DT9 manual.pdf
-
Upload
rajeevagrawal -
Category
Documents
-
view
1.403 -
download
240
Transcript of DT9 manual.pdf
-
7/23/2019 DT9 manual.pdf
1/458
Product User Manual
for the
DT_9 Microprocessor Controland Variable Frequency Drive
Feeder Conversion
for
TENUGHAT VIDYUT NIGAM LIMITED
Customer:Apex Industrials
Purchase Order No.:AI/3133/13
Stock Redler India Private Limited Job No: 12720000
Stock Redler India Private Limited WBS No: VK/9113000317
Revis ion 0 - November 2013
Stock Redler India Private Limited. # 3(Old No. 18 & 23), 3rd Main, 1st Phase, Peenya Indusrial Area, Bangalore 560058, INDIA.(080) 30403705/706/707Telefax (080) 30403708
-
7/23/2019 DT9 manual.pdf
2/458
PREPARED & CHECKED REVIEWED (QA & QC) REVIEWED (Service) APPROVED
NAME SIGN DATE NAME SIGN DATE NAME SIGN DATE NAME SIGN DATE
Mechanical
DT_9 Microprocessor Control and Variable Frequency Drive Feeder Conversion
ForTENUGHAT VIDYUT NIGAM LIMITED (2 X 210 MW- Unit-2)
OWNER: TENUGHAT VIDYUT NIGAM LIMITED
(A Govt. of Jharkhand undertaking)
CUSTOMER: Apex Industrials
MANUFACTURER:STOCK REDLER INDIA PRIVATE LIMITED
P.O NO. : AI/3133/13 SRIPL JOB NO.: 1272
DOCUMENT TITLE: O & M MANUAL
SRIPLs Document No. 1272-0000 REV: 0
-
7/23/2019 DT9 manual.pdf
3/458
THIS PAGE INTENTIONALLY LEFT BLANK
-
7/23/2019 DT9 manual.pdf
4/458
Stock Redler India Private Limited
November 20131272-0000 Revision 0
1.0 Installation
How to Use this Manual
This equipment manual is divided into sections which separate the material according to its principal use atthe site.
Section 1.0, for use by the equipment installers, covers receiving inspection, storage instructions, storagemaintenance procedures required, if any, and equipment installation procedures.
Section 2.0, oriented to the operations personnel, contains a system component description of the majoritems of equipment supplied, an initial start-up sequence, and procedures for typical operation. Themaintenance staff, contains an inspection schedule, lubrication information, adjustment and calibrationprocedures, and any necessary troubleshooting guides.
Sections 3.0 through 5.0 contain the schematic and connection diagrams, assembly drawings, and partslists. For ease in locating specific drawings, as well as to bring together all drawings of a similar nature,Section 3.0 contains all the drawings certified for the specific project; Section 4.0 contains all mechanicaldrawings; and Section 5.0 contains electrical and electronics drawings. The drawings within each sectionare arranged in the section index in alphanumerical order except that supportive drawings, such as partslists and schematics, are indented and listed immediately beneath the related assembly drawing. To the leftof the drawing titles, the Stock Equipment Company part numbers are listed to specify the particularassembly supplied from a tabulated drawing. The drawings themselves are then arranged exclusively inalphanumeric order following the section index.
Section 6.0 contains vendor bulletins with specific adjustment, calibration, or service information.
Section 7.0 and following are included when necessary to present optional equipment supplied andrecommended spare parts. These sections are self-contained and are each arranged according to theorganizing principles employed in Sections 1.0 and 2.0 above, with a section index followed by theoperation and maintenance text and relevant drawings.
To keep the manual current, revision packages may be supplied for it as necessary. A Record Of Changes
form is provided in front of Section 1.0 to record these revisions as they are received and processed. It isrecommended that the instruction sheet from each revision package be filed behind the record of changesfor future reference.
Note
The drawings and p arts l is ts incorporated in this manual are correct for the
equipment sup pl ied. The t it le block descr ipt ive inform at ion may no t always agree
with the inform at ion provided in the or iginal propo sal or contract , but the drawing
con tents are correct for the equipment sup pl ied.
Note
This equipment manual is designed to s upp lement, not replace, the or iginal
equipment manual suppl ied with the feeder. I t deals only with addi t ional
considerat ions pertaining to the weighing system electronics and feeder
microprocessor contro ls .
-
7/23/2019 DT9 manual.pdf
5/458
INTRODUCTIONStock Redler India Private Limited
November 20131272-0000 Revision 0
Proprietary Note
The informat ion in this m anual , including technical data and co pies of drawings,
embod ies informat ion prop r ietary to Stock Equipm ent Company. This manu al is
provid ed to the user of equipm ent purchased from Stock Equipment Company for
use only in operat ion or maintenance of such equipm ent. Such inform at ion in this
manual is not to be us ed, disclosed, copied, reproduced in w hole or part for any us e
oth er than that indicated above, or for any oth er purpos e detr imental to the interests
of Stock Equipm ent Comp any. Patents own ed by Stock Equipment Company have
been issued or are pending on some of the informat ion in this m anual . Any
unautho rized use of this sub ject matter of such patents is a violation of such patents
and is proh ibi ted by law.
Electrostatic Sensitive Devices
Caution
The electronic controls contain ESD (Electrostat ic Discharge) sensi t ive parts and
assembl ies that can b e damaged by stat ic electr ic i ty . The fol lowing stat ic contro l
precaut ions are required when test ing, servic ing, or repair ing the
electronic assembl ies.
1. Disconnect power at the main disconnect switch or circuit breaker.
2. Only qualified personnel are permitted to perform and install the electronic controls.
3. Wear a wrist type grounding strap that is grounded to the control cabinet chassis.
4. When replacing the electronic circuit board, do not remove the board from the static shielding bagit came in until you are ready to install the board.
5. When removing any electronic circuit board, immediately place it in a static shielding bag.
6. Stock Equipment Company advises that all printed circuit boards should be returned to the factoryfor repair since our technicians are trained to work with electrostatic sensitive components.
Note
I f you are not fami l iar wi th stat ic control procedu res, before replacing electronic
com pon ents, refer to US Department of Defense DODHDBK -263, Electrost atic
Discharge Control Handbook for protect ion of electronic parts, assembl ies,
and equipm ent.
7. Contact Stock Equipment Companys Parts Department for a returns good authorization numberto facilitate the return of an electronic circuit board. Boards should be shipped in static shielding typebags. If packing materials are used, they should be static-dissipative material.
-
7/23/2019 DT9 manual.pdf
6/458
Stock Redler India Private Limited
November 20131272-0000 Revision 0
1.0 Installation
Table of Contents
PRODUCT USER MANUAL FOR THE DT_9 MICROPROCESSOR CONTROLAND VARIABLE FREQUENCY DRIVE FEEDER CONVERSION
Manual Content
Section 1.0 Installation
Section 2.0 DT_9Operation & Maintenance
Section 3.0 Certified Drawings
Section 4.0 Mechanical Drawings and Parts Lists
Section 5.0 Electrical/Electronic Drawings and Parts Lists
Section 6.0 Vendor Information
Section 7.0 Recommended Spare Parts
-
7/23/2019 DT9 manual.pdf
7/458
INTRODUCTIONStock Redler India Private Limited
November 20131272-0000 Revision 0
Notice
Revised reference material , written text and d rawings may be furnished as required
to up date the informat ion c ontained within this m anual . When revis ions to the
con tent of this m anual are submit ted, ut i lize the Record o f Changes form p rovided
to reco rd al l revisions. Specif ic instruc tions may be provided in the Revision Packet
for recording and insert ing al l changes affect ing th is manu al .
Record of Changes
ChangeNumber
DateEntered
Description of Changes Signature
-
7/23/2019 DT9 manual.pdf
8/458
Stock Redler India Private Limited1.0 Installation
1-1November 20131272-0000 Revision 0
1.0 Installation
Section Index
Topic
1.1 RECEIVING INSPECTION1.2 STORAGE PROCEDURES1.3 SCOPE OF CONVERSION1.4 DT_9 MICROPROCESSOR CONTROL CABINET INSTALLATION1.5 VFD CONVERSION KIT INSTALLATION1.6 ELECTRICAL CONVERSION KIT INSTALLATION
-
7/23/2019 DT9 manual.pdf
9/458
2.0 DT_9 Operation and MaintenanceStock Redler India Private Limited
1-2 November 20131272-0000 Revision 0
1.1 RECEIVING INSPECTION
Upon delivery, inspect the equipment for shortages or evidence of physical damage and make a report to theindependent carrier. Also, notify the Contracts Department of Stock Redler India Pvt. Ltd., to arrange for
the shipment of replacement parts.
1.2 STORAGE PROCEDURES
Prior to shipment from the factory, provisions have been made to protect the equipment in the event thatprolonged storage is required at the job site. These storage procedures are provided as recommendationsto
aid in maintaining the equipment in a warrantable and ready condition.
1.2.1 Storage areas shall be periodically inspected to ensure cleanliness. Discarded packaging and trashshall be removed. Access shall be limited to authorized personnel. Upon placing an item in storage and priorto its removal, the packaging and protective covers should be visually inspected to
ensure that all closures are intact. Any defects in the packaging may be repaired, after insuring that thepackaged material is intact and undamaged, using the original method of packaging. Surface preservatives
may be reapplied or touched up as required.
1.2.2 Equipment is to be stored in such a manner as to provide ready access for inspection and
maintenance with a minimum of handling. Items should be positioned so that any markings or labelings canbe easily identified without excessive handling. Shipping documents are attached to the outside of each crate
to identify the equipment contained inside.
1.2.3 All feeders with electronic enclosures mounted to them must be stored in a heated, ventilatedbuilding where ambient temperatures may be controlled between 5C minimum and 50C maximum.Control enclosure access doors must be tightly closed to engage the sealing gaskets.
1.3 SCOPE OF CONVERSION
1.3.1 The conversion consists of the following:
a. S11154 Remote Power Cabinet With DT_9 Microprocessor assembly
b. S11160 Feeder Integral Cabinet Assembly
c. D43566 VFD Motor 7.5HP Upgrade Kit with Dual Tacho
d. Motor , Loadcell And Calibration Field Cable
Note
System instal lation, schematic, and c onnect ion drawings are provided in Sect ion3.0, Certi f ied Drawing s. Assembly drawings and parts l is ts are provided in Sect ion4.0, Mechanic al Drawing s and Parts Lists and Section 5 .0, Electr ical/Electron icDrawings and Parts Lists.
-
7/23/2019 DT9 manual.pdf
10/458
Stock Redler India Private Limited1.0 Installation
1-3November 20131272-0000 Revision 0
Important
Before perform ing any work inside the feeder, de-energize the feeder by locking the
main circui t breaker or disco nnect swi tch in th e OFF posi t ion.
Important
Safety c onsiderat ions require that electr ical apparatus and enclos ures be so l idly
connected to safety groun d.
1.4 DT_9 MICROPROCESSOR CONTROL CABINET INSTALLATION
Note
System instal lation, schematic, and c onnect ion drawings are provid ed in Sect ion3.0, Certi f ied Drawing s. Assembly drawings and parts l is ts are provided in Sect ion4.0, Mechanic al Drawin gs and Parts L ists and Section 5.0, Electr ical/ElectronicDrawings and Parts Lists.
1.4.1 Close the inlet valve above the feeder and empty the belt.
1.4.2 De-energize the feeder and close the seal air supply if the feeder is so equipped.
1.4.3 If provided, close the feeder discharge valve.
1.4.4 Open all feeder side and end access doors.
1.4.5 Refer to Drawing S11154 and the drawings in Section 3.0, Certified Drawings. Mount the DT_9
microprocessor cabinet assembly onto the feeder by following the instructions provided on
the drawings.
Important
Do no t energize the feeder or the pow er to the contro l cabinets unti l a Stock service
engin eer is p resent. If a service engineer is not present when the feeder or the power
to the con trol cabinets are energized, damage to the equipment, injury o r loss of l i fe
may occu r.
-
7/23/2019 DT9 manual.pdf
11/458
2.0 DT_9 Operation and MaintenanceStock Redler India Private Limited
1-4 November 20131272-0000 Revision 0
Note
Electr ical control enclo sures must b e latched and sealed at all t imes unless
immediate access to them is required, both as a safety measure and to prevent
mois ture damage to components .
1.5 VFD CONVERSION KIT INSTALLATION
1.5.1 Refer to Drawing D43566. Install the VFD conversion kit by following the instructions provided on
the drawing.
1.5.2 Refer to Section 2.0 DT_9 Operation and Maintenance for information on programming and
calibration.
1.6 ELECTRICAL CONVERSION KIT INSTALLATION
Caution
The electronic contro ls co ntain ESD (Electrostatic Discharge) sensi t ive parts and
assembl ies that can be damaged by s tat ic electr ic i ty . The fol lowing s tat ic co ntrol
precaut ions are required when test ing, servic ing, or repair ing the
electronic assembl ies.
Disconnect power at the main disconnect switch or circuit breaker.
Only qualified personnel are permitted to perform and install the electronic controls.
Wear a wrist type grounding strap that is grounded to the control cabinet chassis
When replacing the electronic circuit board, do not remove the board from the static shielding bag it came inuntil you are ready to install the board
Stock Equipment Company advises that all printed circuit boards should be returned to the factory for repairsince our technicians are trained to work with electrostatic sensitive components.
Note
Electr ical contro l enclosures m ust b e latched and sealed at al l t imes u nless
immediate access to them is required, both as a safety measure and to prevent
mois ture damage to components .
-
7/23/2019 DT9 manual.pdf
12/458
Stock Redler India Private Limited1.0 Installation
1-5November 20131272-0000 Revision 0
Note
Befo re instal ling electronics cards, al l f ield w ir ing for the feeder control system m ust
be checked and ver i f ied. Imp roper wir ing may resul t in s evere damage to the
electronics cards when p ower is appl ied.
1.6.1 Refer the drawings in Section 3.0, Certified Drawings and Section 5.0, Electrical/Electronic
Drawings and Parts Lists.
1.6.2 Remove the new electronics cards from their individual packages and install them into the
microprocessor assembly by following the instructions provided on the drawings.
1.6.3 Refer to Section 2.0, D T _ 9 Operation and Maintenance for programming and
calibration information.
-
7/23/2019 DT9 manual.pdf
13/458
2.0 DT_9 Operation and MaintenanceStock Redler India Private Limited
1-6 November 20131272-0000 Revision 0
THIS PAGE INTENTIONALLY LEFT BLANK
-
7/23/2019 DT9 manual.pdf
14/458
Stock Redler India Private Limited2.0 DT_9 Operation and Maintenance
November 20131272-0000 Revision 0
2.0 DT_9 Operation and Maintaenance
DISOCONT
Tersus (DT-9) Weighfeeder VCFInstruction Manual
BV-H6411 GB
-
7/23/2019 DT9 manual.pdf
15/458
2.0 DT_9 Operation and MaintenanceStock Redler India Private Limited
1-8 November 20131272-0000 Revision 0
PASS - A service you can count on. Fast, comprehensive and anywhere in the world.
Quality and reliability are the cornerstones of our companys philosophy. That is why we consider a com-
prehensive service concept simply par for the course, from strict quality control, installation and commis-
sioning through to seamless support across the entire life cycle of our products.
With over 30 service stations and over 180 service specialists, you can count on us to be there whenever
and wherever you need us.
During business hours, our service specialists from all business areas are ready to analyze problems andfind the reasons for failures. You can find the Schenck Process location nearest to you on our website
www.schenckprocess.com .
Are you looking for individual and tailor-made service solutions? Then our modular PASS service system is
just right for you. It includes the entire range of services from simple inspections all the way down to a com-
plete service program. Further information can be found atwww.schenckprocess.com.
Service:
Quality and reliability form the basis for our corporate philosophy all over the world.
In House Support (Monday through Friday from at least 8 oclock to 5 p.m. CST). Service specialists are
available for technical assistance to answer your questions or assist you in trouble shooting.
STOCK EQUIPMENT COMPANY
16490 Chillicothe Rd.
Chagrin Falls, OH 44023 , USA
Phone: +1 440-543-6000
Fax: +1 440-543-6839
e-mail address:[email protected]
24 hour Emergency Support
Are you experiencing a failure or problem outside normal office hours? You can reach our service techni-
cian at any time outside of our office hours for after hour emergency support.
Phone: +1 800-628-3347 (Please listen closely to menu for after hours support.)
by STOCK EQUIPMENT COMPANY
A subsidiary of Schenck Process Group, Germany (www.schenckprocess.com)
All rights reserved. Any reproduction of this documentation, regardless of method, without prior permission
by STOCK EQUIPMENT in writing, even by excerpt, is prohibited. Subject to change without prior notice.
Note: The original manual is in English
(origin: 9007199363029899 V2)
http://www.schenckprocess.com/http://www.schenckprocess.com/http://www.schenckprocess.com/mailto:[email protected]:[email protected]://www.schenckprocess.com/http://www.schenckprocess.com/ -
7/23/2019 DT9 manual.pdf
16/458
Table of Contents
DISOCONT Tersus (DT-9) Weighfeeder VCF, Instruction Manual Schenck Process GroupNovember 2013
1272-0000 Revision 0
BV-H6411GB, 1221
- i -
Stock Redler India Private Limited
Table of Contents
1 About This Manual...................................................................................................................................... 1
2 Safety notes................................................................................................................................................ 3
2.1 Signal Words ................................................................................................................................................52.1.1 Signal Words for Safety Warnings .......................................................................................................52.1.2 Signal Words for Application Notes .....................................................................................................6
2.2 Five Safety Rules of Electrical Engineering .................................................................................................62.3 Damaged / Defective Electrical Components ...............................................................................................7
3 Overview .................................................................................................................................................... 9
3.1 What is the DISOCONT Tersus/DT-9? .......................................................................................................93.2 Definitions ...................................................................................................................................................103.3 Measuring Principle ....................................................................................................................................103.4 Operating Modes - Remote ........................................................................................................................12 3.4.1 Gravimetric .........................................................................................................................................123.4.2 Volumetric ..........................................................................................................................................123.4.3 Volumetric Control..............................................................................................................................12
3.5 Operating ModesOFF/Maintenance .......................................................................................................12
4 DT-9 Setup............................................................................................................................................... 15
4.1 Setup Notes ...............................................................................................................................................154.2 Startup and Functional Check ....................................................................................................................16
4.3 Setup Parameters ......................................................................................................................................174.3.1 Commonly Changed Parameters.......................................................................................................17
4.4 Calibration ..................................................................................................................................................204.4.1 Performing Calibrations......................................................................................................................204.4.2 Weigh Roller Adjustment ...................................................................................................................214.4.3 Basic (CAL 1) ................................................................ ....................................................................224.4.4 Span (CAL 2) ....................................................................................................................................234.4.5 TC: Span Calibration .........................................................................................................................254.4.6 LB: Pulses per Belt ............................................................................................................................264.4.7 TA: Tare .............................................................................................................................................26
4.5 Analog Trim Function .................................................................................................................................274.6 Belt Monitoring............................................................................................................................................284.6.1 Belt Drift Monitoring............................................................................................................................28
4.6.2 Belt Influence Compensation (BIC)....................................................................................................304.6.3 Belt Slippage Monitoring ....................................................................................................................30
4.6.3.1 Monitoring Standstill after Startup ......................................................................................................304.6.3.2 Belt Slippage with Belt Marking .........................................................................................................304.6.3.3 Two-Sensor Belt Slippage Monitoring................................................................................................31
5 Operating and Control Access .................................................................................................................. 33
5.1 Connection between a VHM Operating Panel and a Scales Controller (VCU) ..........................................335.1.1 Connection via Ethernet Cable ..........................................................................................................34
-
7/23/2019 DT9 manual.pdf
17/458
Table of Contents
BV-H6411GB, 1221
- 10 -
DISOCONT Tersus (DT-9) Weighfeeder VCF, Instruction Manual Schenck Process GrouNovember 201
1272-0000 Revision 0
Stock Redler India Private Limited
5.1.2 Connection via Bluetooth ...................................................................................................................345.1.3 Connection via RS485 .......................................................................................................................34
5.2 Connecting a PC with EasyServe to a Scales Controller (VCU) ................................................................355.2.1 Connection via Ethernet.....................................................................................................................35
5.2.2 Connection via RS-232 ......................................................................................................................355.2.3 Connection via WLAN........................................................................................................................35 5.2.4 Connection via Bluetooth ...................................................................................................................36
5.3 Connection between a Web Browser and a VCU Scales Controller ..........................................................365.4 Web Server in the Scales Controller VCU................................ ..................................................................37
6 Operation Using the Touch Screen HMI.................................................................................................... 39
6.1 Initial Configuration ....................................................................................................................................396.1.1 The 'Network' Screen ........................................................................................................................39 6.1.2 The 'Display Settings' Screen ...........................................................................................................40 6.1.3 The 'Feeder' Screen ..........................................................................................................................40 6.1.4 The 'Configuration' Screen ................................................................................................................40 6.1.5 The 'Communication' Screen ............................................................................................................40
6.1.6 The 'Calibration' Screen ....................................................................................................................40 6.1.7 Exiting HMI Configuration .................................................................................................................40
6.2 Display Functions ......................................................................................................................................406.2.1 The 'Home' Screen ............................................................................................................................40
6.2.1.1 Operating the HMI in 'Off/Maintenance' Mode...................................................................................41 6.2.1.2 Operating the HMI in 'Remote' Mode.................................................................................................41
6.2.2 The 'Trend' Screen ............................................................................................................................41 6.2.3 The 'Values' Screen ..........................................................................................................................41 6.2.4 The 'Setup' Screen ............................................................................................................................42
6.2.4.1 Data Log Values.................................................................................................................................42 6.2.4.2 Event Log Values ..............................................................................................................................42 6.2.4.3 Parameter Log Values ......................................................................................................................42 6.2.4.4 Parameter Setup ...............................................................................................................................42 6.2.4.5 Trimming the Analog Inputs and Outputs .........................................................................................43 6.2.4.6 Restoring the Factory Default Settings .............................................................................................44 6.2.4.7 Simulation Mode ...............................................................................................................................44 6.2.4.8 Calibrating the Feeder .......................................................................................................................44 6.2.4.9 Setting the Current Time and Date ...................................................................................................45
6.3 Typical Operating Procedures ...................................................................................................................45
7 Operation Using the 196NT Display .......................................................................................................... 47
8 Operation Using EasyServe...................................................................................................................... 49
8.1 Program EasyServe VPC 20150 ................................................................................................................498.2 Minimum System Requirements ................................................................................................................498.3 Installation...................................................................................................................................................498.4 Start Program and Connect to Feeder .......................................................................................................49
8.4.1 Connecting to Feeder.........................................................................................................................50 8.4.2 Access to Feeder Commands and Parameters.................................................................................51
8.5 Parameter Set.............................................................................................................................................518.5.1 .PAR Files ..........................................................................................................................................52 8.5.2 Read/change Parameters ..................................................................................................................528.5.3 Loading Custom Default Parameters.................................................................................................52 8.5.4 Loading Factory Default Parameters .................................................................................................53
-
7/23/2019 DT9 manual.pdf
18/458
Table of Contents
DISOCONT Tersus (DT-9) Weighfeeder VCF, Instruction Manual Schenck Process GroupNovember 2013
1272-0000 Revision 0
BV-H6411GB, 1221
- 3 -
Stock Redler India Private Limited
8.5.5 Expert Mode.......................................................................................................................................53 8.5.6 Print Parameters ................................................................................................................................53
8.6 Operating the Feeder .................................................................................................................................548.6.1 Scale Operation Screens ...................................................................................................................54
8.6.2 Events ................................................................................................................................................54 8.6.3 Calibration ..........................................................................................................................................548.6.4 Service Values ...................................................................................................................................54 8.6.5 Trends ................................................................................................................................................558.6.6 Setting Time .......................................................................................................................................568.6.7 Options...............................................................................................................................................56
9 Testing .................................................................................................................................................... 57
9.1 Calibration Weight Test ..............................................................................................................................579.2 Chain Test ..................................................................................................................................................579.3 Material Test ...............................................................................................................................................58
10 Parameters............................................................................................................................................... 59
10.1 General Information ....................................................................................................................................5910.2 DT-9 Parameter List ................................................................................................................................ ...65
10.2.1 Parameter Overview ..........................................................................................................................66 10.2.2 Parameter Details ..............................................................................................................................82
10.2.2.1 Parameter Block 01 - Hardware Modules..........................................................................................82 10.2.2.2 Parameter Block 02 - Feeder Definition.............................................................................................84 10.2.2.3 Parameter Block 03 - Control Sources ..............................................................................................91 10.2.2.4 Parameter Block 04 - Rated Data......................................................................................................97 10.2.2.5 Parameter Block 05 - Feeder control...............................................................................................100 10.2.2.6 Parameter Block 06 - Feeder Monitoring.........................................................................................101 10.2.2.7 Parameter Block 07 - Belt Monitoring ..............................................................................................10810.2.2.8 Parameter Block 08 - Filters.............................................................................................................113 10.2.2.9 Parameter Block 09 - Limit Values...................................................................................................114
10.2.2.10Parameter Block 10 - Calibration Data ............................................................................................118 10.2.2.11Parameter Block 11 - Rate controller...............................................................................................121 10.2.2.12Parameter Block 12 - Moisture.........................................................................................................125 10.2.2.13Parameter Block 13 - Cleanout control............................................................................................128 10.2.2.14Parameter Block 14 - Analog Outputs .............................................................................................130 10.2.2.15Parameter Block 15 - Digital Inputs .................................................................................................134 10.2.2.16Parameter Block 16 - Digital Outputs...............................................................................................143 10.2.2.17Parameter Block 17 - Analog calibration..........................................................................................150 10.2.2.18Parameter Block 18 - 2-Sensor Slip.................................................................................................154 10.2.2.19Parameter Block 19 - Maintenance interval.....................................................................................156 10.2.2.20Parameter Block 20 - Data Logging.................................................................................................157 10.2.2.21Parameter Block 21 - Communication EasyServe...........................................................................159 10.2.2.22Parameter Block 22 - Communication Fieldbus...............................................................................160
10.2.2.23Parameter Block 23 - Ethernet.........................................................................................................165 10.2.2.24Parameter Block 24 - PLC Outputs..................................................................................................166 10.2.2.25Parameter Block 25 - Fixed mode configuration..............................................................................168 10.2.2.26Parameter Block 26 - FCB analog outputs ......................................................................................172 10.2.2.27Parameter Block 27 - FCB digital outputs........................................................................................177 10.2.2.28Parameter Block 28 - Configuration HMI Values .............................................................................180
11 Event (Error) Messages ...........................................................................................................................183
-
7/23/2019 DT9 manual.pdf
19/458
Table of Contents
BV-H6411GB, 1221
- 4 -
DISOCONT Tersus (DT-9) Weighfeeder VCF, Instruction Manual Schenck Process GrouNovember 201
1272-0000 Revision 0
Stock Redler India Private Limited
11.1 Events Details...........................................................................................................................................184
11.1.1 Event Group: Calibration..................................................................................................................184 11.1.2 Event Group: Controller ...................................................................................................................185 11.1.3 Event Group: Electrical System .......................................................................................................185
11.1.4 Event Group: Interlock .....................................................................................................................186 11.1.5 Event Group: Material Flow..............................................................................................................187 11.1.6 Event Group: MAX ...........................................................................................................................188 11.1.7 Event Group: Mechanic....................................................................................................................190 11.1.8 Event Group: MIN ............................................................................................................................193 11.1.9 Event Group: Sequence Monitoring.................................................................................................194 11.1.10 Event Group: System Message .......................................................................................................197
12 Default I/O Points.....................................................................................................................................199
12.1 Default Digital Inputs ................................................................................................................................19912.2 Default Digital Outputs..............................................................................................................................20012.3 Default Analog I/O ................................................................ ........................... .........................................201
13 Trending Data .........................................................................................................................................203
14 Appendix .................................................................................................................................................207
14.1 Calculating the setpoint ............................................................................................................................20714.2 Switch-on logic..........................................................................................................................................20814.3 Measuring the feed rate (MEASURE) ......................................................................................................210 14.4 Feed rate controller (CTRL).......................................... ........................... ........................... ......................21414.5 Belt slip identification ................................................................................................................................218
14.5.1 Motion monitoring (BMM).................................................................................................................218 14.5.2 2-sensor slip monitoring...................................................................................................................218
14.6 Belt drift and slip identification via mark in the belt.............................................................. .....................22014.7 Monitoring the mechanism ............................................................................. ......................................... .22214.8 Moist correction (MOIST) .........................................................................................................................223
14.9 The procedure for adjusting the frequency output....................................................................................22314.10 PLC Functionality (Optional).....................................................................................................................224
14.10.1 Handling the Function Blocks...........................................................................................................225 14.10.2 Function Blocks for Binary Signals ..................................................................................................225 14.10.3 Function Blocks for Analog Signals .................................................................................................227
14.11 Serial Networks ........................................................................................................................................22914.11.1 Ethernet Hardware...........................................................................................................................230
14.11.1.1EthernetAddressing......... ....................... ...................... ...................... .......................... ...................23114.11.2 RS-485 Hardware ............................................................................................................................233
14.12 Basics of EMC-Compliant Cabling ...........................................................................................................23514.12.1 Thoughts on the Cable Connections................................................................................................236 14.12.2 Screened Cables..............................................................................................................................236 14.12.3 Unscreened Cables..........................................................................................................................236
14.13 Checking the Weight Measurement Instrumentation ...............................................................................236 14.14 Technical Data VCU 20103 ......................................................................................................................237
14.14.1 Dimensions and Position of the Plugs .............................................................................................238 14.14.2 General Technical Data ...................................................................................................................239 14.14.3 Power Supply...................................................................................................................................239 14.14.4 Auxiliary Voltage for External Subscribers.......................................................................................240 14.14.5 Load Cell Input VME0120 ................................................................................................................24014.14.6 Digital Connections ..........................................................................................................................243
-
7/23/2019 DT9 manual.pdf
20/458
Table of Contents
DISOCONT Tersus (DT-9) Weighfeeder VCF, Instruction Manual Schenck Process GroupNovember 2013
1272-0000 Revision 0
BV-H6411GB, 1221
- 5 -
Stock Redler India Private Limited
14.14.6.1Digital inputs.....................................................................................................................................243 14.14.6.2Digital Outputs..................................................................................................................................247
14.14.7 Analog Connections.........................................................................................................................250 14.14.7.1Integrated Analog Input....................................................................................................................250
14.14.7.2Integrated Analog Outputs ...............................................................................................................25014.14.7.3Optional Analog Channels ...............................................................................................................250
14.15 Touchscreen Operating Panel VHM ................................................................................ ........................25214.15.1 General Technical Data ...................................................................................................................253 14.15.2 Power Supply...................................................................................................................................254 14.15.3 Data Interfaces.................................................................................................................................255
14.15.3.1Ethernet............................................................................................................................................255 14.15.3.2Serial Interfaces: ..............................................................................................................................255
14.15.4 Housing Models ...............................................................................................................................256 14.15.4.1Built-In Console Panel Units ............................................................................................................256 14.15.4.2Portable Devices..............................................................................................................................260
14.15.5 Connecting and Commissioning the Operating Panel.....................................................................263 14.15.5.1Connecting the VHM Operating Panel via Ethernet ........................................................................263
14.15.5.2Connection via RS-485 ....................................................................................................................26414.15.5.3Connection via Bluetooth .................................................................................................................265
14.16 Connecting EasyServe .............................................................................................................................26614.17 Prefabricated system cables ....................................................................................................................26614.18 WLAN access point ..................................................................................................................................27014.19 Basics of EMC-Compliant Cabling ...........................................................................................................271
14.19.1 Thoughts on the Cable Connections................................................................................................272 14.19.2 Screened Cables..............................................................................................................................272 14.19.3 Unscreened Cables..........................................................................................................................273
14.20 EC Declaration of Conformity ...................................................................................................................273
Index .......................................................................................................................................................275
-
7/23/2019 DT9 manual.pdf
21/458
-
7/23/2019 DT9 manual.pdf
22/458
About This Manual
DISOCONT Tersus (DT-9) Weighfeeder VCF, Instruction Manual Schenck Process GroupNovember 2013
1272-0000 Revision 0
BV-H6411GB, 1221
- 1 -
1 About This Manual
This instruction manual describes the controller VCU 20103 loaded with software VCF 20170. This type of con-
troller is designed for controlling a weighbelt feeder, especially for feeding coal into a pulverizer. It is usually
used together with an operator panel type VHM.
For easy retrofits in existing installations with STOCK Equipment controller type 196NT a different type of
DISOCONT
Tersus is provided. Please contact STOCK for details on that variant, if needed.
Additional details on the hardware components and the interfaces of the DISOCONT
Tersus system are found
in the system manual BV-H2406 and the electrical schematics provided with the equipment.
For service purposes a PC or notebook with software EasyServe (type VPC 20150) can be connected. For de-
tails on EasyServe besides the information in this manual see instruction manual BV-H2185.
The controller provides optional means for communication via serial fieldbus of various types to the host plant
control. Details on this communication are found in the separate fieldbus interface manual BV-H2418.
Additional copies of these instructions may be ordered from the Parts Department at Stock Equipment
Company, Chagrin Falls, Ohio. Refer to Part No. ATPDT9VCU20103.
Proprietary Note
The information in this manual, including technical data and copies of drawings, contains information that is pro-
prietary to Stock Equipment Company. This manual is provided to the user of equipment purchased from Stock
Equipment Company for use only in operation or maintenance of such equipment. Information in this manual is
not to be used, disclosed, copied, reproduced in whole or part for any use other than that indicated above, or for
any other purpose detrimental to the interests of Stock Equipment Company. Patents owned by Stock Equip-
ment Company have been issued or are pending on some of the information in this manual. Any unauthorized
use of this subject matter of such patents is a violation of such patents and is prohibited by law.
Electrostatic Sensitive Decices
Caution: The electronic controls contain ESD (Electrostatic Discharge) sensitive parts and assemblies that can
be damaged by static electricity. The following static control precautions are required when testing, servicing, or
repairing the electronic assemblies.
1. Disconnect power at the main disconnect switch or circuit breaker.
2. Only qualified personnel are permitted to perform and install the electronic controls.
3. Wear a wrist type grounding strap that is grounded to the control cabinet chassis.
4. When replacing the electronic circuit board. Do not remove the board from the static shielding bag it came inuntil you are ready to install the board.
5. When removing any electronic circuit board, immediately place it in static shielding bag.
6. Stock Equipment Company advises that all printed circuit boards should be returned to the factory for repair
since our technicians are trained to work with electrostatic sensitive components.
-
7/23/2019 DT9 manual.pdf
23/458
About This Manual
BV-H6411GB, 1221
- 2 -
DISOCONT Tersus (DT-9) Weighfeeder VCF, Instruction Manual Schenck Process GrouNovember 201
1272-0000 Revision 0
7. Contact the Stock Equipment Company Parts Department for a returns good authorization number to facili-
tate the return of an electronic circuit board. Returned components should be shipped in static shielding type
bags. If packing materials are used, they should be made of a static dissipative material.
Note: If you are not familiar with static control procedures, before replacing electronic components, refer to USDepartment of Defense DOD - HDBK-263, Electrostatic Discharge Control Handbook for protection of electronic
parts, assemblies, and equipment.
-
7/23/2019 DT9 manual.pdf
24/458
DISOCONT Tersus (DT-9) Weighfeeder VCF, Instruction Manual Schenck Process GroupNovember 2013
1272-0000 Revision 0
BV-H6411GB, 1221
- 3 -
Safety notes
2 Safety notes
To avoid personal injury and equipment damage, follow the safety regulations stated below.
Additionally, you should observe:
Safety hints given in order-specific documentation
Safety hints relating to mechanical components
Instructions and safety tips for parts manufactured by sub-suppliers or that are not part of Schenck Process's
scope of delivery.
When performing installation, commissioning and service work, observe all applicable local regulations.
Intended Application
The measuring system and its connected mechanical components are exclusively designed for weighing and
controlling tasks. Any use other than originally intended is considered inappropriate.
Sources of Risk
If the measuring system has been correctly installed and commissioned, it does not pose any danger during
weigh operations.
Hazards may arise when the system is used for control operations or for transporting weighed goods. Potential
hazards may then arise from e.g. additional devices through which the weighed goods are passed or metered.
Minor risks may arise in these situations if the measuring system is used or operated by untrained personnel.
The measuring system can be part of a more complex plant. The system operating company is fully responsible
for the operating safety of the system.
Personnel
Preparation, assembly, commissioning, operation, maintenance and servicing may only be carried out by quali-
fied personnel.
All persons working on the system are required to observe the safety hints and know the parts of the technical
documentation relevant to their work.
The operating company is responsible for instructing his operators to observe all regulations and instructions
given.
Changing Parameters
The measuring system's functionality is determined by parameters. Only personnel familiar with the device's
mode of operation may alter these parameters (e.g. after training by Schenck Process). Incorrectly set parame-
ters may cause injury or material damage. Furthermore they may also cause considerable disruption to weigh
operations.
-
7/23/2019 DT9 manual.pdf
25/458
BV-H6411GB, 1221
- 4 -
DISOCONT Tersus (DT-9) Weighfeeder VCF, Instruction Manual Schenck Process GrouNovember 201
1272-0000 Revision 0
Safety notes
Password
Passwords safeguard the parameters against unauthorized alteration. The measuring system operating compa-
ny must ensure that the password is handled safely.
Acknowledging Event Messages
Error messages may be acknowledged only after cause of fault has been remedied.
Ensure that any connected peripheral devices are functioning correctly before acknowledging an event. Any
connected control systems in particular must be in safe state.
Service and Maintenance
All warning and instruction signs on the scales must be observed.
The measuring system must be shut down before work is performed on mechanical equipment or peripheral
devices (control systems in particular). Take appropriate action to ensure that the measuring system cannot
be inadvertently restarted.
Before performing work on the electrical equipment, disconnect the power supply.
The devices may be operated only in the provided housings. There is danger of contacting live parts.
Moisture and Humidity
All scales parts, electrical components in particular, must be protected from moisture and humidity when the
housing is opened for e.g. maintenance and service. In other respects the protection classes of the housing must
be observed.
Design Modifications
Unauthorized modifications to the system and/or use of replacement parts not supplied by Schenck Process
voids Schenck Process's liability for any resulting damages. This especially applies to alterations which could
affect the operating safety of the system.
Replacing Components
Spare parts must meet the technical specifications indicated by Schenck Process. To ensure this requirement is
met, only genuine Schenck Process spare parts should be used. When using other spare parts, the warranty will
be void.
-
7/23/2019 DT9 manual.pdf
26/458
DISOCONT Tersus (DT-9) Weighfeeder VCF, Instruction Manual Schenck Process GroupNovember 2013
1272-0000 Revision 0
BV-H6411GB, 1221
- 5 -
Safety notes
2.1 Signal Words
2.1.1 Signal Words for Safety Warnings
Potential dangers will always exist when working with technical devices. Dangers will arise if the machine
is incorrectly installed,
is started up incorrectly,
is operated by untrained personnel or
is repaired by unqualified personnel
The following signal words indicate throughout this manual dangers that may arise when handling this machine:
DANGER
This signal word indicates a danger that can immediately cause the most
severe injuries up to and including death.
Follow all instructions to prevent this from occurring.
WARNING
This signal word indicates a danger that can cause serious injuries up toand including death.
Follow all instructions to prevent this from occurring.
CAUTION
This signal word indicates a danger that can cause slight or medium inju-
ries.
Follow all instructions to prevent this from occurring.
-
7/23/2019 DT9 manual.pdf
27/458
BV-H6411GB, 1221
- 6 -
DISOCONT Tersus (DT-9) Weighfeeder VCF, Instruction Manual Schenck Process GrouNovember 201
1272-0000 Revision 0
Safety notes
2.1.2 Signal Words for Application Notes
Signal words for information on material damages and on the optimal use of the machine
STRICTLY OBSERVE
Signal word used to identify situations in which material or environmental
damage could occur.
Follow all instructions to prevent this from occurring.
HINT
Signal word used to identify information on using the product economi-
cally and at an optimal level of efficiency.
2.2 Five Safety Rules of Electrical Engineering
These fives safety rules must be followed in the order shown before work is begun on electrical systems. Once
the work is finished, they are to be applied in reverse order.
DANGER
Electric shock from live components.
There is a danger of life from an electric shock.
Take all possible precautions to ensure safety before work is begun on live
components. Observe, among other things, the following:
1. Disconnect the components.
2. Secure them against inadvertent restart.
3. Ensure that the components have been de-energized.
4. Above 1 KV: earth and bypass the cables.
5. Cover or shield adjacent, live components.
-
7/23/2019 DT9 manual.pdf
28/458
DISOCONT Tersus (DT-9) Weighfeeder VCF, Instruction Manual Schenck Process GroupNovember 2013
1272-0000 Revision 0
BV-H6411GB, 1221
- 7 -
Safety notes
2.3 Damaged / Defective Electrical Components
DANGER
Live damaged or defective components
There is a danger of life from an electric shock.
Always have qualified personnel ensure that the components are neither
damaged nor defective.
1. Qualified personnel must immediately replace or, if possible, repair dam-
aged or defective electrical components.
-
7/23/2019 DT9 manual.pdf
29/458
-
7/23/2019 DT9 manual.pdf
30/458
Overview
DISOCONT Tersus (DT-9) Weighfeeder VCF, Instruction Manual Schenck Process GroupNovember 2013
1272-0000 Revision 0
BV-H6411GB, 1221
- 9 -
3 Overview
This chapter explains the principle functions of the DISOCONT Tersus system used in conjunction with a Stock
coal feeder.
3.1 What is the DISOCONT Tersus/DT-9?
The DISOCONT Tersus is a versatile family of modular weighing electronics for use with weighing and feeding
systems.
The DISOCONT Tersus performs all weighing and processing functions required for the measuring and feeding
of bulk solids. It is designed for continuous measuring and control tasks as well as discontinuous batching.
Used in conjunction with the specific application software for weighing and feeding tasks, the DISOCONT Tersus
can be used in the following industries:
Power
Steel
Basic Materials
Cement
Food
Chemical.
In connection with the corresponding mechanical equipment, the following systems are supported:
Belt Scales
Weigh Feeders
Solids flow meters (chutes) Solids flow feeders
Loss-in-weight, gain-in-weight feeders
Mass flow meters (Coriolis meters)
Mass flow feeders (Coriolis feeders)
Filling systems.
The Stock DT-9 configuration of the DISOCONT Tersus is a modified version, optimized for feeding coal in pow-
er plant environment. There are two different versions of the DT-9. One is a completely redesigned and updated
version that is used in new installations. The second one uses the same components and software but has been
optimized for use as an upgrade to existing Stock 8085, 196, and 196NT installations. This version uses the
196NT connectors and mounting footprint.
VCU 20103Designed for new installations where backwards compatibility is not required. This version is iden-
tified by the steel mounting frame and screw type electrical connectors. A Touch Screen HMI is always used
when a VCU 20103 is installed.
VCU 20104Designed as a drop in replacement for the 196NT in existing installations. This version is identified
by the brown Amp style electrical connectors. The VCU 20104 can be used with either a Touch Screen HMI or
with an existing 196NT display.
-
7/23/2019 DT9 manual.pdf
31/458
Overview
BV-H6411GB, 1221
- 10 -
DISOCONT Tersus (DT-9) Weighfeeder VCF, Instruction Manual Schenck Process GrouNovember 201
1272-0000 Revision 0
3.2 Definitions
The table below explains some basic terms used in this manual.
Abbreviation Meaning Explanation Unit
I Actual feed
rate
The actual amount of
material delivered per
unit time
Lbs/hr, Lbs/min, USTons/hr, Kg/hr,
Kg/min or Metric Tons/hr
P Feedrate
setpoint
The desired amount of
material delivered per
unit time
Lbs/hr, Lbs/min, USTons/hr, Kg/hr,
Kg/min or Metric Tons/hr
Z Totalized
amount
Weight of material de-
livered since last coun-
ter reset
Lbs, US Tons, Kg or Metric tons
V Belt speed Feeder belt speed Inches/sec, m/sec
Q Belt load Weight of material per
unit of belt length.
Lbs/inch, Kg/m
QB Platform load Lbs, Kg
Y Controller
magnitude
Output signal magnitu-
de
mA
Xd Deviation Difference between the
actual feedrate and the
feedrate setpoint.
%
3.3 Measuring PrincipleThe belt weighing system is designed to continuously weigh the amount of material transported on the feeder
belt. The actual weight of material transported is calculated by multiplying the feeder belt load, in lbs/inch, times
the feeder belt speed. The systems used to measure these two values are described below.
Belt Load
The feeder weight signal is generated by two load cells that support a single weigh roller. Two weigh span rollers
are located on each side of the weigh roller to accurately define the length of belt (and amount of coal) being
supported by the weigh roller.
Since the load cells only support half of the weight on the weigh span (each load cell supports 25 percent of thetotal weight) the effective platform length (Leff) is calculated as:
Leff = Lg / 2
Leff = Effective platform length
Lg = Total platform length
-
7/23/2019 DT9 manual.pdf
32/458
Overview
DISOCONT Tersus (DT-9) Weighfeeder VCF, Instruction Manual Schenck Process GroupNovember 2013
1272-0000 Revision 0
BV-H6411GB, 1221
- 11 -
The microprocessor computes the feeder belt load by repeatedly reading the voltage signal from each load cell
and converting the signal into a digital value (binary number) using an analog to digital (A/D) converter. Each
value is then compared to parameters stored in permanent memory to determine if the signal is within accepta-
ble limits, and if it is, it is stored for use. The same operation is then performed on the other load cell, and the
signals are compared to each other to test their validity. If the signals are determined to be invalid, the feeder is
switched to volumetric operation and the controller uses a simulated belt load calculated from an historical aver-
age stored in memory. If the signals are determined to be valid, the two load cell signals are summed, the tare is
subtracted and the result is multiplied by a scaling factor based on the load cell data specified in P04.01 LC
Characteristic Value and P04.02 LC Rated Capacity to determine the nominal weight of material on the belt. This
nominal value is then multiplied by the three range correction factors (P10.03, P10.04 and P10.05) to determine
the actual weight (QB).
The belt load (Q) is computed from the total weight (QB) as follows:
Q = QB / Leff
Q = Belt load in kg/m
QB = Weight of load on platform in kg
Note: The 196NT parameter 10 Weigh Span Length is the full distance between the two weigh span rollers. The
DT-9 parameter P04.03 Effective Platform Length is half the distance between the two weigh span rollers. For
any given feeder, the value used by the DT-9 should be one half of the value used by the 196NT.
Belt Speed
During normal feeder operation, the belt speed is calculated from the motor RPM rather then being measured
directly. The relation ship between motor speed and belt speed is determined during calibration and is displayed
as P10.02 Pulses per length.
Feedrate Control and Totals
The weigh and speed information is used to calculate the actual feedrate as shown.
Feedrate (I) = Belt load (Q) x Belt Speed (V)
The feeder control accepts a feedrate set point from the source selected using parameter P03.02 Feedrate Set-
point . This signal is compared with a computed feedrate derived from measured weight and speed signals to
generate the system error signal which is used to adjust the speed of the motor. Compensation for system stabil-
ity is provided in the software using parameters P11.01 P-Component KP and P11.02 I-Component TN. These
-
7/23/2019 DT9 manual.pdf
33/458
Overview
BV-H6411GB, 1221
- 12 -
DISOCONT Tersus (DT-9) Weighfeeder VCF, Instruction Manual Schenck Process GrouNovember 201
1272-0000 Revision 0
calculations are repeated periodically and at each iteration, the actual feedrate is multiplied by the time interval
to calculate the totalizer increment. Separate totals are kept for gravimetric and volumetric operation.
3.4 Operating Modes - Remote
The Remote Operating Mode is provided for normal operation, with the feeder feeding coal under control of the
plant control system. The source for the Start/Stop signal is designated by P03.01Feeder Start and the source
for the feedrate setpoint is designated by P03.02 Feedrate Setpoint. Analog feedback signals are generated
based on the entries to parameter block 14 Analog Outputs. Digital feedback signals (relay outputs) are generat-
ed based on the entries to parameter block 16 Digital Outputs.
While in the Remote Operating Mode, the feeder can use one of three systems to generate the required belt
speed set point.
Details for the different modes can be found in the appendix.
3.4.1 Gravimetric
Gravimetric Mode is the normal mode of operation. The feed rate is calculated using the belt speed and the ac-
tual belt load, and is controlled by the feed rate demand signal supplied by the plant control system. Parameter
P03.05 Maximum Feedrate, corresponds to the maximum demand signal and the minimum feed rate is set by
parameter P03.06 Minimum Feedrate. Parameter P02.05 Nominal Flow Rate should always match parameter
P03.05 Maximum Feedrate. The system can be set to produce an error if the demand signal is outside to normal
range.
3.4.2 Volumetric
Volumetric Mode is used when an error is detected in the weighing system. The actual feed rate is calculated
using the belt speed and an assumed belt load based on the average value over the last several hours, and is
controlled by the feed rate demand signal supplied by the plant control system. Parameter P03.05 Maximum
Feedrate, corresponds to the maximum demand signal and the minimum federate is set by parameter P03.06
Minimum Feedrate. Parameter P02.05 Nominal Flow Rate should always match parameter P03.05 Maximum
Feedrate. The system can be set to produce an error if the demand signal is outside to normal range.
3.4.3 Volumetric Control
Volumetric Control Mode is a variation of the gravimetric mode that is used when the feeder weigh system is
working correctly but the material on belt switch indicates that the belt is empty. The displayed feedrate and the
customer feedback signal is still based on the actual material being fed and the gravimetric total is still beingincremented but the belt speed is determined as if the feeder were in volumetric mode. This mode is used to
prevent the feeder from running to maximum belt speed when material flow is lost.
3.5 Operating ModesOFF/Maintenance
The OFF/Maint mode is is provided so that the feeder can be isolated from the plant control system during
startup, calibration and other maintenance operations. In this operating mode, the plant start/stop and demand
-
7/23/2019 DT9 manual.pdf
34/458
Overview
DISOCONT Tersus (DT-9) Weighfeeder VCF, Instruction Manual Schenck Process GroupNovember 2013
1272-0000 Revision 0
BV-H6411GB, 1221
- 13 -
signals are ignored and feedback signals are not generated. The feeder must be in OFF/Maint mode before a
system calibration can be performed. When the feeder is operated in the OFF/Maint mode, the belt speed is set
based on the value of parameter P02.16 Maintenance Speed. This is an open loop signal calculated as a per-
centage of the full scale signal to the motor speed control (see parameters P11.04 Lower Limit, P11.05 Upper
Limit and P01.06 Controller Magnitude Offset).
In OFF/Maint mode belt can be started via the buttons on the VHM, via the Local key on the 196NT keyboard or
a digital input as defined by P15.25 DI: Local Start .
-
7/23/2019 DT9 manual.pdf
35/458
-
7/23/2019 DT9 manual.pdf
36/458
DT-9 Setup
DISOCONT Tersus (DT-9) Weighfeeder VCF, Instruction Manual Schenck Process GroupNovember 2013
1272-0000 Revision 0
BV-H6411GB, 1221
- 15 -
4 DT-9 Setup
This section describes the startup process when a new feeder is installed or when an existing DT-9 is replaced.
CAUTION
Installing the DT-9 in a feeder that uses the Stock Load Cell Amplifier
Installing the DT-9 in a feeder that uses the Stock Load Cell Amplifier will dam-
age the DT-9. The old style Load Cell Amplifier must be replaced with the new
version before the DT-9 can be used.
CAUTIONDO NOT connect a normal Ethernet cable to X96 (red RJ45 connector).
This connector uses normally unused wires in the CAT 5 cable to provide power
to the touch screen display. Failure to follow this warning may result in damage
to the DT-9 or to the attached network device.
HINT
The weigh span is specified using parameter P04.03 Effective Platform
Length.
This parameter is the distance between the weigh roller and either one of theweigh span rollers. This is one-half the value used by the 196NT, which is the
distance between the weigh span rollers.
4.1 Setup Notes
This section is a general description of the feeder setup process. This process can be performed using either
the touch screen HMI or a PC loaded with the EasyServe software. Section Operation Using the Touch
Screen HMI [ 39] describes the Touch Screen HMI and Section Operation Using EasyServe [ 49] de-
scribes EasyServe.
Events (Error conditions) are usually defined using three parameters. The first, which is usually hidden by
default, defines the input signal that initiates the event, the second specifies the delay between the time
when the error is detected and the time when the event is generated, and the third, specifies the type of
event that is generated (A, W1, W2 or IG). In most cases, the Event (error) can be disabled by setting the
type of event to IG.
The DT-9 has 15 digital inputs (DI 1 through DI 15) and 13 digital outputs (DO 1 through DO 13). Each is
assigned to a specific function, and wired to the appropriate external device. These assignments are hidden
and should not be changed. See chapter Default I/O Pointsfor a list of the default assignments.
-
7/23/2019 DT9 manual.pdf
37/458
DT-9 Setup
BV-H6411GB, 1221
- 16 -
DISOCONT Tersus (DT-9) Weighfeeder VCF, Instruction Manual Schenck Process GrouNovember 201
1272-0000 Revision 0
The DT-9 has one analog input (AI 1) and two analog outputs (AO 1 and AO 2). AI 1 is normally used as the
customer demand signal, AO 1 is normally used to control the motor speed control and AO 2 is normally
used as the customer feedback signal. These assignments are hidden and should not be changed.
The DT-9 has four slots for auxiliary analog I/O cards (channels A10-A13). These channels are not normallyused. Contact Stock engineering if special analog I/O signals are required.
4.2 Startup and Functional Check
This procedure verifies that the feeder and its controls are operating properly, simulates feeder trip conditions,
and checks the principal input/output connections.
1. Apply power to the feeder.
2. Insure that the feeder is in OFF/Maint mode and that the touch screen HMI is set to the home screen.
3. Set the feeder parameters as described in section Setup Parameters [17].
4. Interpret event messages, if any, and correct faults.
5. Unbalance the load cells by engaging the calibration weight on one side of the weigh roller. The display
should indicate volumetric mode. Unbalance each load cell in order to check both sides, then remove the
calibration weight(s).
6. Press and maintain the Jog>> button to verify that belt travel is in the in correct direction.
7. Run the feeder in LOCAL mode by pressing the Run>> button. The feeder will operate at the maintenance
speed programmed in P02.16 Maintenance Speed. Check the motor speed for stability.
8. Run the feeder in LOCAL by pressing the Run>> button. Set the Belt Drive Motor (Run Enable) switch to the
STOP position. The feeder should stop and the display should show a IL01 Event: Run Disabled error mes-
sage. Acknowledge the event and return the Belt Drive Motor switch to its normal position.
9. Stop the feeder and deflect the material-on-belt limit switch paddle to simulate a loaded belt. Run the feeder
in the LOCAL mode to verify that the feeder trips. If it does not, check the adjustment of the paddle switch
cams.
10. Check the event display or the event line on EasyServe. They should both show a WM12 Event: Coal on
Beltalarm message with a time stamp. Acknowledge the event and return the coal-on-belt paddle to its nor-
mal position
11. Calibrate the feeder as described in section Calibration [20].
12. Align the analog inputs and outputs as described in section Analog Trim Function [27].
13. Hang the calibration weights. Produce or simulate a feeder start permissive. Check feedrate and feedback
linearity by applying demand signals of 100, 75, 50, and 25 percent. Compare each demand signal applied
to the feedback signal output. Compare the demand feedrate setpoint (service value 4) with the measured
feed rate of the feeder for each signal.
14. Energize the feeder in the REMOTE mode and deflect the discharge pluggage alarm (or touch the discharge
pluggage sensor with a metal rod). After the preset delay in P15.10, the feeder should be de-energized. If
the feeder does not trip, check the adjustment of the cams for the paddle switch or the sensitivity setting of
the sensor according to the procedure in the original equipment manual.
-
7/23/2019 DT9 manual.pdf
38/458
DT-9 Setup
DISOCONT Tersus (DT-9) Weighfeeder VCF, Instruction Manual Schenck Process GroupNovember 2013
1272-0000 Revision 0
BV-H6411GB, 1221
- 17 -
15. Check the event display or the event line on EasyServe. They should both show a WM07 Event: Discharge
Pluggage alarm with a time stamp. Acknowledge the event and return the discharge switch to its original
state.
16. Return the feeder to REMOTE operation.
4.3 Setup Parameters
The microprocessor controller is tailored to specific feeders and customers needs by the setup parameters.
Feeder-specific physical dimensions must be entered as well as user-selectable display modes and set points.
These values are stored in permanent memory and are only entered once. See section Parameters [ 59] for a
complete list and description of the parameters.
Note: In any given application, the majority of the DT-9 parameters are either not used, or fixed by the design of
the feeder and cabinet. These parameters can be viewed using EasyServe in expert mode (default password
7353) but should not be changed.
The controllers will come preprogrammed from Stock Equipment Company but if changes are needed, there aretwo ways to do this:
Using EasyServe Software (See section Parameters [59])
Using the Touch Screen HMI (See Section The 'Setup' Screen [42])
4.3.1 Commonly Changed Parameters
The following is a list of parameters that are commonly changed during startup. Their values should be recordedfor future reference. See section Parameters [ 59] for a complete list and detailed descriptions.
P-No. P-Name Actual
The following parameters set the feedrate associated with a 100 % demand signal (usually 20 mA). They must
always be set to the same value. See project specific documentation for the correct value.
P02.05 Nominal Flow Rate
P03.05 Maximum Feedrate
The following parameter is the belt speed associated with the nominal (maximum) feedrate and the nominal
material density. It is calculated as:
P02.05 Nominal Flow Rate) / (300 X Nom. Density X P04.10 Load cross section
Inputs are in lbs/hour, lbs/cubic ft and square feet. Results are in inches/sec.
P02.06 Nominal Speed
The following parameter sets the minimum feedrate clamp. See project specific documentation for the correct
value.
P03.06 Minimum Feedrate
-
7/23/2019 DT9 manual.pdf
39/458
DT-9 Setup
BV-H6411GB, 1221
- 18 -
DISOCONT Tersus (DT-9) Weighfeeder VCF, Instruction Manual Schenck Process GrouNovember 201
1272-0000 Revision 0
P-No. P-Name Actual
The following parameter selects the text string displayed on the top line of the touch screen HMI.
P02.03 Scale Name
The following parameters select the units and formats that are used to display the various feeder information on
the display.
P02.01 Language
P02.02 Units
P02.07 Display Formats
P02.08 Flow Rate Units
P02.09 Counter 1 Unit
P02.10 Counter 2 Unit
P02.11 Counter 3 Unit
The following parameter selects the demand signal to the motor speed control when the feeder is running in
local mode. It is normally set to 50 %.
P02.16 Maintenance Speed %
The following parameter specifies the length of belt that is supported by the load cells. It must be set to the dis-
tance between the first weigh span roller and the central weigh roller (one half the distance between the weigh
span rollers). See project specific documentation for the correct value.
P04.03 Effective Platform Length
The following parameter specifies the characteristics of the motor tachometer. See project specific documentati-
on for the correct value.
P04.09 Tachometer: Pulses per Rev P/rev
The following parameter specifies the area under the leveling bar. See project specific documentation for the
correct value.
P04.10 Load cross section
P07.02 sets the maximum time between Belt Motion Monitor (BMM) pluses and P07.03 selects the type of event
that is generated when this limit is exceeded. Set P07.03 to IG if a BMM is not installed. See project specific
documentation for the correct values.
P07.02 Belt Motion Monitor Delay s
-
7/23/2019 DT9 manual.pdf
40/458
DT-9 Setup
DISOCONT Tersus (DT-9) Weighfeeder VCF, Instruction Manual Schenck Process GroupNovember 2013
1272-0000 Revision 0
BV-H6411GB, 1221
- 19 -
P-No. P-Name Actual
P07.03 Event: Belt Motion Monitor A / W1 / W2 / IG
The following parameter specifies the distance between the calibration probe bosses. See project specific
documentation for the correct value.
P10.01 Calibration Probe Span
The following parameter specifies the actual value of the calibration weigh. This value is stamped on the weight.
P10.08 Calibration Weight
The following parameters specify the cleanout conveyor duty cycle. Set P13.02 to zero to run the cleanout con-
veyor continuously.
P13.02 CleanOut ON Time Hours
P13.03 CleanOut OFF Time Hours
The following parameters control the Loss of Material on Beltevent. Setting P05.14 to A causes the feeder trip
(stop the feeder) when the coal on belt signal is lost during normal operation. Setting P05.14 to W1 or W2 will
produce a warning. P05.13 sets the delay between the time that the signal is lost and the time that the event is
generated (This is normally set to one second). Set P05.14 to IG to disable this feature.
P15.13 Loss of Flow Trip Delay
P15.14 Event: Loss of material A / W1 / W2 / IG
The following parameters are used to control the Level/Temperature Sensor event. The Level/Temperature
Sensor input is normally connected to either a flow monitor in the downspout or a temperature switch at the
feeder discharge. Setting P15.21 to A causes the feeder trip (stop the feeder) when the coal flow monitor indi-
cates a loss of flow in the downspout. Setting P15.21 to W1 or W2 will produce a warning. P15.20 sets the delay
between the time that the signal is detected and the time that the event is generated. Set P15.20 to 100 lbs for a
quick response. Set P15.21 to IG to disable this feature. See project specific documentation for the correct valu-
e.
P15.20 Level/Temperatur Sensor Delay
P15.21 Event: Coal Flow A / W1 / W2 / IG
The following parameters specify the Ethernet communications address. The default values should not be
changed unless the DT-9 is connected to a local network.
P23.01 IP Addr