Amperometric nanobiosensor for quantitative determination of ...
ECL Data Sheet Open amperometric cells
Transcript of ECL Data Sheet Open amperometric cells
Data Sheet
Specifications subject to change without notice.EN R1-05-15ISO 9001:2008
ISO 14001:2004OHSAS 18001:2007
Via Donatori di sangue, 1 - 02100 Rieti - ItalyTel. +39 0746 2284 1 - Fax +39 0746 2284 2 - http://www.emec.it
ECL Open amperometric cells
CHLORINE in water can be present in different combination:
FREE CHLORINE ACTIVE: HOCl (hypochlorous acid)
COMBINED CHLORINE: Monochloramine, dichloramine, trichloramine (DPD4-DPD1 analysis system)
FREE ORGANIC CHLORINE: Free chlorine with isocyanide acid (DPD1 analysis system)
FREE INORGANIC CHLORINE: Free chlorine. (DPD1 analysis system)
TOTAL CHLORINE: Free chlorine and combined chlorine. (DPD4 analysis system)
• Chlorine probes (hypochlorous acid)
• Stable and reliable measurement even with low chlorine concentrations values
• Acrylic body• Continuous sampling measurement• Proximity flow sensor controlled (ECL6; ECL6/E; ECL7; ECL12; ECL12/E)
MODELS
• ECL20 FOR FREE CHLORINE (ORGANIC AND INORGANIC) FOR FRESH WATER• ECL21 FOR FREE CHLORINE (ORGANIC AND INORGANIC) FOR SALT WATER• ECL6 FOR FREE CHLORINE (ORGANIC AND INORGANIC)• ECL7 FOR FREE CHLORINE (ORGANIC AND INORGANIC)• ECL6/E FOR FREE CHLORINE (ORGANIC AND INORGANIC)• ECL12 FOR FREE CHLORINE (ORGANIC AND INORGANIC) FOR SALT WATER• ECL12/E FOR FREE CHLORINE (ORGANIC AND INORGANIC) FOR SALT WATER
ECL Series is designed for measuring free chlorine (both organic and inorganic).Open amperometric cells comprise an Off-line probe holders, a sensing electrode and a flow electrode.Probe holders can contain up to three probes (temperature, pH and ORP).
The flow of water within this cell must remain constant and within 40 l/h. A pressure stabilizer is available for areas subject to sudden pressure changes.
It is recommended to instal a filter before the probe holder.ECL6ECL7ECL12
ECL20ECL21
Data Sheet
Specifications subject to change without notice.EN R1-05-15ISO 9001:2008
ISO 14001:2004OHSAS 18001:2007
Via Donatori di sangue, 1 - 02100 Rieti - ItalyTel. +39 0746 2284 1 - Fax +39 0746 2284 2 - http://www.emec.it
ECL Open amperometric cells
ECL6ECL6/E ECL6 ECL6/E
Parameter FREE CHLORINE (ORGANIC AND INORGANIC) / BROMINE
Measuring range 0-10 mg/l (0-10 ppm) resolution: ± 0.05
Connection 2 wires (+red; -black)
Measuring system amperometric - 2 electrodes (platinum/copper; on request gold/copper)
Ph working range 6-8 pH
Run-in-timeFirst polarization: 2 h aboutNext polarizations: 50 min. about
Response time T90: 2 min. about
Zero point adjustment
See Operating manual: “Probe alignment”
Slope calibration See Operating manual: “Probe alignment”- DPD1 method
Alcalinity 100 ppm
Working temperature
5-40° C (41-104°F)
Pressure 0.4 - 5 bar (5.8 - 72.5 PSI)
Cable (standard) 2 m (6.6 ft); 1 m if assembled on panel
Working flow 40 l/h
Suitable as probe holder for
pH, ORP and temperature temperature
Fittings for connection to the sample pipeline
6x8
MaterialElectrode: platinum/copperMeasurement cell: metacrylate (PMMA)
Mounting On flat vertical surface (panel, support, etc.).
Storage Frost and dry protected (5-40° C)
MaintenanceRegular control of the signalSHORTEN THE MAINTENANCE INTERVALS APPROPRIATELY DEPENDING ON WATER QUALITY.
Data Sheet
Specifications subject to change without notice.EN R1-05-15ISO 9001:2008
ISO 14001:2004OHSAS 18001:2007
Via Donatori di sangue, 1 - 02100 Rieti - ItalyTel. +39 0746 2284 1 - Fax +39 0746 2284 2 - http://www.emec.it
ECL Open amperometric cells
ECL7ECL7
Parameter FREE CHLORINE (ORGANIC AND INORGANIC)
Measuring range 0-10 mg/l (0-10 ppm) resolution: ± 0.05
Connection 2 wires (+red; -black)
Measuring system amperometric - 2 electrodes (platinum/copper; on request gold/copper)
Ph working range 6-8 pH
Run-in-timeFirst polarization: 2 h aboutNext polarizations: 50 min. about
Response time T90: 2 min. about
Zero point adjustment
See Operating manual: “Probe alignment”
Slope calibration See Operating manual: “Probe alignment”- DPD1 method
Alcalinity 100 ppm
Working temperature
5-40° C (41-104°F)
Pressure 0.4 - 5 bar (5.8 - 72.5 PSI)
Cable (standard) 2 m (6.6 ft); 1 m if assembled on panel
Working flow 40 l/h
Suitable as probe holder for
pH, Redox (PG13,5) e temperature
Fittings for connection to the sample pipeline
6x8
MaterialElectrode: platinum/copperMeasurement cell: metacrylate (PMMA)
Mounting On flat vertical surface (panel, support, etc.).
Storage Frost and dry protected (5-40° C)
MaintenanceRegular control of the signalSHORTEN THE MAINTENANCE INTERVALS APPROPRIATELY DEPENDING ON WATER QUALITY.
Data Sheet
Specifications subject to change without notice.EN R1-05-15ISO 9001:2008
ISO 14001:2004OHSAS 18001:2007
Via Donatori di sangue, 1 - 02100 Rieti - ItalyTel. +39 0746 2284 1 - Fax +39 0746 2284 2 - http://www.emec.it
ECL Open amperometric cells
ECL12ECL12/E ECL12 ECL12/E
Parameter FREE CHLORINE (ORGANIC AND INORGANIC) FOR SALT WATER
Measuring range 0-10 mg/l (0-10 ppm) resolution: ± 0.05
Connection 2 wires (+red; -black)
Measuring system amperometric - 2 electrodes (platinum/silver)
Ph working range 6-8 pH
Run-in-timeFirst polarization: 2 h aboutNext polarizations: 50 min. about
Response time T90: 2 min. about
Zero point adjustment
See Operating manual: “Probe alignment”
Slope calibration See Operating manual: “Probe alignment”- DPD1 method
Alcalinity 100 ppm
Working temperature
5-40° C (41-104°F)
Pressure 0.4 - 5 bar (5.8 - 72.5 PSI)
Cable (standard) 2 m (6.6 ft); 1 m if assembled on panel
Working flow 40 l/h
Suitable as probe holder for
pH, ORP and temperature temperature
Fittings for connection to the sample pipeline
6x8
MaterialElectrode: platinum/silverMeasurement cell: metacrylate (PMMA)
Mounting On flat vertical surface (panel, support, etc.).
Storage Frost and dry protected (5-40° C)
MaintenanceRegular control of the signalSHORTEN THE MAINTENANCE INTERVALS APPROPRIATELY DEPENDING ON WATER QUALITY.
Data Sheet
Specifications subject to change without notice.EN R1-05-15ISO 9001:2008
ISO 14001:2004OHSAS 18001:2007
Via Donatori di sangue, 1 - 02100 Rieti - ItalyTel. +39 0746 2284 1 - Fax +39 0746 2284 2 - http://www.emec.it
ECL Open amperometric cells
ECL20ECL20
Parameter FREE CHLORINE (ORGANIC AND INORGANIC) FOR FRESH WATER
Measuring range 0-10 mg/l (0-10 ppm) resolution: ± 0.05
Connection 2 wires (+red; -black)
Measuring system amperometric - 2 electrodes
Ph working range 6-8 pH
Run-in-timeFirst polarization: 2 h aboutNext polarizations: 50 min. about
Response time T90: 2 min. about
Zero point adjustment
See Operating manual: “Probe alignment”
Slope calibration See Operating manual: “Probe alignment”- DPD1 method
Alcalinity 100 ppm
Working temperature
5-40° C (41-104°F)
Pressure 0.4 - 5 bar (5.8 - 72.5 PSI)
Cable (standard) 2 m (6.6 ft); 1 m if assembled on panel
Working flow 40 l/h
Fittings for connection to the sample pipeline
6x8
MaterialElectrode: platinum/copperMeasurement cell: metacrylate (PMMA)
Mounting On flat vertical surface (panel, support, etc.).
Storage Frost and dry protected (5-40° C)
MaintenanceRegular control of the signalSHORTEN THE MAINTENANCE INTERVALS APPROPRIATELY DEPENDING ON WATER QUALITY.
Data Sheet
Specifications subject to change without notice.EN R1-05-15ISO 9001:2008
ISO 14001:2004OHSAS 18001:2007
Via Donatori di sangue, 1 - 02100 Rieti - ItalyTel. +39 0746 2284 1 - Fax +39 0746 2284 2 - http://www.emec.it
ECL Open amperometric cells
ECL21ECL21
Parameter FREE CHLORINE (ORGANIC AND INORGANIC) FOR SALT WATER
Measuring range 0-10 mg/l (0-10 ppm) resolution: ± 0.05
Connection 2 wires (+red; -black)
Measuring system amperometric - 2 electrodes
Ph working range 6-8 pH
Run-in-timeFirst polarization: 2 h aboutNext polarizations: 50 min. about
Response time T90: 2 min. about
Zero point adjustment
See Operating manual: “Probe alignment”
Slope calibration See Operating manual: “Probe alignment”- DPD1 method
Alcalinity 100 ppm
Working temperature
5-40° C (41-104°F)
Pressure 0.4 - 5 bar (5.8 - 72.5 PSI)
Cable (standard) 2 m (6.6 ft); 1 m if assembled on panel
Working flow 40 l/h
Fittings for connection to the sample pipeline
6x8
MaterialElectrode: platinum/silver Measurement cell: metacrylate (PMMA)
Mounting On flat vertical surface (panel, support, etc.).
Storage Frost and dry protected (5-40° C)
MaintenanceRegular control of the signalSHORTEN THE MAINTENANCE INTERVALS APPROPRIATELY DEPENDING ON WATER QUALITY.
Data Sheet
Specifications subject to change without notice.EN R1-05-15ISO 9001:2008
ISO 14001:2004OHSAS 18001:2007
Via Donatori di sangue, 1 - 02100 Rieti - ItalyTel. +39 0746 2284 1 - Fax +39 0746 2284 2 - http://www.emec.it
ECL Open amperometric cells
1
1
2
2
3
3
4
4
5
5
6
6
A A
B B
C C
D D
Progettato da: Controllato da: Data:
Edizione Foglio1 / 1
ECL12E CELLA AMPEROMETRICAECL12E
Massimo_F Massimo_F 22/07/2015
00
Toll. Gen.±0.05
Peso Lordo: Peso Netto:
Materiale:
9.00
81.00
177.
30
60.0
0
171.70
9.00
100.
00
DIMENSIONS1
1
2
2
3
3
4
4
5
5
6
6
A A
B B
C C
D D
Progettato da: Controllato da: Data:
Edizione Foglio1 / 1
ECL12 CELLA AMPEROMETRICAECL12
Massimo_F Massimo_F 22/07/2015
00
Toll. Gen.±0.05
Peso Lordo:° Peso Netto:
Materiale:
60.0
0
201.70
223.
20
9.00
106.00
9.00
100.
00
ECL12
ECL12/E
Data Sheet
Specifications subject to change without notice.EN R1-05-15ISO 9001:2008
ISO 14001:2004OHSAS 18001:2007
Via Donatori di sangue, 1 - 02100 Rieti - ItalyTel. +39 0746 2284 1 - Fax +39 0746 2284 2 - http://www.emec.it
ECL Open amperometric cells
1
1
2
2
3
3
4
4
5
5
6
6
A A
B B
C C
D D
Progettato da: Controllato da: Data:
Edizione Foglio1 / 1
ECL6E CELLA AMPEROMETRICAECL6E
Massimo_F Massimo_F 21/07/2015
00
Toll. Gen.±0.05
Peso Lordo: Peso Netto:
Materiale:
9.00
81.00
177.
30
60.0
0
171.70
9.00
100.
00
1
1
2
2
3
3
4
4
5
5
6
6
A A
B B
C C
D D
Progettato da: Controllato da: Data:
Edizione Foglio1 / 1
ECL6 CELLA AMPEROMETRICAECL6
Massimo_F Massimo_F 21/07/2015
00
Toll. Gen.±0.05
Peso Lordo:° Peso Netto:
Materiale:
60.0
0
201.70
223.
20
9.00
106.00
9.00
100.
00
DIMENSIONS
ECL6 / ECL7
ECL6/E
Data Sheet
Specifications subject to change without notice.EN R1-05-15ISO 9001:2008
ISO 14001:2004OHSAS 18001:2007
Via Donatori di sangue, 1 - 02100 Rieti - ItalyTel. +39 0746 2284 1 - Fax +39 0746 2284 2 - http://www.emec.it
ECL Open amperometric cells
1
1
2
2
3
3
4
4
5
5
6
6
A A
B B
C C
D D
Progettato da: Controllato da: Data:
Edizione Foglio1 / 1
DIMENSIONALE ECL5NECL5N
Massimo_F Massimo_F 15/07/2015
00
Toll. Gen.±0.05
Peso Lordo: Peso Netto:
Materiale:
123.
90
110.00
55.0
010
.00
10.00
60.00
ECL21
ECL20
DIMENSIONI
11
22
33
44
55
66
AA
BB
CC
DD
Progettato da: Controllato da:
Data:
EdizioneFoglio1 / 1
DIMENSIO
NALE ECL20ECL20
Massim
o_FM
assimo_F
16/05/2016
00
Toll. Gen.
±0.05 Peso Lordo:
Peso Netto:
Materiale:
123.90
55.00
10.00
60.00
10.00
105.00