超硬ノンステップボーラーシリーズ...01...

穴加工用超硬工具 Carbide Boring Tool

WHNSB-TH/WNSB-TH超硬ノンステップボーラーシリーズCarbide Non Step Borer series

2020-10（K）2010-4:FP

安全上のご注意 Attentions on Safety

2. 取付け時のご注意

4. 再研削時のご注意

1. 取扱上のご注意

3. 使用上のご注意

フリーダイヤル技術相談5. 工具に関して、安全上の問題点・不明の点・その他相談がありましたら　　　　　　　　　　　へ　ご相談ください。

2. Cautions regarding mounting(1) Before use, check the outside appearance of the tool for scratches, cracks, etc. and that it is firmly

mounted in the collet chuck, etc.(2) If abnormal chattering, etc. occurs during use, stop the machine immediately and remove the cause

of the chattering.

4. Cautions regarding regrinding(1) If regrinding is not performed at the proper time, there is a risk of the tool breaking. Replace the tool

with one in good condition, or perform regrinding.(2) Grinding dust will be created when regrinding a tool. When regrinding, be sure to attach a safety

cover over the work area and wear safety clothes such as safety goggles, etc.(3) This product contains the specified chemical substance cobalt and its inorganic compounds. When　 performing regrinding or similar processing, be sure to handle the processing in accordance with　 thelocal laws and regulations regarding prevention of hazards due to specified chemical substances.

1. Cautions regarding handling(1) When removing the tool from its case (packaging), be careful that the tool does not pop out or is

dropped. Be particularly careful regarding contact with the tool flutes. (2) When handling tools with sharp cutting flutes, be careful not to touch the cutting flutes directly with your bare hands.

3. Cautions during use(1) Before use, confirm the dimensions and direction of rotation of the tool and milling work material.(2) The numerical values in the standard cutting conditions table should be used as criteria when starting

new work. The cutting conditions should be adjusted as appropriate when the cutting depth is large, the rigidity of the machine being used is low, or according to the conditions of the work material.

(3) Cutting tools are made of a hard material. During use, they may break and fly off. In addition, cuttingchips may also fly off. Since there is a danger of injury to workers, fire, or eye damage from such flying pieces, a safety cover should be attached when work is performed and safety equipment suchas safety goggles should be worn to create a safe environment for work.

(4) There is a risk of fire or inflammation due to sparks, heat due to breakage, and cutting chips. Do notuse where there is a risk of fire or explosion. Please caution of fire while using oil base coolant, fire prevention is necessary.

(5) Do not use the tool for any purpose other than that for which it is intended.

（１）工具をケース（梱包）から取り出す際は、工具の飛び出し、落下にご注意ください。特に工具刃部との接　触には十分ご注意をお願いします。

（２）鋭利な切れ刃を有する工具を取扱う際は、切れ刃を素手で直接触れないように注意してください。

（１）ご使用前に、工具の傷・割れ等の外観確認を行っていただき、コレットチャック等への取付けは確実に行ってください。　

（２）ご使用中に、異常な振動等が発生した場合は、直ちに機械を停止させて、その振動の原因を取り除い　てください。

（１）切削工具あるいは被削材の寸法・回転の方向は、あらかじめ確認しておいてください。（２）標準切削条件表の数値は、新しい作業の立上げの目安としてご利用ください。切込みが大きい場合、

使用機械の剛性が小さい場合あるいは被加工物の性状に応じて切削条件を適正に調整してご使用ください。

（３）切削工具材料は硬質の材料です。ご使用中に破損して飛散する場合があります。また、切りくずが飛散することがあります。これらの飛散物等は作業者を切傷させ、火傷あるいは目に入って負傷させる恐れがありますので、工具をご使用中はその周囲に安全カバーを取付け、保護めがね等の保護具を着用して安全な環境下での作業をお願いいたします。

（４）切削中に発生する火花や、破損による発熱や、切りくずによる引火・火災の危険があります。引火や爆発の危険のあるところでは使用しないでください。不水溶性切削液をご使用される場合は防火対策を必ず行なってください。

（５）工具を本来の目的以外にはご使用にならないでください。

（１）再研削時期が不適当であると工具が破損する恐れがあります。適正な工具と交換するか、再研削を行ってください。

（２）工具を再研削しますと粉塵が発生します。再研削時にはその周囲に安全カバーを取付け、保護めがね等の保護具を着用してください。

（3）本製品には特定化学物質に指定されたコバルト及びその無機化合物が含まれています。再研削等の　　加工を加える場合は特定化学物質障害予防規則(特化則)に従った取扱いをしてください。

Printed in JAPANベジタブルインクで印刷しています。Printed using vegetable oil ink.

掲載価格は消費税抜きの単価を表示しております。予告なく、改良・改善のために仕様変更することがあります。Specifications for the products listed in this catalog are subject to change without notice due to replacement or modification.

New Produc t News No.1005-8 2020-10

ホームページ

工具選定データベース【TOOL SEARCH】

フリーダイヤル技術相談http://www.moldino.com

本社〒１３０-００２６東京都墨田区両国４-３１-11（ヒューリック両国ビル８階）03-6890-5101

+81-3-6890-5103FAX 03-6890-5134FAX +81-3-6890-5128International Sales Dept .:

営業企画部 ☎03-6890-5102 FAX03-6890-5134 海外営業部 ☎03-6890-5103 FAX03-6890-5128

東京営業所東北営業所新潟営業所東関東営業所長野営業所北関東営業所神奈川営業所

☎☎☎☎☎☎☎

03-6890-5110022-208-51000258-87-12240294-88-94300268-21-37000276-59-6001046-400-9429

FAX03-6890-5133FAX022-208-5102FAX0258-87-1158FAX0294-88-9432FAX0268-21-3711FAX0276-59-6005FAX046-400-9435

MOLDINO Tool Engineering, Ltd.

図、表等のデータは試験結果の一例であり、保証値ではありません。「　　　　　　　」は株式会社MOLDINOの登録商標です。The diagrams and table data are examples of test results, and are not guaranteed values.“ ” is a registered trademark of MOLDINO Tool Engineering, Ltd.

ヨーロッパ／MOLDINO Tool Engineering Europe GmbH Itterpark 12, 40724 Hilden, Germany. TEL : +49-(0)2103-24820, FAX : +49-(0)2103-248230中　　国／MOLDINO Tool Engineering, (Shanghai) Ltd. Room 2604-2605, Metro Plaza, 555 Loushanguan Road, Changning Disctrict, Shanghai, 200051, CHINA TEL:+86-(0)21-3366-3058, FAX:+86-(0)21-3366-3050アメリカ／MITSUBISHI MATERIALS U.S.A. CORPORATION 41700 Gardenbrook Road, Suite 120, Novi, MI 48375-1320 U.S.A. TEL : +1(248)308-2620, FAX :+1(248)308-2627メキシコ／MMC METAL DE MEXICO, S.A. DE C.V. Av. La Cañada No.16, Parque Industrial Bernardo Quintana, El Marques, Querétaro, CP 76246, México TEL : +52-442-1926800 　　ブラジル／MMC METAL DO BRASIL LTDA. Rua Cincinato Braga, 340 13° andar.Bela Vista – CEP 01333-010 São Paulo – SP ., Brasil TEL : +55(11)3506-5600 FAX : +55(11)3506-5677 　　タ　　イ／MMC Hardmetal (Thailand) Co.,Ltd. MOLDINO Division 622 Emporium Tower, Floor 22/1-4, Sukhumvit Road, Klong Tan, Klong Toei, Bangkok 10110, Thailand TEL:+66-(0)2-661-8175 FAX:+66-(0)2-661-8176インド／Hitachi Metals (India) Pvt. Ltd. Plot No 94 & 95,Sector 8, IMT Manesar, Gurgaon -122050, Haryana, India TEL : +91-124-4812315, FAX :+91-124-2290015

☎☎☎☎☎☎

静岡営業所名古屋営業所大阪営業所中四営業所九州営業所北九州営業所

054-273-0360052-687-915006-7668-0190082-536-2001092-289-7010093-434-2640

FAX054-273-0361FAX052-687-9144FAX06-7668-0194FAX082-536-2003FAX092-289-7012FAX093-434-6846

THコーティングTH Coating

炭素鋼合金鋼

工具鋼プリハードン鋼焼入れ鋼45～55HRC

Carbon steelAlloy steep

Tool steel Pre-hardenedsteel

Hardened steel45̃55HRC

焼入れ鋼55～65HRCHardened steel

55̃65HRC

Applications 部品加工金型製作Parts processingMold making

加工用途

03~30WHNSB-THφ2～φ13 ［896 アイテムItems］

02・04WNSB-THφ1～φ13 ［ 222 アイテムItems］

●工具 Tool ：20WHNSB0600-TH　●切削条件：vc＝100m/min　f＝0.15mm/rev　H＝120mm Cutting conditions

●被削材：S50C　●水溶性切削液：内部給油 Work material Water-soluble coolant, internal oil supply

主軸負荷（トルク）の変化　Torque change on the main spindle

超硬ノンステップボーラー Carbide Non Step Borerマージンを4ヶ所に配置し、ガッチリガイド!!

良好な切りくず形状Well-shaped chips

NSB特殊溝形状で優れた切りくず排出!!NSB specially formed groove removal chips effectively.

Four guides with double margins

トラブルの起こりやすい通り穴の抜け際もWマージンでスムーズに加工！！Double margins enable stable boring even in the last stage of boring a through hole.

特殊溝形状で良好な切りくず排出特長Features 02 Specially shaped grooves removal chips effectively

高温でも安定性に優れるTHコート特長Features 01 TH coating improves stability during high-temperature boring.

Wマージンでがっちりガイド特長Features 03 Double margins enable firm guide.

NSB特殊溝形状で切りくず排出スピードが速い！超深穴（L/D=30）まで全て「ノンステップ！！」NSB特殊溝形状で切りくず排出スピードが速い！超深穴（L/D=30）まで全て「ノンステップ！！」

WHNSB-TH,WNSB-THの特長

01 耐酸化性、耐磨耗性にすぐれたＴＨコーティングを採用！耐酸化性、耐磨耗性にすぐれたＴＨコーティングを採用！

02 ＮＳＢ溝形状にてノンステップでスイスイ加工！ＮＳＢ溝形状にてノンステップでスイスイ加工！

03 高精度先端刃高精度先端刃

Completely non-step to ultra-deep (L/D=30) holes!!NSB specially shaped grooves enable quick chip discharge!

Features of WHNSB-TH and WNSB-TH

Oxidation and abrasion resistant TH coating.

High-accuracy cutting edge.

04 高精度シャンク、焼バメにも対応！高精度シャンク、焼バメにも対応！High accuracy shank capable of shrink fitting.

05 環境に優しいMQL（ミスト）加工も抜群の性能！環境に優しいMQL（ミスト）加工も抜群の性能！High-efficiency boring even for environment friendly MQL machining.

NSB specially shaped grooves enable non-step smooth boring

●印：標準在庫品です。●：Stocked Items.

□印：特定代理店在庫です。弊社営業へお問合せください。□：Stocked by specified distributor. Contact with our sales department.

直径Tooldia.

シャンク径Shank

dia.(mm) 02

2Dc※13Dc 4Dc※15Dc 8Dc 10Dc 15Dc 20Dc 30Dc 6.5 6.55 6.6 6.7 6.8 6.9 7 7.05 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 8 8.05 8.1 8.2 8.3 8.4 8.5 8.6 8.7 8.8 8.9 9 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9 10 10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 11.9 12 12.1 12.2 12.3 12.4 12.5 12.6 12.7 12.8 12.9 13

7.0 7.0 7.0 7.0 7.0 7.0 7.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0

10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0

●●●●●

●●●●●●●●●●

●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●

●●●●●

●●●●●●●●●●

●●●●●●●●●●□□●●●□□●●●□●●●●□□●●●□□●●●□□●●●□□□□●□□□□●

●●●●●

●●●●●●●●●●

□□●●●□□●●●□□●●●□□●●●□●●●●□●●●●□□●●●●□●●●□□□□●□□□□●

●●●●●

●●●●●●●●●●

□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□□□●□□□□●

●●●●●

●●●●●●●●●●

□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□□□●□□□□●

●●●●●

●●●●●●●●●●

□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□□□●□□□□●

25Dc●

●●●●●

●●●●●●●●●●

□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●

●●●●●

●●●●●●●●●●

□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□□□●□□□□●

●●●●●●●●●●●●●●●●●●●●●●●●●●●●●□□●●●□□●●●□●●●●□□●●●□□●●●□□●●●□□□□●□□□□●

□□●●●

□□●□●□□●●●

□□□●●●□●□●□□□●●□□●□●□●●□●●□●□●□□□●●●□●□●□●□□●●□□□●

直径Tooldia.

dia.(mm) 02

2Dc※13Dc 4Dc※15Dc 8Dc 10Dc 15Dc 20Dc 30Dc1.01.11.21.31.41.51.61.71.81.92.02.032.12.132.22.232.32.332.42.432.52.532.62.632.72.732.82.832.92.933.03.053.13.23.33.43.53.63.73.83.94.04.054.14.24.34.44.54.64.74.84.95.05.055.15.25.35.45.55.555.65.75.85.96.06.056.16.26.36.4

3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 7.0 7.0 7.0 7.0 7.0

●●●●●●●●●●●

●●●●●●●●●●

●●●●●

●●●●

●●●●●●●●●●

●●●●●

●●●●

●●●●●●●●●●

●●●●●

●●●●

●●●●●●●●●●

●●●●●

●●●●

●●●●●●●●●●

●●●●●

●●●●

●●●●●●●●●●

●●●●●

●●●●

●●●●●●●●●●

●●●●●

●●●●

●●●●●●●●●●

●●●●●

●●●●

●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●

□□□□□□□□□□

□□□□□□□□□●

●●□●●

□□●□●

□●□□

※1：オイルホールなしです。 ※1：Without oil hole

在庫一覧Stock i tem index

酸化

温度（

℃）

硬さ（HV) Hardness

2000 3000 4000

酸化温度と被膜の硬さ Oxidizing temperature and coating hardness

THTiAIN

900℃：60分 min 1000℃：60分 min

脆い酸化物。脱落し摩耗が進行。

Oxidation-resistant TH coating enables high-efficiency boring that causes high temperature.●耐酸化性に優れるTHコート採用で、切削温度の高くなる高能率領域に対応!!

Fragile oxide developspeeling and wear.

Fine, solid oxide with tight adhesionprevents wear.

緻密で強固な酸化物。密着性良好で摩耗の進行を防ぐ。

寸法・在庫拡大！！寸法・在庫拡大！！

全1118アイテムアイテム

Expanded Stocks & Items!!Total 1118 items

THコーティングTH Coating

炭素鋼合金鋼

工具鋼プリハードン鋼焼入れ鋼45～55HRC

Carbon steelAlloy steep

Tool steel Pre-hardenedsteel

Hardened steel45̃55HRC

焼入れ鋼55～65HRCHardened steel

55̃65HRC

Applications 部品加工金型製作Parts processingMold making

加工用途

03~30WHNSB-THφ2～φ13 ［896 アイテムItems］

02・04WNSB-THφ1～φ13 ［ 222 アイテムItems］

●工具 Tool ：20WHNSB0600-TH　●切削条件：vc＝100m/min　f＝0.15mm/rev　H＝120mm Cutting conditions

●被削材：S50C　●水溶性切削液：内部給油 Work material Water-soluble coolant, internal oil supply

主軸負荷（トルク）の変化　Torque change on the main spindle

超硬ノンステップボーラー Carbide Non Step Borerマージンを4ヶ所に配置し、ガッチリガイド!!

良好な切りくず形状Well-shaped chips

NSB特殊溝形状で優れた切りくず排出!!NSB specially formed groove removal chips effectively.

Four guides with double margins

トラブルの起こりやすい通り穴の抜け際もWマージンでスムーズに加工！！Double margins enable stable boring even in the last stage of boring a through hole.

特殊溝形状で良好な切りくず排出特長Features 02 Specially shaped grooves removal chips effectively

高温でも安定性に優れるTHコート特長Features 01 TH coating improves stability during high-temperature boring.

Wマージンでがっちりガイド特長Features 03 Double margins enable firm guide.

NSB特殊溝形状で切りくず排出スピードが速い！超深穴（L/D=30）まで全て「ノンステップ！！」NSB特殊溝形状で切りくず排出スピードが速い！超深穴（L/D=30）まで全て「ノンステップ！！」

WHNSB-TH,WNSB-THの特長

01 耐酸化性、耐磨耗性にすぐれたＴＨコーティングを採用！耐酸化性、耐磨耗性にすぐれたＴＨコーティングを採用！

02 ＮＳＢ溝形状にてノンステップでスイスイ加工！ＮＳＢ溝形状にてノンステップでスイスイ加工！

03 高精度先端刃高精度先端刃

Completely non-step to ultra-deep (L/D=30) holes!!NSB specially shaped grooves enable quick chip discharge!

Features of WHNSB-TH and WNSB-TH

Oxidation and abrasion resistant TH coating.

High-accuracy cutting edge.

04 高精度シャンク、焼バメにも対応！高精度シャンク、焼バメにも対応！High accuracy shank capable of shrink fitting.

05 環境に優しいMQL（ミスト）加工も抜群の性能！環境に優しいMQL（ミスト）加工も抜群の性能！High-efficiency boring even for environment friendly MQL machining.

NSB specially shaped grooves enable non-step smooth boring

直径Tooldia.

dia.(mm) 02

2Dc※13Dc 4Dc※15Dc 8Dc 10Dc 15Dc 20Dc 30Dc 6.5 6.55 6.6 6.7 6.8 6.9 7 7.05 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 8 8.05 8.1 8.2 8.3 8.4 8.5 8.6 8.7 8.8 8.9 9 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9 10 10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 11.9 12 12.1 12.2 12.3 12.4 12.5 12.6 12.7 12.8 12.9 13

7.0 7.0 7.0 7.0 7.0 7.0 7.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0

10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0

●●●●●

●●●●●●●●●●

●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●

●●●●●

●●●●●●●●●●

●●●●●●●●●●□□●●●□□●●●□●●●●□□●●●□□●●●□□●●●□□□□●□□□□●

●●●●●

●●●●●●●●●●

□□●●●□□●●●□□●●●□□●●●□●●●●□●●●●□□●●●●□●●●□□□□●□□□□●

●●●●●

●●●●●●●●●●

□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□□□●□□□□●

●●●●●

●●●●●●●●●●

□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□□□●□□□□●

●●●●●

●●●●●●●●●●

□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□□□●□□□□●

25Dc●

●●●●●

●●●●●●●●●●

□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●

●●●●●

●●●●●●●●●●

□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□□□●□□□□●

●●●●●●●●●●●●●●●●●●●●●●●●●●●●●□□●●●□□●●●□●●●●□□●●●□□●●●□□●●●□□□□●□□□□●

□□●●●

□□●□●□□●●●

□□□●●●□●□●□□□●●□□●□●□●●□●●□●□●□□□●●●□●□●□●□□●●□□□●

直径Tooldia.

dia.(mm) 02

2Dc※13Dc 4Dc※15Dc 8Dc 10Dc 15Dc 20Dc 30Dc1.01.11.21.31.41.51.61.71.81.92.02.032.12.132.22.232.32.332.42.432.52.532.62.632.72.732.82.832.92.933.03.053.13.23.33.43.53.63.73.83.94.04.054.14.24.34.44.54.64.74.84.95.05.055.15.25.35.45.55.555.65.75.85.96.06.056.16.26.36.4

3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 7.0 7.0 7.0 7.0 7.0

●●●●●●●●●●●

●●●●●●●●●●

●●●●●

●●●●

●●●●●●●●●●

●●●●●

●●●●

●●●●●●●●●●

●●●●●

●●●●

●●●●●●●●●●

●●●●●

●●●●

●●●●●●●●●●

●●●●●

●●●●

●●●●●●●●●●

●●●●●

●●●●

●●●●●●●●●●

●●●●●

●●●●

●●●●●●●●●●

●●●●●

●●●●

●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●

□□□□□□□□□□

□□□□□□□□□●

●●□●●

□□●□●

□●□□

※1：オイルホールなしです。 ※1：Without oil hole

在庫一覧Stock i tem index

酸化

温度（

℃）

硬さ（HV) Hardness

2000 3000 4000

酸化温度と被膜の硬さ Oxidizing temperature and coating hardness

THTiAIN

900℃：60分 min 1000℃：60分 min

脆い酸化物。脱落し摩耗が進行。

Oxidation-resistant TH coating enables high-efficiency boring that causes high temperature.●耐酸化性に優れるTHコート採用で、切削温度の高くなる高能率領域に対応!!

Fragile oxide developspeeling and wear.

Fine, solid oxide with tight adhesionprevents wear.

緻密で強固な酸化物。密着性良好で摩耗の進行を防ぐ。

寸法・在庫拡大！！寸法・在庫拡大！！

全1118アイテムアイテム

Expanded Stocks & Items!!Total 1118 items

在庫一覧

形状・寸法

切削条件

アプリケーション

03WHNSB -TH

平面二段・S-X形シンニングPlane, S-X thinning

全長：L

溝長：R

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

03WHNSB0200-TH03WHNSB0203-TH03WHNSB0210-TH03WHNSB0213-TH03WHNSB0220-TH03WHNSB0223-TH03WHNSB0230-TH03WHNSB0233-TH03WHNSB0240-TH03WHNSB0243-TH03WHNSB0250-TH03WHNSB0253-TH03WHNSB0260-TH03WHNSB0263-TH03WHNSB0270-TH03WHNSB0273-TH03WHNSB0280-TH03WHNSB0283-TH03WHNSB0290-TH03WHNSB0293-TH03WHNSB0300-TH03WHNSB0305-TH03WHNSB0310-TH03WHNSB0320-TH03WHNSB0330-TH03WHNSB0340-TH03WHNSB0350-TH03WHNSB0360-TH03WHNSB0370-TH03WHNSB0380-TH03WHNSB0390-TH03WHNSB0400-TH03WHNSB0405-TH03WHNSB0410-TH03WHNSB0420-TH03WHNSB0430-TH03WHNSB0440-TH03WHNSB0450-TH03WHNSB0460-TH03WHNSB0470-TH03WHNSB0480-TH03WHNSB0490-TH03WHNSB0500-TH03WHNSB0505-TH03WHNSB0510-TH03WHNSB0520-TH03WHNSB0530-TH03WHNSB0540-TH03WHNSB0550-TH03WHNSB0555-TH03WHNSB0560-TH03WHNSB0570-TH03WHNSB0580-TH03WHNSB0590-TH03WHNSB0600-TH03WHNSB0605-TH03WHNSB0610-TH03WHNSB0620-TH03WHNSB0630-TH03WHNSB0640-TH03WHNSB0650-TH03WHNSB0655-TH03WHNSB0660-TH03WHNSB0670-TH03WHNSB0680-TH

2.02.032.12.132.22.232.32.332.42.432.52.532.62.632.72.732.82.832.92.933.03.053.13.23.33.43.53.63.73.83.94.04.054.14.24.34.44.54.64.74.84.95.05.055.15.25.35.45.55.555.65.75.85.96.06.056.16.26.36.46.56.556.66.76.8

1616171717171919191919191919191919191919192323232323232323232323292929292929292929292929292929292929292929292934343434343434343434

6969696969696969696969696969696969696969697373737373737373737373828282828282828282828282828282828282828282828289898989898989898989

3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0

11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,940 11,940 11,940 11,940 11,940 11,940 12,140 12,140 12,140 12,140 12,140 12,450 12,450 12,450 12,450 12,450 12,450 12,550 12,550 12,550 12,550 12,550 13,260 13,260 13,260 13,260 13,260 13,260 13,570 13,570 13,570 13,570 13,570 13,570 14,490 14,490 14,490 14,490 14,490 14,490 14,790 14,790 14,790 14,790

●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●

在庫Stock

商品コードItem Code

希望小売価格（円）Suggested

retail price(￥)

With oil holeオイルホールあり

全長：L

溝長：R

05WHNSB -TH

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 8.0 8.1 8.2 8.3 8.4

2024242424242929292929373737373737373737374747474747474747474747474747474747474747555555555555555555556363636363636363636371717171

667474747474797979797987878787878787878787

100100100100100100100100100100100100100100100100100100100100110110110110110110110110110110119119119119119119119119119119128128128128

3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 9.0 9.0 9.0 9.0

13,260 13,260 13,260 13,260 13,260 13,260 13,260 13,260 13,260 13,260 13,260 13,670 13,670 13,670 13,670 13,670 13,770 13,770 13,770 13,770 13,770 14,180 14,180 14,180 14,180 14,180 14,490 14,490 14,490 14,490 14,490 15,300 15,300 15,300 15,300 15,300 15,510 15,510 15,510 15,510 15,510 16,530 16,530 16,530 16,530 16,530 16,940 16,940 16,940 16,940 16,940 18,260 18,260 18,260 18,260 18,260 18,770 18,770 18,770 18,770 18,770 20,000 20,000 20,000 20,000

●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●

在庫Stock

retail price(￥)

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

05WHNSB0850-TH05WHNSB0860-TH05WHNSB0870-TH05WHNSB0880-TH05WHNSB0890-TH05WHNSB0900-TH05WHNSB0910-TH05WHNSB0920-TH05WHNSB0930-TH05WHNSB0940-TH05WHNSB0950-TH05WHNSB0960-TH05WHNSB0970-TH05WHNSB0980-TH05WHNSB0990-TH05WHNSB1000-TH05WHNSB1010-TH05WHNSB1020-TH05WHNSB1030-TH05WHNSB1040-TH05WHNSB1050-TH05WHNSB1060-TH05WHNSB1070-TH05WHNSB1080-TH05WHNSB1090-TH05WHNSB1100-TH05WHNSB1110-TH05WHNSB1120-TH05WHNSB1130-TH05WHNSB1140-TH05WHNSB1150-TH05WHNSB1160-TH05WHNSB1170-TH05WHNSB1180-TH05WHNSB1190-TH05WHNSB1200-TH05WHNSB1210-TH05WHNSB1220-TH05WHNSB1230-TH05WHNSB1240-TH05WHNSB1250-TH05WHNSB1260-TH05WHNSB1270-TH05WHNSB1280-TH05WHNSB1290-TH05WHNSB1300-TH

8.5 8.6 8.7 8.8 8.9 9.0 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9

10.0 10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 11.9 12.0 12.1 12.2 12.3 12.4 12.5 12.6 12.7 12.8 12.9 13.0

717171717171797979797979797979798787878787878787878793939393939393939393

104104104104104104104104104104

128128128128128128137137137137137137137137137137150150150150150150150150150150156156156156156156156156156156169169169169169169169169169169

9.0 9.0 9.0 9.0 9.0 9.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0

●●●●●●□□●●●□□●●●□●●●●□□●●●□□●●●□□●●●□□□□●□□□□●

在庫Stock

retail price(￥)

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

03WHNSB0690-TH03WHNSB0700-TH03WHNSB0705-TH03WHNSB0710-TH03WHNSB0720-TH03WHNSB0730-TH03WHNSB0740-TH03WHNSB0750-TH03WHNSB0760-TH03WHNSB0770-TH03WHNSB0780-TH03WHNSB0790-TH03WHNSB0800-TH03WHNSB0805-TH03WHNSB0810-TH03WHNSB0820-TH03WHNSB0830-TH03WHNSB0840-TH03WHNSB0850-TH03WHNSB0860-TH03WHNSB0870-TH03WHNSB0880-TH03WHNSB0890-TH03WHNSB0900-TH03WHNSB0910-TH03WHNSB0920-TH03WHNSB0930-TH03WHNSB0940-TH03WHNSB0950-TH03WHNSB0960-TH03WHNSB0970-TH03WHNSB0980-TH03WHNSB0990-TH03WHNSB1000-TH03WHNSB1010-TH03WHNSB1020-TH03WHNSB1030-TH03WHNSB1040-TH03WHNSB1050-TH03WHNSB1060-TH03WHNSB1070-TH03WHNSB1080-TH03WHNSB1090-TH03WHNSB1100-TH03WHNSB1110-TH03WHNSB1120-TH03WHNSB1130-TH03WHNSB1140-TH03WHNSB1150-TH03WHNSB1160-TH03WHNSB1170-TH03WHNSB1180-TH03WHNSB1190-TH03WHNSB1200-TH03WHNSB1210-TH03WHNSB1220-TH03WHNSB1230-TH03WHNSB1240-TH03WHNSB1250-TH03WHNSB1260-TH03WHNSB1270-TH03WHNSB1280-TH03WHNSB1290-TH03WHNSB1300-TH

6.9 7.0 7.05 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 8.0 8.05 8.1 8.2 8.3 8.4 8.5 8.6 8.7 8.8 8.9 9.0 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9 10.0 10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 11.9 12.0 12.1 12.2 12.3 12.4 12.5 12.6 12.7 12.8 12.9 13.0

34343939393939393939393939444444444444444444444449494949494949494949545454545454545454545959595959595959595964646464646464646464

89899595959595959595959595

101101101101101101101101101101101107107107107107107107107107107117117117117117117117117117117123123123123123123123123123123129129129129129129129129129129

7.0 7.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0

10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0

●●●●●●●●●●●●●●●●●●●●●●●●□□●●●□□●●●□●●●●□□●●●□□●●●□□●●●□□□□●□□□□●

在庫Stock

retail price(￥)

Sheet of stocked items

ensionsCutting conditions

Applications

L/D=3 L/D=5

Carbide TH-Coated Normal Helix Integral No.Shank

φ2～φ3 ：0～－0.014φ3.05～φ6 ：0～－0.018φ6.05～φ10 ：0～－0.022φ10.1～φ13 ：0～－0.027

0～－0.01（㎜）

シャンク径公差 φ2～φ3 ：0～－0.014φ3.1～φ6 ：0～－0.018φ6.1～φ10 ：0～－0.022φ10.1～φ13 ：0～－0.027

0～－0.01（㎜）

シャンク径公差

ラインナップLine Up

14,790 14,790 16,120 16,120 16,120 16,120 16,120 16,120 16,430 16,430 16,430 16,430 16,430 17,550 17,550 17,550 17,550 17,550 17,550 17,850 17,850 17,850 17,850 17,850 －－

19,080 19,080 19,080 －－

19,490 19,490 19,490 －

20,710 20,710 20,710 20,710 －－

21,220 21,220 21,220 －－

22,340 22,340 22,340 －－

22,950 22,950 22,950 －－－－

25,200 －－－－

26,930

20,000 20,510 20,510 20,510 20,510 20,510 －－

21,830 21,830 21,830 －－

22,140 22,140 22,140 －

23,670 23,670 23,670 23,670 －－

24,080 24,080 24,080 －－

25,610 25,610 25,610 －－

26,220 26,220 26,220 －－－－

28,770 －－－－

30,710

在庫一覧

形状・寸法

切削条件

03WHNSB -TH

全長：L

溝長：R

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

2.02.032.12.132.22.232.32.332.42.432.52.532.62.632.72.732.82.832.92.933.03.053.13.23.33.43.53.63.73.83.94.04.054.14.24.34.44.54.64.74.84.95.05.055.15.25.35.45.55.555.65.75.85.96.06.056.16.26.36.46.56.556.66.76.8

1616171717171919191919191919191919191919192323232323232323232323292929292929292929292929292929292929292929292934343434343434343434

6969696969696969696969696969696969696969697373737373737373737373828282828282828282828282828282828282828282828289898989898989898989

3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0

11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,630 11,940 11,940 11,940 11,940 11,940 11,940 12,140 12,140 12,140 12,140 12,140 12,450 12,450 12,450 12,450 12,450 12,450 12,550 12,550 12,550 12,550 12,550 13,260 13,260 13,260 13,260 13,260 13,260 13,570 13,570 13,570 13,570 13,570 13,570 14,490 14,490 14,490 14,490 14,490 14,490 14,790 14,790 14,790 14,790

●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●

在庫Stock

retail price(￥)

全長：L

溝長：R

05WHNSB -TH

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 8.0 8.1 8.2 8.3 8.4

2024242424242929292929373737373737373737374747474747474747474747474747474747474747555555555555555555556363636363636363636371717171

667474747474797979797987878787878787878787

100100100100100100100100100100100100100100100100100100100100110110110110110110110110110110119119119119119119119119119119128128128128

3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 9.0 9.0 9.0 9.0

13,260 13,260 13,260 13,260 13,260 13,260 13,260 13,260 13,260 13,260 13,260 13,670 13,670 13,670 13,670 13,670 13,770 13,770 13,770 13,770 13,770 14,180 14,180 14,180 14,180 14,180 14,490 14,490 14,490 14,490 14,490 15,300 15,300 15,300 15,300 15,300 15,510 15,510 15,510 15,510 15,510 16,530 16,530 16,530 16,530 16,530 16,940 16,940 16,940 16,940 16,940 18,260 18,260 18,260 18,260 18,260 18,770 18,770 18,770 18,770 18,770 20,000 20,000 20,000 20,000

●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●

在庫Stock

retail price(￥)

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

8.5 8.6 8.7 8.8 8.9 9.0 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9

10.0 10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 11.9 12.0 12.1 12.2 12.3 12.4 12.5 12.6 12.7 12.8 12.9 13.0

717171717171797979797979797979798787878787878787878793939393939393939393

104104104104104104104104104104

128128128128128128137137137137137137137137137137150150150150150150150150150150156156156156156156156156156156169169169169169169169169169169

9.0 9.0 9.0 9.0 9.0 9.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0

●●●●●●□□●●●□□●●●□●●●●□□●●●□□●●●□□●●●□□□□●□□□□●

在庫Stock

retail price(￥)

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

6.9 7.0 7.05 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 8.0 8.05 8.1 8.2 8.3 8.4 8.5 8.6 8.7 8.8 8.9 9.0 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9 10.0 10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 11.9 12.0 12.1 12.2 12.3 12.4 12.5 12.6 12.7 12.8 12.9 13.0

34343939393939393939393939444444444444444444444449494949494949494949545454545454545454545959595959595959595964646464646464646464

89899595959595959595959595

101101101101101101101101101101101107107107107107107107107107107117117117117117117117117117117123123123123123123123123123123129129129129129129129129129129

7.0 7.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0

10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0

●●●●●●●●●●●●●●●●●●●●●●●●□□●●●□□●●●□●●●●□□●●●□□●●●□□●●●□□□□●□□□□●

在庫Stock

retail price(￥)

Applications

L/D=3 L/D=5

φ2～φ3 ：0～－0.014φ3.05～φ6 ：0～－0.018φ6.05～φ10 ：0～－0.022φ10.1～φ13 ：0～－0.027

0～－0.01（㎜）

シャンク径公差 φ2～φ3 ：0～－0.014φ3.1～φ6 ：0～－0.018φ6.1～φ10 ：0～－0.022φ10.1～φ13 ：0～－0.027

0～－0.01（㎜）

14,790 14,790 16,120 16,120 16,120 16,120 16,120 16,120 16,430 16,430 16,430 16,430 16,430 17,550 17,550 17,550 17,550 17,550 17,550 17,850 17,850 17,850 17,850 17,850 －－

19,080 19,080 19,080 －－

19,490 19,490 19,490 －

20,710 20,710 20,710 20,710 －－

21,220 21,220 21,220 －－

22,340 22,340 22,340 －－

22,950 22,950 22,950 －－－－

25,200 －－－－

26,930

20,000 20,510 20,510 20,510 20,510 20,510 －－

21,830 21,830 21,830 －－

22,140 22,140 22,140 －

23,670 23,670 23,670 23,670 －－

24,080 24,080 24,080 －－

25,610 25,610 25,610 －－

26,220 26,220 26,220 －－－－

28,770 －－－－

30,710

在庫一覧

形状・寸法

切削条件

08WHNSB -TH 10WHNSB -TH

溝長：R

全長：L

※1印：溝全体コーティングです Completely coated

全長：L

溝長：R

Applications

L/D=8 L/D=10寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 8.0 8.1 8.2 8.3 8.4

2525252828283333353535424242424246464646465555555555595959595962626262626767676767737373737377777777778484848484888888888894949494

757575757575808083838394949494949494949494

110110110110110110110110110110118118118118118118118118118118132132132132132132132132132132144144144144144144144144144144156156156156

3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 9.0 9.0 9.0 9.0

17,450 17,450 17,450 17,450 17,450 17,450 17,450 17,450 17,450 17,450 17,450 17,850 17,850 17,850 17,850 17,850 18,060 18,060 18,060 18,060 18,060 18,670 18,670 18,670 18,670 18,670 18,870 18,870 18,870 18,870 18,870 19,790 19,790 19,790 19,790 19,790 20,200 20,200 20,200 20,200 20,200 21,320 21,320 21,320 21,320 21,320 21,630 21,630 21,630 21,630 21,630 23,260 23,260 23,260 23,260 23,260 23,670 23,670 23,670 23,670 23,670 －－

25,500 25,500

●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●□□●●

在庫Stock

retail price(￥)

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

8.5 8.6 8.7 8.8 8.9 9.0 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9

10.0 10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 11.9 12.0 12.1 12.2 12.3 12.4 12.5 12.6 12.7 12.8 12.9 13.0

949999999999

105105105105105110110110110110116116116116116121121121121121127127127127127132132132132132138138138138138143143143143143

156156156156156156168168168168168168168168168168184184184184184184184184184184195195195195195195195195195195208208208208208208208208208208

9.0 9.0 9.0 9.0 9.0 9.0

10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0

●□□●●●□□●●●□□●●●□●●●●□●●●●□□●●●●□●●●□□□□●□□□□●

在庫Stock

retail price(￥)

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

※1 10WHNSB0200-TH※1 10WHNSB0210-TH※1 10WHNSB0220-TH※1 10WHNSB0230-TH※1 10WHNSB0240-TH※1 10WHNSB0250-TH※1 10WHNSB0260-TH※1 10WHNSB0270-TH※1 10WHNSB0280-TH※1 10WHNSB0290-TH※1 10WHNSB0300-TH※1 10WHNSB0310-TH※1 10WHNSB0320-TH※1 10WHNSB0330-TH※1 10WHNSB0340-TH※1 10WHNSB0350-TH※1 10WHNSB0360-TH※1 10WHNSB0370-TH※1 10WHNSB0380-TH※1 10WHNSB0390-TH※1 10WHNSB0400-TH※1 10WHNSB0410-TH※1 10WHNSB0420-TH※1 10WHNSB0430-TH※1 10WHNSB0440-TH※1 10WHNSB0450-TH※1 10WHNSB0460-TH※1 10WHNSB0470-TH※1 10WHNSB0480-TH※1 10WHNSB0490-TH※1 10WHNSB0500-TH※1 10WHNSB0510-TH※1 10WHNSB0520-TH※1 10WHNSB0530-TH※1 10WHNSB0540-TH※1 10WHNSB0550-TH※1 10WHNSB0560-TH※1 10WHNSB0570-TH※1 10WHNSB0580-TH※1 10WHNSB0590-TH※1 10WHNSB0600-TH※1 10WHNSB0610-TH※1 10WHNSB0620-TH※1 10WHNSB0630-TH※1 10WHNSB0640-TH※1 10WHNSB0650-TH※1 10WHNSB0660-TH※1 10WHNSB0670-TH※1 10WHNSB0680-TH※1 10WHNSB0690-TH※1 10WHNSB0700-TH※1 10WHNSB0710-TH※1 10WHNSB0720-TH※1 10WHNSB0730-TH※1 10WHNSB0740-TH※1 10WHNSB0750-TH※1 10WHNSB0760-TH※1 10WHNSB0770-TH※1 10WHNSB0780-TH※1 10WHNSB0790-TH※1 10WHNSB0800-TH※1 10WHNSB0810-TH※1 10WHNSB0820-TH※1 10WHNSB0830-TH※1 10WHNSB0840-TH

2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 8.0 8.1 8.2 8.3 8.4

3030303333333535393939464646464652525252525959595959666666666672727272727979797979858585858592929292929898989898

105105105105105111111111111

80808080808085858587879494949494

101101101101101110110110110110117117117117117123123123123123130130130130130138138138138138145145145145145153153153153153160160160160160166166166166

3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 9.0 9.0 9.0 9.0

●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●□□●●

在庫Stock

retail price(￥)

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

8.5 8.6 8.7 8.8 8.9 9.0 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9

10.0 10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 11.9 12.0 12.1 12.2 12.3 12.4 12.5 12.6 12.7 12.8 12.9 13.0

111118118118118118124124124124124131131131131131138138138138138144144144144144151151151151151157157157157157164164164164164170170170170170

166173173173173173179179179179179186186186186186193193193193193205205205205205212212212212212218218218218218225225225225225236236236236236

9.0 9.0 9.0 9.0 9.0 9.0

10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0

●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□□□●□□□□●

在庫Stock

retail price(￥)

※1 10WHNSB0850-TH10WHNSB0860-TH10WHNSB0870-TH10WHNSB0880-TH10WHNSB0890-TH10WHNSB0900-TH10WHNSB0910-TH10WHNSB0920-TH10WHNSB0930-TH10WHNSB0940-TH10WHNSB0950-TH10WHNSB0960-TH10WHNSB0970-TH10WHNSB0980-TH10WHNSB0990-TH10WHNSB1000-TH10WHNSB1010-TH10WHNSB1020-TH10WHNSB1030-TH10WHNSB1040-TH10WHNSB1050-TH10WHNSB1060-TH10WHNSB1070-TH10WHNSB1080-TH10WHNSB1090-TH10WHNSB1100-TH10WHNSB1110-TH10WHNSB1120-TH10WHNSB1130-TH10WHNSB1140-TH10WHNSB1150-TH10WHNSB1160-TH10WHNSB1170-TH10WHNSB1180-TH10WHNSB1190-TH10WHNSB1200-TH10WHNSB1210-TH10WHNSB1220-TH10WHNSB1230-TH10WHNSB1240-TH10WHNSB1250-TH10WHNSB1260-TH10WHNSB1270-TH10WHNSB1280-TH10WHNSB1290-TH10WHNSB1300-TH

3.0＜φDc＜6.0 6.0＜φDc＜10.0 10.0＜φDc≦13.0

上限Max

下限Min

－0.020

－0.036

－0.024

－0.045

－0.030

－0.053

10WHNSB

直径2.0～3.0、3.5、4.0、4.5、5.0、5.5、6.0、6.5、7.0、7.5、8.0、8.5、9.0、10.0、11.0、12.0、13.0はh8となります。上記以外のアイテムは下表の直径公差になります。h8 for diameters of 2.0 to 3.0, 3.5, 4.0, 4.5, 5.0, 5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0, 10.0, 11.0,12.0, and 13.0. For other items, the diameter tolerance will be as in the table below.

■10WHNSB直径公差表 Table of Tolerance on tool dia.

φ2～φ3 ：0～－0.014φ3.1～φ6 ：0～－0.018φ6.1～φ10 ：0～－0.022φ10.1～φ13 ：0～－0.027

0～－0.01（㎜）

シャンク径公差 Ds＝3 ：0～－0.006 3＜Ds≦6 ：0～－0.008 6＜Ds≦10 ：0～－0.00910＜Ds ：0～－0.011

下表を参照Refer to under table

（㎜）

直径公差

25,500 －－

26,120 26,120 26,120 －－

28,460 28,460 28,460 －－

29,070 29,070 29,070 －

32,240 32,240 32,240 32,240 －

32,850 32,850 32,850 32,850 －－

36,420 36,420 36,420 36,930 －

36,930 36,930 36,930 －－－－

42,840 －－－－

43,560

21,420 21,420 21,420 21,420 21,420 21,420 21,420 21,420 21,420 21,420 21,420 21,730 21,730 21,730 21,730 21,730 22,040 22,040 22,040 22,040 22,040 22,550 22,550 22,550 22,550 22,550 23,060 23,060 23,060 23,060 23,060 24,590 24,590 24,590 24,590 24,590 26,010 26,010 26,010 26,010 26,010 27,950 27,950 27,950 27,950 27,950 29,790 29,790 29,790 29,790 29,790 31,420 31,420 31,420 31,420 31,420 32,950 32,950 32,950 32,950 32,950 －－

34,790 34,790

34,790 －－

36,520 36,520 36,520 －－

37,850 37,850 37,850 －－

39,680 39,680 39,680 －－

44,070 44,070 44,070 －－

45,900 45,900 45,900 －－

48,860 48,860 48,860 －－

50,600 50,600 50,600 －－－－

55,390 －－－－

57,330

在庫一覧

形状・寸法

切削条件

08WHNSB -TH 10WHNSB -TH

溝長：R

全長：L

※1印：溝全体コーティングです Completely coated

全長：L

溝長：R

Applications

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 8.0 8.1 8.2 8.3 8.4

2525252828283333353535424242424246464646465555555555595959595962626262626767676767737373737377777777778484848484888888888894949494

757575757575808083838394949494949494949494

110110110110110110110110110110118118118118118118118118118118132132132132132132132132132132144144144144144144144144144144156156156156

3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 9.0 9.0 9.0 9.0

17,450 17,450 17,450 17,450 17,450 17,450 17,450 17,450 17,450 17,450 17,450 17,850 17,850 17,850 17,850 17,850 18,060 18,060 18,060 18,060 18,060 18,670 18,670 18,670 18,670 18,670 18,870 18,870 18,870 18,870 18,870 19,790 19,790 19,790 19,790 19,790 20,200 20,200 20,200 20,200 20,200 21,320 21,320 21,320 21,320 21,320 21,630 21,630 21,630 21,630 21,630 23,260 23,260 23,260 23,260 23,260 23,670 23,670 23,670 23,670 23,670 －－

25,500 25,500

●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●□□●●

在庫Stock

retail price(￥)

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

8.5 8.6 8.7 8.8 8.9 9.0 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9

10.0 10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 11.9 12.0 12.1 12.2 12.3 12.4 12.5 12.6 12.7 12.8 12.9 13.0

949999999999

105105105105105110110110110110116116116116116121121121121121127127127127127132132132132132138138138138138143143143143143

156156156156156156168168168168168168168168168168184184184184184184184184184184195195195195195195195195195195208208208208208208208208208208

9.0 9.0 9.0 9.0 9.0 9.0

10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0

●□□●●●□□●●●□□●●●□●●●●□●●●●□□●●●●□●●●□□□□●□□□□●

在庫Stock

retail price(￥)

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

※1 10WHNSB0200-TH※1 10WHNSB0210-TH※1 10WHNSB0220-TH※1 10WHNSB0230-TH※1 10WHNSB0240-TH※1 10WHNSB0250-TH※1 10WHNSB0260-TH※1 10WHNSB0270-TH※1 10WHNSB0280-TH※1 10WHNSB0290-TH※1 10WHNSB0300-TH※1 10WHNSB0310-TH※1 10WHNSB0320-TH※1 10WHNSB0330-TH※1 10WHNSB0340-TH※1 10WHNSB0350-TH※1 10WHNSB0360-TH※1 10WHNSB0370-TH※1 10WHNSB0380-TH※1 10WHNSB0390-TH※1 10WHNSB0400-TH※1 10WHNSB0410-TH※1 10WHNSB0420-TH※1 10WHNSB0430-TH※1 10WHNSB0440-TH※1 10WHNSB0450-TH※1 10WHNSB0460-TH※1 10WHNSB0470-TH※1 10WHNSB0480-TH※1 10WHNSB0490-TH※1 10WHNSB0500-TH※1 10WHNSB0510-TH※1 10WHNSB0520-TH※1 10WHNSB0530-TH※1 10WHNSB0540-TH※1 10WHNSB0550-TH※1 10WHNSB0560-TH※1 10WHNSB0570-TH※1 10WHNSB0580-TH※1 10WHNSB0590-TH※1 10WHNSB0600-TH※1 10WHNSB0610-TH※1 10WHNSB0620-TH※1 10WHNSB0630-TH※1 10WHNSB0640-TH※1 10WHNSB0650-TH※1 10WHNSB0660-TH※1 10WHNSB0670-TH※1 10WHNSB0680-TH※1 10WHNSB0690-TH※1 10WHNSB0700-TH※1 10WHNSB0710-TH※1 10WHNSB0720-TH※1 10WHNSB0730-TH※1 10WHNSB0740-TH※1 10WHNSB0750-TH※1 10WHNSB0760-TH※1 10WHNSB0770-TH※1 10WHNSB0780-TH※1 10WHNSB0790-TH※1 10WHNSB0800-TH※1 10WHNSB0810-TH※1 10WHNSB0820-TH※1 10WHNSB0830-TH※1 10WHNSB0840-TH

2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 8.0 8.1 8.2 8.3 8.4

3030303333333535393939464646464652525252525959595959666666666672727272727979797979858585858592929292929898989898

105105105105105111111111111

80808080808085858587879494949494

101101101101101110110110110110117117117117117123123123123123130130130130130138138138138138145145145145145153153153153153160160160160160166166166166

3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 9.0 9.0 9.0 9.0

●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●□□●●

在庫Stock

retail price(￥)

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

8.5 8.6 8.7 8.8 8.9 9.0 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9

10.0 10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 11.9 12.0 12.1 12.2 12.3 12.4 12.5 12.6 12.7 12.8 12.9 13.0

111118118118118118124124124124124131131131131131138138138138138144144144144144151151151151151157157157157157164164164164164170170170170170

166173173173173173179179179179179186186186186186193193193193193205205205205205212212212212212218218218218218225225225225225236236236236236

9.0 9.0 9.0 9.0 9.0 9.0

10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0

●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□□□●□□□□●

在庫Stock

retail price(￥)

※1 10WHNSB0850-TH10WHNSB0860-TH10WHNSB0870-TH10WHNSB0880-TH10WHNSB0890-TH10WHNSB0900-TH10WHNSB0910-TH10WHNSB0920-TH10WHNSB0930-TH10WHNSB0940-TH10WHNSB0950-TH10WHNSB0960-TH10WHNSB0970-TH10WHNSB0980-TH10WHNSB0990-TH10WHNSB1000-TH10WHNSB1010-TH10WHNSB1020-TH10WHNSB1030-TH10WHNSB1040-TH10WHNSB1050-TH10WHNSB1060-TH10WHNSB1070-TH10WHNSB1080-TH10WHNSB1090-TH10WHNSB1100-TH10WHNSB1110-TH10WHNSB1120-TH10WHNSB1130-TH10WHNSB1140-TH10WHNSB1150-TH10WHNSB1160-TH10WHNSB1170-TH10WHNSB1180-TH10WHNSB1190-TH10WHNSB1200-TH10WHNSB1210-TH10WHNSB1220-TH10WHNSB1230-TH10WHNSB1240-TH10WHNSB1250-TH10WHNSB1260-TH10WHNSB1270-TH10WHNSB1280-TH10WHNSB1290-TH10WHNSB1300-TH

3.0＜φDc＜6.0 6.0＜φDc＜10.0 10.0＜φDc≦13.0

上限Max

下限Min

－0.020

－0.036

－0.024

－0.045

－0.030

－0.053

10WHNSB

直径2.0～3.0、3.5、4.0、4.5、5.0、5.5、6.0、6.5、7.0、7.5、8.0、8.5、9.0、10.0、11.0、12.0、13.0はh8となります。上記以外のアイテムは下表の直径公差になります。h8 for diameters of 2.0 to 3.0, 3.5, 4.0, 4.5, 5.0, 5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0, 10.0, 11.0,12.0, and 13.0. For other items, the diameter tolerance will be as in the table below.

φ2～φ3 ：0～－0.014φ3.1～φ6 ：0～－0.018φ6.1～φ10 ：0～－0.022φ10.1～φ13 ：0～－0.027

0～－0.01（㎜）

シャンク径公差 Ds＝3 ：0～－0.006 3＜Ds≦6 ：0～－0.008 6＜Ds≦10 ：0～－0.00910＜Ds ：0～－0.011

（㎜）

直径公差

25,500 －－

26,120 26,120 26,120 －－

28,460 28,460 28,460 －－

29,070 29,070 29,070 －

32,240 32,240 32,240 32,240 －

32,850 32,850 32,850 32,850 －－

36,420 36,420 36,420 36,930 －

36,930 36,930 36,930 －－－－

42,840 －－－－

43,560

21,420 21,420 21,420 21,420 21,420 21,420 21,420 21,420 21,420 21,420 21,420 21,730 21,730 21,730 21,730 21,730 22,040 22,040 22,040 22,040 22,040 22,550 22,550 22,550 22,550 22,550 23,060 23,060 23,060 23,060 23,060 24,590 24,590 24,590 24,590 24,590 26,010 26,010 26,010 26,010 26,010 27,950 27,950 27,950 27,950 27,950 29,790 29,790 29,790 29,790 29,790 31,420 31,420 31,420 31,420 31,420 32,950 32,950 32,950 32,950 32,950 －－

34,790 34,790

34,790 －－

36,520 36,520 36,520 －－

37,850 37,850 37,850 －－

39,680 39,680 39,680 －－

44,070 44,070 44,070 －－

45,900 45,900 45,900 －－

48,860 48,860 48,860 －－

50,600 50,600 50,600 －－－－

55,390 －－－－

57,330

在庫一覧

形状・寸法

切削条件

15WHNSB -TH

溝長：R

全長：L

s 平面二段・S-X形シンニングPlane, S-X thinning

溝長：R

全長：L

20WHNSB -TH

Applications

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 8.0 8.1 8.2 8.3

40444450505054545454546363636363727272727281818181819191919191

100100100100100109109109109109118118118118118127127127127127136136136136136145145145145145154154154

838787939393

102102102102102111111111111111121121121121121132132132132132142142142142142151151151151151160160160160160171171171171171180180180180180191191191191191200200200200200209209209

3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 9.0 9.0 9.0

●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●□□●

在庫Stock

retail price(￥)

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

15WHNSB0840-TH15WHNSB0850-TH15WHNSB0860-TH15WHNSB0870-TH15WHNSB0880-TH15WHNSB0890-TH15WHNSB0900-TH15WHNSB0910-TH15WHNSB0920-TH15WHNSB0930-TH15WHNSB0940-TH15WHNSB0950-TH15WHNSB0960-TH15WHNSB0970-TH15WHNSB0980-TH15WHNSB0990-TH15WHNSB1000-TH15WHNSB1010-TH15WHNSB1020-TH15WHNSB1030-TH15WHNSB1040-TH15WHNSB1050-TH15WHNSB1060-TH15WHNSB1070-TH15WHNSB1080-TH15WHNSB1090-TH15WHNSB1100-TH15WHNSB1110-TH15WHNSB1120-TH15WHNSB1130-TH15WHNSB1140-TH15WHNSB1150-TH15WHNSB1160-TH15WHNSB1170-TH15WHNSB1180-TH15WHNSB1190-TH15WHNSB1200-TH15WHNSB1210-TH15WHNSB1220-TH15WHNSB1230-TH15WHNSB1240-TH15WHNSB1250-TH15WHNSB1260-TH15WHNSB1270-TH15WHNSB1280-TH15WHNSB1290-TH15WHNSB1300-TH

8.4 8.5 8.6 8.7 8.8 8.9 9.0 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9

10.0 10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 11.9 12.0 12.1 12.2 12.3 12.4 12.5 12.6 12.7 12.8 12.9 13.0

154154163163163163163172172172172172181181181181181190190190190190199199199199199208208208208208217217217217217226226226226226235235235235235

209209218218218218218227227227227227236236236236236245245245245245260260260260260269269269269269278278278278278287287287287287301301301301301

9.0 9.0 9.0 9.0 9.0 9.0 9.0

10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0

●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□□□●□□□□●

在庫Stock

retail price(￥)

3.0＜φDc＜6.0 6.0＜φDc＜10.0 10.0＜φDc≦13.0

上限Max

下限Min

－0.020

－0.036

－0.024

－0.045

－0.030

－0.053

15WHNSB

直径2.0～3.0、3.5、4.0、4.5、5.0、5.5、6.0、6.5、7.0、7.5、8.0、8.5、9.0、10.0、11.0、12.0、13.0はh8となります。上記以外のアイテムは下表の直径公差になります。h8 for diameters of 2.0 to 3.0, 3.5, 4.0, 4.5, 5.0, 5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0, 10.0, 11.0,12.0 and 13.0. For other items, the diameter tolerance will be as in the table below.

■15WHNSB直径公差表　Table of Tolerance on tool dia.

3.0＜φDc＜6.0 6.0＜φDc＜10.0 10.0＜φDc≦13.0

上限Max

下限Min

－0.020

－0.036

－0.024

－0.045

－0.030

－0.053

20WHNSB

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 8.0 8.1 8.2 8.3

505555626262676769696981818181819292929292

104104104104104116116116116116127127127127127139139139139139150150150150150162162162162162173173173173173185185185185185196196196

939898

105105105110110115115117129129129129129141141141141141155155155155155167167167167167178178178178178190190190190190203203203203203215215215215215228228228228228240240240240240251251251

3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 9.0 9.0 9.0

●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●□□●

在庫Stock

retail price(￥)

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

8.4 8.5 8.6 8.7 8.8 8.9 9.0 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9

10.0 10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 11.9 12.0 12.1 12.2 12.3 12.4 12.5 12.6 12.7 12.8 12.9 13.0

196196208208208208208219219219219219231231231231231243243243243243254254254254254266266266266266277277277277277289289289289289300300300300300

251251263263263263263274274274274274286286286286286298298298298298315315315315315327327327327327338338338338338350350350350350366366366366366

9.0 9.0 9.0 9.0 9.0 9.0 9.0

10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0

●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□□□●□□□□●

在庫Stock

retail price(￥)

26,930 26,930 26,930 26,930 26,930 26,930 26,930 26,930 26,930 26,930 26,930 27,340 27,340 27,340 27,340 27,340 27,650 27,650 27,650 27,650 27,650 28,260 28,260 28,260 28,260 28,260 28,870 28,870 28,870 28,870 28,870 30,810 30,810 30,810 30,810 30,810 32,640 32,640 32,640 32,640 32,640 34,990 34,990 34,990 34,990 34,990 37,230 37,230 37,230 37,230 37,230 39,380 39,380 39,380 39,380 39,380 41,420 41,420 41,420 41,420 41,420 －－

48,050

48,050 48,050 －－

50,490 50,490 50,490 －－

52,430 52,430 52,430 －－

54,980 54,980 54,980 －－

61,610 61,610 61,610 －－

68,240 68,240 68,240 －－

71,400 71,400 71,400 －－

74,770 74,770 74,770 －－－－

89,970 －－－－

93,330

Ds＝3 ：0～－0.006 3＜Ds≦6 ：0～－0.008 6＜Ds≦10 ：0～－0.00910＜Ds ：0～－0.011

（㎜）

直径公差

Ds＝3 ：0～－0.006 3＜Ds≦6 ：0～－0.008 6＜Ds≦10 ：0～－0.00910＜Ds ：0～－0.011

（㎜）

直径公差

●印：標準在庫品です。●：Stocked Items. □印：特定代理店在庫です。弊社営業へお問合せください。□：Stocked by specified distributor. Contact with our sales department. □印：特定代理店在庫です。弊社営業へお問合せください。□：Stocked by specified distributor. Contact with our sales department.●印：標準在庫品です。●：Stocked Items.

37,950 37,950 －－

39,890 39,890 39,890 －－

41,310 41,310 41,310 －－

43,350 43,350 43,350 －－

53,760 53,760 53,760 －－

55,800 55,800 55,800 －－

60,690 60,690 60,690 －－

62,730 62,730 62,730 －－－－

72,120 －－－－

74,160

23,360 23,360 23,360 23,360 23,360 23,360 23,360 23,360 23,360 23,360 23,360 23,670 23,670 23,670 23,670 23,670 23,970 23,970 23,970 23,970 23,970 24,590 24,590 24,590 24,590 24,590 25,100 25,100 25,100 25,100 25,100 26,730 26,730 26,730 26,730 26,730 28,360 28,360 28,360 28,360 28,360 30,500 30,500 30,500 30,500 30,500 32,540 32,540 32,540 32,540 32,540 34,280 34,280 34,280 34,280 34,280 35,910 35,910 35,910 35,910 35,910 －－

37,950

在庫一覧

形状・寸法

切削条件

15WHNSB -TH

溝長：R

全長：L

s 平面二段・S-X形シンニングPlane, S-X thinning

溝長：R

全長：L

20WHNSB -TH

Applications

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 8.0 8.1 8.2 8.3

40444450505054545454546363636363727272727281818181819191919191

100100100100100109109109109109118118118118118127127127127127136136136136136145145145145145154154154

838787939393

102102102102102111111111111111121121121121121132132132132132142142142142142151151151151151160160160160160171171171171171180180180180180191191191191191200200200200200209209209

3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 9.0 9.0 9.0

●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●□□●

在庫Stock

retail price(￥)

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

8.4 8.5 8.6 8.7 8.8 8.9 9.0 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9

10.0 10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 11.9 12.0 12.1 12.2 12.3 12.4 12.5 12.6 12.7 12.8 12.9 13.0

154154163163163163163172172172172172181181181181181190190190190190199199199199199208208208208208217217217217217226226226226226235235235235235

209209218218218218218227227227227227236236236236236245245245245245260260260260260269269269269269278278278278278287287287287287301301301301301

9.0 9.0 9.0 9.0 9.0 9.0 9.0

10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0

●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□□□●□□□□●

在庫Stock

retail price(￥)

3.0＜φDc＜6.0 6.0＜φDc＜10.0 10.0＜φDc≦13.0

上限Max

下限Min

－0.020

－0.036

－0.024

－0.045

－0.030

－0.053

15WHNSB

■15WHNSB直径公差表　Table of Tolerance on tool dia.

3.0＜φDc＜6.0 6.0＜φDc＜10.0 10.0＜φDc≦13.0

上限Max

下限Min

－0.020

－0.036

－0.024

－0.045

－0.030

－0.053

20WHNSB

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 8.0 8.1 8.2 8.3

505555626262676769696981818181819292929292

104104104104104116116116116116127127127127127139139139139139150150150150150162162162162162173173173173173185185185185185196196196

939898

105105105110110115115117129129129129129141141141141141155155155155155167167167167167178178178178178190190190190190203203203203203215215215215215228228228228228240240240240240251251251

3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 9.0 9.0 9.0

●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●□□●

在庫Stock

retail price(￥)

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

8.4 8.5 8.6 8.7 8.8 8.9 9.0 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9

10.0 10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 11.9 12.0 12.1 12.2 12.3 12.4 12.5 12.6 12.7 12.8 12.9 13.0

196196208208208208208219219219219219231231231231231243243243243243254254254254254266266266266266277277277277277289289289289289300300300300300

251251263263263263263274274274274274286286286286286298298298298298315315315315315327327327327327338338338338338350350350350350366366366366366

9.0 9.0 9.0 9.0 9.0 9.0 9.0

10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0

●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□□□●□□□□●

在庫Stock

retail price(￥)

26,930 26,930 26,930 26,930 26,930 26,930 26,930 26,930 26,930 26,930 26,930 27,340 27,340 27,340 27,340 27,340 27,650 27,650 27,650 27,650 27,650 28,260 28,260 28,260 28,260 28,260 28,870 28,870 28,870 28,870 28,870 30,810 30,810 30,810 30,810 30,810 32,640 32,640 32,640 32,640 32,640 34,990 34,990 34,990 34,990 34,990 37,230 37,230 37,230 37,230 37,230 39,380 39,380 39,380 39,380 39,380 41,420 41,420 41,420 41,420 41,420 －－

48,050

48,050 48,050 －－

50,490 50,490 50,490 －－

52,430 52,430 52,430 －－

54,980 54,980 54,980 －－

61,610 61,610 61,610 －－

68,240 68,240 68,240 －－

71,400 71,400 71,400 －－

74,770 74,770 74,770 －－－－

89,970 －－－－

93,330

Ds＝3 ：0～－0.006 3＜Ds≦6 ：0～－0.008 6＜Ds≦10 ：0～－0.00910＜Ds ：0～－0.011

（㎜）

直径公差

Ds＝3 ：0～－0.006 3＜Ds≦6 ：0～－0.008 6＜Ds≦10 ：0～－0.00910＜Ds ：0～－0.011

（㎜）

直径公差

●印：標準在庫品です。●：Stocked Items. □印：特定代理店在庫です。弊社営業へお問合せください。□：Stocked by specified distributor. Contact with our sales department. □印：特定代理店在庫です。弊社営業へお問合せください。□：Stocked by specified distributor. Contact with our sales department.●印：標準在庫品です。●：Stocked Items.

37,950 37,950 －－

39,890 39,890 39,890 －－

41,310 41,310 41,310 －－

43,350 43,350 43,350 －－

53,760 53,760 53,760 －－

55,800 55,800 55,800 －－

60,690 60,690 60,690 －－

62,730 62,730 62,730 －－－－

72,120 －－－－

74,160

23,360 23,360 23,360 23,360 23,360 23,360 23,360 23,360 23,360 23,360 23,360 23,670 23,670 23,670 23,670 23,670 23,970 23,970 23,970 23,970 23,970 24,590 24,590 24,590 24,590 24,590 25,100 25,100 25,100 25,100 25,100 26,730 26,730 26,730 26,730 26,730 28,360 28,360 28,360 28,360 28,360 30,500 30,500 30,500 30,500 30,500 32,540 32,540 32,540 32,540 32,540 34,280 34,280 34,280 34,280 34,280 35,910 35,910 35,910 35,910 35,910 －－

37,950

Applications

在庫一覧

形状・寸法

切削条件

30WHNSB -TH

溝長：R

全長：L

溝長：R

全長：L

With oil holeオイルホールあり L/D=30

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

30WHNSB0200-TH30WHNSB0210-TH30WHNSB0220-TH30WHNSB0230-TH30WHNSB0240-TH30WHNSB0250-TH30WHNSB0260-TH30WHNSB0270-TH30WHNSB0280-TH30WHNSB0290-TH30WHNSB0300-TH30WHNSB0310-TH30WHNSB0320-TH30WHNSB0330-TH30WHNSB0340-TH30WHNSB0350-TH30WHNSB0360-TH30WHNSB0370-TH30WHNSB0380-TH30WHNSB0390-TH30WHNSB0400-TH30WHNSB0410-TH30WHNSB0420-TH30WHNSB0430-TH30WHNSB0440-TH30WHNSB0450-TH30WHNSB0460-TH30WHNSB0470-TH30WHNSB0480-TH30WHNSB0490-TH30WHNSB0500-TH30WHNSB0510-TH30WHNSB0520-TH30WHNSB0530-TH30WHNSB0540-TH30WHNSB0550-TH30WHNSB0560-TH30WHNSB0570-TH30WHNSB0580-TH30WHNSB0590-TH30WHNSB0600-TH30WHNSB0610-TH30WHNSB0620-TH30WHNSB0630-TH30WHNSB0640-TH30WHNSB0650-TH30WHNSB0660-TH30WHNSB0670-TH30WHNSB0680-TH30WHNSB0690-TH30WHNSB0700-TH30WHNSB0710-TH30WHNSB0720-TH30WHNSB0730-TH30WHNSB0740-TH30WHNSB0750-TH30WHNSB0760-TH30WHNSB0770-TH30WHNSB0780-TH30WHNSB0790-TH

2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.55.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9

7077778787879494999999

116116116116116132132132132132149149149149149166166166166166182182182182182199199199199199215215215215215232232232232232248248248248248265265265265

113120120130130130137137144144147164164164164164181181181181181200200200200200217217217217217233233233233233250250250250250268268268268268285285285285285303303303303303320320320320

3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0

●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●

在庫Stock

retail price(￥)

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

30WHNSB0800-TH30WHNSB0810-TH30WHNSB0820-TH30WHNSB0830-TH30WHNSB0840-TH30WHNSB0850-TH30WHNSB0860-TH30WHNSB0870-TH30WHNSB0880-TH30WHNSB0890-TH30WHNSB0900-TH30WHNSB0910-TH30WHNSB0920-TH30WHNSB0930-TH30WHNSB0940-TH30WHNSB0950-TH30WHNSB0960-TH30WHNSB0970-TH30WHNSB0980-TH30WHNSB0990-TH30WHNSB1000-TH30WHNSB1010-TH30WHNSB1020-TH30WHNSB1030-TH30WHNSB1040-TH30WHNSB1050-TH30WHNSB1060-TH30WHNSB1070-TH30WHNSB1080-TH30WHNSB1090-TH30WHNSB1100-TH30WHNSB1110-TH30WHNSB1120-TH30WHNSB1130-TH30WHNSB1140-TH30WHNSB1150-TH30WHNSB1160-TH30WHNSB1170-TH30WHNSB1180-TH30WHNSB1190-TH30WHNSB1200-TH

8.08.18.28.38.48.58.68.78.88.99.09.19.29.39.49.59.69.79.89.9

10.010.110.210.310.410.510.610.710.810.911.011.111.211.311.411.511.611.711.811.912.0

265281281281281281298298298298298314314314314314331331331331331348348348348348364364364364364381381381381381397397397397397

320336336336336336353353353353353369369369369369386386386386386403403403403403425425425425425442442442442442458458458458458

8.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0

10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0

●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●

在庫Stock

retail price(￥)

29,480 29,480 29,480 29,480 29,480 29,480 29,480 29,480 29,480 29,480 29,480 30,600 30,600 30,600 30,600 30,600 36,620 36,620 36,620 36,620 36,620 40,600 40,600 40,600 40,600 40,600 44,480 44,480 44,480 44,480 44,480 49,580 49,580 49,580 49,580 49,580 51,920 51,920 51,920 51,920 51,920 58,960 58,960 58,960 58,960 58,960 60,490 60,490 60,490 60,490 60,490 71,100 71,100 71,100 71,100 71,100 73,340 73,340 73,340 73,340

73,340 －－

81,090 81,090 81,090 －－

89,250 89,250 89,250 －－

98,330 98,330 98,330 －－

108,120 108,120 108,120

－－

123,420 123,420 123,420

－－

136,680 136,680 136,680

－－

142,800 142,800 142,800

－－

149,940 149,940 149,940

直径2.0～3.0、3.5、4.0、4.5、5.0、5.5、6.0、6.5、7.0、7.5、8.0、8.5、9.0、10.0、11.0、12.0はh8となります。上記以外のアイテムは下表の直径公差になります。h8 for diameters of 2.0 to 3.0, 3.5, 4.0, 4.5, 5.0, 5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0, 10.0, 11.0,and 12.0. For other items, the diameter tolerance will be as in the table below.

Ds＝3 ：0～－0.006 3＜Ds≦6 ：0～－0.008 6＜Ds≦10 ：0～－0.00910＜Ds ：0～－0.011

（㎜）

直径公差

3.0＜φDc＜6.0 6.0＜φDc＜10.0 10.0＜φDc≦12.0

上限Max

下限Min

－0.020

－0.036

－0.024

－0.045

－0.030

－0.053

30WHNSB

25WHNSB -TH With oil holeオイルホールあり L/D=25

3.0＜φDc＜6.0 6.0＜φDc＜10.0 10.0＜φDc≦13.0

上限Max

下限Min

－0.020

－0.036

－0.024

－0.045

－0.030

－0.053

25WHNSB

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

2.02.12.22.32.42.52.62.72.82.93.03.13.23.33.43.53.63.73.83.94.04.14.24.34.44.54.64.74.84.95.05.15.25.35.45.55.65.75.85.96.06.16.26.36.46.56.66.76.86.97.07.17.27.37.47.57.67.77.87.98.08.18.28.3

●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●□□●

57626271717176768484849090989898

113113113113113127127127127127141141141141141155155155155155169169169169169183183183183183197197197197197211211211211211225225225225225239239239

100105105114114114119119132132132138138146146146162162162162162178178178178178192192192192192206206206206206220220220220220236236236236236250250250250250266266266266266280280280280280294294294

3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 9.0 9.0 9.0

在庫Stock

retail price(￥)

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

8.48.58.68.78.88.99.09.19.29.39.49.59.69.79.89.9

10.010.110.210.310.410.510.610.710.810.911.011.111.211.311.411.511.611.711.811.912.012.112.212.312.412.512.612.712.812.913.0

239239254254254254254268268268268268282282282282282297297297297297310310310310310324324324324324338338338338338353353353353353367367367367367

294294309309309309309323323323323323337337337337337358358358358358371371371371371385385385385385399399399399399414414414414414433433433433433

9.0 9.0 9.0 9.0 9.0 9.0 9.0

10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0

在庫Stock

retail price(￥)

28,260 28,260 28,260 28,260 28,260 28,260 28,260 28,260 28,260 28,260 28,260 28,970 28,970 28,970 28,970 28,970 32,130 32,130 32,130 32,130 32,130 34,480 34,480 34,480 34,480 34,480 36,720 36,720 36,720 36,720 36,720 40,190 40,190 40,190 40,190 40,190 42,330 42,330 42,330 42,330 42,330 47,030 47,030 47,030 47,030 47,030 48,860 48,860 48,860 48,860 48,860 55,290 55,290 55,290 55,290 55,290 57,430 57,430 57,430 57,430 57,430 －－

64,570

64,570 64,570 －－

69,870 69,870 69,870 －－

75,380 75,380 75,380 －－

81,600 81,600 81,600 －－

92,520 92,520 92,520 －－

102,000 102,000 102,000

－－

107,100 107,100 107,100

－－

112,200 112,200 112,200

－－－－

130,560 －－－－

134,640

直径2.0～3.0、3.5、4.0、4.5、5.0、5.5、6.0、6.5、7.0、7.5、8.0、8.5、9.0、10.0、11.0、12.0、13.0はh8となります。上記以外のアイテムは下表の直径公差になります。h8 for diameters of 2.0 to 3.0, 3.5, 4.0, 4.5, 5.0, 5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0 ,10.0, 11.0,12.0, and 13.0 For other items, the diameter tolerance will be as in the table below.

Ds＝3 ：0～－0.006 3＜Ds≦6 ：0～－0.008 6＜Ds≦10 ：0～－0.00910＜Ds ：0～－0.011

（㎜）

直径公差

●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□□□●□□□□●

Applications

在庫一覧

形状・寸法

切削条件

30WHNSB -TH

溝長：R

全長：Lφ

溝長：R

全長：L

With oil holeオイルホールあり L/D=30

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

30WHNSB0200-TH30WHNSB0210-TH30WHNSB0220-TH30WHNSB0230-TH30WHNSB0240-TH30WHNSB0250-TH30WHNSB0260-TH30WHNSB0270-TH30WHNSB0280-TH30WHNSB0290-TH30WHNSB0300-TH30WHNSB0310-TH30WHNSB0320-TH30WHNSB0330-TH30WHNSB0340-TH30WHNSB0350-TH30WHNSB0360-TH30WHNSB0370-TH30WHNSB0380-TH30WHNSB0390-TH30WHNSB0400-TH30WHNSB0410-TH30WHNSB0420-TH30WHNSB0430-TH30WHNSB0440-TH30WHNSB0450-TH30WHNSB0460-TH30WHNSB0470-TH30WHNSB0480-TH30WHNSB0490-TH30WHNSB0500-TH30WHNSB0510-TH30WHNSB0520-TH30WHNSB0530-TH30WHNSB0540-TH30WHNSB0550-TH30WHNSB0560-TH30WHNSB0570-TH30WHNSB0580-TH30WHNSB0590-TH30WHNSB0600-TH30WHNSB0610-TH30WHNSB0620-TH30WHNSB0630-TH30WHNSB0640-TH30WHNSB0650-TH30WHNSB0660-TH30WHNSB0670-TH30WHNSB0680-TH30WHNSB0690-TH30WHNSB0700-TH30WHNSB0710-TH30WHNSB0720-TH30WHNSB0730-TH30WHNSB0740-TH30WHNSB0750-TH30WHNSB0760-TH30WHNSB0770-TH30WHNSB0780-TH30WHNSB0790-TH

2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.55.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9

7077778787879494999999

116116116116116132132132132132149149149149149166166166166166182182182182182199199199199199215215215215215232232232232232248248248248248265265265265

113120120130130130137137144144147164164164164164181181181181181200200200200200217217217217217233233233233233250250250250250268268268268268285285285285285303303303303303320320320320

3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0

●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●

在庫Stock

retail price(￥)

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

30WHNSB0800-TH30WHNSB0810-TH30WHNSB0820-TH30WHNSB0830-TH30WHNSB0840-TH30WHNSB0850-TH30WHNSB0860-TH30WHNSB0870-TH30WHNSB0880-TH30WHNSB0890-TH30WHNSB0900-TH30WHNSB0910-TH30WHNSB0920-TH30WHNSB0930-TH30WHNSB0940-TH30WHNSB0950-TH30WHNSB0960-TH30WHNSB0970-TH30WHNSB0980-TH30WHNSB0990-TH30WHNSB1000-TH30WHNSB1010-TH30WHNSB1020-TH30WHNSB1030-TH30WHNSB1040-TH30WHNSB1050-TH30WHNSB1060-TH30WHNSB1070-TH30WHNSB1080-TH30WHNSB1090-TH30WHNSB1100-TH30WHNSB1110-TH30WHNSB1120-TH30WHNSB1130-TH30WHNSB1140-TH30WHNSB1150-TH30WHNSB1160-TH30WHNSB1170-TH30WHNSB1180-TH30WHNSB1190-TH30WHNSB1200-TH

8.08.18.28.38.48.58.68.78.88.99.09.19.29.39.49.59.69.79.89.9

10.010.110.210.310.410.510.610.710.810.911.011.111.211.311.411.511.611.711.811.912.0

265281281281281281298298298298298314314314314314331331331331331348348348348348364364364364364381381381381381397397397397397

320336336336336336353353353353353369369369369369386386386386386403403403403403425425425425425442442442442442458458458458458

8.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0

10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0

●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●

在庫Stock

retail price(￥)

29,480 29,480 29,480 29,480 29,480 29,480 29,480 29,480 29,480 29,480 29,480 30,600 30,600 30,600 30,600 30,600 36,620 36,620 36,620 36,620 36,620 40,600 40,600 40,600 40,600 40,600 44,480 44,480 44,480 44,480 44,480 49,580 49,580 49,580 49,580 49,580 51,920 51,920 51,920 51,920 51,920 58,960 58,960 58,960 58,960 58,960 60,490 60,490 60,490 60,490 60,490 71,100 71,100 71,100 71,100 71,100 73,340 73,340 73,340 73,340

73,340 －－

81,090 81,090 81,090 －－

89,250 89,250 89,250 －－

98,330 98,330 98,330 －－

108,120 108,120 108,120

－－

123,420 123,420 123,420

－－

136,680 136,680 136,680

－－

142,800 142,800 142,800

－－

149,940 149,940 149,940

直径2.0～3.0、3.5、4.0、4.5、5.0、5.5、6.0、6.5、7.0、7.5、8.0、8.5、9.0、10.0、11.0、12.0はh8となります。上記以外のアイテムは下表の直径公差になります。h8 for diameters of 2.0 to 3.0, 3.5, 4.0, 4.5, 5.0, 5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0, 10.0, 11.0,and 12.0. For other items, the diameter tolerance will be as in the table below.

Ds＝3 ：0～－0.006 3＜Ds≦6 ：0～－0.008 6＜Ds≦10 ：0～－0.00910＜Ds ：0～－0.011

（㎜）

直径公差

3.0＜φDc＜6.0 6.0＜φDc＜10.0 10.0＜φDc≦12.0

上限Max

下限Min

－0.020

－0.036

－0.024

－0.045

－0.030

－0.053

30WHNSB

25WHNSB -TH With oil holeオイルホールあり L/D=25

3.0＜φDc＜6.0 6.0＜φDc＜10.0 10.0＜φDc≦13.0

上限Max

下限Min

－0.020

－0.036

－0.024

－0.045

－0.030

－0.053

25WHNSB

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

2.02.12.22.32.42.52.62.72.82.93.03.13.23.33.43.53.63.73.83.94.04.14.24.34.44.54.64.74.84.95.05.15.25.35.45.55.65.75.85.96.06.16.26.36.46.56.66.76.86.97.07.17.27.37.47.57.67.77.87.98.08.18.28.3

●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●□□●

57626271717176768484849090989898

113113113113113127127127127127141141141141141155155155155155169169169169169183183183183183197197197197197211211211211211225225225225225239239239

100105105114114114119119132132132138138146146146162162162162162178178178178178192192192192192206206206206206220220220220220236236236236236250250250250250266266266266266280280280280280294294294

3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 9.0 9.0 9.0

在庫Stock

retail price(￥)

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

8.48.58.68.78.88.99.09.19.29.39.49.59.69.79.89.9

10.010.110.210.310.410.510.610.710.810.911.011.111.211.311.411.511.611.711.811.912.012.112.212.312.412.512.612.712.812.913.0

239239254254254254254268268268268268282282282282282297297297297297310310310310310324324324324324338338338338338353353353353353367367367367367

294294309309309309309323323323323323337337337337337358358358358358371371371371371385385385385385399399399399399414414414414414433433433433433

9.0 9.0 9.0 9.0 9.0 9.0 9.0

10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0

在庫Stock

retail price(￥)

28,260 28,260 28,260 28,260 28,260 28,260 28,260 28,260 28,260 28,260 28,260 28,970 28,970 28,970 28,970 28,970 32,130 32,130 32,130 32,130 32,130 34,480 34,480 34,480 34,480 34,480 36,720 36,720 36,720 36,720 36,720 40,190 40,190 40,190 40,190 40,190 42,330 42,330 42,330 42,330 42,330 47,030 47,030 47,030 47,030 47,030 48,860 48,860 48,860 48,860 48,860 55,290 55,290 55,290 55,290 55,290 57,430 57,430 57,430 57,430 57,430 －－

64,570

64,570 64,570 －－

69,870 69,870 69,870 －－

75,380 75,380 75,380 －－

81,600 81,600 81,600 －－

92,520 92,520 92,520 －－

102,000 102,000 102,000

－－

107,100 107,100 107,100

－－

112,200 112,200 112,200

－－－－

130,560 －－－－

134,640

直径2.0～3.0、3.5、4.0、4.5、5.0、5.5、6.0、6.5、7.0、7.5、8.0、8.5、9.0、10.0、11.0、12.0、13.0はh8となります。上記以外のアイテムは下表の直径公差になります。h8 for diameters of 2.0 to 3.0, 3.5, 4.0, 4.5, 5.0, 5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0 ,10.0, 11.0,12.0, and 13.0 For other items, the diameter tolerance will be as in the table below.

Ds＝3 ：0～－0.006 3＜Ds≦6 ：0～－0.008 6＜Ds≦10 ：0～－0.00910＜Ds ：0～－0.011

（㎜）

直径公差

●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□●●●□□□□●□□□□●

在庫一覧

形状・寸法

切削条件

Applications

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

04WNSB0100-TH04WNSB0110-TH04WNSB0120-TH04WNSB0130-TH04WNSB0140-TH04WNSB0150-TH04WNSB0160-TH04WNSB0170-TH04WNSB0180-TH04WNSB0190-TH04WNSB0200-TH04WNSB0210-TH04WNSB0220-TH04WNSB0230-TH04WNSB0240-TH04WNSB0250-TH04WNSB0260-TH04WNSB0270-TH04WNSB0280-TH04WNSB0290-TH04WNSB0300-TH04WNSB0310-TH04WNSB0320-TH04WNSB0330-TH04WNSB0340-TH04WNSB0350-TH04WNSB0360-TH04WNSB0370-TH04WNSB0380-TH04WNSB0390-TH04WNSB0400-TH04WNSB0410-TH04WNSB0420-TH04WNSB0430-TH04WNSB0440-TH04WNSB0450-TH04WNSB0460-TH04WNSB0470-TH04WNSB0480-TH04WNSB0490-TH04WNSB0500-TH04WNSB0510-TH04WNSB0520-TH04WNSB0530-TH04WNSB0540-TH04WNSB0550-TH04WNSB0560-TH04WNSB0570-TH04WNSB0580-TH04WNSB0590-TH04WNSB0600-TH04WNSB0610-TH04WNSB0620-TH04WNSB0630-TH04WNSB0640-TH04WNSB0650-TH04WNSB0660-TH04WNSB0670-TH04WNSB0680-TH04WNSB0690-TH04WNSB0700-TH04WNSB0710-TH04WNSB0720-TH04WNSB0730-TH

1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0 7.1 7.2 7.3

10101212141416161717171717191919191923232323232626262626292929292932323232323636363636393939393941414141414343434343454545

50505050505050505050505050505050505050505058585858585858585858646464646464646464647878787878787878787883838383838383838383909090

3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 8.0 8.0 8.0

●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●

在庫Stock

retail price(￥)

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

04WNSB0740-TH04WNSB0750-TH04WNSB0760-TH04WNSB0770-TH04WNSB0780-TH04WNSB0790-TH04WNSB0800-TH04WNSB0810-TH04WNSB0820-TH04WNSB0830-TH04WNSB0840-TH04WNSB0850-TH04WNSB0860-TH04WNSB0870-TH04WNSB0880-TH04WNSB0890-TH04WNSB0900-TH04WNSB0910-TH04WNSB0920-TH04WNSB0930-TH04WNSB0940-TH04WNSB0950-TH04WNSB0960-TH04WNSB0970-TH04WNSB0980-TH04WNSB0990-TH04WNSB1000-TH04WNSB1010-TH04WNSB1020-TH04WNSB1030-TH04WNSB1040-TH04WNSB1050-TH04WNSB1060-TH04WNSB1070-TH04WNSB1080-TH04WNSB1090-TH04WNSB1100-TH04WNSB1110-TH04WNSB1120-TH04WNSB1130-TH04WNSB1140-TH04WNSB1150-TH04WNSB1160-TH04WNSB1170-TH04WNSB1180-TH04WNSB1190-TH04WNSB1200-TH04WNSB1210-TH04WNSB1220-TH04WNSB1230-TH04WNSB1240-TH04WNSB1250-TH04WNSB1260-TH04WNSB1270-TH04WNSB1280-TH04WNSB1290-TH04WNSB1300-TH

7.4 7.5 7.6 7.7 7.8 7.9 8.0 8.1 8.2 8.3 8.4 8.5 8.6 8.7 8.8 8.9 9.0 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9

10.0 10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 11.9 12.0 12.1 12.2 12.3 12.4 12.5 12.6 12.7 12.8 12.9 13.0

454548484848485252525252545454545457575757576060606060636363636366666666667171717171737373737376767676767676767676

9090909090909096969696969696969696

104104104104104104104104104104112112112112112112112112112112121121121121121121121121121121128128128128128128128128128128

8.0 8.0 8.0 8.0 8.0 8.0 8.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0

10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0

●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●

在庫Stock

retail price(￥)

11,840 11,840 12,350 12,350 12,350 12,350 12,350 13,160 13,160 13,160 13,160 13,160 13,570 13,570 13,570 13,570 13,570 14,390 14,390 14,390 14,390 14,390 14,790 14,790 14,790 14,790 14,790 15,610 15,610 15,610 15,610 15,610 16,320 16,320 16,320 16,320 16,320 16,730 16,730 16,730 16,730 16,730 17,550 17,550 17,550 17,550 17,550 17,960 17,960 17,960 17,960 17,960 18,770 18,770 18,770 18,770 18,770

7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,860 7,860 7,860 7,860 7,860 8,260 8,260 8,260 8,260 8,260 8,870 8,870 8,870 8,870 8,870 9,420 9,420 9,420 9,420 9,420 9,980 9,980 9,980 9,980 9,980

10,410 10,410 10,410 10,410 10,410 10,410 10,410 10,410 10,410 10,410 11,020 11,020 11,020 11,020 11,020 11,840 11,840 11,840

04WNSB -TH

全長：L

溝長：R

オイルホールなしWithout oil hole

φ1～φ3 ：0～－0.014φ3.1～φ6 ：0～－0.018φ6.1～φ10 ：0～－0.022φ10.1～φ13 ：0～－0.027

0～－0.01（㎜）

全長：L

溝長：R

02WNSB -TH オイルホールなしWithout oil hole

L/D=2寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

02WNSB0300-TH02WNSB0310-TH02WNSB0320-TH02WNSB0330-TH02WNSB0340-TH02WNSB0350-TH02WNSB0360-TH02WNSB0370-TH02WNSB0380-TH02WNSB0390-TH02WNSB0400-TH02WNSB0410-TH02WNSB0420-TH02WNSB0430-TH02WNSB0440-TH02WNSB0450-TH02WNSB0460-TH02WNSB0470-TH02WNSB0480-TH02WNSB0490-TH02WNSB0500-TH02WNSB0510-TH02WNSB0520-TH02WNSB0530-TH02WNSB0540-TH02WNSB0550-TH02WNSB0560-TH02WNSB0570-TH02WNSB0580-TH02WNSB0590-TH02WNSB0600-TH02WNSB0610-TH02WNSB0620-TH02WNSB0630-TH02WNSB0640-TH02WNSB0650-TH02WNSB0660-TH02WNSB0670-TH02WNSB0680-TH02WNSB0690-TH02WNSB0700-TH02WNSB0710-TH02WNSB0720-TH02WNSB0730-TH02WNSB0740-TH02WNSB0750-TH02WNSB0760-TH02WNSB0770-TH02WNSB0780-TH02WNSB0790-TH02WNSB0800-TH

3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 8.0

151818181818202020202023232323232525252525252525252525252525252929292929313131313132323232323434343434

475252525252525252525259595959595959595959646464646464646464647171717171717171717176767676767676767676

3.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0

□□□□□□□□□□□□□□□□□□□□●●●□●●□□●□●□●□□●□□●●●□□●□●□□●●●

在庫Stock

retail price(￥)

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

02WNSB0810-TH02WNSB0820-TH02WNSB0830-TH02WNSB0840-TH02WNSB0850-TH02WNSB0860-TH02WNSB0870-TH02WNSB0880-TH02WNSB0890-TH02WNSB0900-TH02WNSB0910-TH02WNSB0920-TH02WNSB0930-TH02WNSB0940-TH02WNSB0950-TH02WNSB0960-TH02WNSB0970-TH02WNSB0980-TH02WNSB0990-TH02WNSB1000-TH02WNSB1010-TH02WNSB1020-TH02WNSB1030-TH02WNSB1040-TH02WNSB1050-TH02WNSB1060-TH02WNSB1070-TH02WNSB1080-TH02WNSB1090-TH02WNSB1100-TH02WNSB1110-TH02WNSB1120-TH02WNSB1130-TH02WNSB1140-TH02WNSB1150-TH02WNSB1160-TH02WNSB1170-TH02WNSB1180-TH02WNSB1190-TH02WNSB1200-TH02WNSB1210-TH02WNSB1220-TH02WNSB1230-TH02WNSB1240-TH02WNSB1250-TH02WNSB1260-TH02WNSB1270-TH02WNSB1280-TH02WNSB1290-TH02WNSB1300-TH

8.1 8.2 8.3 8.4 8.5 8.6 8.7 8.8 8.9 9.0 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9

10.0 10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 11.9 12.0 12.1 12.2 12.3 12.4 12.5 12.6 12.7 12.8 12.9 13.0

3636363636383838383840404040404141414141424242424244444444444646464646464646464649494949494949494949

80808080808080808080858585858585858585859090909090909090909094949494949494949494

100100100100100100100100100100

9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0

10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0

□□□●●●□●□●□□□●●□□●□●□●●□●●□●□●□□□●●●□●□●□●□□●●□□□●

在庫Stock

retail price(￥)

－－－

11,120 11,120 11,630 －

11,630 －

11,630 －－－

12,140 12,140 －－

12,750 －

13,260 13,260 －

13,260 13,880 －

13,880 －

13,880 －－－

14,490 14,490 14,900 －

14,900 －

15,510 －－

15,510 16,020 －－－

16,020

－－－－－－－－－－－－－－－－－－－－

8,010 8,490 8,490 －

8,490 8,490 －－

8,880 －

8,880 －－

9,430 9,430 9,430 －－

9,970 －

9,970 －－

10,510 10,510 10,510

φ3 ：0～－0.014φ3.1～φ6 ：0～－0.018φ6.1～φ10 ：0～－0.022φ10.1～φ13 ：0～－0.027

0～－0.01（㎜）

ラインナップ・再研磨Line Up, Re-gr inding

再研削・再コーティングの方法によっては、性能が20～40％に低下する場合もあります。また、再コーティングをしない場合は、さらに性能が低下し、チッピングや折損することがあります。本来の性能を得るには、弊社での再研削・再コーティングをおすすめします。御社内で再研削される場合は、刃先の面粗さ1.6S以下、両切れ刃の高さの差が（リップハイト）0.02mm以内になるように刃先を仕上げてください。

ホーニング幅Width of horning

（0.005～0.015）×直径 Dc(0.005 ~ 0.015) × Tool Dia. Dc

スクイ面 Cutting face

逃げ面Flank

1. Performance may deteriorate to 20%~40% of the initial performance due to the method of regrinding and re-coating. Without coating after regrinding, performance may be further reduced and cause chipping or breakage of the drill. It is recommended that you ask us to regrind and recoat your drill to maintain its performance.

2. When regrinding yourself, finish the cutting edge surface so that its roughness is 1.6S or less and the lip height difference is 0.02mm or less.

ドリルの再研磨＆再コーティングも承っております。詳しくは弊社営業所までお問い合せください。ドリルの再研磨＆再コーティングも承っております。詳しくは弊社営業所までお問い合せください。Drill regrinding/recoating orders accepted. Please contact our sales department.

再研磨 Re-grinding

在庫一覧

形状・寸法

切削条件

Applications

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

04WNSB0100-TH04WNSB0110-TH04WNSB0120-TH04WNSB0130-TH04WNSB0140-TH04WNSB0150-TH04WNSB0160-TH04WNSB0170-TH04WNSB0180-TH04WNSB0190-TH04WNSB0200-TH04WNSB0210-TH04WNSB0220-TH04WNSB0230-TH04WNSB0240-TH04WNSB0250-TH04WNSB0260-TH04WNSB0270-TH04WNSB0280-TH04WNSB0290-TH04WNSB0300-TH04WNSB0310-TH04WNSB0320-TH04WNSB0330-TH04WNSB0340-TH04WNSB0350-TH04WNSB0360-TH04WNSB0370-TH04WNSB0380-TH04WNSB0390-TH04WNSB0400-TH04WNSB0410-TH04WNSB0420-TH04WNSB0430-TH04WNSB0440-TH04WNSB0450-TH04WNSB0460-TH04WNSB0470-TH04WNSB0480-TH04WNSB0490-TH04WNSB0500-TH04WNSB0510-TH04WNSB0520-TH04WNSB0530-TH04WNSB0540-TH04WNSB0550-TH04WNSB0560-TH04WNSB0570-TH04WNSB0580-TH04WNSB0590-TH04WNSB0600-TH04WNSB0610-TH04WNSB0620-TH04WNSB0630-TH04WNSB0640-TH04WNSB0650-TH04WNSB0660-TH04WNSB0670-TH04WNSB0680-TH04WNSB0690-TH04WNSB0700-TH04WNSB0710-TH04WNSB0720-TH04WNSB0730-TH

1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0 7.1 7.2 7.3

10101212141416161717171717191919191923232323232626262626292929292932323232323636363636393939393941414141414343434343454545

50505050505050505050505050505050505050505058585858585858585858646464646464646464647878787878787878787883838383838383838383909090

3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 8.0 8.0 8.0

●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●

在庫Stock

retail price(￥)

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

04WNSB0740-TH04WNSB0750-TH04WNSB0760-TH04WNSB0770-TH04WNSB0780-TH04WNSB0790-TH04WNSB0800-TH04WNSB0810-TH04WNSB0820-TH04WNSB0830-TH04WNSB0840-TH04WNSB0850-TH04WNSB0860-TH04WNSB0870-TH04WNSB0880-TH04WNSB0890-TH04WNSB0900-TH04WNSB0910-TH04WNSB0920-TH04WNSB0930-TH04WNSB0940-TH04WNSB0950-TH04WNSB0960-TH04WNSB0970-TH04WNSB0980-TH04WNSB0990-TH04WNSB1000-TH04WNSB1010-TH04WNSB1020-TH04WNSB1030-TH04WNSB1040-TH04WNSB1050-TH04WNSB1060-TH04WNSB1070-TH04WNSB1080-TH04WNSB1090-TH04WNSB1100-TH04WNSB1110-TH04WNSB1120-TH04WNSB1130-TH04WNSB1140-TH04WNSB1150-TH04WNSB1160-TH04WNSB1170-TH04WNSB1180-TH04WNSB1190-TH04WNSB1200-TH04WNSB1210-TH04WNSB1220-TH04WNSB1230-TH04WNSB1240-TH04WNSB1250-TH04WNSB1260-TH04WNSB1270-TH04WNSB1280-TH04WNSB1290-TH04WNSB1300-TH

7.4 7.5 7.6 7.7 7.8 7.9 8.0 8.1 8.2 8.3 8.4 8.5 8.6 8.7 8.8 8.9 9.0 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9

10.0 10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 11.9 12.0 12.1 12.2 12.3 12.4 12.5 12.6 12.7 12.8 12.9 13.0

454548484848485252525252545454545457575757576060606060636363636366666666667171717171737373737376767676767676767676

9090909090909096969696969696969696

104104104104104104104104104104112112112112112112112112112112121121121121121121121121121121128128128128128128128128128128

8.0 8.0 8.0 8.0 8.0 8.0 8.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0

10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0

●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●

在庫Stock

retail price(￥)

11,840 11,840 12,350 12,350 12,350 12,350 12,350 13,160 13,160 13,160 13,160 13,160 13,570 13,570 13,570 13,570 13,570 14,390 14,390 14,390 14,390 14,390 14,790 14,790 14,790 14,790 14,790 15,610 15,610 15,610 15,610 15,610 16,320 16,320 16,320 16,320 16,320 16,730 16,730 16,730 16,730 16,730 17,550 17,550 17,550 17,550 17,550 17,960 17,960 17,960 17,960 17,960 18,770 18,770 18,770 18,770 18,770

7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,310 7,860 7,860 7,860 7,860 7,860 8,260 8,260 8,260 8,260 8,260 8,870 8,870 8,870 8,870 8,870 9,420 9,420 9,420 9,420 9,420 9,980 9,980 9,980 9,980 9,980

10,410 10,410 10,410 10,410 10,410 10,410 10,410 10,410 10,410 10,410 11,020 11,020 11,020 11,020 11,020 11,840 11,840 11,840

04WNSB -TH

全長：L

溝長：R

オイルホールなしWithout oil hole

φ1～φ3 ：0～－0.014φ3.1～φ6 ：0～－0.018φ6.1～φ10 ：0～－0.022φ10.1～φ13 ：0～－0.027

0～－0.01（㎜）

全長：L

溝長：R

02WNSB -TH オイルホールなしWithout oil hole

L/D=2寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

02WNSB0300-TH02WNSB0310-TH02WNSB0320-TH02WNSB0330-TH02WNSB0340-TH02WNSB0350-TH02WNSB0360-TH02WNSB0370-TH02WNSB0380-TH02WNSB0390-TH02WNSB0400-TH02WNSB0410-TH02WNSB0420-TH02WNSB0430-TH02WNSB0440-TH02WNSB0450-TH02WNSB0460-TH02WNSB0470-TH02WNSB0480-TH02WNSB0490-TH02WNSB0500-TH02WNSB0510-TH02WNSB0520-TH02WNSB0530-TH02WNSB0540-TH02WNSB0550-TH02WNSB0560-TH02WNSB0570-TH02WNSB0580-TH02WNSB0590-TH02WNSB0600-TH02WNSB0610-TH02WNSB0620-TH02WNSB0630-TH02WNSB0640-TH02WNSB0650-TH02WNSB0660-TH02WNSB0670-TH02WNSB0680-TH02WNSB0690-TH02WNSB0700-TH02WNSB0710-TH02WNSB0720-TH02WNSB0730-TH02WNSB0740-TH02WNSB0750-TH02WNSB0760-TH02WNSB0770-TH02WNSB0780-TH02WNSB0790-TH02WNSB0800-TH

3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 8.0

151818181818202020202023232323232525252525252525252525252525252929292929313131313132323232323434343434

475252525252525252525259595959595959595959646464646464646464647171717171717171717176767676767676767676

3.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0

□□□□□□□□□□□□□□□□□□□□●●●□●●□□●□●□●□□●□□●●●□□●□●□□●●●

在庫Stock

retail price(￥)

寸法 Size (mm)

直径Dc

Tool Dia.

溝長R

Flute Length

全長L

Overall Length

シャンク径Ds

Shank Dia.

02WNSB0810-TH02WNSB0820-TH02WNSB0830-TH02WNSB0840-TH02WNSB0850-TH02WNSB0860-TH02WNSB0870-TH02WNSB0880-TH02WNSB0890-TH02WNSB0900-TH02WNSB0910-TH02WNSB0920-TH02WNSB0930-TH02WNSB0940-TH02WNSB0950-TH02WNSB0960-TH02WNSB0970-TH02WNSB0980-TH02WNSB0990-TH02WNSB1000-TH02WNSB1010-TH02WNSB1020-TH02WNSB1030-TH02WNSB1040-TH02WNSB1050-TH02WNSB1060-TH02WNSB1070-TH02WNSB1080-TH02WNSB1090-TH02WNSB1100-TH02WNSB1110-TH02WNSB1120-TH02WNSB1130-TH02WNSB1140-TH02WNSB1150-TH02WNSB1160-TH02WNSB1170-TH02WNSB1180-TH02WNSB1190-TH02WNSB1200-TH02WNSB1210-TH02WNSB1220-TH02WNSB1230-TH02WNSB1240-TH02WNSB1250-TH02WNSB1260-TH02WNSB1270-TH02WNSB1280-TH02WNSB1290-TH02WNSB1300-TH

8.1 8.2 8.3 8.4 8.5 8.6 8.7 8.8 8.9 9.0 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9

10.0 10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 11.9 12.0 12.1 12.2 12.3 12.4 12.5 12.6 12.7 12.8 12.9 13.0

3636363636383838383840404040404141414141424242424244444444444646464646464646464649494949494949494949

80808080808080808080858585858585858585859090909090909090909094949494949494949494

100100100100100100100100100100

9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0

10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0

□□□●●●□●□●□□□●●□□●□●□●●□●●□●□●□□□●●●□●□●□●□□●●□□□●

在庫Stock

retail price(￥)

－－－

11,120 11,120 11,630 －

11,630 －

11,630 －－－

12,140 12,140 －－

12,750 －

13,260 13,260 －

13,260 13,880 －

13,880 －

13,880 －－－

14,490 14,490 14,900 －

14,900 －

15,510 －－

15,510 16,020 －－－

16,020

－－－－－－－－－－－－－－－－－－－－

8,010 8,490 8,490 －

8,490 8,490 －－

8,880 －

8,880 －－

9,430 9,430 9,430 －－

9,970 －

9,970 －－

10,510 10,510 10,510

φ3 ：0～－0.014φ3.1～φ6 ：0～－0.018φ6.1～φ10 ：0～－0.022φ10.1～φ13 ：0～－0.027

0～－0.01（㎜）

ラインナップ・再研磨Line Up, Re-gr inding

再研削・再コーティングの方法によっては、性能が20～40％に低下する場合もあります。また、再コーティングをしない場合は、さらに性能が低下し、チッピングや折損することがあります。本来の性能を得るには、弊社での再研削・再コーティングをおすすめします。御社内で再研削される場合は、刃先の面粗さ1.6S以下、両切れ刃の高さの差が（リップハイト）0.02mm以内になるように刃先を仕上げてください。

ホーニング幅Width of horning

（0.005～0.015）×直径 Dc(0.005 ~ 0.015) × Tool Dia. Dc

スクイ面 Cutting face

逃げ面Flank

1. Performance may deteriorate to 20%~40% of the initial performance due to the method of regrinding and re-coating. Without coating after regrinding, performance may be further reduced and cause chipping or breakage of the drill. It is recommended that you ask us to regrind and recoat your drill to maintain its performance.

2. When regrinding yourself, finish the cutting edge surface so that its roughness is 1.6S or less and the lip height difference is 0.02mm or less.

ドリルの再研磨＆再コーティングも承っております。詳しくは弊社営業所までお問い合せください。ドリルの再研磨＆再コーティングも承っております。詳しくは弊社営業所までお問い合せください。Drill regrinding/recoating orders accepted. Please contact our sales department.

再研磨 Re-grinding

在庫一覧

形状・寸法

切削条件

08WHNSB-TH

※次頁の加工方法を必ず参照ください。Be sure to refer to the boring procedure (next page) when selecting a tool.切削条件の選定について　Setting of Cutting Conditions

Applications

＊被削材、加工形状に合わせて、適切なクーラントを使用してください。＊この標準切削条件表は切削条件の目安を示すものです。実際の加工では加工形状、目的、使用機械等により条件を調整してください。＊この内部クーラント切削条件基準は希釈倍率20倍以下の水溶性切削油剤を使用する場合のものです。20倍を超える場合は切削速度範囲の下限を目安に使用してください。また、クーラントの供給圧はφ5.0 以下は2.0MPa以上を、φ5.0を超えるものは 1.5MPa以上を推奨いたします。＊MQL（ミスト）加工の場合は工具からの吐出量や吐出の状態により切削速度を下げないと加工できない場合があります。＊工具装着の際は傷や汚れの無いコレットを用い、工具の振れは0.02㎜以下に抑えてください。＊この切削条件は工具径の8倍までの穴深さに適用ください。＊油性の切削油剤を使用する場合は切削速度範囲の下限より低速の条件でご使用ください。また、切りくずおよび工具の発熱による発煙・引火にご注意ください。＊被削材は変形、たわみ、振動が起こらないようにしっかりと保持してください。＊条件表よりも低い回転数で使用することもできます。

※Use the appropriate coolant for the work material and machining shape.※These Recommended Cutting Conditions indicate only the rule of a thumb for the cutting conditions. In actual machining, the condition should be adjusted according to the machining shape, purpose and the machine type. ※The above cutting conditions are based on the use of a water-soluble coolant diluted to a maximum of 20 times. When coolant dilution exceeds 20 times, decrease the cutting speed to the lowest in the specified range. When the tool diameter isφ5.0 or less, the coolant pressure should be 2.0 MPa or higher, and when the diameter is over φ5.0, the pressure should be 1.5 MPa or higher.※When performing MQL (mist) machining, depending on the amount or status of spray from the tool, it may be necessary to reduce the cutting speed in order to perform machining.※When changing the tool, use collet free from flaws and stains and attach the tool firmly so that its runout is 0.02mm or less. ※The above conditions apply to a hole-depth of 8 times the diameter or less. ※When cutting fluid is used, reduce the cutting speed to a speed lower than the lowest

speed in the specified range. Take the greatest care to avoid smoke or ignition due to heating of chips and the tool.※Works should be gripped firmly to prevent deformation, deflection and vibration.※You can use borers at a revolution speed lower than the above values.

標準切削条件表Recommended Cut t ing Condi t ions

内部クーラントInternal coolant

７０～１２０～１５０

MQL（ミスト）MQL (mist)

５０～９０～１２０

７０～１２０～１５０

５０～９０～１２０

７０～１２０～１５０

５０～９０～１２０

４０～６０～８０

Φ4.0直径 Tool Dia.（mm）

Φ6.09500

Φ8.0 Φ10.0 Φ12.0

0.1～0.16

0.08～0.13

0.06～0.08

0.15～0.24

0.12～0.19

0.09～0.12

0.18～0.3

0.14～0.24

0.12～0.16

0.2～0.35

0.16～0.28

0.13～0.2

0.22～0.4

0.17～0.31

0.14～0.24

３０～４０～５０

１０～２０～３０

７０～１００～１２０

５０～９０～１２０

７０～１２０～１５０

５０～９０～１２０

0.05～0.1

0.1～0.16

0.08～0.14

0.15～0.24

0.12～0.18

0.18～0.3

0.15～0.2

0.2～0.35

４０～６０～８０

３０～５０～７０

0.08～0.13

0.12～0.19

0.14～0.24

0.16～0.28

0.18～0.32

0.17～0.22

0.22～0.4

２０～３０～４０

0.04～0.08

0.06～0.12

0.08～0.16

0.1～0.2

0.12～0.2

被削材（硬さ）Work material

(hardness)

切削速度（v c）Cutting speed(vc)

切削条件Cutting conditions

構造用鋼Structural steel

（～180HB）SS

炭素鋼Carbon steel

（～200HB）S○○C

合金鋼Alloy steel

（～30HRC）SCM

プリハードン鋼Prehardened steel

（～40HRC）

耐熱鋼INCONEL718Heatproof steel

ダクタイル鋳鉄Ductile ironFCD500

鋳物CastingFC250

（～50HRC）SKD

Ti合金Titanium alloyTi-6Al-4V

ステンレス鋼Stainless steelSUS300系・SUS400系

回転数(n)min-1

送り量（f ）mm/rev

回転数(n)min-1

Revolution speed (n)

Feed per Rev

Φ2.016000

0.05～0.1

0.03～0.06

0.02～0.04

0.04～0.06

0.03～0.05

0.05～0.1

0.02～0.03切削条件の選定について

Setting of Cutting Conditions

05WHNSB-TH03WHNSB-TH

※被削材、加工形状に合わせて、適切なクーラントを使用してください。※この標準切削条件表は切削条件の目安を示すものです。実際の加工では加工形状、目的、使用機械等により条件を調整してください。※この内部クーラント切削条件基準は希釈倍率20倍以下の水溶性切削油剤を使用する場合のものです。 20倍を超える場合は切削速

度範囲の下限を目安に使用してください。又クーラントの供給圧はφ5.0以下は2.0MPa以上を、φ5.0を超える物は1.5MPa以上を推奨いたします。

※MQL（ミスト）加工の場合は工具からの吐出量や吐出の状態により切削速度を下げないと加工できない場合があります。※工具装着の際は傷や汚れの無いコレットを用い、工具の振れは0.02 mm以下に抑えてください。※この切削条件は工具径の5倍までの穴深さに適用ください。※油性の切削油剤を使用する場合は切削速度範囲の下限より低速の条件でご使用ください。また、切りくずおよび工具の発熱による発

煙・引火にご注意ください。※被削材は変形、たわみ、振動が起こらないようにしっかりと保持してください。※条件表よりも低い回転数でご使用することもできます。※Use the appropriate coolant for the work material and machining shape.※These Recommended Cutting Conditions indicate only the rule of a thumb for the cutting conditions. In actual machining, the condition should be

adjusted according to the machining shape, purpose and the machine type. ※The above cutting conditions are based on the use of a water-soluble coolant diluted to a maximum of 20 times. When coolant dilution

exceeds 20 times, decrease the cutting speed to the lowest in the specified range. When the tool diameter is φ5.0 or less, the coolant pressure should be 2.0 MPa or higher, and when the diameter is over φ5.0, the pressure should be 1.5 MPa or higher.

※When performing MQL (mist) machining, depending on the amount or status of spray from the tool, it may be necessary to reduce the cutting speed in order to perform machining.

※When changing the tool, use collet free from flaws and stains and attach the tool firmly so that its runout is 0.02mm or less. ※The above conditions apply to a hole-depth of 5 times the diameter or less. ※When cutting fluid is used, reduce the cutting speed to a speed lower than the lowest speed in the specified range. Take the greatest care

to avoid smoke or ignition due to heating of chips and the tool.※Works should be gripped firmly to prevent deformation, deflection and vibration.※You can use borers at a revolution speed lower than the above values.

(hardness)

（～180HB）SS

（～200HB）S○○C

（～30HRC）SCM

（～40HRC）

ダクタイル鋳鉄Ductile iron

FCD500

鋳物Casting

（～50HRC）SKD

50～120～180

20～30～40

50～120～180

50～100～150

50～80～100

40～60～100

30～40～50

20～30～40

50～120～150

回転数(n)min-1

切削速度（vc）Cutting speed(vc)

切削条件Cutting conditions Φ4.0

直径 Tool Dia.（mm）

0.1～0.16

0.06～0.1

0.06～0.08

0.08～0.13

0.05～0.1

0.1～0.16

0.06～0.08

0.05～0.1

0.03～0.06

0.02～0.04

0.04～0.06

0.03～0.05

0.05～0.1

0.02～0.03

0.15～0.24

0.12～0.19

0.09～0.12

0.12～0.19

0.08～0.14

0.15～0.24

0.09～0.12

0.18～0.3

0.14～0.24

0.12～0.16

0.14～0.24

0.12～0.18

0.18～0.3

0.12～0.16

Φ10.0

0.2～0.35

0.16～0.28

0.13～0.2

0.16～0.28

0.15～0.2

0.05～0.2

0.2～0.35

0.13～0.2

Φ12.0

0.22～0.4

0.17～0.31

0.14～0.24

0.18～0.32

0.17～0.24

0.22～0.4

0.14～0.24

Revolution speed (n )