Earth Day Doodle - The World's First and Best 3D Printing Pen...then keep doodling until it is at...

4
Final This tutorial will show you how to make an Earth Day Spinning Globe with the 3doodler pen in 15 steps. the3Doodler.com/Community | Copyright WobbleWorks, Inc. 2014 Earth Day Spinning Globe By Community

Transcript of Earth Day Doodle - The World's First and Best 3D Printing Pen...then keep doodling until it is at...

Page 1: Earth Day Doodle - The World's First and Best 3D Printing Pen...then keep doodling until it is at least 2 cm tall. Then attach “tree trunk 2” on top of “tree trunk 1”. *It

Final

This tutorial will show you how to make an Earth Day Spinning Globe with the 3doodler pen in 15 steps.

the3Doodler.com/Community | Copyright WobbleWorks, Inc. 2014

Earth Day Spinning GlobeBy Community

Page 2: Earth Day Doodle - The World's First and Best 3D Printing Pen...then keep doodling until it is at least 2 cm tall. Then attach “tree trunk 2” on top of “tree trunk 1”. *It

the3Doodler.com/Community | Copyright WobbleWorks, Inc. 2014

Step 1 Step 2

Step 3 Step 4

After Step 1, doodle another tree trunk that is at least3 cm tall.

Draw a circle at least the same size as your thumb, then keep doodling until it is at least 2 cm tall.

Then attach “tree trunk 2” on top of “tree trunk 1”.*It is up to you if you want it to be slanted or straight.

Now get a ball that is small (e.g golf ball) then wrap itwith tape.

Step 5

Doodle half of the ball, use a marker to mark where you started. Then take it off and doodle on the other side.*Remember to leave a hole.

2cm3cm

5cm

Leave holehere

Earth Day Spinning GlobeBy Community

Tree Trunk 1

Tree Trunk 2

Page 3: Earth Day Doodle - The World's First and Best 3D Printing Pen...then keep doodling until it is at least 2 cm tall. Then attach “tree trunk 2” on top of “tree trunk 1”. *It

the3Doodler.com/Community | Copyright WobbleWorks, Inc. 2014

Step 6 Step 7

Step 8 Step 9

Now cut a brown doodle strand that is at least 6.5 cm long.

After Step 5, attach the two hemispheres together.Then free doodle the world map. It does not matterif it is realistic or not.

Attach the doodle strand on top of the tree trunkvertically.

Now use the golf ball again and free doodle the tree branch. It does not matter if it is realistic or not. Youcan follow the picture too. Step 10

Free hand doodle two more tree branches.

6.5cm

Earth Day Spinning GlobeBy Community

Page 4: Earth Day Doodle - The World's First and Best 3D Printing Pen...then keep doodling until it is at least 2 cm tall. Then attach “tree trunk 2” on top of “tree trunk 1”. *It

the3Doodler.com/Community | Copyright WobbleWorks, Inc. 2014

Step 11 Step 12

Step 13 Step 14

Attach the short tree branches on the left and right side.Then attach the longer tree branch at the back.

Then free hand doodle the leaves on the treebranches.

Free hand doodle another short tree branch againat least half of the longest tree branch you made.

Then attach it to the longest tree branch. With the hole on the bottom of “the earth”, put it inside the strand until it comes out of the otherhole on top. Done!

Finally, attach the top of the branch on the tip of thestrand that is coming out of the hole and you are done!

Attach here

Earth Day Spinning GlobeBy Community