EBARA Self Priming Trash Pump EFQT/EFQU Section...

EBARA Self Priming Trash Pump EFQT/EFQUContents

Project: Model: Chk’d: Date:

EBARA Fluid Handlingwww.pumpsebara.com 1(803) 327-5005 (p) • (803) 327-5097 (f) rev. 12/11

Section Page

Model Designation 2

Features 3

Standard Specifications 5

Specifications 6

Selection Chart 7

Suction Speed Flow Chart 9

Performance Curves 10

Dimension Drawings 20

Technical Data 24

Sectional View 25

EBARA Self Priming Trash Pump EFQT/EFQUModel Designation



MODEL TYPE EFQ – self priming trash pump

HYDRAULICS T – Standard U – High Head

CONNECTION SIZE Suction x Discharge 2" (50mm) 2" (50mm) 3" (80mm) 3" (80mm) 4" (100mm) 4" (100mm) 6" (150mm) 6" (150mm) 8" (200mm) 8" (200mm) 10" (250mm) 10" (250mm) 12" (300mm) 12" (300mm)

MATERIALS OF CONSTRUCTION A – Standard: Ductile Iron Impeller / Cast Iron body

EFQ T 2 A

EBARA Self Priming Trash Pump EFQT/EFQUFeatures - EFQT



• Impellers are designed as a 2-vane, semi-open, solids handling up to 3" diameter solids, based on the pump size. Backside pump-out vanes reduce pressure on the seal and exclude solids from the seal area.

• Cartridge seal design allows for quick replacement and ease of installation.

• Removeable cover plates and rotating elements for quick inspection and cleaning of the pump without having to remove it from the piping.

EBARA Self Priming Trash Pump EFQT/EFQUFeatures - EFQU



• Impellers are designed as a Multivane, semi-open, high efficiency, solids handling up to 1.25" diameter solids. Backside pump-out vanes reduce pressure on the seal and exclude solids from the seal area.

• Cartridge seal design allows for quick replacement and ease of installation.

• Removeable cover plates and rotating elements for quick inspection and cleaning of the pump without having to remove it from the piping.

• EFQU-Series Pumps are dimensionally interchangeable with the EFQT series Pumps in the 3", 4" & 6" sizes.

EBARA Self Priming Trash Pump EFQT/EFQUStandard Specifications



EFQT EFQU

Discharge Size/Connection 2 to 12 inch 3 to 6 inch Flanged, F.F. ANSI Flanged, F.F. ANSIRange of HP 1 HP to 125 HP 1.5 HP to 75HPRange of Performance Capacity: to 3400 GPM 1500 GPM Head: to 130 feet to 210 feet

Maximum Solid Diameter 3 inch 1.25 inch

Speed 650 to 2150 RPM

Standard Materials Casing Cast Iron A48 CL 30 Impeller Ductile iron A 60-40-18 Wear Plate Carbon Steel SAE 1020 Cover Plate Cast Iron A48 CL 30 Shaft Alloy Steel 4140 Bearing Housing Cast Iron A48 CL 30 Flap Valve Reinforced Neoprene Seal Sleeve 316 Stainless Steel Flanges Cast Iron A48 CL 30 O-rings BunaMechanical Seal Silicon Carbide/Silicon Carbide , Viton, 316 Stainless Steel

Options Tungsten Carbide Seals Base-plate mounting, coupling guards Horizontal V -belt Vertical V- belt Flex coupled TEFC or OPD motors Diesel Engine operation, trailer or skid mounted NPT Threaded suction and discharge connections

*Note: Alternate construction materials avialable on request including 304ss, 316ss and CD4 MCU

EBARA Self Priming Trash Pump EFQT/EFQUSpecifications - EFQ



1. General: The pump(s) provided by Ebara are designed to provide maximum up time and ease of maintenance. They shall be horizontal, radial split, single stage, single suction and of a self priming design. The rotating element will be of back pullout design which can be removed without disturbing the flanged piping connections. The suction flange (front of casing) and discharge flange (top of casing) shall have a minimum rating of 125#.

a. CASING: The pump casing will be a material minimum of Grade A48, Cl 30 Cast Iron. Mounting feet will be integrally cast and sized to prevent tipping. Castings shall be smooth surfaces and free of blow holes and other casting irregularities.

The casing cover plate (top) used for filling will be 3 ½" in diameter and will be opened with a threaded hand clamp bar assembly.

Casing drain plug will be a minimum of 1-1/4" NPT for complete and rapid draining.

The front cover plate must be of sufficient size to permit removal of stoppages and allow service to the impeller, wear plate, and check valve without removing the suction or discharge piping. The cover plate is fitted with a handle for ease of maintenance. A pressure relief valve will be mounted on the front cover plate and designed to open at 75-200 psi.

The suction and discharge spool flanges shall be of one piece design and each fitted with a 1/4" NPT tapped holes with pipe plugs suitable for mounting gages and other equipment as desired.

The bearing housing will contain a fill plug and a sight gage for ease of monitoring oil level.

An integral suction check valve shall be provided, made of reinforced neoprene. The function of the check valve is to prevent reprime after every cycle, thereby, saving energy.

b. IMPELLER: The impeller shall be Ductile Iron A 60-40-18, single suction type, semi-open, non-clog type and threaded to the shaft and positively locked in position. The impeller shall be dynamically balanced and clearance shall be adjusted externally without use of shims or the dismantling of the pump. External clearance adjustment optimizes pump efficiency while extending the life of the impeller and the wear plate. Adjustment can be made with an Allen wrench (or equivalent). The impeller will be positively driven through a key mounted on the shaft.

The Model EFQT impeller is designed to handle solids up to 3" and the Model EFQU up to 1.25".

c. SHAFT: The heavy duty shaft is made of Alloy Steel 4140 and designed such that the minimum shaft deflection does not exceed .002 at the stuffing box.

d. SLEEVES: The shaft sleeves shall be of high quality Stainless steel material and sealed with o-ring to prevent leakage between the shaft and sleeve.

e. BEARINGS: Inboard and outboard bearings shall be anit-friction ball type, single or double row depending on pump model. Bearings shall be deep groove arranged for radial and / or axial loads as required by model configuration. Both sets of bearings shall be lubricated from a common reservoir.

f. MECHANICAL SEALS: Shaft seal faces shall be oil lubricated and the face material shall be SC/SC. The cage and spring shall be made of stainless steel and the elastomers shall be Viton.

g. BASE: Pump and motor/drive assembly shall be mounted on a common fabricated steel baseplate.

EBARA Self Priming Trash Pump EFQT/EFQUSelection Chart - EFQT



60

80

100

120

140

0

20

40

0 500 1000 1500 2000 2500 3000 3500

18

24

30

36

42

0

6

12

0 113 227 340 454 568 681 795

TDHm ft

USGPM

m3/hr

EFQT2EFQT3

EFQT6EFQT4 EFQT8 EFQT10EFQT12

Model EFQTSelection chart

EBARA Self Priming Trash Pump EFQT/EFQUSelection Chart - EFQU



Model EFQUSelection chart

100

125

150

175

200

225

0

25

50

75

31

38

46

53

61

68

0

8

15

23

0 300 600 900 1200 1500 1800

0 68 136 204 272 340 408

TDH

EFQU3 EFQU4 EFQU6

m ft

USGPM

m3/hr

EBARA Self Priming Trash Pump EFQT/EFQUSuction Speed Flow CurveProject: Model: Chk’d: Date:


EBARA Self Priming Trash Pump EFQT/EFQUPerformance Curves

Project: GPM: TDH: EFF: HP: Chk’d: Date:


� ��

EFQT2 Impeller Diameter: 6.38" S.G.: 1.0

Repriming Lifts

Figure NPSH prior to using above chart. DO NOT use as NPSH Suction Lift.1.5" Dia. Max. Spherical Solids.

Data SheetNet Weight: 203 lbs. (92kg)Shipping Weight: 252 lbs. (114kg)Impeller Dia.: 6-1/4" (158.75mm)R.P.M.: From 1150 RPM to 2900 RPMMax. Solids: 1-1/2" (44.45mm)





� ��

Repriming Lifts


Data SheetNet Weight: 404 lbs. (183kg)Shipping Weight: 452 lbs. (205kg)Impeller Dia.: 8-3/4" (222.3mm)R.P.M.: From 650 RPM to 2150 RPMMax. Solids: 2-1/2" (44.45mm)





� ��

Repriming Lifts


Data SheetNet Weight: 600 lbs. (295.5kg)Shipping Weight: 655 lbs. (280kg)Impeller Dia.: 9-3/4" (247.65mm)R.P.M.: From 650 RPM to 1950 RPMMax. Solids: 3" (76.2mm)





� ��

Repriming Lifts


Data SheetNet Weight: 802 lbs. (364kg)Shipping Weight: 862 lbs. (391kg)Impeller Dia.: 12-3/8" (314.32mm)R.P.M.: From 650 RPM to 1550 RPMMax. Solids: 3" (76.2mm)





� ��

Repriming Lifts





EFQT12 Impeller Diameter: 18" S.G.: 1


� ��

Repriming Lifts


Data SheetNet Weight: 2200 lbs. (998 kg)Shipping Weight: 2350 lbs. (1066 kg)Impeller Dia.: 18" (457.2mm)R.P.M.: From 650 RPM to 1250 RPMMax. Solids: 3" (76.2mm)



EFQU3 Impeller Diameter: 11" S.G.: 1


� ��

Repriming Lifts

Figure NPSH prior to using above chart. DO NOT use as NPSH Suction Lift.13/16" Dia. Max. Spherical Solids.

Data SheetNet Weight: 472 lbs. (214 kg)Shipping Weight: 497 lbs. (225 kg)Impeller Dia.: 11" (279.4mm)R.P.M.: From 850 RPM to 2150 RPMMax. Solids: 13/16" (20.63mm)



EFQU4 Impeller Diameter: 11" S.G.: 1


� ��

Repriming Lifts


Data SheetNet Weight: 600 lbs. (272 kg)Shipping Weight: 655 lbs. (297 kg)Impeller Dia.: 11" (279.4mm)R.P.M.: From 850 RPM to 2150 RPMMax. Solids: 1 1/8" (28.57mm)



EFQU6 Impeller Diameter: 12.5" S.G.: 1


� ��

Repriming Lifts


Data SheetNet Weight: 910 lbs. (413 kg)Shipping Weight: 965 lbs. (437 kg)Impeller Dia.: 12 1/2" (317.5mm)R.P.M.: From 850 RPM to 1950 RPMMax. Solids: 1 1/4" (31.75mm)

EBARA Self Priming Trash Pump EFQT/EFQUDimensions


Model EFQT 2, 3, 4, 6, 8


F

D

C

H

G

KJ L

B

Tw x d x lgKEYWAY

DISCHARGE Ø

SUCTION Ø

wd

ef

Ø

(n)QTY - (h)HOLESFLNAGEFLANGE

Q Q

R

F

M

EU

ØS x 4HOLES

(W)REQUIRED FOR REMOVAL OF BACK PLATE

N P

VA

DIMENSIONS (inch)SIZE MODEL

A B C D E F G H J K L M N P Q R S T U V W2 EFQT-2 13 1/4 24 11/16 21 3/4 17 13/16 6 13 1/2 - 1 3/4 10 9/16 6 7/16 14 1/16 2 7 3/16 8 7/8 5 13/16 11 5/8 9/16 3 1/2 1 1/8 22 6/8 73 EFQT-3 17 28 13/16 27 1/16 22 1/4 7 1/2 17 26 3/8 2 3/4 11 9/16 7 5/16 17 3/16 3 9 11 3/16 7 3/4 15 1/2 11/16 4 1 1/2 27 1/4 7 1/24 EFQT-4 20 31 7/8 29 1/4 25 3/4 8 3/4 19 1/2 29 3/4 2 3/4 12 1/2 8 15/16 19 1/2 3 1/16 11 11 9/16 9 18 11/16 5 1 1/2 30 7/8 96 EFQT-6 22 3/4 35 1/2 35 5/16 29 7/8 10 1/8 22 3/8 33 5/8 2 3/4 16 10 9/16 19 1/2 3 1/16 11 11 9/16 10 3/8 20 3/4 11/16 5 1 1/2 32 3/16 10 1/28 EFQT-8 27 3/4 40 1/4 42 1/16 37 13/16 13 28 1/2 39 3/4 0 16 1/4 12 5/8 24 4 12 16 12 1/2 25 7/8 6 11/16 1 3/4 38 5/8 13

PUMP

DIMENSIONS (mm)SIZE MODEL

A B C D E F G H J K L M N P Q R S T U V W50 EFQT-2 337 627 552 452 152 343 - 44 269 163 358 51 183 226 148 295 14.2 90 28.4 577 17880 EFQT-3 432 732 687 565 191 432 670 70 293 185 436 76 229 284 197 394 17.5 102 38.1 692 191

100 EFQT-4 508 809 742 654 222 495 756 70 317 226 495 78 279 294 229 457 17.5 127 38.1 784 229150 EFQT-6 578 902 896 759 257 568 854 70 406 268 495 78 279 294 264 527 17.5 127 38.1 817 267200 EFQT-8 705 1023 1068 960 330 724 1010 0 413 321 610 102 305 407 318 635 22.4 170 44.5 981 330

PUMP

Unit: inches

Unit: mm

e f n h2 4 3/4 6 4 3/43 6 7 1/2 4 3/44 7 1/2 9 8 3/46 9 1/2 11 8 7/88 11 3/4 13 1/2 8 7/8

FLANGEw d lg

1/4 1/8 23/8 3/16 33/8 3/16 3 1/23/8 3/16 3 1/23/8 3/16 5

KEYWAY

Unit: inches

Unit: mm

e f n h50 121 152 4 1980 152 191 4 19

100 191 229 8 19150 241 279 8 22200 298 343 8 22

FLANGEw d lg

6.4 3.0 519.7 4.8 769.7 4.8 899.7 4.8 899.7 4.8 127

KEYWAY



Model EFQT10


D

C

A J L

B

FLNAGE

H H

Tw

d

ef

Ø

SUCTION Ø

DISCHARGE Ø

w x d x lgKEYWAY

(n)QTY - (h)HOLESFLANGE

PN

M

E

U

ØS x 4HOLESQ Q

R

G

F F

e f n h10 14 1/4 16 12 1

FLANGEw d lg

3/8 3/16 3 3/4

KEYWAY

e f n h250 362 406 12 25

FLANGEw d lg

9.7 4.8 95

KEYWAY


A B C D E F G H J L M N P Q R S T U10 EFQT-10 30 15/16 48 11/16 48 1/16 41 14 25 1/16 27 3/4 15 1/2 28 20 11/16 4 12 12 11/16 12 1/2 25 7/8 4 13/16 1 3/4

PUMP


A B C D E F G H J L M N P Q R S T U250 EFQT-10 786 1237 1221 1041 356 637 705 393 711 525 102 305 322 318 635 22.4 122 44.5

PUMP

Unit: inches

Unit: mm

Unit: inches

Unit: mm



Model EFQT12


w d lg52/83 7/23 5 5/11

KEYWAY

e f n h300 432 483 12 25

FLANGE

e f n h12 17 19 12 1

FLANGE

w d lg16 8 139

KEYWAY


A B C D E F G H J K L M N P Q R S T U12 EFQT-12 32 63 13/16 56 1/16 20 20 38 1/4 18 3/8 13 5/8 38 5/16 20 25 9/16 10 5/8 8 10 3/4 9 9/16 16 1 1/16 6 9/16 2 3/4

PUMP


A B C D E F G H J K L M N P Q R S T U300 EFQT-12 813 1622 1424 508 508 972 467 346 973 508 649 270 203 273 243 406 27 167 69.9

PUMP

Unit: mm

Unit: inches

Unit: mm

Unit: inches

FLANGE



Model EFQU 3, 4, 6


G

H

F

D

C

KJ L

B

T

U

wd

DISCHARGE Ø

SUCTION Ø

w x d x lgKEYWAY

ef

Ø

(n)QTY - (h)HOLESFLNAGE

(W)

FLANGE

Q Q

R

A

MV

E

ØS x 4HOLES

N P

(W)REQUIRED FOR REMOVAL OF BACK PLATE

DIMENSIONS (inch)SIZE

A B C D E F G H J K L M N P Q R S T U V W3 EFQU-3 17 28 5/8 27 1/16 22 3/13 7 1/2 17 26 3/7 2 3/4 11 1/2 7 7/25 17 1/8 3 6 11 1/8 7 1/2 15 11/16 4 1/16 1 1/2 26 1/4 18 2/54 EFQU-4 20 29 11/16 29 2/3 26 1/4 8 3/4 20 30 3/16 2 3/4 11 8 15/16 18 7/8 3 13/16 7 3/16 11 11/16 9 18 11/16 4 15/16 1 1/2 29 9/16 186 EFQU-6 U6B60-B 23 33 35 5/16 29 7/8 10 1/8 22 3/8 33 29/50 2 3/4 16 10 14/25 20 15/16 3 1/16 7 15/16 13 10 3/8 20 3/4 11/16 4 1/2 1 3/4 33 1/4 20

MODEL PUMP

DIMENSIONS (mm)SIZE

A B C D E F G H J K L M N P Q R S T U V W80 EFQU-3 432 727 687 565 191 432 671 70 292 185 435 76 152 283 191 381 17.5 103 38.1 667 467

100 EFQU-4 508 754 754 667 222 508 767 70 279 227 480 97 183 297 229 457 17.5 126 38.1 752 457150 EFQU-6 U6B60-B 584 838 897 758 257 568 853 70 406 268 532 78 202 331 264 527 17.5 114 44.5 845 508

MODEL PUMP

Unit: inches

Unit: mm

e f n h3 6 7 1/2 4 3/44 7 1/2 9 8 3/46 9 1/2 11 8 7/8

FLANGEw d lg

19/50 15/79 33/8 3/16 3 1/23/8 3/16 3 9/16

KEYWAY

Unit: inches

e f n h80 152 191 4 19

100 191 229 8 19150 241 279 8 22

FLANGEw d lg10 5 769.7 4.8 899.7 4.8 90

KEYWAY

Unit: mm

EBARA Self Priming Trash Pump EFQT/EFQUTechnical Data


Cartridge Seal Assembly


SEAL PLATE

O-RINGS

SLEEVEO-RING

INTEGRAL SHAFT SLEEVE

SHEAR RING(SHEARED)

STATIONARY SEAT

STATIONARY ELEMENT

ROTATINGELEMENT

DRIVE BAND SPRINGCENTERING WASHER

BELLOWS

IMPELLER SHAFT

IMPELLER SHIMS

IMPELLER

SPRING

RATAINER

Model Inboard (front) Outboard (back)EFQT2EFQT3EFQT4 double rowEFQT6EFQT8EFQT10EFQT12 single row double row

EFQU3EFQU4EFQU6 double row double row

Bearing Types

single row double row

single rowsingle row

double row double row

EBARA Self Priming Trash Pump EFQT/EFQUSectional View


Model EFQT 2, 3


EBARA Self Priming Trash Pump EFQT/EFQUSectional View – Part Numbers


Model EFQT 2, 3


ITEM NO. PART NAME QTY PART NUMBER

01 PUMP CASING 01 02 * REPAIR ROTATING ASSY (Please refer to following page for detail) 01 03 SUCTION FLANGE 01 04 PIPE PLUG 01 05 HEX HD CAPSCREW 04 06 LOCKWASHER 04 07 * DISCH FLANGE GSKT 01 08 DISCHARGE FLANGE 01 09 NAME PLATE 0110 DRIVE SCREW 04 11 * VALVE ASSEMBLY 01 12 ROTATION DECAL 01 13 HEX HD CAPSCREW 04 14 LOCKWASHER 04 15 ROT ASSY SCREW SET 04 16 * WEAR PLATE ASSY 01 17 CASING DRAIN PLUG 01 18 * BACK COVER O’RING 01 19 HEX NUT 0220 LOCKWASHER 02 21 HAND NUT 01 22 STUD 02 23 BACK CVR PLATE ASSY 01 24 WARNING PLATE 01 25 DRIVE SCREW 04 26 CAUTION DECAL 01 27 PRESS RELIEF VALVE 01 28 * FILL COVER GASKET 01 29 HEX HD CAPSCREW 0430 LOCKWASHER 01 31 PIPE PLUG 01 32 CHECK VALVE PIN 01 33 PIPE PLUG 0134 CLAMP BAR 01 35 HEX HD CAPSCREW 02 36 * FILL COVER GASKET 01 37 CLAMP BAR SCREW 01 38 FILL COVER ASSY 01 39 WARNING PLATE 02 40 DRIVE SCREW 02 41 BACK COVER PLATE 02 42 HEX HD CAPSCREW 04 43 LOCKWASHER 04 * PARTS RECOMMENDED FOR STOCK



Model EFQT 2, 3 – Repair Rotating Assembly


DRIVE END VIEW

SEAL AREA DETAIL



Model EFQT 2, 3 – Repair Rotating Assembly


ITEM NO. PART NAME QTY PART NUMBER01 * IMPELLER 01 02 * SEAL ASSEMBLY 0103 SEAL PLATE 01 04 * INBOARD OIL SEAL 0105 * SEAL PLATE GASKET 01 06 BEARING HOUSE 01 07 * INBOARD BALL BEARING 0108 VENTED PLUG 01 09 * BEARING CAP OIL SEAL 0110 SOCKET HD CAPSCREW 01 11 AIR VENT 01 12 IMPELLER WASHER 0113 HEX HD CAPSCREW 04 14 LOCKWASHER 0415 BEARING CAP 0116 * SHAFT KEY 01 17 IMPELLER SHAFT 0118 BEARING RETAINING RING 01 19 SIGHT GAUGE 0120 PIPE PLUG 0121 * BEARING CAP GASKET 01 22 * OUTBOARD BALL BEARING 0123 BEARING HOUSING DRAIN PLUG 01 24 SEAL CAVITY DRAIN PLUG 0125 HEX HD CAPSCREW 0426 SEAL CAVITY DRAIN PLUG 01 27 SEAL PLATE O-RING 0128 ROTATING ASSY O-RING 01

* PARTS RECOMMENDED FOR STOCK



Model EFQT4




Model EFQT4



01 PUMP CASING 01 02 * REPAIR ROTATING ASSY (Please refer to following page for detail) 01 03 SUCTION FLANGE 0104 PIPE PLUG 01 05 HEX HD CAPSCREW 04 06 LOCKWASHER 04 07 * DISCH FLANGE GSKT 01 08 DISCHARGE FLANGE 01 09 NAME PLATE 01 10 DRIVE SCREW 04 11 * VALVE ASSEMBLY 01 12 ROTATION DECAL 01 13 HEX HD CAPSCREW 0414 LOCKWASHER 04 15 ROT ASSY SCREW SET 04 16 * WEAR PLATE ASSY 01 17 CASING DRAIN PLUG 01 18 * BACK COVER O’RING 01 19 HEX NUT 02 20 LOCKWASHER 02 21 HAND NUT 02 22 STUD 02 23 BACK CVR PLATE ASSY 01 24 WARNING PLATE 01 25 DRIVE SCREW 04 26 CAUTION DECAL 01 27 PRESS RELIEF VALVE 0128 BACK COVER PLATE 02 29 HEX HD CAPSCREW 04 30 LOCKWASHER 04 31 HEX HD CAPSCREW 08 32 LOCKWASHER 08 33 * SUCT CHK VALVE ASSY 01 34 CHECK VALVE PIN 01 35 PIPE PLUG 01 36 CLAMP BAR 01 37 MACHINE BOLT 0238 * FILL COVER GASKET 01 39 CLAMP BAR SCREW 01 40 FILL COVER ASSY 01 41 WARNING PLATE 01 42 DRIVE SCREW 02 43 PIPE PLUG 01




Model EFQT4 – Repair Rotating Assembly


DRIVE END VIEW

SEAL AREA DETAIL






01 * IMPELLER 0102 * SEAL ASSEMBLY 01 03 SEAL PLATE 0104 * INBOARD OIL SEAL 01 05 * SEAL PLATE GASKET 0106 BEARING HOUSE 01 07 * INBOARD BALL BEARING 0108 VENTED PLUG 01 09 * BEARING CAP OIL SEAL 0110 SOCKET HD CAPSCREW 01 11 AIR VENT 0112 IMPELLER WASHER 01 13 HEX HD CAPSCREW 0414 LOCKWASHER 04 15 BEARING CAP 0116 * SHAFT KEY 01 17 IMPELLER SHAFT 0118 BEARING RETAINING RING 01 19 SIGHT GAUGE 0120 PIPE PLUG 01 21 * BEARING CAP GASKET 0122 * OUTBOARD BALL BEARING 01 23 BEARING HOUSING DRAIN PLUG 0124 SEAL CAVITY DRAIN PLUG 01 25 HEX HD CAPSCREW 0426 LOCKWASHER 04 27 * SEAL PLATE O-RING 0128 * ROTATING ASSY O-RING 01 29 * SEAL PLATE O-RING 01




Model EFQT6




Model EFQT6



01 PUMP CASING 01 02 * REPAIR ROTATING ASSY (Please refer to following page for detail) 01 03 PIPE PLUG 01 04 PIPE PLUG 01 05 HEX HD CAPSCREW 0806 LOCKWASHER 08 07 DISCHARGE STICKER 01 08 DISCHARGE FLANGE 01 09 * DISCH FLANGE GSTK 01 10 NAME PLATE 01 11 DRIVE SCREW 04 12 ROT ASSY SCREW SET 06 13 ROT ASSY O-RING 01 14 HEX HD CAPSCREW 06 15 LOCKWASHER 0616 HEX HD CAPSCREW 06 17 LOCKWASHER 06 18 ROTATION DECAL 01 19 PIPE PLUG 01 20 * WAER PLATE ASSY 01 21 * BACK COVER O’RING 01 22 STUD 04 23 HEX NUT 04 24 LOCKWASHER 04 25 * BACK COVER O’RING 01 26 BACK CBR PLATE ASSY 01 27 WARNING PLATE 01 28 DRIVE SCREW 04 29 CAUTION DECAL 0130 PRESS RELIEF VALVE 01 31 BACK COVER PLATE 02 32 HEX HD CAPSCREW 04 33 LOCKWASHER 04 34 STUD 02 35 HAND NUT 02 36 * SUCTION FLANGEGASKET 01 37 SUCTION FLANGE 01 38 HEX HD CAPSCREW 08 39 LOCKWASHER 0840 SUCTION DECAL 01 41 PIPE PLUG 01 42 * VALVE ASSEMBLY 01 43 CHECK VALVE PIN 01 44 FILL COVER ASSY 01 45 WARNING PLATE 01 46 DRIVE SCREW 02 47 * FILL COVER GASKET 01 48 CLAMP BAR SCREW 01 49 MACHINE BOLT 02 50 CLAMP BAR 01 51 PIPE PLUG 01






SEAL AREA DETAIL

DRIVE END VIEW





ITEM NO. PART NAME QTY PART NUMBER 01 * IMPELLER 0102 * SEAL ASSEMBLY 01 03 SEAL PLATE 01 04 * SEAL PLATE GASKET 01 05 * INBOARD OIL SEAL 01 06 HEX HD CAPSCREW 0407 LOCKWASHER 04 08 BEARING HOUSE 01 09 * INBOARD VALL BEARING 01 10 VENTED SEAL CAVITY PLUG 01 11 VENTED SEAL CAVITY PLUG 01 12 * OUTBOARD OIL SEAL 01 13 HEX HD CAPSCREW 0614 LOCKWASHER 06 15 BEARING CAP 01 16 * SHAFT KEY 0117 IMPELLER SHAFT 01 18 BEARING RETAINING RING 01 19 * BEARING CAP O’RING 0120 * OUTBOARG BALL BEARING 01 21 * ROTATING ASSEMBLY O’RING 0122 * SEAL PLATE O’RING 01 23 IMPLLER WASHER 0124 IMPLLER CAPSCREW 0125 OIL LEVEL SIGHT GAUGE 01 26 PIPE PLUG 0127 PIPE PLUG 01 28 PIPE PLUG 0129 SEAL PLATE O-RING 01 * PARTS RECOMMENDED FOR STOCK



Model EFQT8




Model EFQT8



01 PUMP CASING 01 02 * REPAIR ROTATING ASSY (Please refer to following page for detail) 01 03 SUCTION FLANGE 01 04 CHECK VALVE PIN 01 05 * SUCT FLANGE GSKT 01 06 PIPE PLUG 01 07 HEX HD CAPSCREW 08 08 LOCKWASHER 08 09 DISCHARGE FLANGE 01 10 * DISH FLANGE GSKT 01 11 NAME PLATE 01 12 DRIVE SCREW 04 13 ROTATION DECAL 01 14 HEX HD CAPSCREW 06 15 LOCKWASHER 0616 HEX HD CAPSCREW 06 17 LOCKWASHER 06 18 CASING RING 01 19 ROT ASSY SCREW SET 06 20 * WEAR PLATE ASSY 01 21 PIPE PLUG 01 22 * BACK COVER O`RING 01 23 * PRESS RELIEF VALVE 01 24 STUD 03 25 LOCKWASHER 03 26 HEX NUT 03 27 HAND NUT 04 28 STUD 04 29 BACK COVER PLATE 0430 HEX HD CAPSCREW 08 31 LOCKWASHER 08 32 BACK COVER PLATE ASSY 01 33 WARNING PLATE 01 34 DRIVE SCREW 04 35 CAUTION DECAL 01 36 HEX HD CAPSCREW 08 37 LOCKWASHER 08 38 PIPE PLUG 01 39 PIPE PLUG 0140 SUCTION STICKER 01 41 * VALVE ASSEMBLY 01 42 DISCHARGE DECAL 01 43 PIPE PLUG 01 44 CLAMP BAR 01 45 HEX HD CAPSCREW 02 46 * FILL COVER GASKET 01 47 CLAMP BAR SCREW 01 48 FILL COVER ASSY 01 49 WARNING PLATE 0150 DRIVE SCREW 02






DRIVE END VIEW

SEAL AREA DETAIL





ITEM NO. PART NAME QTY PART NUMBER01 * IMPELLER 01 02 * SEAL PLATE GASKET 0103 * SEAL ASSEMBLY 01 04 * INBOARD BALL BEARING 01 05 BEARING HOUSE 01 06 PIPE PLUG 01 07 VENTED PLUG 01 08 * OUTBOARD BALL BEARING 01 09 * BRG HOUSING O`RING 01 10 BEARING CAP 01 11 IMPELLER SHAFT 01 12 * SHAFT KEY 01 13 * OUTBOARD OIL SEAL 01 14 BEARING RETAINING RING 01 15 HEX HD CAPSCREW 04 16 LOCKWASHER 04 17 * BEARING HOUSING O’RING 01 18 * INBOARD OIL SEAL 01 19 HEX HD CAPSCREW 04 20 LOCKWASHER 04 21 SEAL PLATE 01 22 * SEAL PLATE O’RING 01 23 IMPELLER WASHER 01 24 IMPELLER CAPSCREW 01 25 SIGHT GAUGE 01 26 PIPE PLUG 01 27 PIPE PLUG 01 28 PIPE PLUG 01 29 SEAL ASSEMBLY O-RING 01 * PARTS RECOMMENDED FOR STOCK



Model EFQT10




Model EFQT10


ITEM NO. PART NAME QTY PART NUMBER01 CASING 0102 * ROTATING ASSY (Please refer to following page for detail) 01 03 CHK VALV HSG ASSEMBLY04 CHECK VALVE BODY 01 05 PLUG 0106 SUCT CHK VALVE ASSEMBLY 01 07 * PIVOT CAP 0208 HX HD CAP SCREW 02 09 LOCKWASHER 0210 FLAT WASHER 02 11 * SHOULDER TYPE COUPLING 0112 CLEANOUT COV GASK 01 13 CLAMP BAR 0214 MACHINE BOLT 04 15 CLAMP BAR SCREW 0216 * CLEANOUT COVER ASSEMBLY 01 17 PIPE PLUG 0118 * SHIM SET 06 19 CASE RING 0120 HEX HEAD CAP SCREW 06 21 LOCKWAHER 0622 HEX HEAD CAP SCREW 06 23 LOCKWASHER 0624 FILL COVER ASSY 01 25 FILL COVER PLATE 0126 COVER GASKET 01 27 CLAMP BAR SCREW 0128 * MACHINE BOLT 02 29 CLAMP BAR 0130 BRG HSG O-RING 01 31 SEAL PLATE O-RING 0132 FRONT WEAR PLATE 01 33 PLUG 0134 SUCTION HD GASKET 01 35 PIPE PLUG 0136 * HX HD CAP SCREW 02 37 LOCKWASHER 0238 HX HD CAP SCREW 02 39 LOCKWASHER 0240 PRESS RELIEF VALVE 01 41 PIPE PLUG 0142 SUCTION HEAD 01






ITEM NO. PART NAME QTY PART NUMBER01 IMPELLER 0102 * SEAL ASSEMBLY 01 03 SEAL PLATE 0104 SEAL PLATE GASKET 01 05 BEARING HSG O-RING 0106 HEX HEAD CAPSCREW 04 07 * LOCKWASHER 0408 INBOARD BEARING 01 09 BEARING HOUSING 0110 VENTED PLUG 01 11 * AIR VENT 0112 REDUCING PIPE BUSH 01 13 BEARING CAP OILSEAL 0114 BEARING CAP 01 15 HEX HEAD CAPSCREW 0616 * LOCKWASHER 06 17 SHAFT KEY 0118 * IMPELLER SHAFT 01 19 BEARING SNAP RING 0120 OUTBOARD BEARING 01 21 BEARING CAP O-RING 0122 INBOARD OIL SEAL 01 23 INBOARD OIL SEAL 0124 LOCKWASHER 25 HEX NUT 26 WEAR PLATE ASSEMBLY 27 IMPELLER WASHER 0128 * IMPELLER CAPSCREW 01 29 SIGHT GAUGE 0130 SIGHT GAUGE 01 31 BEARING HSG DRAIN PLUG 01

31A SEAL CAV DRAIN PLUG 01 32 SOC HD PIPE PLUG 01 33 PIPE PLUG 0134 IMPELLER ADJ SHIM SET REF 35 SLEEVE O-RING 0136 * SOC HD PIPE PLUG 01 37 SEAL PLATE O-RING 0138 BEARING HSG O-RING 01 39 SHIPPING PLUG 0140 ASSEMBLY PLATE 01 41 DRIVE SCREW 02




Model EFQT12


SEAL AREA DETAIL



Model EFQT12



01 PUMP CASING 01 02 * IMPELLER 01 03 * SEAL ASSY 01 04 * VICTAULIC CPLG 01 05 ACCESS COVER ASSY 01 06 * COVER GSTK 01 07 COVER CLAMP 02 08 MACHINE BOLT 04 09 CLAMP BAR SCREW 02 10 * WEAR PLT ADJ SCREW 04 11 * WEAR PLT JAM NUT 04 12 PIPE PLUG 01 13 HEX HD CAPSCREW 12 14 LOCKWASHER 12 15 HEX NUT 12 16 DISCH ADAPTOR 01 17 ACCESSORY PLUG 01 18 * OIL SEAL 01 19 * DISCH FLANGE GSKT 01 20 PIPE PLUG 01 21 * WEAR PLT O-RING 01 22 * CASING O-RING 01 23 HEX HD CAPSCREW 02 24 LOCKWASHER 02 25 * SEAL CAVITY VENT 01 26 * PEDESTAL VENT 01 27 * WAVE WASHER 02 28 * OIL SEAL 01 29 * SHAFT KEY 01 30 * IMP SHAFT 01 31 BEARING CAP 01 32 * BALL BEARING 01 33 * BRG CAP O-RING 01 34 HEX HD CAPSCREW 06 35 LOCKWASHER 06 36 OIL SIGHT GAUGE 01 37 PIPE PLUG 01 38 PED DRAIN PLUG 01 39 BEARING HOUSE 01 40 * BALL BEARING 01 41 HEX HD CAPSCREW 20 42 LOCKWASHER 20 43 * PEDESTAL O-RING 01 44 SEAL PLATE 01 45 CASING DRAIN PLUG 01 46 PEDESTAL FOOT 01 47 STUD 04 48 LOCKWASHER 04 49 HEX NUT 04 50 STUD 04




Model EFQT12



51 LOCKWASHER 04 52 HEX NUT 04 53 * WEAR PL O-RING 01 54 * SCKT HD CAPSCREW 01 55 * IMPELLER WASHER 01 56 * IMP ROLL PIN 01 57 * IMPELLER KEY 01 58 HEX HD CAPSCREW 02 59 * WEAR PLATE 01 60 SUCTION ELBOW 01 61 HEX HD CAPSCREW 02 62 LOCKWASHER 02 63 * SEAL PLT O-RING 01 64 * SHAFT SLEEVE 01 65 * IMP SCREW SET 01 66 COVER PLT CLAMP 02 67 MACHINE BOLT 04 68 CLEANOUT CVR ASSY 01 69 CLAMP BAR SCREW 02 70 * COVER GSKT 01 71 SUCTION ELBOW 01 72 * PRES RELIEF VLV 01 73 PIPE PLUG 01 74 CHECK VALVE ASSY 01 75 HEX HD CAPSCREW 02 76 PIPE PLUG 02 77 FLAT WASHER 04 78 PIVOT CAP 02 79 CHECK VLV BODY 01 80 LOCKWASHER 02 81 * CHECK VALVE 01 82 AIR VENT 01 83 OIL LEVEL DECAL 01 84 SIGHT GAUGE ASSY 01 85 FLAT WASHER 02 86 BARBED ELBOW 01 87 BARBED ADAPTOR 01 88 PLASTIC TUBING 01 89 TUBING CLAMP 02 90 SEAL DRAING PLUG 03




Model EFQU 3, 4




Model EFQU 3, 4


ITEM NO. PART NAME QTY PART NUMBER01 PUMP CASING 0102 * REPAIR ROTATING ASSY (Please refer to following page for detail) 01 03 CHECK VALVE PIN 0104 SUCTION CHK VALVE ASSY 01 05 PIPE PLUG 0106 HEX HD CAPSCREW 04 07 * LOCKWASHER 0408 DISCHARGE FLANGE 01 09 DISCHARGE FLANGE GASKET 0110 MACHINE BOLT 02 11 * CLAMP BAR 0112 FILL COVER GASKET 01 13 FILL COVER ASSY 0114 WARNING PLATE 01 15 DRIVE SCREW 0216 * CLAMP BAR SCREW 01 17 PIPE PLUG 0118 * NAME PLATE 01 19 DRIVE SCREW 0420 HEX HD CAPSCREW 04 21 LOCKWASHER 0422 ROT ASSY SCREW SET 04 23 VENTED PLUG 0124 WEAR PLATE ASSY 01 25 BACK COVER O-RING 0126 STUD 04 27 HEX NUT 0428 * LOCKWASHER 02 29 BACK COVER O-RING 0130 PRESS RELIEF VALVE 01 31 BACK COVER PLATE ASSY 0132 WARNING PLATE 01 33 DRIVE SCREW 0434 CAUTION DECAL 01 35 STUD 0136 * HAND NUT 01 37 BACK COVER PLATE 0138 HEX HD CAPSCREW 04 39 LOCKWASHER 0440 LOCKWASHER 04 41 HEX HD CAPSCREW 0442 PIPE PLUG 01 43 VALVE ASSEMBLY 0144 SUCTION FLANGE 01 45 PIPE PLUG 0146 WARNING DECAL 01




Model EFQU 3, 4 – Repair Rotating Assembly


SEAL AREA DETAIL

DRIVE END VIEW



Model EFQU 3, 4 – Repair Rotating Assembly



01 * IMPELLER 01 02 * SEAL ASSEMBLY 01 03 SEAL PLATE GASKET 01 04 * INBOARD OIL SEAL 01 05 * BEARING HOUSE 01 06 INBOARD BALL BEARING 01 07 * VENTED PLUG 01 08 AIR VENT 01 09 * BEARING CAP GASKET 01 10 BEARING CAP 01 11 BEARING CAP OIL SEAL 01 12 IMPELLER SHAFT 01 13 SHAFT KEY 01 14 BEARING RETAINING RING 01 15 OUTBOARD BALL BEARING 01 16 * ROTATING ASSY O-RING 01 17 HEX HD CAPSCREW 04 18 LOCKWASHER 04 19 SEAL PLATE 01 20 SEAL PLATE O-RING 01 21 * IMPELLER WASHER 01 22 * SOCKET HD CAPSCREW 01 23 PIPE PLUG 01 24 HEX HD CAPSCREW 04 25 LOCKWASHER 04 26 SIGHT GAUGE 01 27 PIPE PLUG 01 28 PIPE PLUG 01 29 SEAL PLATE O-RING 01




Model EFQU6




Model EFQU6


ITEM NO. PART NAME QTY PART NUMBER 01 PUMP CASING 01 02 * REPAIR ROTATING ASSY (Please refer to following page for detail) 01 03 PIPE PLUG 01 04 PIPE PLUG 01 05 HEX HD CAPSCREW 0806 LOCKWASHER 08 07 DISCHARGE STICKER 01 08 DISCHARGE FLANGE 01 09 * DISCH FLANGE GSTK 01 10 NAME PLATE 01 11 DRIVE SCREW 04 12 ROT ASSY SCREW SET 06 13 ROT ASSY O-RING 01 14 HEX HD CAPSCREW 06 15 LOCKWASHER 0616 HEX HD CAPSCREW 06 17 LOCKWASHER 06 18 ROTATION DECAL 01 19 PIPE PLUG 01 20 * WAER PLATE ASSY 01 21 * BACK COVER O’RING 01 22 STUD 04 23 HEX NUT 04 24 LOCKWASHER 04 25 * BACK COVER O’RING 01 26 BACK CBR PLATE ASSY 01 27 WARNING PLATE 01 28 DRIVE SCREW 04 29 CAUTION DECAL 0130 PRESS RELIEF VALVE 01 31 BACK COVER PLATE 02 32 HEX HD CAPSCREW 04 33 LOCKWASHER 04 34 STUD 02 35 HAND NUT 02 36 * SUCTION FLANGEGASKET 01 37 SUCTION FLANGE 01 38 HEX HD CAPSCREW 08 39 LOCKWASHER 0840 SUCTION DECAL 01 41 PIPE PLUG 01 42 * VALVE ASSEMBLY 01 43 CHECK VALVE PIN 01 44 FILL COVER ASSY 01 45 WARNING PLATE 01 46 DRIVE SCREW 02 47 * FILL COVER GASKET 01 48 CLAMP BAR SCREW 01 49 MACHINE BOLT 0250 CLAMP BAR 01 51 PIPE PLUG 01




Model EFQU6 – Repair Rotating Assembly


SEAL AREA DETAIL

DRIVE END VIEW



Model EFQU6 – Repair Rotating Assembly


ITEM NO. PART NAME QTY PART NUMBER 01 * IMPELLER 0102 * SEAL ASSEMBLY 01 03 SEAL PLATE 0104 * SEAL PLATE GASKET 01 05 * INBOARD OIL SEAL 01 06 HEX HD CAPSCREW 0407 LOCKWASHER 04 08 BEARING HOUSE 0109 * INBOARD VALL BEARING 01 10 VENTED SEAL CAVITY PLUG 01 11 VENTED SEAL CAVITY PLUG 0112 * OUTBOARD OIL SEAL 01 13 HEX HD CAPSCREW 0614 LOCKWASHER 06 15 BEARING CAP 01 16 * SHAFT KEY 0117 IMPELLER SHAFT 01 18 BEARING RETAINING RING 0119 * BEARING CAP O’RING 0120 * OUTBOARG BALL BEARING 01 21 * ROTATING ASSEMBLY O’RING 0122 * SEAL PLATE O’RING 01 23 IMPLLER WASHER 0124 IMPLLER CAPSCREW 0125 OIL LEVEL SIGHT GAUGE 01 26 PIPE PLUG 0127 PIPE PLUG 01 28 PIPE PLUG 0129 SEAL PLATE O-RING 01 * PARTS RECOMMENDED FOR STOCK

EBARA Self Priming Trash Pump EFQT/EFQU Section...

Documents

Transcript of EBARA Self Priming Trash Pump EFQT/EFQU Section...