3 Easy Steps to InstallEZ-sensor® is a programmable TPMS sensor that must be programmed to

the specific Make, Model and Year of the vehicle being serviced.

1. Using one of the below TPMS scan tools, program EZ-sensor® to theMake, Model and Year of the vehicle being serviced.

Tool Brand ATEQ ATEQ ATEQ Bartec Bartec Bartec Bartec Bartec Bartec Bartec

Tool Part # VT-55* VT-56 VT-46 Tech 200 Tech 300SD Tech 300Pro Tech 400+ Tech 400SD Tech 400Pro Tech 500

Ships with EZ-sensor Software YES YES YES YES YES YES YES YES YES YES

TPMS Activation and Scan Functions YES YES YES YES YES YES YES YES YES YES

EZ-sensor is a trademark of Schrader International, Inc.December 2016

Compatible Programming Tools for

a

a

a/2

Tool Brand Bartec MAC Matco NAPA OTC Schrader Schrader Schrader Snap-on Snap-on

Tool Part # TPMS Pad ET 3824 TPR 3834 92-1525 3834 21230 EZ-programmer EZ-sensor Pad TPMS2 TPMS3

Ships with EZ-sensor Software YES YES YES YES YES YES YES YES YES NO

TPMS Activation and Scan Functions YES YES YES YES YES YES YES** YES YES YES

* VT-55 must have a SD card to be updated to program the new 33500 EZ-sensor

www.SchraderSensors.com // 1.800.288.1804Part of Sensata Technologies

** Must be upgraded to use as an activation tool

2. Once the sensors have been programmed, follow the attached mounting instructions to install the sensors into each rim.

3. A TPMS relearn is required to let the vehicle know that new sensorshave been installed.

Schrader is a brand of

Schrader Technical Support1.800. 288.1804

Assembly InstructionsMode d’emploi BedienungsanleitungManuale d’uso Instrucciones de Montaje

Schrader Performance Sensors1940 Opdyke CourtAuburn Hills, MI 48326Tech. Hotline: 1.800.288.1804E-mail: SchraderNA@sensata.comwww.SchraderSensors.com

10 2

4 5

MountingMontage

The Management of Schrader reserves the right to modify this leaflet and/or the products described therein without notice. Pictures for illustration purposes only.La direction de Schrader se réserve le droit de modifier cette notice et / ou les produits qui y sont décrits sans préavis. Photos uniquement à des fins d’illustration.La Dirección de Schrader se reserva el derecho de modificar este prospecto y / o los productos descritos en el mismo sin previo aviso. Fotos para fines de ilustración solamente.

6 7 8

1 2 3DismountingDesmontaje

Montaje

Démontage

44

A Inflate tire until both beads are securely in placeGonflez le pneu jusqu’à ce que les deux perles soient bien en placeInfle la llanta hasta que ambas perlas estén firmemente en su lugar

Inflate tire to recommended pressure

Gonflez le pneu à la pression recommandée

Infle el neumático a la presión recomendada

OUTEN DEHORSFUERA

INSORTIREN

5

B

C D

180o

CLICK!

Tire mounting pasteMontierpasteCreme montage pneus

Valve PullerExtracteur de ValveExtractor de Válvula

T-10 Torque ToolT-10 Pullertorque OutilT-10 Herramienta de Pullertorque de Válvula

• Never fit a damaged transmitter to a wheel rim• Do not fit the tire to the rim unless confident that the valve has been fitted correctly• Never re-use an old seal, or valve core if it has been removed from the valve stem.• Always ensure these components are replaced with new Schrader parts• Never re-use a nut, seat or valve steam if they are damaged. Always ensure these

components are replaced with new Schrader parts• Never fit a transmitter to unapproved wheel rims

3

Sn

ap-in Sensors

Max

210km/h

OR / OU / O

M= 1.4 ± 0.2 N.m*Please verify the right value on the boxS’il vous plaît vérifier la bonne valeur sur la boîtePor favor verifique el valor correcto en la caja

M= 1.4 ± 0.2 N.m

Sensors Types /Types deC / Modelos de SensoresRF Frequency 433.92MHz, RF Power < 10 mW

Mounting instruction adapted for these sensor typesInstructions de montages valables pour ces types de capteursInstrucciones de montaje adecuada para estos modelos de sensores

SW = T10

Snap-in

High Speed Snap-in (HS)

Faraday

15o

Valve PositionPosition de la VannePosición de la Válvula

• Ne jamais installer un capteur endommagée sur une jante• Ne monter pas le pneu sur la jante si vous n’etes pas certains que la valve ait été

correctement installée• Jamais utiliser un ancien corps de valve ou ancien joint si cela a été retiré du corps de

valve• Assurez-vous que les pièces sont remplacées par des pièces d’origine Schrader• Ne pas réutiliser une pièce défectueuse. Assurez vous de les remplacer par de nou-

velles pièces d’origine.• N’installez pas un capteur si la jante n’est pas compatible avec celui-ci.

• Nunca monte un transmisor dañado en una llanta• No monte el neumático con la llanta a no ser que esté seguro de que la válvula ha sido

ajustada correctamente• Nunca reutilice una junta antigua, o núcleo de válvula si estos han sido quitados del

pie de válvula.• Asegure siempre que estos componentes se sustituyen con piezas nuevas Schrader• Nunca reutilice una tuerca, asiento o pie de válvula si están dañados. Asegure siempre

que estos componentes se sustituyen con nuevas piezas Schrader• Nunca monte un transmisor con llantas no aprobadas

1.800.288.1804 www.SchraderSensors.com

TPMS COVERAGE IN ONE SENSOR ▶ Increase speed of service ▶ Optimze inventory levels and turns ▶ Eliminate potential lost sales ▶ Reduce overall cost of service

A SINGLE SENSOR SOLUTION ▶ Combines 314.9, 315 & 433 MHz applications

into ONE sensor ▶ Future proofed to support new and pending

OE system technologies ▶ Achieves OE quality requirements ▶ Replicates OE functionality, including

auto-locate technology

EZ-sensor Part #33500Rubber Snap-in Service Pack Part #20018 or #20008Aluminum Clamp-in Service Pack Part #34000

a brand of Sensata Technologies