DSCR - Manual Programare.pdf

8/16/2019 DSCR - Manual Programare.pdf

http://slidepdf.com/reader/full/dscr-manual-programarepdf 1/12

DSCR RECEIVER Configuration Manual

===============================

Table of Content

TABLE OF CONTENT..................................................................................................................I

INTRODUCTION.......................................................................................................................1

PRODUCT DESCRIPTION.............................................................................................1

TE DSCR !DSC R ECEIVER " IS AN ADAPTER #IC COMMUNICATES #IT DSC ONE #A$ #IRELESS DEVICES

AND

CONNECTS

TEM

TO

AN$

CONTROL

PANEL

USIN%

TE

&RELA$S

OUTPUTS

.....................1PRODUCT FUNCTIONS...............................................................................................1

PRODUCT FEATURES.................................................................................................1

P$SICAL LA$OUT...................................................................................................................'

CONFI%URIN% TE DSCR UNIT...............................................................................................(

PRERE)UISITES.......................................................................................................(

CONFI%URIN% TE UNIT ...........................................................................................*

LEARNIN% PROCEDURE...............................................................................................+

O# TO LEARN A #IRELESS ,E$ FOB .............................................................................+

O# TO LEARN A #IRELESS PIR DETECTOR ....................................................................-

INSERTIN% A TET DESCRIPTION FOR A DEVICE ................................................................-

DELETIN% A DEVICE PROCEDURE ................................................................................./

......................................................................................................................./

......................................................................................................................./

UPLOADIN% CONFI%URATION TO DSCR UNIT ................................................................10

%ENERAL INFORMATION.......................................................................................................11

STANDARD COMPLIANCE......................................................................................................11



CAPTER 1.

Introduction

Product Description

The DSCR (DSC Receiver) is an adapter which communicates with DSC one way wireless devices and connects them to anycontrol panel using the 5 relays outputs.

Product Functions DSC one way wireless devices compatible

Supports up to 1! devices.

"ach device can be assign to any output (relay).

Device to relay association programming through #$RT inter%ace.

Trouble& 'ow battery &Tamper& Supervision indication available via output.

'ocal tamper protect.

System status in%ormation is acuired by the device input. (ot supported in all versions)

Con%igurable output mode.

Time ad*ustable o% momentarily event.

Toggle output mode.

Product Features 5 relay (+#T1, +#T-, +#T, +#T/, and +#T5)

1 input status

1 push button

Tamper protection

0rogrammable microcontroller with internal %lash memory

Device memory is epandable with eternal optional memory. (ot supported in all versions)

- indication led2s (red, green)

#$RT connector D3'4 compatible

67158dc, /!m$ (use 1$ limited power source)

+peration %reuencies9 / :;<, = :;<

Page #1

7112240 Rev A.



Physical Layout

Component Description

Status LEDs

Green ( RX) : %lashes shortly on every incoming message

Red (T>) :?lin@s every second to indicate normal operation

D- LINK connector Serial port that connects to a 0C or laptop %or programming.

Poer supp!" 4nput 1- 8DC

#ntenna RA antenna

$amper Sitc% $ctivates alarm i% cover is removed.

$ermina! &!oc'+utputs 1 , - , , /, 5 (out 5 mar@ed as TR?' on 0C? )

Status 4nput ( currently not in use )

Page #2

7112240 Rev A.



CAPTER '.

Configuring the DSCR nit

Prere!uisites?e%ore con%iguring the DSCR do the %ollowing9

:a@e sure you have the D3lin@ cable

:a@e sure you have installed the D3'4 cable driver in your 0C (Deriver CD included intoD3lin@ cable bo pac@age)

:a@e sure you have the DSCRBCon%igToll application installed in your 0C

Connect the power supply to DSCR power terminal (be noticed o% the polarity power)

8eri%y red led is bli@ing every second

Connect the D3lin@ cable between DSCR module to 0C #S? port

+n 0C , open 9 Startsettingscontrol 0anelsystemhardwaredevice manger portsand ver%iy which com port was open %or D3lin@ cable

ote 19 %or eample, C+: - was assigned %or D3lin@ cable connection

Page #"

7112240 Rev A.



IPR$#N$ N$E

$%e DSCR modu!e must *e connected to t%e PC usin+ a seria! ca*!e *e,ore "ou can run t%econ,i+uration so,tare.

To Run t2 3onfiguration 4oft5ar26

1.Double3clic@ on the icon.

-.Select the correct C+: port number assigned to D3lin@ cable.

.Clic@ the button.

/. $pplication will display on a success%ul connection

8er. !. S version

8er. 1.! ; version

Configuring the nitThis section describes how to con%igure the unit using a local C+: port.

The +utputs (Relays R1, R-, R, R/ and R5) can be programmed to one o% the %ollowing modes9

Page #

7112240 Rev A.



Re!a" ode Description

Not #ctie The relay is disabled

penC!ose 1. i% R1 bo is unchec@ed status, the Relay opens on a detectionevent

-. i% R1 bo has been chec@ed, relay c!osed on a detection event

$o++!e on every incoming message the relay will change its mode state

omentar" The momentary time parameter determines how long the relay will remains inthe new state a%ter every new incoming message

$rou*!e This mode indicates a trouble event %rom any programmed device anddedicated %or all devices ( not relevant %or DSC smo@e detector 6!= model)(Note 9 this mode disables all other modes ) see emples on the net pages( Note9 devices @nown with trouble indication %eature are support )

Lo &atter"This mode indicates a 'ow ?attery event %rom any programmed device anddedicated %or all devices (ote 9 this mode disables all other modes ) seeeemples on the net pages

$amper This mode indicates a Tamper event %rom any programmed device and %romthe receiver either and dedicated %or all devices (ote 9 this mode disables allother modes ) see eemples on the net pages

SuperisionThis mode indicates a loss o% communication Supervision event %rom anyprogrammed device and de%ined %or sending supervision state %or all devices(ote 9 this mode disables all other mode ) see eemples on the net pages

omentar" $ime setting the momentary time period by clic@ing on the parameter value (see picturebelow) and enter new value %rom 1 to -5! sec

Superision $ime setting the Supervision time period by clic@ing on the parameter value (see picturebelow) and enter new value %rom 1 to -5! min.

Important Note /9 a%ter every change&update on the 0C $pplication installer must press on the Setcon,i+uration button below to save and load the con%iguration into the receiver .

Page #$

7112240 Rev A.



"ample o.1 $rou*!e ode has been selected and as a result all the entire R1 column has beencovered with a dar@ color that indicates the relay R1 is dedicated %or trouble events only %or all devices

(ecept DSC smo@e detector 6!= model) and prevents %rom de%ining other modes .

"ample o.- Superision ode has been selected, and as a result o% this all the entire R1 columnhas been covered with a dar@ color that indicates the relay R1 is dedicated %or

supervision events %or all devices only, but this is relevant i% the installer chec@ed thesupervision bo column to enable this %unction.

See below description table o% all %ields and buttons o% the second application part.

Field / Button Description

0 0 Device umber

Page #%

7112240 Rev A.



Field / Button Description

ID Device 4denti%ication , device id can be inserted manually by clic@ing on thespeci%ic value or automatically by learning a device procedure mode

#C$I1E 1. $ctive bo should be chec@ed unchec@ed in order to activate or deactivatea device, -. this bo is chec@ed automatically a%ter learning a device issuccess%ul

NNE Disables the detection event report only by selecting Enone Eoption, but allother events remain in normal operation (low bat. Trouble, tamper,supervision )

R2 3 R/ 3 R4 3 R5 3 R6 +utputs Relays 1 to 5 selectable relays %or di%%erent operation modes.

S7PER1ISIN

Chec@ bo must be chec@ed in order to activate the supervision reportoperation (not relevant %or devices without supervision %unction such aswireless @ey%ob), installer must be aware not to chec@ the supervision bo %ordevices that do not use the supervision %unction

Learn deice *uttonStarts the learning device procdure by clic@ing this button ( learning procdurewill be described on the net pages)

De!ete deice Deletes learned device by clic@ing this button

De!ete a!! deices Deletes all learned devices by clic@ing this button

Set description #sed %or insert a tet description %or each device

Set con,i+uration Saves and sends con%iguration into DSCR unit

Learning procedureTo learn a Device, installer must %irst ensure that the receiver %reuency is compatible with all devices.

'earning the devices is possible by generating an event %rom the devices such as opening a tamper switchF create an eventF or *ust clic@ing on a wireless @ey %ob button

$ device can be learned multiple times and assigned to a di%%erent relay %or a di%%erent %unction.

&o' to learn a 'ireless (ey fobStep 19 select and position on the device 4D number (see the picture below(

Step 2: Press the learn button

The net message appears as soon as the learn button is pressed

Step 9 installer must select wireless @ey %ob button ($R: button %or eample) and press on it while theabove message is running.

Page #)

7112240 Rev A.



The net picture indicates learning procedure has been completed success%ully.

Step /9 installer should select the relays which will operate according @ey %ob buttons

Aor eample, as per above %igure9 @ey %ob !!1 4D9 =/$5D.1 (@ey no. 1) is assigned to R1

ey %ob !!- 4D9 =/$5D.- (@ey no. -) is assigned to R-

Step 59 repeat steps 1 to %or all other @ey %ob buttons

Note 49 Re%er to ote -.

&o' to learn a 'ireless PIR detectorStep 19 select and position on the device 4D number, %or eample location !! has been selected (seethe picture below(

Step - 9 0ress the learn button

The net message appears as soon the learn button is pressed

Step 9 installer must press on the tamper switch while above message is running

The net picture indicates a success%ul learning o% 04R detector procedure

Step /9 select the relays which will operate according to the 04R detector events, R- has beenselected.

Step 59 chec@ the supervision ?o %or 04R detector i% supervision report is reuired

Step =9 repeat steps 1 to 5 %or all others devices

Note 59 Re%er to ote -.

Inserting a Te*t Description for a de+iceStep 19 select and position on the device 4D number, %or eample location !! has been selected

Page #,

7112240 Rev A.



Step -9 0ress the Set Description ?utton

The et window will open

Step 9 4nsert tet description %or a device

Step /9 4n order to save all tet descriptions installer must save them into a %ile

4mportant ote 59 Tet descriptions are not stored into DSCR unit

Step 59 Go to Ailesave con%ig and save it into a %ile

Deleting a de+ice procedureStep 19 select and position on the device 4D number to be deleted

Step -9 0ress the Delete Device button

Step 9 0ress yes or not to con%irm

Page #-

7112240 Rev A.



ote =9 re%er to ote -

ploading configuration to DSCR unit4n order to send con%iguration to DSCR unit

Step 19 0ress the Set Con%iguration button

Step -9 0ress yes to send con%iguration and continue

Page #1.

7112240 Rev A.



CAPTER (.

/eneral infor0ation1o!ta+e input ran+e 6 7 158dc

Current consumption /!m$

$emp. Ran+e (operation) 31!H 7 I55HC

R8 operatin+ ran+e 15!m

peratin+ 8re9uencies /.6-:;<F =.5:;<

Com. port D3'in@, 115.-@bps, bit, no parity, 1 stop bit

Dimentions J!mm 1-mm -=mm

ei+%t 1-!g

Standard Co0pliance

EN 4;; //;-/EN <2;;;-<-4EN 6;24;-5EN 4;2 5=>-2EN <;>6;-2

Ro?S Directie /;;/>6EC

Page #11

7112240 Rev A.

DSCR - Manual Programare.pdf

Documents

Transcript of DSCR - Manual Programare.pdf