DynaScan DS2012 / DS1508 Quickstart Guide
-
Upload
dynascan-technology-inc -
Category
Documents
-
view
275 -
download
2
description
Transcript of DynaScan DS2012 / DS1508 Quickstart Guide
Ver.1 DS1508 Quick Start Guide
1 Hardware Quick Start 1.1 Power Input and Consumption
The 220V (200~240V) AC Power Cable is single
phase, 3 wires.
Please follow the instruction to setup your power
cable with power source as below.
Line Number 3
Descriptions Line (Red)
Neutral (Black)
Ground (Green)
Requirement 16A@220VAC (Max.)
N (Black)
Ground (Green)
L (RED) Copyright © 2007 DynaScan Technology Corp. 1
Ver.1 DS1508 Quick Start Guide
1.2 System Connection Available Connection Type
G.S Model C.M Model
RS 485 connector Standard N/A
Fiber Transmitter Optional Standard
1.2.1 Connecting the 485 Converter (G.S Model)
IPC Video Capture Card
DVI Graphics Card
1ψ AC200V~240V 50/60Hz 20A
RS-485
Video Signal
Repeater
Control Box
Copyright © 2007 DynaScan Technology Corp. 2
Ver.1 DS1508 Quick Start Guide
The picture below shows how the 485 converter is connected.
The picture below shows how the video signal repeater is connected.
Connect to the RS485 single
connector of Control Box.
Connect to the COM1 of the
IPC.
Connect to the Display Connect to the DVI output
of the IPC.
Copyright © 2007 DynaScan Technology Corp. 3
Ver.1 DS1508 Quick Start Guide
1.2.2 Connecting the Giga Fiber Transmitter (G.S. & C.M. Model) 1.2.2 Connecting the Giga Fiber Transmitter (G.S. & C.M. Model)
1ψAC200V~240V 50/60Hz 20A
Expected Ceiling Mount Surface
Control Box
DVI Graphics Card
Video Capture Card
RS232
1ψAC100V~240V 50/60Hz 0.8A
Giga-Fiber Transmitter
Rx
IPC
The Length of Hanging Rod is 1M. For different length needs, please contact us. The Length of Hanging Rod is 1M. For different length needs, please contact us.
Danger : Ensure the concrete strength of the expected ceiling mount surface is no less than 3000 PSI. The ceiling mounted work must be done by civil engineering specialists. After the work is complete, we
advise that the reliability of it be checked and approved by authorities concerned in your area for
safety purpose.
Copyright © 2007 DynaScan Technology Corp. 4
Ver.1 DS1508 Quick Start Guide
The chart of how Giga Fiber Transmit ter is connected.
Port ○3 Connect to the PC
DVI Port.
Port ○2 Connect to the
COM1 of IPC.
PC DVI Port RS-232
Power Adapter
Giga Fiber Cable Connector Port ○4 Connect to the
Display.
Port ○1 Connect to the
adapter.
NOTE: 1. The Port ○1 above suppl ies Giga Fiber Transmit ter wi th the power.
2. Computer commands the transmit ter through the port ○2 . (RS-232 COM1 Connector)
Copyright © 2007 DynaScan Technology Corp. 5
Ver.1 DS1508 Quick Start Guide
1.3 IPC Installation There are two kinds of IPC (Standard IPC or Embedded IPC). Please choose the one you have for reference.
1.3.1 Standard IPC
Power Input
Keyboard/Mouse
Audio I/O
Video Capture Card
RJ-45 Connector
DVI Port
Monitor ConnectorCOM2
Wireless Card (Optional)
USB Ports COM1
(Display)
Power Switch
*Connect to D isp lay for Moni tor System
1.44” Floppy Disk
Power Button
USB Port
IBM 16X DVD-ROM
Reset Button
Follow the arrows to open the Front cover.
Copyright © 2007 DynaScan Technology Corp. 6
Ver.1 DS1508 Quick Start Guide
Connection of speakers T
1 2 3
he correct connection of the speakers
. Connect the Audio out port of the external device to the Audio in port of the capture card.
. Connect the Audio out port of the capture card to the Line in of the sound card with the enclosed male-male cable.
. Connect the speakers to the Audio out port of the sound card
Capture card Line Out
Enclosed male-male cable
Sound Card Line in
Dummy VGA Monitor Setup Steps
Wireless NIC (Optional) When you don’t use wireless network, please disable the Wireless NIC.
After you finish the setting and you wan to unplug the VGA Monitor, 1. Turn Off the IPC 2. Unplug the VGA Monitor Cable 3. Plug the Dummy VGA Monitor into the VGA Port and power on
the IPC You will see the content playing on the Display without the operating UI.
Dummy VGA Monitor
Copyright © 2007 DynaScan Technology Corp. 7
Ver.1 DS1508 Quick Start Guide
1.3.2 Embedded IPC Please install: 1. Dummy VGA Monitor 2. Audio Cable as the diagram.
2. Audio Cable Output the audio of Capture card to PC Please Connect the Audio Out and Line In as it shows
Use the NTSC/Pal switch connector for the
Capture Card if needed.
1. Dummy VGA Monitor Please Refer to the Appendix for more Info
Copyright © 2007 DynaScan Technology Corp. 8
Ver.1 DS1508 Quick Start Guide
1.4 Display Operation
1.4.1 Display ON / OFF Manually
Timer
Breaker
BREAKER:
The main power switch of the display is l
in the Control Box. After installation and setu
please keep the switch always on if you want
the display to power on / off automatic
ocated
p
ally.
UTO TIMER: display system automatically.
urn on:
ATo turn on / off
T
1. Turn on the IPC.
2. Setting Timer ON/OFF schedule.
3. Turn on the main power switch (Breaker) .
NOTE: The Timer must be setting on. Tu n off: Turn off the power switch of the IPC. r The display can be powered off by it self, or by main switch or by
timer.
Copyright © 2007 DynaScan Technology Corp. 9
Ver.1 DS1508 Quick Start Guide
1.4.2 ON / OFF Automatically You ca preset on and off for the display and IPC
Displayn at a certain time through the software application. When the
o. If preset time is up, the display will be powered on automatically, and the IPC will be triggered to power itself on to
you have preset the item of startup in the software application, the content of the assigned schedule or external
multimedia device will be played automatically. (Refer to the software manual for details)
NOTE: The main power switch and Timer must be always on.
1.4Panel
.3 Timer Setup
1. Initial Setup: the Breaker Switch.
s the “MODE” key for over 1 second for switching to
is complete.
2. G 1” mode.
the “+ “or “-“key and then press the
(a) Power on(b) Pres
“TIME ADJ” mode. (c) Set “day of week” by pressing the “+ “or “-“key. Then press the
“Enter” key when the setup(d) Set “hour” by pressing the “+ “or “-“key and then press the
“Enter” key when the setup is complete. (e) Set “minute” by pressing the “+ “or “-“key and then press the
“Enter” key when the setup is complete. Program One Time Setup: (a) Press the “MODE” key to switch to PRO(b) Set “hour” by pressing
“Enter” key when the setup is complete. (c) Set “minute” by pressing the “+ “or “-“key and then press the
“Enter” key when the setup is complete.
Copyright © 2007 DynaScan Technology Corp. 10
Ver.1 DS1508 Quick Start Guide
(d) Specify “ON” or “OFF” for output by using the “+” or “-“key and press the “Enter” button when the setup is
complete.
3. Program One Date Setup:
(a) Press the “MODE” key to switch to “PROG 1” “DAY SET” Mode.
(b) Pressing the “+” key will enable the first circuit as it is programmed or press the “-“key to disable it.
(c) Press the “Enter” key to make the change become valid.
(d) Repeat point 2 and 3 to set weekdays and weekends.
4. Program Two Time Setup:
(a) Press the “MODE” key to switch to “PROG 2” mode.
(b) Set “hour” by pressing the “+ “or “-“key and then press the “Enter” key when the setup is complete.
(c) Set “minute” by pressing the “+ “or “-“key and then press the “Enter” key when the setup is complete.
ode.
nge to “RUN” mode and switch both the manual override switch 1 and 2 to “RUN”
(d) Specify “ON” or “OFF” for output by pressing the “+” or “-“key and then press the “Enter” button when setup
is complete.
5. Program Two Date Setup:
(a) Press the “MODE” key for switching to “PROG 2”, “DAY SET” M
(b) Pressing the “+” key will enable the first circuit as it is programmed or press the “-“key to disable it.
(c) Press the “Enter” key to change the setting.
(d) Repeat point 2 and 3 to set weekdays and weekends.
6. Press “MODE” key to cha
position.
Copyright © 2007 DynaScan Technology Corp. 11
Ver.1 DS1508 Quick Start Guide
1.Yo
4.4 IPC Operation u can use LCM panel to operate the IPC without keyboard and mouse.
Basic Operation:
Power Indicator Display
ENTER:Enter the selected item or
save the setting
C:Go back or Cancel the setting
>)or
ES
Up/Down: Move the Cursor( Change the settings Command Buttons
.51.4 Put / Change ContentInsert Flash Media card*1,s
s uch as MS/MS PRO, SmartMedia, CF/MicroDrive and SD/MMC, ni to 8-in-1 Card
Reader for content playing.
. *1 Not include a Flash Media card
Copyright © 2007 DynaScan Technology Corp. 12
Ver.1 DS1508 Quick Start Guide
Steps
. Save contents to a Flash Media card. (Media files m
2. Insert media card into the 8-in-1 Ca
1 ust put in the root directory when you use LCM playing.)
rd Reader.
3. Choose the control item “Player Control”.
4. Choose the sub-menu “File Source”.
5. Select “All Content” to play the all media.
NOTE: 1.Refer to P.20~21 “Operation Tree of the IPC LCM” for more menu items, please. 2. For more instruction of IPC, please refer to the IPC User Manual.
Copyright © 2007 DynaScan Technology Corp. 13
Ver.1 DS1508 Quick Start Guide
1.4.6 Spin Speed Setting The spin speed of the display images. The more “X” is the faster it spins.
Steps
1. Choose the control item “Monitor System”.
2. Press Up to increase, or Down to decrease. “Fixed” means to stop spinning.
NOTE: 1.Refer to P.20~21 “Operation Tree of the IPC LCM” for more menu items, please.
2. For more instruction of IPC, please refer to the IPC User Manual.
Copyright © 2007 DynaScan Technology Corp. 14
Ver.1 DS1508 Quick Start Guide
2 Function / Maintenance Introduction
2.1.1 To activate AP3, click “START/Programs/ DynaScan AP3/DSPl
power on
Four Se
Section 1. Those buttons
2.1 AP3 Quick Operation
Start Program ayer to Start. Normally, the AP3 is running if PC
stored. when your computers are from DynaScan. Double click and AP3 will be re
2.1.2 Main Menu and Functions of Buttons ctions on Main Menu
are the main Menu of AP3
ection 2. Video Play control: This part is the control
bar for controlling the playing item
Section 3. Function operation area.
Section 4. Display monitor system.
S
Copyright © 2007 DynaScan Technology Corp. 15
Ver.1 DS1508 Quick Start Guide
2.1.3 Schedule Editing To setup the background sequence file, 5. Click to select schedule editing.
6. Set the Media type as Sequence File.
7. Drag the editing file as following picture.
d editing schedule.
1. Set the Media type as Sequence File
l2. C ick to select pa3. g the file to the box as followin
th and select the file you need. Dra g picture.
4. Save the sequence editing file.
8. Select the media file you need.
9. Drag the file to the box an
Copyright © 2007 DynaScan Technology Corp. 16
Ver.1 DS1508 Quick Start Guide
2.1.4 Edit Layout Presetting Layout AP pro3 e layvides seven layout settings. Click th out you wa
you can start to edit. The Preset layouts are undeletable.
nt, AP3 will load the layout into the editing section and
Content Setting There is no content for newly made layout frames. If you do not assign any content to one frame, it will display a
black ground when playing. Click Start Run button to summon the Startup Run Setup window, and then assign
the content and the description of this content. The content with parameters to adjust will show the button beside description, and you can click it to setup.
Copyright © 2007 DynaScan Technology Corp. 17
Ver.1 DS1508 Quick Start Guide
Copyright © 2007 DynaScan Technology Corp. 18
Ver.1 DS1508 Quick Start Guide
2.1.5 Image Spin Speed elect the spin speed of the image(s) on the display screen. It is a drop
hanged, 8 Sec, 16 Se The 8 Sec. means the drum image t
efault setting is “Fixed at image(s) is displayed on the screen in
ny of them to
S -down list, and the options cannot be
a nd. The
n choose
c c, -- to 120 Sec.
”. This means th
fit your needs.
kes 8 seconds to rotate a rou
a fixed position. You cad
a
Copyright © 2007 DynaScan Technology Corp. 19
Ver.1 DS1508 Quick Start Guide
2.2 round MountingG (G.S Model)
For Safety Reason, you must do the ground mounting to fix the display on the ground.
Steps
1. Stop the casters.
2. Lift the display a little up by counterclockwise turning the stoppers with tools.
Copyright © 2007 DynaScan Technology Corp. 20
Ver.1 DS1508 Quick Start Guide
3 Reference 3.1 Specifications Model DS1508
LED Type Chip Lamp
Pitch (H x V) 1.9mm x 1.7mm
Resolution 864 x 512 x 3screen
Brightness > 500 cd/㎡ > 1500 cd/㎡
Color 16.7 millions
Contrast Ratio > 5000 : 1
Screen Size (Diagonal) 73” Diagonal x 3
Total Display Area (W x H) 1.64 m x 0.87 m x 3
Viewing Angle(H x V) >170 o x 120 o >170 o x 60 o
Display Area (D x H) Φ1.57M x 0.87M
Physical Dimension (D x H) Φ1.7 M x 2.58 M(G.S) / 2.9M(C.M)
Physical Weight 600Kg
Power Supply 200~240 VAC, 50/60 Hz, 1Φ (220V),20A
Color Spectrum Red: 660nm Green: 525nm Blue: 470nm
Safe Ambient Temperature From 0o to 30o C
Copyright © 2007 DynaScan Technology Corp. 21
Ver.1 DS1508 Quick Start Guide
3.2 Operation Tree
M
of the IPC LCM
a Menu Level 1in M Menu Level 2 Menu Level 3 Main Menu l 1 Menu Level 2 Menu Level 3Pla
enu Menu Levey All Spin Speed
Power Oname Power Off
Media File
CloseSelect Fr
Adj Dis ForwardAdj Dis ReversePicture File
Sequence FileSchedule FileLayout File System Run Time
All Media S
TemperaturePower / Motor
ystem AlarmAll PictureAll ContentSVideoAV
hannel
eTwo
ThreeCF/MicroDriveSD/MMCMS/MSProSmartMediaHard Disk
One File --------------
Player Con
ce ---------
-----
-----
Monitor Syst
Virtual Enc.BrightnessLEDM ON/OFF
Tuner CPlaytrolPauseStopNext
Play Operator -------
Prev.Volume
On
CloneTwo Clone
Layout ----------------
File Sour
Video Source --
Content Device
em
Copyright © 2007 DynaScan Technology Corp. 22
Ver.1 DS1508 Quick Start Guide
Main Menu Menu Level 1 Menu Level 2 Menu LevelOS ProtectClock
Country Code
3 Main Menu Menu Level 1 Menu Level 2 Menu Level 3WhiteRedGreen
Cable BlueAntenna No Red
Input Pin No GreenDHCP Enable No BlueIP Address WhiteSubnet Mask RedDefault Gateway GreenSet BlueCancel No RedHost Name No GreenStartup No BlueStartup TimeShutdownShutdown TimeRebootReboot TimeWatchdogWatchdog TimerLeft Pos.Top PosWidthHeightBrightnessContrastGammaDVIVGA
Back LightCF/Micro DriveSD/MMCMS/MSPROSmart MediaStableUnstable
Video Out -------------
Input Type -----------
Option Setting
Test Pattern
Pure Color ----------
Level Color ----------
Tuner ----------------
Update Program----
Embedded OS-------
Display Setting ------
Window Adjust -----
Auto Run ------------
Network --------------
Watchdog------------
NOTE: For more instruction of IPC, Please refer to the IPC User Manual.
Copyright © 2007 DynaScan Technology Corp. 23
Ver.1 DS1508 Quick Start Guide
3.3 Dimension
3.3.1 Ground Stand Model
Copyright © 2007 DynaScan Technology Corp. 24
Ver.1 DS1508 Quick Start Guide
3.3.2 Ceiling Mount Model
Copyright © 2007 DynaScan Technology Corp. 25
Ver.1 DS1508 Quick Start Guide
3.4 AP3 Default Settings
Click to start option settings. Default settings are shown below. Setting
Items Function \ Model DS1508 Remark
Startup
Setting
Select Model DS1508 Default setting.
Accelerator VMR9_WL Default setting.
Screen Type Screen2 Default setting.
Auto Startup Enable To auto activate AP3 when the computer starts.
Biling Record Enable User Define Activate the function to keep the log. It needs to reopen AP3 to enable the setting.
Computer ID User Define To set a computer ID number for Biling Record for easy maintenance.
VMR9_RL Frame Reversal Disable It's necessary to check it when you'd like to display a upside down content. Select VMR9_RL as accelerator and close it. Reopen AP3 to enable the setting.
Content in Sequence Preload User Define To shorten the blank interval between clips. It only supports Media File, Capture & Picture. Accelerator VMR9 _ WL supports this function.
Content in Schedule Preload User Define To shorten the blank interval between clips. It only supports Media File, Capture & Picture.
Sequence in Schedule Preload User Define To shorten the blank interval between clips. It only supports Media File, Capture & Picture.
Copyright © 2007 DynaScan Technology Corp. 26
Ver.1 DS1508 Quick Start Guide
Copyright © 2007 DynaScan Technology Corp. 27
Setting Function \ Model
Items DS1508 Remark
Monitor
System
stem connection port. Serial Port COM1 Select Monitor Sy
Protoc Select a correct monitor syste Default setting is Auto. ol Ver. Auto m edition.
Display Adjust
Forward: Move the screen clockwise.
the screen counterclockwise. User Define Reverse: Move
Save: Save the setting.
Power Control Enable
rn ON or OFF the display power.
ntil six minutes
e
ountdown is due by pressing the “Force Power
Power On” may cause damage to the display.
ting.
Enable
Forcefully tu
After Power off, you can’t power on the display u
later. This is for the safety reason. However you can power on th
display before the c
On”.
Warning: “Force
Please don’t press the button unless you are sure that the display is
completely stop opera
Outside Power Off Enable Enable
ill shut the display as well.
Check the checkbox to enable the setting. When the IPC is turned
off by any way except the shutdown time, such as pressing the
Power button. IPC w
NOTE: For more instruction of AP3, please refer to the AP3 Software Manual.
Ver.1 DS1508 Quick Start Guide
3.5 Ltelle
egal Notices In ctual ited license to users
The hardware and software of our products are protected by copyr ight, t rademark, patent, and/or te l lectual property laws nd any tware, t rademarks contain may vio late such la nd theexpres ed herein, DynaScan d i ts sup d r ights to use any product re lated hardware and
Dy registered tradem naScountr ft is registered tr of t rademark of Moonl ight cordless Ltd. IBM is regi of IBM Corporat ion. Other t rademarks are trademarks of their respect ive oDisclaimer
eci f icat ions and information contained herein ardically made to the information herein; these revisions
c in the products or the programs described manotice, a strued as a com t madtypographical errors. DynaScan assumes no responsibility appear in this manual. Exclusion of Damages:
DynaScan Technology Corporat ion’s l iabi l i ty of repair or replacement of the product.
DynaScan Technology Corporat ion shal l no1. property c by an on
inconvenience, loss of use of the product ss of business opportuni ty, loss of goodwi l l , interferenc other commercial loss, even i f advised of the possibi l i ty of such damages.
2. Any other damages, whether inc idental , consequent ia l or otherwise.
property; lim
other in , a unauthor ized use of the sofing herein
sly providws a an
software l icense agreement. Except as pl iers do not grant any express or impl ie
software. can Technology Corp. in R.O.C and\or other
Microsoft Corp. Moonl ight is registered stered trademark
naScan is ies. Microso
ark of Dyademark
wners.
e furnished for informational use only. Revisions are will be incorporated in later editions. Improvements or
y be made at any time and are subject to change without e by DynaScan. This manual could include mistyping or or liability for any errors or inaccuracies that may
is l imi ted to the cost
Spperiohanges
nd should not be con mitmen
t be l iable for : y defect in the product, damages based up, loss of t ime, loss of prof i ts , loe with business relat ionships, or
Damages to other aused
3. Any c la im against the customer by any other party. Copyright © 2007 DynaScan Technology Corp. 28
Ver.1 DS1508 Quick Start Guide
3.6 Disposal Notices
applia
w
Do not dispose of electrical appliances as unsorted municipal waste,
use separate collection facilities. Contact your local government for
information regarding the collection systems available. If electrical
nces are disposed of in landfills or dumps, hazardous substances
can leak into the groundwater and get into the food chain, damaging
your health and well-being. When replacing old appliances with ne
one, the retailer is legally obligated to take back your old appliances for
disposal at least for free of charge.
29
Copyright © 2007 DynaScan Technology Corp.
MEMO