7/24/2019 E 135

1/2

ARDEX ENDURA (INDIA) PRIVATE LIMITEDCorporate Office & Regd. Office:Unit No. 406 & 407, Brigade Rubix,No. 20, HMT Campus, Yeshwanthapur Hobli,Bengaluru - 560013. Karnataka, INDIA.

CIN No: U24233KA1997PTC022383Tel: +91 80 66746500Fax: +91 80 66746540Email: customercare@ardexendura.comVisit us: www.ardexendura.com

Features

High performance polymer additive for cement and concrete mixes

Ideal for patching, can be feathered out to repair cracks and also for usein coving

Good workability and consistency

Water based - safe to use low odour and easy to clean

Admixture and Polymer BondingAgent (SBR)

E 135

7/24/2019 E 135

2/2

DESCRIPTIONE 135 is an SBR, multipurpose, concentrated,liquid polymer additive which when used withsand/cement, greatly improves the workabilityand consistency. It can also be used as anadmix for renders / screeds creatingworkability and consistency. E 135 can beapplied to damp surfaces (Saturated Surfaceno standing water) and can be rendered orpainted over.

SURFACE PREPARATIONThe surface to be treated should be clean,sound, free from oil, grease, laitance, dust,wax, polish and other barrier materials.

New concrete should be allowed to cure forat least 28 days.

New brickwork walls, sand / cement render orscreeds should be left for at least 7 daysbefore application of the Polymer bondingagent water resistant or binder coat.

APPLICATION AREAE 135 should be shake well before use.As a binder coat prior to applying renders ortoppings. As an admix for sand / cement mixesespecially in repair mortars, fillets, covings,renders and screeds. Prior to application ofPolymer bonding agent water resistant orbinder coat.

MIXINGAdmix for render / screed / coving: Mix 1 PartPolymer bonding agent with 3 parts water anduse as the gauging mix (mixing water) with a3 : 1 or 4 : 1 sand / cement mix.

Binder coat : 1 part E 135 : 1 part water :3 parts cement (by volume).

SLURRY COATMix to a thin binder and spread the mix over

the surface with brush or roller, or smallbroom. Maximum thickness recommended is2 mm. While the binder coat is still wet, applyrender or screed over it.Render/CovingApply binder coat on the prepared surface.While the binder coat is wet apply the Polymerbonding agent mortar mix with a wood floattrowel, ensuring firm pressure on the trowel towork the render into good contact with thesurface.

ScreedA minimum thickness of 15mm isrecommended when using diluted Polymer

bonding agent instead of water. For athickness greater than 40mm, reinforcing meshis required.

Using a roller, brush or a flat trowel, coat theprepared area with a binder coat of Polymerbonding agent to improve adhesion to thesubstrate.Apply the screed mix whilst the binder coat isstill wet using a straight edge, trowel or timberbatten to level the screed.

Achieve falls in shower recesses to a minimum1 : 60 : internal wet areas(eg bathrooms) to a minimum of 1 : 80 : andexternal areas to a minimum of 1 : 100.

Screeds should be left with a wood float finishto create a key for tiling and waterproofing.When reinforcing the screed with mesh, applyfirst layer of screed, lay in the mesh and applythe second layer of the screed. Do not lay themesh directly onto the substrate.

DRYING TIMEApproximately 16 hours (overnight) at 23 C and50% relative humidity when used for render /screed.

CURINGOn completion of the application, the surfacearea should be thoroughly cured withARDEX ENDURA C 20 concrete curing

compound or conventional water curing.

PROPERTIESThe values shown are typical of resultsobtained in the laboratory at 27 1 C. Actualperformance values obtained on site may varyfrom those quoted.

PHYSICAL PROPERTIES E 135 @ 27 1 C

Appearance White colour liquid

Specific Gravity 1.02 - 1.03

pH 8 - 10

Solid content 45%

VOC Content 4.18 g/L

PACK SIZE1 Litre, 5 Litres and 20 Litres.

STORAGE AND SHELF LIFEE 135 has a shelf life of 12 months if kept in adry, store between 5 C and 30 C in the originalunopened containers. The product should beprotected from frost, away from direct sunlightand sources of heat.

PRECAUTIONS

In case of contact with the eyes, rinseimmediately with plenty of water and seekmedical advice and after contact with the skinwash immediately with plenty of soap and water(do not use solvents). Prolonged contact with

the skin should be avoided. Always wear glovesand eye/face protection is necessary. Observepersonal hygiene, particularly washing thehands after work has been completed or at anyinterruption whilst work is in progress. Careshould be taken when removing gloves to avoidcontaminating the insides. In case of accidentsseek medical advice.

DISPOSAL/SPILLAGESpillage of any of the E 135 product should beremoved with plenty of water. Disposal of suchproduct or empty packaging should be inaccordance with local waste disposal authorityregulations.

For further information please refer to theMaterial Safety Data Sheet.

CONDITIONS OF SALESold subject to the Company's conditionsof sale which are available on request.

NOTEThe information supplied in this datasheet isbased upon extensive experience and is givenin good faith in order to help you. Our Companypolicy is one of continuous Research andDevelopment; we therefore reserve the right

to update this information at any time withoutprior notice. We also guarantee the consistenthigh quality of our products; however as wehave no control over site conditions or theexecution of the work, we accept no liabilityfor any loss or damage which may arise asa result thereof.

Admixture and Polymer Bonding Agent (SBR)E 135

0 4 / 1 5