Pressure bull Horizontal Configuration bull Operating Temperature bull Alt-Line Configuration bull Gas Specific Gravity bull 3-Phase Separators bull Gas Flow Rate at above Conditions bull Multi-Cyclone Separators bull Contaminant bull Wire Mesh Separators bull Contaminant Flow Rate bull Removable Vane Packs bull Design Pressure bull Mist Eliminators also Sold Separately bull Corrosion Allowance

All PECOFacet Vane Mist Eliminators are built in accordance with ASME code for unfired pressure vessels national board stamp and local state and province require-ments as specified

Standard PECOFacet Vane Mist Eliminators are of welded carbon steel bodies with either carbon steel or stainless steel vane elements

PECOFacet is a world leader in the design and manufacture of quality Filtration Equipment specializing in the Oil and Gas Industry Founded in 1936 many of the technologies used in the Industry today were originally developed by PECOFacet Our continued dedication to research and development of new leading edge technologies has kept PECOFacet at the forefront of Engineered Filtration Solutions for use by our clients worldwide Our vast experience and knowledge of Oil amp Gas related applications allow us to offer not only Filtration Solutions but also Process Solutions

Consult factory for custom units including horizontal configurations and 3-phase separators

Your local

distributor

Corporate Headquarters

PO Box 640

Mineral Wells Texas 76068

Phone 8008777326

9403252575

Fax 9403254622

e-mail elementspecofacetcom

web site wwwpecofacetcom

Locations

Almere The Netherlands

Calgary Canada

Cedex France

Bergamo Italy

Beijing China

Bucharest Romania

Houston Texas

Kempen Germany

Kuala Lumpur Malaysia

La Coruna Spain

Manama Bahrain

Mid Glamorgan UK

Queretaro Mexico

Stillwell Oklahoma

Thetford UK

Torino Italy

Tulsa Oklahoma

Please refer to wwwpecofacetcom for most current literature edition

FS-95-SL-01 (LHA 1108) Printed in USA

The PECOFacet Series 95SV Scrubber provides an efficient yet inexpensive means of liquid removal during high liquid loading and slugging

APPLICATIONS

bull Compressor Suction bull Plant Entrance bull Well Head bull Contact Tower Inlet amp Overhead

C Y C L O T U B E reg S C R U B B E R

Utilizes thePECOFacet S E R I E S Cyclotube Mist Eliminator 95SV Cyclotube technology is specifically designed to enhance separation of contaminants that foul plug or creep through vane and wire mesh mist eliminators

Use Cyclotube Technology for Trouble free removal of the following contaminants bull Brine bull Lube oil bull Wax bull Glycol bull Asphaltenes

P r i n c i p l e o f O p e r a t i o n Bulk contaminants and slugs diverge from the gas stream upon entering the scrubbers first stage and are collected in the lower sump below the PFDBS Following a tortuous path the gas and entrained contaminant enter the scrubbers second stage where Cyclotube separators combine centrifugal pressure vacuum and flow vector forces to effect highly efficient separation while velocity scouring inherent in Cyclotube dynamics precludes fouling The removed contaminant is collected in an independent second stage sump Low differential pressure cyclotubes are available for pressure sensitive applications

Gas and entrained contaminant enter

cyclotubes

Inlet

Bulk contaminants and slugs collect in

lower sump

Entrained contaminat removed by Cyclotube

Contaminant collects in the 2nd stage sump

Outlet

PECOFacet Flow Distribution Baffle Screen (PFDBS) - Minimizes GasLiquid

Contact Area - Reduces rate of

evaporation - Prevents

Re-entrainment - Creates a stable

environment for invasive control equipment

V A N E S C R U B B E R

Utilizes both the PECOFacet Gas and entrained S E R I E S Wave Plate and Hook Vane liquids enter vane Mist Eliminators Outlet 95SV

Vane mist eliminators effectively remove water hydrocarbon liquid and Liquids drain

typical pipeline liquid mixtures via drain leg to lower sump

Inlet

P r i n c i p l e o f O p e r a t i o n Bulk contaminants and slugs diverge from the gas stream upon

PECOFacet Flow Distribution entering the scrubbers first stage and are collected in the sump Baffle Screen (PFDBS) area below the PFDBS Following a tortuous path the gas and - Minimizes GasLiquid entrained contaminant enter the scrubbers second stage where Contact Area

- Reduces rate of evaporation

PECOFacet vane technology utilizes inertial impaction to separate contaminants from the gas stream The removed contaminant

- Prevents then gravity drains into the sump via the drain leg preventing Re-entrainment re-entrainment Liquid Slugs fall - Creates a stable

into lower sump environment for invasive control equipment

PECOFacet 95V Separators are a single stage vertical unit design for a continuous light liquid load when no slugs will be present

APPLICATIONS

bull Compressor Discharge bull Compressor Interstage bull Vent Gas bull Cooler Discharge bull Steam

bull Meter amp Regulation Stations

Entrained liquids removed by the

Cyclotube

Liquids collect in the sump

Outlet

C Y C L O T U B E reg S E P A R A T O R

S E R I E S 95V-CT P r i n c i p l e o f O p e r a t i o n

The principle of operation is similar to that described for the 95SV Cyclotube scrubber except there is no first stage pre-separation of bulk contaminants and slugs prior to entering the Cyclotube separators The gas and contaminant directly enter the scrubbers Cyclotube separators which combine centrifugal pressure vacuum and flow vector forces to effect highly efficient separation while velocity scouring inherent in Cyclotube dynamics precludes fouling The removed contaminant is collected in a sump compartment located below the Cyclotube contaminant ejection ports Low differential pressure Cyclotubes are available for pressure sensitive applications This Separator should be used for medium liquid and solids loadings

Entrained liquids removed by the Vane

Liquids load from the bottom of the Vane

Liquids collect in the sump

Inlet

V A N E S E P A R A T O R

S E R I E S 95V-Inline Outlet

P r i n c i p l e o f O p e r a t i o n The principle of operation is similar to that described for the 95SV vane scrubber except there is no first stage pre-separation of bulk contaminants and slugs prior to entering the vane separator The gas and entrained contaminant directly enter the vane which utilizes inertial impaction to separate contaminants from the gas stream The removed contaminant then gravity drains into the sump This Separator should be used for light liquid loading with minimal solid contaminant loading

Information Required for Sizing Related configurationsproducts offered

bull Operating Pressure bull Horizontal Configuration bull Operating Temperature bull Alt-Line Configuration bull Gas Specific Gravity bull 3-Phase Separators bull Gas Flow Rate at above Conditions bull Multi-Cyclone Separators bull Contaminant bull Wire Mesh Separators bull Contaminant Flow Rate bull Removable Vane Packs bull Design Pressure bull Mist Eliminators also Sold Separately bull Corrosion Allowance

All PECOFacet Vane Mist Eliminators are built in accordance with ASME code for unfired pressure vessels national board stamp and local state and province require-ments as specified

Standard PECOFacet Vane Mist Eliminators are of welded carbon steel bodies with either carbon steel or stainless steel vane elements

PECOFacet is a world leader in the design and manufacture of quality Filtration Equipment specializing in the Oil and Gas Industry Founded in 1936 many of the technologies used in the Industry today were originally developed by PECOFacet Our continued dedication to research and development of new leading edge technologies has kept PECOFacet at the forefront of Engineered Filtration Solutions for use by our clients worldwide Our vast experience and knowledge of Oil amp Gas related applications allow us to offer not only Filtration Solutions but also Process Solutions

Consult factory for custom units including horizontal configurations and 3-phase separators

Your local

distributor

Corporate Headquarters

PO Box 640

Mineral Wells Texas 76068

Phone 8008777326

9403252575

Fax 9403254622

e-mail elementspecofacetcom

web site wwwpecofacetcom

Locations

Almere The Netherlands

Calgary Canada

Cedex France

Bergamo Italy

Beijing China

Bucharest Romania

Houston Texas

Kempen Germany

Kuala Lumpur Malaysia

La Coruna Spain

Manama Bahrain

Mid Glamorgan UK

Queretaro Mexico

Stillwell Oklahoma

Thetford UK

Torino Italy

Tulsa Oklahoma

Please refer to wwwpecofacetcom for most current literature edition

FS-95-SL-01 (LHA 1108) Printed in USA

PECOFacet 95V Separators are a single stage vertical unit design for a continuous light liquid load when no slugs will be present

APPLICATIONS

bull Compressor Discharge bull Compressor Interstage bull Vent Gas bull Cooler Discharge bull Steam

bull Meter amp Regulation Stations

Entrained liquids removed by the

Cyclotube

Liquids collect in the sump

Outlet

C Y C L O T U B E reg S E P A R A T O R

S E R I E S 95V-CT P r i n c i p l e o f O p e r a t i o n

The principle of operation is similar to that described for the 95SV Cyclotube scrubber except there is no first stage pre-separation of bulk contaminants and slugs prior to entering the Cyclotube separators The gas and contaminant directly enter the scrubbers Cyclotube separators which combine centrifugal pressure vacuum and flow vector forces to effect highly efficient separation while velocity scouring inherent in Cyclotube dynamics precludes fouling The removed contaminant is collected in a sump compartment located below the Cyclotube contaminant ejection ports Low differential pressure Cyclotubes are available for pressure sensitive applications This Separator should be used for medium liquid and solids loadings

Entrained liquids removed by the Vane

Liquids load from the bottom of the Vane

Liquids collect in the sump

Inlet

V A N E S E P A R A T O R

S E R I E S 95V-Inline Outlet

P r i n c i p l e o f O p e r a t i o n The principle of operation is similar to that described for the 95SV vane scrubber except there is no first stage pre-separation of bulk contaminants and slugs prior to entering the vane separator The gas and entrained contaminant directly enter the vane which utilizes inertial impaction to separate contaminants from the gas stream The removed contaminant then gravity drains into the sump This Separator should be used for light liquid loading with minimal solid contaminant loading

Information Required for Sizing Related configurationsproducts offered

bull Operating Pressure bull Horizontal Configuration bull Operating Temperature bull Alt-Line Configuration bull Gas Specific Gravity bull 3-Phase Separators bull Gas Flow Rate at above Conditions bull Multi-Cyclone Separators bull Contaminant bull Wire Mesh Separators bull Contaminant Flow Rate bull Removable Vane Packs bull Design Pressure bull Mist Eliminators also Sold Separately bull Corrosion Allowance

All PECOFacet Vane Mist Eliminators are built in accordance with ASME code for unfired pressure vessels national board stamp and local state and province require-ments as specified

Standard PECOFacet Vane Mist Eliminators are of welded carbon steel bodies with either carbon steel or stainless steel vane elements

PECOFacet is a world leader in the design and manufacture of quality Filtration Equipment specializing in the Oil and Gas Industry Founded in 1936 many of the technologies used in the Industry today were originally developed by PECOFacet Our continued dedication to research and development of new leading edge technologies has kept PECOFacet at the forefront of Engineered Filtration Solutions for use by our clients worldwide Our vast experience and knowledge of Oil amp Gas related applications allow us to offer not only Filtration Solutions but also Process Solutions

Consult factory for custom units including horizontal configurations and 3-phase separators

Your local

distributor

Corporate Headquarters

PO Box 640

Mineral Wells Texas 76068

Phone 8008777326

9403252575

Fax 9403254622

e-mail elementspecofacetcom

web site wwwpecofacetcom

Locations

Almere The Netherlands

Calgary Canada

Cedex France

Bergamo Italy

Beijing China

Bucharest Romania

Houston Texas

Kempen Germany

Kuala Lumpur Malaysia

La Coruna Spain

Manama Bahrain

Mid Glamorgan UK

Queretaro Mexico

Stillwell Oklahoma

Thetford UK

Torino Italy

Tulsa Oklahoma

Please refer to wwwpecofacetcom for most current literature edition

FS-95-SL-01 (LHA 1108) Printed in USA

Information Required for Sizing Related configurationsproducts offered

bull Operating Pressure bull Horizontal Configuration bull Operating Temperature bull Alt-Line Configuration bull Gas Specific Gravity bull 3-Phase Separators bull Gas Flow Rate at above Conditions bull Multi-Cyclone Separators bull Contaminant bull Wire Mesh Separators bull Contaminant Flow Rate bull Removable Vane Packs bull Design Pressure bull Mist Eliminators also Sold Separately bull Corrosion Allowance

All PECOFacet Vane Mist Eliminators are built in accordance with ASME code for unfired pressure vessels national board stamp and local state and province require-ments as specified

Standard PECOFacet Vane Mist Eliminators are of welded carbon steel bodies with either carbon steel or stainless steel vane elements

PECOFacet is a world leader in the design and manufacture of quality Filtration Equipment specializing in the Oil and Gas Industry Founded in 1936 many of the technologies used in the Industry today were originally developed by PECOFacet Our continued dedication to research and development of new leading edge technologies has kept PECOFacet at the forefront of Engineered Filtration Solutions for use by our clients worldwide Our vast experience and knowledge of Oil amp Gas related applications allow us to offer not only Filtration Solutions but also Process Solutions

Consult factory for custom units including horizontal configurations and 3-phase separators

Your local

distributor

Corporate Headquarters

PO Box 640

Mineral Wells Texas 76068

Phone 8008777326

9403252575

Fax 9403254622

e-mail elementspecofacetcom

web site wwwpecofacetcom

Locations

Almere The Netherlands

Calgary Canada

Cedex France

Bergamo Italy

Beijing China

Bucharest Romania

Houston Texas

Kempen Germany

Kuala Lumpur Malaysia

La Coruna Spain

Manama Bahrain

Mid Glamorgan UK

Queretaro Mexico

Stillwell Oklahoma

Thetford UK

Torino Italy

Tulsa Oklahoma

Please refer to wwwpecofacetcom for most current literature edition

FS-95-SL-01 (LHA 1108) Printed in USA