DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014...

32
JANUARY/FEBRUARY 2014 www.paperage.com CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market DRYER SECTION PERFORMANCE Five easily applied dryer performance indicators make way for optimal energy efficiency

Transcript of DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014...

Page 1: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

JANUARY/FEBRUARY 2014

www.paperage.com

CONTAINERBOARDCapacity bulge, sluggish demand remain challenges for containerboard market

DRYER SECTION PERFORMANCEFive easily applied dryer performance indicators make way for optimal energy efficiency

Page 2: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

In Tune for Sustainability, Agility and Profitability

HigHligHts • Tissue360° Forum• OpEx Reliability Workshop• Executive Panel

• State of the Industry• Papermaking Sessions• Coating Sessions• Expanded Exhibit Hours

papercon.org

Joining PaperCon:

Jim AbbottFormer Major League

Baseball Pitcher

Dan Malenke President, PKGPRO

Keynote Speakers:

FORUMReliabilityWorkshop

at PaperCon 2014OpEx

Page 3: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

F E AT U R E S

18 Easy-to-Apply Dryer Performance Indicators

The dryer section is a large consumer of energy, but ensuring it is operating efficiently is not difficult. By assessing only a few easily applied “dryer performance indicators”, one can deter-mine whether large improvement opportunity exists.

22 Microbiological Auditing and Control – A New and Powerful Approach to Controlling Problem Organisms

A genetic-based technique used to detect and identify troublesome microbes in paper mills’ fresh water systems has been found to be quick, accurate, and less cumbersome than traditional methods.

26 Keep it Running Smooth To succeed in today’s fiercely competitive market-

place, pulp and paper manufacturers positively, absolutely, require maximum equipment availability and productivity from their machinery, and a disciplined lubrication management program can make this happen.

c o n t e n t sJANUARY/FEBRUARY 2014, Volume 130, Number 1

C O L U M N S

14 Market Grade: Containerboard 2013 wasn’t a bad year for containerboard mills

but results were decidedly mixed. Price increases were enacted on board and corrugated boxes in early 2013 that boosted margins, but underlying box demand was stagnant. 2014 offers hope that improved economic growth can propel box demand to stronger gains, but the impact of new containerboard capacity remains a nagging concern.

16 Heads-Up: Quiet Start in Europe The European paper industry is off to a relatively

quiet start in 2014, and industry observers say the year may continue as such, which may be a good thing.

30 Recycling Matters Continuous commitment to paper recovery for

recycling paper recovery has fostered a dynamic marketplace that allows recovered fiber to find its highest-value use, which helps to encourage even more recycling.

D E P A R T M E N T S

4 Editor’s Note

6 Industry News

12 People

13 Calendar

S E R V I C E S

29 Classified Ads

29 Index of Advertisers

18

3PaperAge    JANUARY/FEBRUARY 2014

Page 4: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

4

By John O’Brien, Managing Editor [email protected]

. . . try, try again. With that in mind, Verso

Paper on January 6 announced that it would

acquire NewPage in a deal valued at $1.4

billion. This will be a very big deal if the two

companies can actually get past the initial

proposal stage. They’ve been down this road

before and it has been a very, very bumpy

ride to say the least.

As some may recall, the on-again, off-again

romance between Verso and NewPage dates

back to 2010 and early-2011. At that time,

private equity owners, Apollo Management

(Verso) and Cerberus (NewPage), were repor-

tedly in talks that most industry observers pre-

sumed were about the combination of North

America’s two largest coated paper producers.

However, many analysts pointed out that the

two papermakers carried much too much debt

for the deal to make financial sense, especially

to certain groups of lienholders.

Nothing, it appeared, but speculation

resulted from those talks, and on September

7, 2011, NewPage filed for creditor protection

under Chapter 11.

As NewPage moved into its tenth month

of reorganization, Verso on July 2, 2012

announced that it had “held discussions with

certain holders of the 11.375% first-lien senior

secured notes of NewPage Corporation in an

effort to achieve a potential business combina-

tion involving Verso and NewPage as part of a

consensual plan of reorganization in NewPage’s

Chapter 11 bankruptcy proceedings.”

How did that proposal go over? Not very

well; not very well at all. Just ten days after the

proposal, an attorney representing holders

of first-lien debt strongly rebuffed the deal in

a letter to Judge Kevin Gross, U.S. Bankruptcy

Court in Delaware. The letter concluded that

(1) Verso’s market position would be greatly

improved if Verso was able to acquire

NewPage’s assets at fire sale prices or if debtors

fail to reorganize; (2) Verso is significantly

threatened by the possibility that NewPage

will successfully reorganize under a stand-

alone plan and emerge from bankruptcy a

stronger, healthier company with a deleveraged

balance sheet; and (3) Verso stands to benefit

from any delays in the debtors emergence

from bankruptcy and can be expected to

oppose all stand-alone plan proposals and any

near-term restructuring.

Over the summer of 2012, the two com-

panies sparred until Verso on Sept. 4 finally

called a halt to its pursuit of NewPage, stating

that “it has decided to cease further discussions

with NewPage Corporation or its creditors

regarding a potential business combination.”

Or maybe not. After a 16-month regroup-

ing period, both parties, it seems, have had a

change of heart and are in agreement to the

structure of a new deal (see page 6) — a very

complicated deal. In a recent presentation by

Verso, “NewPage Operating Company would

be a non-guarantor restricted subsidiary for

Verso’s notes with a standalone capital

structure.”

Moody’s Investor Services explains it

like this, “It is anticipated that following the

acquisition, Verso and NewPage will be run as

separate legal entities with a shared services

agreement.”

Regardless of the complexities, Verso has

hung in there, I’ll grant it that. And although

there remains a lot of people to satisfy, includ-

ing possibly antitrust regulators (Verso and

NewPage would have at least 50% of the

coated freesheet market), perseverance may

be the lynchpin that sees the deal through

this time around. n

If at first you don’t succeed…

JANUARY/FEBRUARY 2014VOLUME 130, NO. 1

EDITOR IN CHIEF Jack O’Brien

PUBLISHER Michael C. O’Brien

MANAGING EDITOR John F. O’Brien, Jr.

CONTRIBUTING EDITOR Harold M. Cody

CONTRIBUTING WRITER David Price

CONTRIBUTING WRITER John Yolton

LAYOUT & DESIGN George H. Dean Co.

SALES OFFICE

20 Schofield Road

Cohasset, MA 02025-1922

Phone: (781) 923-1016

Fax: (781) 923-1389

email: [email protected]

Web Site: www.paperage.com

EDITORIAL OFFICE

42A Country Way

Scituate, MA 02066-3743

Phone: (781) 378-2126

Fax: (781) 923-1389

email: [email protected]

Web Site: www.paperage.com

Copyright ©2014 by O’Brien Publications, Inc. All rights

reserved. PaperAge (ISSN:0031-1081) is published six

times per year with those issues being January/February,

March/April, May/June, July/August, September/October,

November/December by O’Brien Publications, Inc.,

20 Schofield Road, Cohasset, MA 02025-1922.

Periodicals postage paid at Cohasset, MA and additional

mailing offices.

Publication Mail Agreement #40112731.

Canadian Mail distribution information:

Express Messenger International,

P.O. Box 25058, London BRC.

Ontario, Canada N6C 6A8

POSTMASTER: Please send change of addresses to:

PaperAge, 20 Schofield Road, Cohasset, MA 02025-1922.

Subscriptions: PaperAge is mailed without charge in the

U.S. and Canada (upon written request) to qualified

individuals in the pulp, paper, paperboard, and paper

converting industries. To all others there is a subscription

charge of $54.00 in the U.S., $60.00 in Canada, and

$90.00 in all other countries. Single copies may be

purchased for $10.00 each. All payments must be made

in U.S. funds and checks must be drawn from a U.S. bank.

Credit cards are accepted.

Reproduction of by any means of the whole or part of

PaperAge, without written permission, is prohibited.

4 JANUARY/FEBRUARY 2014 PaperAge

editors note

Page 5: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

Thiele Kaolin Company • Sandersville, GA(877) 544-3322 • thielekaolin.com

If you had to choose a kaolinsupplier based on one quality,which would you choose?

o TAILORED SOLUTIONS

o SERVICE

o STABILITY

o LONGEVITY

o GLOBAL REACH

o PRODUCT DEVELOPMENT

The good news is you can have them all with Thiele, a privately held company serving papermakers worldwide since January 1, 1947.

Tailoring kaolin to your needs.

Thiele_Pencil_PaperAge_fp_1 10/21/10 5:03 PM Page 1

Page 6: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

SP Fiber Technologies to Convert Newsprint Machine in Newberg Mill to Lightweight ContainerboardSP Fiber Technologies, LLC (SPFT) announced plans to convert a newsprint machine at the company’s Newberg, Oregon paper mill to produce lightweight containerboard. PM5 ceased production of newsprint on January 15 to allow for necessary process modifications, the company said. The conversion is expected to be completed in the sec-ond quarter of this year. SPFT said that it will continue providing high quality, recycled content newsprint for the west coast market from the mill’s PM6. “This project reflects the strategy to grow our packaging business while remaining a preferred newsprint supplier in the West,” said Allen Byrd, SPFT’s CEO. “Newberg is a solid asset with great people. We are very excited about this expansion of our packaging business in the West.”

Verso Paper and NewPage on Jan. 6 announced a definitive agreement under which Verso will acquire NewPage in a trans-action valued at $1.4 billion.

Upon closing of the deal, the combined company will have sales of approximately $4.5 billion and 11 manufacturing facili-ties located in six states. The transaction, which has been unanimously approved by the boards of directors of both companies, is expected to close in the second half of 2014, subject to regulatory approvals. “The combination of Verso and NewPage will create a stron-ger business that is better positioned to serve our customers and compete in a competitive global marketplace,” said David J. Paterson, Verso’s President and CEO. “We continue to face increased competition from electronic substitution for print and international producers, but as a larger, more efficient organization with a sustainable capital structure, we will be better positioned to compete effectively and deliver solid results despite the industry’s continuing challenges. Furthermore, we believe the transaction provides stakeholders in both companies with meaningful, compelling value,” Paterson said. The combination of the two companies is expected to result in at least $175 million of pre-tax total cost synergies, which are

expected to be achieved during the first 18 months after comple-tion of the transaction. Dave Paterson will lead the combined organization. Under the terms of the deal, NewPage’s equity holders will receive total cash and debt consideration of $900 million, con-sisting of $250 million in cash, most of which will be paid to the stockholders as a special dividend prior to closing and the remainder of which will be paid at closing, and $650 million of new Verso first lien notes to be issued at closing. NewPage’s equity holders also will receive shares of Verso common stock representing 20% (subject to potential adjust-ment up to 25% under certain circumstances) of the outstanding shares as of immediately prior to closing. Certain of NewPage’s stockholders owning a majority of the outstanding shares of NewPage common stock have agreed to vote their shares in favor of the approval of the transaction. Verso will finance the acquisition through $750 million in committed financing, which will be used to pay the cash portion of the merger consideration and to refinance NewPage’s existing $500 million term loan prior to closing. The value of the transaction is $1.4 billion, composed of the cash consideration, the $650 million of new Verso first lien notes, the Verso common stock and the refinancing of NewPage’s $500 million term loan.

NORTH AMERICA

Verso Paper to Acquire NewPage in $1.4 Billion Deal

Fox River Fiber Begins Use of Wastewater Pre-treatment FacilityFox River Fiber announced that it has begun utilizing a $7 million wastewa-ter pre-treatment facility designed to reduce the company’s environmental impact from its pulp manufacturing operations. The De Pere, Wisconsin-based pulp manufacturer utilizes post- consumer fiber as its primary raw material for making high-quality pulp. According to the company, the on-site anaerobic digesting system creates cleaner industrial wastewater prior to releasing it to the Green Bay Metropolitan Sewerage District. Fox River Fiber said that it plans to sell the recovered biolog- ical solids to other anaerobic treatment facilities for use as seed in treatment towers.

6 JANUARY/FEBRUARY 2014 PaperAge

industry news

Page 7: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

NORTH AMERICA

Resolute to Indefinitely Shutdown the Last Paper Machine at Fort Frances Mill

Resolute Forest Products has announced the indefinite shutdown of the last operating paper machine at its mill in Fort Frances, Ontario by the end of January. The measure will, in effect, shut-down the entire mill. Some 150 workers will be impacted by the decision.

Late in November of 2012, Resolute shutdown the kraft mill at Fort Frances, which has an annual production capacity of approximately 200,000 metric tons of market pulp, and PM5, which has an annual capacity of 105,000 metric tons of ground-wood specialty printing papers. According to a CBC news report, Resolute attributed this lat-est shutdown as the result of poor market conditions, although company president Richard Garneau said the paper machine will be kept ready for future operation. In the meantime the company said it is looking for alternative products for its Fort Frances operation, especially related to the pulp mill.

RockTenn Acquires NPG to Expand Retail Innovation and SolutionsRockTenn in early-January acquired NPG, Inc., a leading inde-pendent merchandising displays company. Headquartered in Chattanooga, Tennessee, NPG provides a broad range of display products and services to many of the world’s most recognized retailers. NPG employs approximately 400 co-workers and operates two manufacturing facilities in Chattanooga and one in Las Vegas, Nevada. “NPG’s focus on retailers, their innovative retail solutions and large-format printing capability expands our customer base and significantly improves RockTenn’s ability to provide retail insights, innovation and connectivity to all of our customers,” said Craig Gunckel, executive vice president, RockTenn, and general manager, RockTenn Merchandising Displays. NPG will operate as RockTenn Retail Solutions. Phil Harris, formerly chief executive officer of NPG, has been named vice president and general manager, RockTenn Retail Solutions. Harris will continue to manage the operations along with his current leadership team. “NPG is a strong strategic fit for us that will strengthen our display business,” said Steve Voorhees, RockTenn’s chief execu-tive officer. “I am excited to have the NPG team join RockTenn and look forward to supporting their continued success.”

NPTA Presents 2014 Stanley O. Styles Industry Excellence Award to

Don and Max Clampitt of Clampitt PaperThe National Paper Trade Association

(NPTA) announced the recipients of its

2014 Stanley O. Styles Industry Excellence

Award — NPTA’s highest honor. For the

first time in the award’s 30-year history, it

will be presented to two industry leaders,

Don and Max Clampitt of Clampitt Paper.

“Over the years, there are only a very

few whose names are synonymous with the merchant and

paper business. Clampitt is one of those rare names,” said

Tom Gallager, President of West Linn Paper Company. “Max

Clampitt was a leader in every regard.”

Max Clampitt was born in 1912 in Ruston, Louisiana and

founded Clampitt Paper with his wife, Mary-Nell, in 1941.

“Max Clampitt was a force in the merchant community,”

said James C. Tyrone, EVP of Commercial Operations and

Business Development, NewPage Corporation. “He built a

highly reputable and successful merchant business from the

ground up. Don continued with the same focus on custom-

ers that Max did.”

Don Clampitt began his 34-year career in the paper

industry working in the warehouse of Clampitt Paper during

high school. He returned to the firm after graduating from the

University of New Mexico and since that time has worked in

almost every position in the company. When Max passed

away in 2001, Don stepped into the President and CEO role.

“In a time when paper is too often reduced to a com-

modity, Don still loves to talk about what makes paper,

particularly premium paper, unique,” said Tom O’Connor,

Chairman and Chief Executive Officer of Mohawk. “He

pioneered the establishment of a Creative Center where

designers and printers can come look at samples and talk

about their work. Don is the only CEO of a major paper dis-

tributor I know of who still loves to go out and teach paper

classes for customers and design students.”

In addition to launching the Clampitt Creative Center in

2004, Don has grown the Clampitt brand to include 15 retail

stores and six warehouse locations and expanded to Tulsa,

Albuquerque and Kansas City.

Don Clampitt noted, “My father was the true visionary

behind Clampitt Paper, and I am honored to be considered

with him as a recipient of this award.”

Don Clampitt will accept the Stanley O. Styles Industry

Excellence Award on behalf of himself and Max at the

Paper2014 convention, March 23-25 in New York City.

Don Clampitt

7PaperAge    JANUARY/FEBRUARY 2014

industry news

Page 8: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

NORTH AMERICA

ASPI Recognizes Kapstone’s Paul Duncan with Excellence in Leadership Award

The Association of Suppliers to the Paper Industry (ASPI) has named Paul Duncan as the recipient of its 2014 Excellence in Leadership Award. Duncan serves as mill manager at KapStone Paper and Packaging’s Longview Mill in Longview, Washington, where he is responsible for managing all of the

manufacturing, maintenance and support operations of the mill. “The Longview mill’s turnaround has been an incredible achievement for everyone involved, and Paul Duncan has been a big part of that change,” said ASPI President Carl Howe, vice president sales for Kadant Paperline. “His professionalism, his technical knowledge, and the example he sets for his employees all deserve to be recognized and applauded.” As mill manager, Duncan played a critical role in the recent transformation of the Longview mill, which resulted in a produc-tion increase of 39% between 2007 and 2012. He also played a key role in improving the mill’s safety culture, and was named “Safety Manager of the Year” at the Western Pulp and Paper Workers Conference in 2012. ASPI’s Excellence in Leadership Award honors unique and creative leadership of employees, company and key suppliers through major projects or ongoing relationships. ASPI accepts nominations from its members, and the Board of Directors votes to determine the recipient. Duncan is scheduled to accept the award at the ASPI 2014 Spring Meeting, which will be held February 26-28, 2014 in Sarasota, Florida.

Ahlstrom Completes Sale of Its West Carrollton PlantAhlstrom has sold the converting operations of its West Carrollton plant in Ohio to West Carrollton Parchment and Converting Inc., an Ohio-based family-owned company. The parties have agreed not to disclose the value of the deal. Under the terms of the deal, Ahlstrom sold its vegetable parchment converting assets and related order book to West Carrollton Parchment and Converting. The approximately 70 employees at the plant will transfer to West Carrollton Parchment and Converting. As part of the sale, Ahlstrom and West Carrollton Parchment and Converting will establish a long-term supply agreement for vegetable parchment paper, which is primarily used in food packaging.

Paul Duncan

FPInnovations and Kruger in Joint Project to Build Cellulose Filament Demonstration PlantFPInnovations and Kruger Inc. have announced a joint project to implement the world’s first five ton/day cellulose filament demonstration plant at Kruger’s Trois-Rivieres Paper Mill. The research and innovation project represents investments totaling $43.1 million, including funding from Natural Resources Canada, through the Investments in Forest Industry Transformation (IFIT) Program, as well as a grant from the Quebec Ministry of Natural Resources, a loan from Investissement Quebec, a con-tribution from Kruger Inc. and funds from FPInnovations’ pulp, paper and bioproducts industrial members. “A highly innovative wood-fiber based biomaterial, cellulose filaments (CF) are expected to have an immediate impact on Canada’s forest industry due to their capacity to be integrated into other materials and to their high strength, light weight and flexibility,” FPInnovations said. “CF will be used in a wide range of applications as a lightweight strengthening additive to pro-duce lower cost commercial pulps, papers, packaging, tissues and towels.” According to FPInnovations, the potential initial market for CF as a strength reinforcing agent for traditional pulp and paper products is conservatively estimated at 120,000 tons per year in North America alone. In addition, a similar-sized, non-traditional market is forecast for thermoplastics, reinforced plastics, thermo-sets, adhesives, and non-woven fabric and coatings, representing a total revenue potential of $500 million per year for companies that make use of CF.

INDIA

Andhra Pradesh Paper Mills Changes NameInternational Paper announced that the name of its group

company, The Andhra Pradesh Paper Mills Limited (APPM),

has been changed to International Paper APPM Limited,

effective Dec. 16, 2013.

The company currently operates through two paper

mills at Rajahmundry and Kadiam in Andhra Pradesh under

APPM’s name.

“The new name recognizes the parentage of International

Paper while maintaining the link to the history of the

APPM brand,” explained Michael Amick Jr, President, IP

India and Executive Chairman, International Paper APPM

Limited.

8 JANUARY/FEBRUARY 2014 PaperAge

industry news

Page 9: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

EUROPE

CEPI Director General Teresa Presas to Step Down, Marco Mensink Named Successor

After 10 years at the helm of CEPI, the Brussels-based Confederation of European Paper Industries, Teresa Presas has decided to leave the organization at the end of May this year. In the com-

ing months she will ensure a smooth transition of the leadership of CEPI to her designated successor Marco Mensink, who has already worked with Presas as CEPI’s Deputy Director General for the last two years. Presas commented, “It has been ten years of an enriching experience and of relentless work. In the last years, we have consolidated our organization, successfully defended its interests and laid out our long-term vision for the sector in the CEPI 2050 Roadmap. “The coming years will be about implementation at the different levels, including the progression of the breakthrough concepts that came out of the Two Team project. Therefore, it is a good moment for me to leave the organization and move on to another life. I wish my colleague and successor Marco Mensink every success in the future,” Presas concluded.

Domtar Completes Acquisition of Spain’s Indas Domtar on Jan. 2 closed the acquisition of privately-held Laboratorios Indas, SAU (“Indas”), pursuant to a definitive agree-ment announced on November 19, 2013. Indas is Spain’s largest manufacturer and marketer of branded adult incontinence products, with its IncoPack and Indasec line of products. Domtar acquired all the outstanding capital stock for EUR285 million and the business was expected to have about EUR140 million of debt, net of cash, at closing. Prior to the closing, Domtar explained, “the net debt is expected to be reduced by the collection of approximately EUR25 million of past due accounts receivable before year-end or early 2014, resulting in an enterprise value of EUR400 million. The majority of the debt will be repaid by Domtar in connection with the closing of the transaction.” John D. Williams, President and CEO of Domtar, commented, “The acquisition of Indas advances our transformation into a leader in Personal Care, an attractive market segment that is an important growth engine for Domtar. With the addition of the new business, Domtar will become one of the leading adult incontinence products manufacturers in Europe.”

Double A Agrees to Buy Pulp Mill in AlizayThailand-based pulp and paper producer Double A said that on December 17 it agreed to acquire the pulp mill and bio-mass power plant that is situated next to the site of its Alizay paper mill in France. Terms of the deal were not disclosed. Double A is buying the pulp mill from the Department of Eure in Northern France. Jean Louis Destans, Chairman of the General Council of the region of Eure, said, “We have agreed on the selling price of the land, the buildings and the assets necessary to revive the produc-tion site. All that remains is for us to prepare and sign the deeds as soon as possible. This is in both parties interest as it will initi-ate the revival of paper pulp production on the site.” On January 23, 2013, the Department of Eure bought the property and production assets of the Alizay pulp and paper mill site from Metsa Board for EUR 22 million. On the same day, the Department sold the paper mill to Double A for EUR 18 million. Double A said the investment in the pulp mill will also include investment in the site’s bio-mass power plant. Thirawit Leetavorn, Senior Executive Vice President of Double A, noted, “2013 marked a successful return of the Alizay Paper Mill, which returned to full production in June and was producing premium quality Double A paper by August. The mill began exporting paper in September to the UAE and Eastern Europe.” Double expects to restart the pulp mill in the first quarter of 2015.

SOUTH AMERICA

Suzano Starts Up New 1.5 Million TPY Pulp Mill in Maranhao

Suzano Papel E Celulose S.A. recently started up operations at its new pulp production unit located in Imperatriz, Maranhao, Brazil. The first bale of pulp was pro-

duced on December 30 with FSC certification, Suzano said. The new pulp mill will have eucalyptus market pulp produc-tion capacity of 1.5 million tons per year and surplus power generation of 100 MW Suzano said mill personnel are now focused on effectively executing the ramp-up period to ensure an adequate learning curve. Suzano expects the pulp mill to produce about 1.1 million tons in 2014.

Teresa Presas Marco Mensink

9PaperAge    JANUARY/FEBRUARY 2014

industry news

Page 10: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

SOUTH AMERICA

Fibria Continues Feasibility Studies on Expansion of Tres Lagoas Pulp Mill

Fibria announced that it is continuing with the feasibil-ity studies for the expan-sion of its pulp mill in Tres Lagoas (Mato Grosso do Sul State), Brazil. The company met with approximately 150 representatives of the main 36 equipment supplier com-

panies of the pulp industry in the interior of São Paulo state. “The idea behind the meeting was to invite [the representa-tives] to participate in the detailing stage of the project, which should be submitted to the approval of the Board of Directors by the end of the first half of this year,” Fibria explained. Fibria’s new pulp line in Tres Lagoas, which already has environmental licensing, and, if installed, will have a capacity 1.75 million tons per year, would increase the mill’s total pulp production capacity to 3.05 million tons per year, making it the largest pulp industrial unit in the world. Fibria said that it is making every effort to take advantage of a window of opportunity for the start-up of its new pulp capac-ity, and that it already has a major portion of the wood supply needed for the new plant’s operations. Fibria expects the new line to begin operations at the end of the fourth quarter of 2016. The Tres Lagoas mill opened on March 30 2009 and has a bleached eucalyptus kraft (BEK) pulp production capacity of 1.3 million tons per year. The mill is self-sufficient in energy, using biomass from eucalyptus and black liquor used in the industrial process.

Norske Skog and CellMark Agree to Paper Distribution Deal in AsiaNorske Skog and CellMark AB have entered a long term mar-keting agreement for sales of publication paper in the Asian markets and established a new distributor in Singapore, NorCell Asia, which holds exclusive marketing rights for all Norske Skog products to be sold in the Asian markets. Norske Skog is transferring its current sales operations and sales staff in Singapore from PanAsia Paper Trading to NorCell Asia. Norske Skog plans to release about USD 15-20 million in working capital by the cooperation with CellMark in the Asian markets.

INDUSTRY SUPPLIERS

Minerals Technologies to Build Satellite PCC Plant for UPM in ChinaMinerals Technologies has signed an agreement with UPM to build a satellite precipitated calcium carbonate (PCC) plant on-site at UPM’s paper mill in Changshu, China, located in Jiangsu province. The satellite plant will provide PCC — a specialty pigment for filling and coating high-quality paper — to the mill and have an initial capacity of 100,000 short tons. “We are extremely pleased that UPM, a premier global papermaker, has chosen Minerals Technologies’ PCC for their paper-filling needs at their mill in Changshu,” said Robert S. Wetherbee, CEO of Minerals Technology. “This is our fourth satellite agreement in China within approxi-mately one year, bringing our total to seven in that country.” The plant is scheduled to begin operation early in 2015.

Wuhan Chenming Starts Up Valmet-supplied Tissue Line in China

A new tissue line delivered by Valmet (formerly Metso Pulp, Paper and Power) successfully came on stream at Wuhan Chenming Hanyang Paper Co.

Ltd’s mill in Wuhan, China, in November 2013. This is the customer’s first tissue line, Valmet said. According to Valmet, the new Advantage DCT 200HS tissue line started up ten days before the estimated time and is now producing high quality tissue at high speed. With a width of 5.6 meters and an operating speed of 1,900 m/min, the new production line will produce 60,000 tons a year of high-quality facial, toilet and towel grades. The raw material for the new line is virgin pulp, Valmet said. The delivery comprised a complete production line with stock preparation equipment and an Advantage DCT 200 HS tissue machine including an OptiFlo II TIS multi-layer headbox, a cast alloy Yankee cylinder, an Advantage AirCap hood, an Advantage WetDust dust management system and an Advantage SoftReel reel. The delivery also featured Valmet’s patented Advantage ViscoNip pressing technology.

10 JANUARY/FEBRUARY 2014 PaperAge

industry news

Page 11: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

Paper2014 to be held at the New York Palace Hotel, March 23-25

The American Forest & Paper Association (AF&PA) and NPTA Alliance announced that Paper2014 will be held at the New York Palace Hotel, March 23-25, 2014.

Paper2014 is the premier annual paper industry business convention, providing leading executives from across the industry with engaging sessions and unparal-leled networking opportunities.

The New York Palace, located on Madison Avenue, is newly renovated and will provide a stunning venue for networking in addition to being convenient to Midtown Manhattan restaurants and attractions.

Paper2014 and the New York Palace offers:

• Single location for meetings and programming that will maximize networking opportunities

• New for 2014! – Larger Tower Corner suite option is more than twice the size as previous hotels for entertaining up to 50 people.

• Best space, most amenities, with the greatest value for rooms and suites in midtown

• New for 2014! – Complimentary WiFi in guest rooms and suites

• New for 2014! – Dedicated hotel banquet staff to service your meeting needs

Paper2014 Suites

Official Paper2014 Suite holders will maximize visibility and strengthen relationships with customers, suppliers, manufacturers, publishers and distributors of printing paper, packaging material and industry suppliers.

Pre-reserve Your Suite Today

Suites sell fast and are being offered on a first come, first served basis. Take advantage of this great value before all suites are sold by contacting Nicole Boland by email at: [email protected] or call (312) 673-5828.

Paper2014 is hosted by the American Forest & Paper Association and NPTA.

India’s Printers at Odds with Paper Producers’ Price HikesIndia’s paper and board manufacturers in 2013 pushed through substantial price hikes that they say were necessary to offset ris-ing input costs, while the region’s printers have watched their profit margins shrink to unacceptable levels. According to a report in PrintWeek (India), paper and board producers in fiscal 2013 increased prices by 10 – 15%, and some cases as much as 20 – 30%. The papermakers attribute the price hikes to the increasing cost of domestic wood as well as imported materials such as pulp and coal, due to Rupee’s depreciation. “Paper mills are importing pulp wood, even if it is costlier by 30 - 40%, as domestic stocks are scanty. JK Papers cites the reason for this to be a disease outbreak that hit tree plantations in Andhra Pradesh three years ago; and because of this, the gross tonnage of wood availability has taken a nosedive. Though companies have stepped up farm forestry, it will take another couple of years before normalcy can be restored,” explains Anand Srinivasan, author of the PrintWeek report. In addition, India’s papermakers will have to deal with a reduction on import duties in 2014. “The domestic paper indus-try, which is struggling to cope with high input costs and chronic shortage of wood pulp, will face a new challenge in 2014 – duty-free import of paper from Southeast Asian countries,” said Anand Srinivasan, author of the PrintWeek report. However, India’s printers are unsympathetic and say the fre-quent price increases come without warning. In an open letter to the chairman of the Competition Commission of India (CCI) in New Delhi, the Sivakasi Master Printers’ Association (SMPA) called on CCI to take action against the paper mills that would stop what has been termed “unfair trade practice” and substan-tially reduce the arbitrarily increased prices, as well as to direct the mills to maintain prices at least for a period of four months. “The print industry needs to be protected from the clutches of paper mills which are into the process of making print indus-try a scapegoat at the altar of price increase, leading to the ques-tion of survival in the future,” SMPA wrote. Domestic printers point out that many have annual contracts with their customers and are unable to pass along the increases. “The price has increased twice or thrice in the last two quarters of 2013, taking the landed prices up by 20–30%. It has hit the bottom line, as the cost cannot be passed on to the customers in near terms,” said Vasant Goel, Director, Gopsons Papers, one of India’s largest integrated print houses. For now, Srinivasan says, many printers are resorting to buying from cheaper mills or considering importing paper stocks despite the Rupee’s depreciation.

11PaperAge    JANUARY/FEBRUARY 2014

industry news

Page 12: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

PA P E R

n Ahlstrom announced that Sakari Ahdekivi has been appointed Chief Financial Officer and member of the company’s Executive Management Team. He will join Ahlstrom on February 1. Prior to Ahlstrom, Ahdekivi was Managing Director at Tamro Finland and Baltics.

n Appvion announced that Matt Denton has been appointed Senior Vice President and General Manager of the com-pany’s carbonless and security papers business; and Jason Schulist has joined Appvion as Vice President of Continuous Improvement.

n Atlas Paper Mills has named Jim Brown as Chief Executive Officer. Brown succeeds Joe Tadeo, who left the company to pursue outside interests. Brown most recently served as an Executive Vice President at Duro Bag Manufacturing Company.

n Greif has appointed Peter Watson as Chief Operating Officer of the company. Watson was group president responsible for Greif’s Paper Packaging and Land Management business segments as well as Global Sourcing & Supply Chain and the company’s Greif Business System capabilities.

n Mac Papers has named Craig Boortz as the new Vice President and Regional Manager. He succeeds Steve Bethea, who is retiring after more than 42 years with the company. In a related move, David McGehee, Jr., succeeds Boortz’s as General Manager in Greenville, SC.

n PaperWorks Industries has named William McSwain as interim President and CEO, replacing Mark Staton, who departed in January. McSwain is a seasoned business executive with leadership experience in many industries.

n Rayonier has elected Lynn Wilson to the position of Executive Vice President, Forest Resources. Wilson is a member of Rayonier’s senior management team and is responsible for 2.6 million acres of timberland in nine states and New Zealand.

Jason Schulist

n Twin Rivers Paper Company announced that Tony Rigelman has joined the company as Vice President, Sales. Rigelman has over 19 years of industry experience in a variety of leadership roles, serving most recently as Director of Sales for Technical and Specialty Papers at Domtar.

I N D U S T RY S U P P L I E R S

n Ashland Water Technologies has hired Jeff Fulgham as vice president, market-ing. He most recently served as chief sales and strategy officer for Banyan Water, based in San Francisco.

n OASIS Alignment Services has named Brian J. Hiltunen as President. He succeeds Ray Masse, who will continue as Chairman of the Board. Previously, Hiltunen served as Vice President and General Manager for OASIS.

n Thiele Kaolin Company recently announced the following changes within its sales leadership: Eric Tillirson has been promoted to Senior Vice President and Director of Sales Development; Mike Markillie has been promoted to Director of World Wide Sales and Technical Service; Scott Ahrens has been promoted to North American Sales Manager; and Tom Bennett has been promoted to Sales and Marketing Manager.

I N D U S T RY- R E L AT E D

n The Confederation of European Paper Industries (CEPI) has appointed Gary McGann as its new Chairman. McGann is Group CEO of Smurfit Kappa. He succeeds outgoing chairman, Jussi Pesonen, the President and CEO of UPM.

n University of Maine alumna Carrie Enos has been named president of the University of Maine Pulp & Paper Foundation. She replaces Jack Healy ‘74, who has held the position since 2007 and is retiring this spring. Enos has worked in the paper industry since 1997, most recently in the position of finished products business unit manager at the Verso Paper Mill in Bucksport.

Sakari Ahdekivi

Peter Watson

Jeff Fulgham

Brian Hiltunen

Gary McGann

Carrie Enos

Matt Denton

12 JANUARY/FEBRUARY 2014 PaperAge

people

Page 13: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

13PaperAge    JANUARY/FEBRUARY 2014

calendar

FEBRUARY 3-6, 2014 Paper Week Canada - 100th Anniversary PAPTAC Fairmont Queen Elizabeth Hotel Montreal, Canada www.paperweekcanada.ca/

FEBRUARY 11-12, 2014 Forest Products Investment Conference RISI Grand Hyatt New York New York, New York, USA www.risiinfo.com/events

FEBRUARY 26-28, 2014 ASPI Spring Meeting Association of Suppliers to the Paper Industry Ritz-Carlton Sarasota, Florida, USA www.aspinet.org

MARCH 18-21, 2014 Tissue World Americas UBM Asia Trade Fairs Miami Beach Convention Center Miami, Florida, USA www.tissueworld.com

MARCH 23-25, 2014 Paper2014 AF&PA and NPTA New York Palace Hotel New York City, New York, USA Contact: Nicole Boland (NPTA) [email protected]

APRIL 2-4, 2014 Spring Outlook and Strategies Conference Paperboard Packaging Council Royal Sonesta Hotel New Orleans, Louisiana, USA www.ppcnet.org

APRIL 27-30, 2014 PaperCon TAPPI Nashville Convention Center Nashville, Tennessee, USA www.papercon.org

MAY 4-7, 2014 International Pulp Week Pulp and Paper Products Council (PPPC) The Drake Hotel Chicago Chicago, Illinois, USA www.internationalpulpweek.com

JUNE 3-5, 2014 PulPaper 2014 Adforum Helsinki Exhibition & Convention Centre Helsinki, Finland www.pulpaperevent.com

June 22-25, 2014 71st Pulp and Paper Safety Conference Pulp and Paper Safety Association Renaissance Vinoy Resort St. Petersburg, Florida, USA www.ppsa.org

June 22-26, 2014 60th IEEE Pulp and Paper Industry Conference Institute of Electrical and Electronics Engineers Atlanta Marriott Buckhead Hotel Atlanta, Georgia, USA www.ieee.org

Tough little cookies. A crushed roll of paper can cost manufacturers and their customers countless hours, dollars, and headaches. But by simply inserting core plugs into each roll, paper makers can reduce damage and loss claims for just pennies per roll. As a family-owned New England company that has been producing core plugs for over 50 years, Souhegan guarantees a high-quality, steady inventory of the products you need, whenever you need them.

We offer two different types of high-density, molded wood core plugs engineered specifically for the paper industry:

CENTER HOLE PLUG

With an easy-out design preferred by many end-use customers, a crush strength of 2,300 lbs in a HQ5.5 core, and a competitive price, our re-engineered Center Hole plugs are an industry favorite for all grades of paper.

CORSAVER™ PLUG

Designed for fine coated papers, the name says it all – this little gem can withstand three times more pressure than most other center hole plugs on the market. In independent testing, our CorSaver plugs withstood a 10,000 lb crush in a HQ5.5 core.

For more information on standard plug sizes and custom options call us at (603) 654-2311 or visit us online at www.souheganwood.com

Page 14: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

14 JANUARY/FEBRUARY 2014 PaperAge

market grade

Over the course of the last 12 months the containerboard indus-

try was characterized by relatively weak fundamen-tal demand for corrugated containers and rising capac-ity. However, despite these negative trends, the overall business benefitted from an approximate $100/ton price increase in major container-board grades and an increase in box prices as well. The biggest concern entering 2014, other than the basic strength of the global econ-omy, is the impact of a surge in new capacity, which could throw a monkey wrench into the works. The rise in prices and a muting of input costs — at least for a while as OCC prices fell to very low levels earlier in 2013 — were certainly noteworthy developments last year in the containerboard market. In April, a $50/ton increase was successfully passed on to converters that raised linerboard prices to about the $650/ton range. This was the second successful increase in an eight-month period, following a $50/ton increase that was enacted in September 2012. These increases signific- antly improved operating margins for the major producers. Containerboard mills were able to push through the increases despite several important indicators that wouldn’t seem to support an upward movement in prices, i.e. weak domestic demand for corrugated boxes, a steady decline on

OCC costs and a long term over supply situation in the box market. The increase was successful mainly due to the sweat and hard work on the part of board producers who took significant market-related downtime to keep inventories under control and the market balanced. At the end of the year and into early 2014, prices are reported to have held mainly steady despite somewhat weak box cut ups during the seasonally slow months of the year again due to down-time that sustained operating rates. As noted, OCC costs fell steadily from a peak almost $180/ton in late 2011 before

bottoming out at about $100/ton in early 2013. Since then, prices have posted a modest rebound but remain low. Many observers believe that as global containerboard demand accelerates in 2014, OCC prices will surge and this may pro-vide the impetus for prices to also rise further on liner and medium grades this year. U.S. box and containerboard data through November 2013 clearly demonstrate the impact of sluggish economic, job and personal income growth on the box market. For the first 11 months of 2013, box shipments were down 0.5% vs. the prior year at 331.2 billion square feet year-to-date, and down 2.5% vs. November 2012 levels. On an average week basis, which accounts for a different number of ship-

Capacity Bulge, Sluggish Demand Remain Challenges for Containerboard Market2013 wasn’t a bad year for containerboard mills but results were decidedly mixed. Price increases were enacted on board and corrugated

boxes in early 2013 that boosted margins, but underlying box demand was stagnant. 2014 offers hope that improved economic growth can propel box demand to stronger gains, but the impact of new containerboard capacity remains a nagging concern.

By Harold M. Cody

Significant new capacity came online in the second half of 2013. This includes tonnage

from the startup of Norampac’s new 330-inch, 525,000 tpy recycled linerboard machine at the

Greenpac mill in Niagara Falls, New York.

Page 15: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

15PaperAge    JANUARY/FEBRUARY 2014

market grade

ping days month to month, November box shipments were up 2.6%, according to FBA and AFPA data. Total contain-erboard production, at 31.9 million tons, was up 1.6% over the first eleven months vs. the prior year level, but down 4.5% in November vs. last year.

Export Markets Cooled in 2013The export market continues to be an important market for U.S. mills, with linerboard exports through November at 3.5 million tons according to AF&PA. However, this is down 0.6% vs. 2012 levels. While demand in some export markets has weakened the drop is also partly due to mills in North America diverting tonnage to domestic markets. The export market has appeared to be weak in recent months, with export prices reported to be down in Europe and weak in Latin America. The weaker pricing is a result of a slowdown in demand plus an excess of supply in several regions includ-ing North America and Europe. U.S. Bureau of Census data through the first three quar-ters of 2013 showed U.S. Kraft linerboard exports down 6.3% at 2.8 million tons vs. the same period in 2012. Exports to the largest U.S. export market, Western Europe, were off nearly 20% at 585,000 tons. Exports were also down significantly to Canada, while smaller drops were posted for Mexico, the Middle East and Africa. In contrast, exports to Central America and South America, at 438,000 tons and 439,000, were up by 3.6% and 11%, respectively, vs. 2012 levels. In turn, export prices are reported to have slipped as well in Europe and were under pressure in the fourth quarter in Latin America.

New Capacity a ConcernAs noted, significant new capacity came online in the sec-ond half of 2013 that is a cause for concern, but report-edly, so far, it hasn’t had a severe impact on the market. This includes tonnage from the startup of Norampac’s new 330-inch, 525,000 tpy recycled linerboard machine at the Greenpac mill in Niagara Falls, New York and the conversion of two newsprint machines to containerboard. This includes the addition of 150,000 tpy of linerboard by SP Fiber in Dublin, Georgia, and 300,000 tpy by Atlantic Packaging in Whitby, Ontario. The converted paper machine in Dublin has a 390,000 tpy capacity, but the net gain is 150,000 tpy because of switching another machine at the mill from board to news-print. Combined, the new machine and conversions added nearly one million tons of new capacity. All three machines came online in the 2nd and 3rd quarter of 2103. The impact of this tonnage, much of which was just beginning to hit the market late in 2013, is a major concern in 2014. Pratt also announced plans to build a 360,000 tpy containerboard mill by its box plant in Valparaiso, Indiana.

Box Demand and Consumer SpendingProbably the biggest unknown in the outlook for contain-erboard is box demand. The reasons behind the relatively poor performance recently in box demand is fairly obvi-ous: a sluggish U.S. economy in combination with weak job growth and poor growth in personal income resulted in weak growth in consumer spending. This is particularly true for key markets that consume a lot of corrugated board such as food and beverage. With sluggish or no growth in dispos-able income over the last few years, consumers spent less on packaged food and beverages. These uses are critical for box plants as they account for just under half of total U.S. box shipments. Major food companies also reported lackluster results, mirroring the poor performance of corrugated boxes.

Looking AheadLooking forward into 2014, there is hope that the U.S. and European economies will perform better than they did in 2013, and this could provide a modest boost in box demand. Many economists believe that the U.S. economy could expand at closer to a 4% rate this year vs. weaker growth pegged at about 3% in 2013, which is coming on the heels of 2.8% and 1.8% growth in GDP in 2011 and 2012, respec-tively. Similarly, Europe’s GDP fell in 2012 and was expect-ed to post little or no gain in 2013. However, projections call for modest growth in the Euro area economy in 2014. Notable structural changes in the containerboard mar-ket in recent years, and which continued in 2013, will also likely impact the market’s supply and demand balance as well as the direction of pricing. Major mergers and acqui-sitions, including two major ones in 2013, have resulted in the top five containerboard producers now accounting for 75% of U.S. capacity. The most recent deals closed last year include Kapstone’s $1 billion acquisition of Longview Fibre and PCA’s $2 billion acquisition of Boise. Kapstone’s deal moved the company into the No. 5 position in North American containerboard capacity, behind International Paper, RockTenn, Georgia-Pacific and PCA. A rebound in the U.S. economy and thus improved box demand would be of great benefit to producers, who wouldn’t have to continue to take downtime and also would result in higher operating rates. It would also go a long way in accommodating the recent capacity that has been added and allow producers to maintain a more balanced market. Given the recent weakness and new capacity it’s unlikely any major movement in prices can be expected early this year. However, if the U.S. and global economy improves, and input costs such as for OCC begin rising, producers are likely to seek additional increases later in 2014. n

Harold Cody is a contributing writer for PaperAge. He can be reached by email at: [email protected].

Page 16: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

16 JANUARY/FEBRUARY 2014 PaperAge

heads up

It’s hard to spot unless you’re a chemist in an industry lab, where there’s

a lot happening in cellulose and nanotechnology. Or if you build with wood you’re doing well here in Europe. I con-tacted the top five European pulp and paper companies, spoke with two consultants, and attended two major con-ferences (Hawkins Wright and European PaperWeek). The conclusion: not a lot is happening. Yes, Domtar just completed its acquisition of the Spanish personal care products manufacturer Indas, and Double A of Thailand (formerly Advance-Agro) has announced plans to restart the Alizay pulp mill that sits next its paper mill in France, but that’s about it.

Bits and PiecesYet there is some significant and positive action in recy-cling, security papers and tissue. The industry has success-fully lobbied the European Parliament to block a proposal by the EU to reclassify wastepaper — the vote was 606 “for” and 77 “against.” This proposal would have classified wastepaper as “recycled” even before it’s been recycled! The vote in Strasbourg will save more than 20,000 ‘green’ jobs in the industry and 140,000 indirect jobs in Europe. If this legislation had passed it would have relaxed the EU’s waste management rules and triggered a flight of wastepaper from the EU to Asia, pushing up prices in Europe and undermin-ing the quality of wastepaper available to the EU recycling

industry. The consequences could have been devastating. Paper recycling in Europe would have dropped from 47 million tpy to 37 million tpy, leading to mill closures and the disappearance of hundreds of recycling operators. In a symbolic act in September 2013, CEPI tempo-rarily dumped bales of waste-paper in front of the EU’s headquarters in Brussels to draw attention to the problem. So now it’s back to the draw-ing board to try and solve the problem of when does paper cease to be classified as waste? It so happens that, at pres-ent in Europe, sourcing good

quality recycled fiber is becoming a problem, especially for the tissue sector.

Paper or Plastic?The Bank of England (BoE) has decided to replace British bank notes with plastic (polymer) notes. The job was expected to go to either De La Rue, the existing maker of BoE notes, or Innovia, which manufactures most of the polymer notes around the world. The Bank promised a con-sultation process last October but by January it was a done deal with Innovia. The Bank has ruled out importing plastic money from China. Mark Carney, formerly the Governor of the Bank of Canada, is now Governor of the BoE. While Governor of the Bank of Canada he introduced in 2011 a change of paper to plastic for $100 bills. Canada has since gradually

Quiet Start in EuropeThe European paper industry is off to a relatively quiet start in 2014, and industry observers say the year may continue as such, which may be a good thing.

By David Price

Waste paper or recycled? In September 2013,

CEPI temporarily dumped bales of waste paper in

front of the European Commission’s headquarters

building in Brussels to draw attention to the

EC’s proposal to redefine recycled paper.

Page 17: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

17PaperAge    JANUARY/FEBRUARY 2014

heads up

switched to plastic $50, $20, $10 and $5 bills. They say a plastic bank note is tougher to counterfeit, lasts longer and can be cleaned. But I also hear that vend-ing machines must be upgraded in order to accept them. Bottom line: the Bank of Canada says they’re here to stay. If this is the future of bank notes in the UK, what will happen to the traditional British printers and producers of security papers? It will be a massive blow said one manufacturer who did not want to be named. A consultant to the industry told me it will be a big hit on this specialist sector, but it will survive as De La Rue and others are major suppliers of paper bank notes to countries all over the world. The money and ownership trail of Innnovia is fascinat-ing. It is an off-shore company and its owners plan to sell it to Pamplona Capital Management, a fund backed by the Russian billionaire, Mikhail Fridman. The Guardian news-paper commented, “If the Bank thinks it unacceptable for British currency to be in Chinese hands, are Russian hands any more acceptable?”

Reusable DiapersDespite the biggest baby boom in the UK in 40 years, sales of diapers have fallen nearly 4% in the last year. Sales of

Pampers (P&G), which dominates the UK market, have fallen by 4.1% according to the trade magazine The Grocer. The UK diaper market is worth $800 million a year and Pampers sold 76.3 million fewer diapers last year despite its biggest rival, Huggies (Kimberly-Clark), exiting the UK and European market last October. K-C’s shock exit closed mills in UK, Italy, Spain and Poland with the loss of 1500 jobs. Consultants think the drop in sales is due to middle class households doing their bit for the environment and families switching from the big brands to cheaper diapers from the discount retailers as household budgets shrink. Own-label products are up by 37.3% and volume sales have risen 44.5% But P&G, SCA and the Italians — with 7 million tpy of tis-sue production in Europe — seem unfazed by this trend. I’m not convinced there’s a long term market for reusable diapers. I think it’s fashionable and green and will not last. If you think through the detail of cleaning, separating and reusing a soiled diaper, the technical and hygienic issues are considerable. And there is solid evidence the tissue makers are rethinking their use of recycled fiber in their products and are turning, increasingly, to virgin fiber. n

David Price is a contributing writer for PaperAge. He can be reached by email at: [email protected].

EASY OPEN ... EASY CLOSE

Use the powerof your forklift to open railroad box

cars with no damageto the box car door.

EASY-SLIDEinterior docks

U.S. Pat No.8,658,078

ALDORexterior docks

Watch these and other products in action:aldoninfo.com/videos

ASK FOR OUR110th ANNIVERSARY

CATALOG

ALDON COMPANY, INC. 847.623.8800 | aldonco.com | [email protected] | Waukegan, IL 60087

products for railroad safety and track repair

2008WORLD

FINANCIALCRISIS

2014

1995FREIGHTTRAFFICREACHES 1.3 BILLIONTON-MILES

1992DOUBLE STACK

CONTAINERSERVICE

2004

1987BLACK

MONDAYSTOCK

MARKETCRASH

1994

1980STAGGERS ACTDEREGULATES

RAILROADS

1984

1970CONGRESS

CREATESAMTRAK

1965100 TONCARENTERSSERVICE

1964 1974

www.aldonco.com

2009WARRENBUFFETBUYS BNSF

Page 18: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

18 JANUARY/FEBRUARY 2014 PaperAge

Dryer performance audits have been used for years as part of efforts to optimize the papermaking process. These audits involve quantifying dryer performance

indicators and comparing the indicators to performance standards. Some of the traditional indicators are not easily applied since they require special measurement techniques and a highly experienced assessor. Others are easily applied and are valuable to optimization efforts. Five easily applied dryer performance indicators that provide a good indication of dryer section energy efficiency include:

• Hoodexhausthumidity

• Dryersectionsupplyairflowrelativetodryersectionevaporation load

• Dryersectionsupplyairtemperature

• Energylossesfromthesteamsystemrelativetototalsteam dryer steam consumption

• Highpressuremotivesteamconsumptionasapercentoftotal dryer section steam consumption

Commonly applied standards for these indicators, the reasoning behind the standards, and considerations related to assessing the indicators are highlighted the following discussion.

HOOD EXHAUST HUMIDITYTAPPI standards specify the exhaust air drawn from the dryer section hood be 0.04 to 0.07 kg w.v./kg d.a. (300 to 500 grains) for “open” type hoods, 0.13 kg w.v./kg d.a. (900 grains) for “medium humidity” closed type hoods with fully enclosed basements, and 0.17 kg w.v./kg d.a. (1200 grains) for “high humidity” closed type hoods. Operating a hood with excess exhaust (and too low a humidity) lowers the air temperature surrounding the sheet, dryers, and dryer fabrics. It also increases the radiation and convection heat losses and reduces the effectiveness of heat recovery equipment

Easy-to-apply

Dryer Performance Indicators

Photo courtesy of Kadant Johnson Inc.

The dryer section is a large consumer of energy, but ensuring it is operating efficiently is not difficult. By assessing only a few easily applied “dryer performance indicators”, one can determine whether large improvement opportunity exists.

By Jeff Chaloux

Page 19: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

19PaperAge    JANUARY/FEBRUARY 2014

energy efficiency – dryer section

installed on the hood exhaust sys-tems. Operating a hood with insuf-ficient exhaust positively impacts energy efficiency, but it risks opera-tional problems such as dripping on the sheet, corrosion of equipment, and spillage of heat and humidity to the machine room. Hood exhaust humidity can eas-ily be assessed by inserting a wet and dry bulb thermometer into the hood exhaust flow stream. For an accurate measurement of wet bulb temperature, the air velocity passing across the wet bulb should be greater than 3 m/s. Many dryer sections operate with inappropriate amounts of exhaust. Figure 1 shows average hood exhaust humidities for several recently measured operating paper machines.

DRYER SECTION SUPPLY AIR FLOW RELATIVE TO EVAPORATION LOADThe rate of hot air supply to the dryer section should be appropriate for the rate of evaporation from the dryer sec-tion. If it is not, there is opportunity to save energy or improve drying performance. Most paper machines are operated with a heated supply air system serving the dryer section. The delivery of heated supply air to the dryer section lowers the relative humidity of air surrounding the sheet and drying equipment. Nearly all dryer sections that operate with no form of dryer section supply air system are unfelted dryer sections that lack felt rolls. On dryer sections with dryer fabrics, having heated supply air is normally necessary to avoid felt roll corrosion. TAPPI standards specify pocket air humidity be between 0.12 to 0.28 kg w.v./kg d.a. For high-speed machines making lightweight grades, excessive air supply to dryer pockets can negatively affect web stability. For machines that do not have problems with sheet flutter, it is suggested the air sup-ply to the dryer section target a humidity of 0.20 kg w.v./kg d.a., which is the median of the recommended humid-ity range by TAPPI. To achieve this pocket humidity, the amount of air that must flow into the dryer pocket is 4.2 kg d.a./kg evaporation. To assess the supply air flow rate per unit evaporation, both the dryer section evaporation load and the total supply air flow rate must be assessed. The dryer section evaporation load can be quantified with a simple drying rate calculation.

(See TAPPI TIP 0404-24 for guidelines on calculating the evaporation load.) The total supply air flow rate to the dryer section should be assessed with field measurements. For most hot air supply systems, the best method for measuring flow rate involves using a vane anemometer at the face of air intakes.

DRYER SECTION SUPPLY AIR TEMPERATUREAssessing supply air temperatures for pocket ventilation systems is normally easy. If online indication does not exist, temperatures can be easily measured with a thermocouple probe inserted into the supply air stream. The TAPPI rec-ommended supply air temperature for dryer section supply air systems is 82 to 93°C. Temperatures significantly lower than this range are usually inappropriate since they increase risk of condensation, dripping, and corrosion of equipment. Temperatures significantly above this range are usually inappropriate since they significantly increase energy demand while providing little benefit.

ENERGY LOSSES FROM THE STEAM SYSTEMAn energy efficient steam system operates with few losses. By far, the easiest way to assess the energy efficiency of a steam and condensate system is to quantify steam losses from the system and compare them to total dryer section steam consumption. Alternative methods of assessing steam system energy efficiency, which include evaluating steam consumption per unit evaporation or steam consumption per unit production, have clear shortcomings. Realize that the waste steam flows that hurt steam system energy effi-ciency are normally small relative to total dryer section steam consumption. When quantifying steam consumption

Figure 1 – Measured Average Hood Exhaust Humidities on Active Paper Machines

0.250

0.225

0.200

0.175

0.150

0.125

0.100

0.075

0.050

0.025

0.0000 500 1000 1500 2000

Avg.

Exh

aust

Hum

idity

(kg

w.v

./kg

d.a.

)

Recommended for High Performance Hoods

Recommended for Closed Hoods

Recommended Range for Open Hoods

Machine Production Rate (Metric TPD)

Open HoodsClosed HoodsHIgh Performance Hoods

Page 20: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

20 JANUARY/FEBRUARY 2014 PaperAge

per unit evaporation, highly accurate information on steam consumption and evaporation load are needed just to get a rough indication of steam system energy efficiency. An energy efficient steam and condensate system will have total “losses” that equate to less than 3% of total dryer section steam consumption. Following are the most prevalent forms of energy losses from a steam and condensate system. Venting from steam sections through automatic vent

valves. A well-designed steam system with properly func-tioning devices will vent no steam during “sheet on” condi-tions. Open vent valves during “sheet on” conditions gener-ally indicate a steam system deficiency or equipment prob-lem. If venting is occurring, the recommended technique for quantifying the steam lost is a simple steam valve flow calculation. Steam losses to a condenser. Paper machine dryer sec-tions with cylinders operating at low pressure are equipped with one or more vacuum condensers. When assessing steam system energy efficiency, the steam energy losses to the con-denser are viewed as waste. This is even for cases where the warm water from the condenser appears to be fully utilized. For most paper machines there is potential to either reduce the demand for warm water or to generate the required warm water using a form of heat recovery. The best technique for quantifying the steam energy losses to a condenser measures the water flow rate with a portable water flow meter and the inlet and outlet water temperature. Modern “transient time” meters are well proven for the suggested water flow measurement. An easy method for assessing water inlet and outlet temperature is to paint black “spots” on uninsulated portions of inlet and out-

let water piping, and to then measure the line temperature with an infrared pyrometer. Flash steam losses from Main Condensate Tank. A good steam system is designed such that flash steam generated at a main condensate collection tank is put to good use. Flash steam losses to atmosphere should be completely avoided. The best use of low-pressure flash steam is for any cylinders being operated at low pressure. Another potential good use for flash steam is at pocket ventilation supply units equipped with flash steam coils. Yet another potential good use for flash steam is at steam showers or steam boxes. If flash is used for steam showers and steam boxes, appropriate safeguards against condensate carry-over must be applied. A realistic goal is to have no flash steam losses to atmosphere.

HIGH PRESSURE MOTIVE STEAM CONSUMPTIONA common type of steam system for paper machine dryer sections is a thermocompressor type system. This system uses high-pressure motive steam for recompressing blow-through steam. For those mills that have steam-driven turbine gener- ators, high-pressure steam is more valuable than turbine exhaust steam. The high-pressure steam can be passed through the turbine generator so that relatively inexpensive thermal energy is converted to a more valuable electrical energy. For mills with turbine generators, the paper machine dryer section should draw as high a percentage as possible of its total steam demand from headers being fed by turbine exhaust and as little a percentage as possible from headers being fed high-pressure steam that has not passed through turbine generators, or has only partially passed through turbine generators to an intermediate extraction point. Potential methods for reducing motive steam consump-tion include:

• Replacinginefficientthermocompressorswithproperlysized high-efficiency units.

• Upgradingrotarysyphonstostationarysyphons

• Improvingtheaccuracyofdifferentialpressuretransmit-ters so that differentials can be minimized.

• Activelymanagingdifferentialpressuresasafunctionofmachine operating conditions so that excessive differ- ential pressures are avoided. This is best done through application of supervisory control logic.

The dryer section is a large consumer of energy, but ensur-ing it is operating efficiently is not difficult. By assessing only a few easily applied “dryer performance indicators”, one can determine whether large improvement opportunity exists. n

Jeff Chaloux is a Senior Process Engineer for Kadant Johnson Systems Division. He can be reached at: [email protected].

energy efficiency – dryer section

Dryer Performance Indicator Recommended Level Hood exhaust humidity 0.04 to 0.07 kg w.v./kg d.a. for an “open” hood 0.13 kg w.v./kg d.a. for a medium humidity closed hood 0.17 kg w.v./kg d.a. for a high humidity closed hood

Dryer section supply air flow 5 to 7 kg d.a./kg w.v. relative to dryer section evaporation load

Dryer section supply air 82 to 93°C temperature

Energy losses from the steam Total combined steam losses system relative to total steam less than 3% of total dryer dryer steam consumption section steam consumption

High-pressure motive steam 4 to 8% of total dryer section consumption as a percent of steam consumption

total dryer section steam consumption

Page 21: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

T U E S D A Y , M A R C H 1 9 , 2 0 1 3

The federal government is increas-

ingly pushing Americans into digi-

tal-only information delivery, often

without regard to how these policies

affect key demographic groups, in-

cluding senior citizens, non-English

speakers, those who do not have

ready computer access, and those

concerned about identity theft and

electronic security. These actions

are being taken with little or no U.S.

Congressional oversight and with-

out ample opportunity for public

input. “This issue does not attract the

same kind of attention as the fiscal

cliff or air regulations, but govern-

ment mandates that decrease the

demand for paper are a threat that

our industry needs to pay atten-

tion to, particularly since they set

the stage for adoption in the pri-

vate sector,” says AF&PA President

and CEO Donna Harman. “And in

this case, the federal government is

hurting vulnerable citizens by tak-

ing away access to the paper option

they need.”No more paper Social Security

checksIn the latest move by the U.S. Trea-

sury Department, on March 1, mil-

lions of Americans were forced to

switch from traditional social secu-

rity checks to electronic direct de-

posit or a Treasury-issued debit card

to receive federal benefits for Social

Security, SSI disability, veterans’ and

other federal programs. In addition,

the Social Security Administration

has already eliminated the mailing

of annual earnings statements, an

important financial planning tool

used by millions of Americans.

No more paper savings bondsAt the end of 2011, the savings bond

program went all-digital, replacing

paper savings bonds with an online

process that requires an online ac-

count for both the recipient and the

giver. To activate an online Trea-

sury account, users must divulge

personal information such as their

Social Security number — opening

them up to the rising risk of cyber-

fraud. Anecdotal reports indicate

that many long time bond buyers

will no longer use this important

savings tool.No more tax forms in the mailboxThe IRS no longer distributes an-

nual tax forms. While the IRS wants

taxpayers to file electronically, mil-

lions of citizens still file their return

Preserving Paper as Part of Federal Information Policy

Schedule of Events(all meetings and events are being held

at the Fairmont Chicago)TUESday, March 19, 2013• 8:00a.m.–4:00p.m. Paper2013 Registration Paper2013 Convention Daily Desks P’13 Lounge Moulin Rouge Room, Lobby Level

• 8:00a.m.–12:00p.m. Official Hospitality Suites Open

• 12:00–2:30p.m. Paper2013 Luncheon Sponsored by Graphic Packaging

and International Paper InternationalBallroom,2ndLevel

• 2:30–6:00p.m. Official Hospitality Suites Open

Convention Daily

As the first quarter of 2013 unfolds,

Congress is embroiled in fiscal pol-

icy debates. While Congress passed

tax legislation in early January, other

fiscal issues were left for the Con-

gress to address this spring. AF&PA is working to educate

members of Congress about the in-

dustry’s economic impact and our

commitment to sustainability. Every

issue the industry faces has an effect

on its 900,000 workers — whether

dealing with marketplace challeng-

es, a struggling economy, or stifling

government regulations. Through

working with our member compa-

nies and industry allies, AF&PA has

identified several priority issues

including postal reform; biobased

labeling and federal procurement;

paperless government; tax; air regu-

lations; and energy.

Postal ReformApproximately one-third of printing

and writing paper demand is deliv-

ered through the mail system. With

financial losses exceeding $15 bil-

lion in 2012, the U.S. Postal Service

(USPS) must change significantly

to return to profitability and estab-

lish a sustainable business model.

Their attempt at a solution was a

hasty announcement to eliminate

six-day mail delivery effective Au-

gust of this year. This decision will

put mailing industry jobs at risk.

AF&PA will continue to support leg-

islative measures that will help the

USPS achieve financial stability by

encouraging new revenue sources,

attracting customers, and realizing

cost savings without sacrificing cus-

tomer-facing opportunities to gen-

erate new business.

AF&PA Congressional Priorities

Find out how Glatfelter is investing in your success — Suite 523 at the Fairmont Chicago, Millennium Park | www.glatfelter.com

SEARCHING FOR A SUPPLIER THATNEVER STOPS IMPROVING?

At Glatfelter we are committed to continually improving every aspect of our business, investing

in capabilities, products and PEOPLE so that we can keep your business moving forward.

gla001901-01PaprWk13Bnr-D11d.indd 3

2/28/13 10:18 AM

Biobased Labeling and Federal

Procurement USDA’s Biobased Markets Program

comprises two separate initiatives:

Product Labeling, which allows the

USDA to authorize manufacturers

and vendors of biobased products

to use a “USDA Certified Biobased

Product” designation on products in

the marketplace, and a Federal Pro-

curement Preference, which gives a

preference for the purchase of bio-

based products by the federal gov-

ernment. Despite the clear language

of the 2008 legislation defining a

“biobased” product as “a product

composed in whole or significant

part of biological products, includ-

ing renewable domestic agriculture

and forestry materials,” USDA ar-

bitrarily excludes the majority of (continued on page 5)

(continued on page 4)

PAPER

900366_Pap2013_TUE_20.indd 1

3/7/13 3:46 PM

Due to comprehensive networking of Paper2014 attendees, the Paper2014 Convention Daily offers a unique advertising opportunity for:

Published during Paper2014 in New York, the Paper2014 Convention Daily delivers news and industry information such as:

• Pulp producers

• Paper manufacturers

• Tissue manufacturers

• Paperboard producers

• Paper converters

• Paper merchants

• Suppliers of equipment and service

• A complete, up-to-date schedule of meetings and activities

• Program reviews

• Session reports

• Speaker interviews

• Industry news and statistics

• Hospitality suite locations and contact information

Paper2014 is scheduled for March 23-25, 2014 in New York.

For further information on advertising opportunities in the Paper2014 Convention Daily, please contact:

Mike O’Brien, Publisher • O’Brien Publications, Inc./PaperAge • 20 Schofield Road • Cohasset, MA 02025-1922 Telephone: 781.923.1016 • Fax: 781.923.1389 • e-mail: [email protected]

The Paper2014 Convention Daily will be published in three separate editions (March 23rd, March 24th, and March 25th) and distributed to all attendees of the Paper2014 meeting in New York. The Paper2014 Convention Daily is published by O’Brien Publications, Inc.

Reach Decision Makers

M O N D A Y , M A R C H 1 8 , 2 0 1 3

On behalf of the American Forest & Paper Association (AF&PA) and the NPTA Alliance, we are honored to welcome you to Paper2013. This annual event is where our industry meets. This year in Chi-cago, the theme is Passport to Op-

portunities. Paper2013 will provide a number of opportunities to gain new perspectives, share insights and network with fellow paper industry executives. This year’s program focuses on the opportunities in emerging mar-

kets, and business and demographic trends that affect the paper and pa-per-based packaging industry. Over the next two days, company suites are open so we can check in with key clients and suppliers and connect with existing and potential new business contacts.

Thank you for joining us at Paper- 2013. We look forward to sharing the experience with you.David Scheible is President & CEO of Graphic Packaging International, Inc.; and Don Clampitt is CEO, Clampitt Paper Company.

Opportunities Abound in Chicago

Convention DailyPAPER

AF&PA – States are looking for new legislative ways to divert waste from landfills, for both environmental and economic reasons. A growing trend to address municipal solid waste and recycling is called extend-ed producer responsibility (EPR).

EPR is a policy that would shift total financial responsibility for the “end-of-life” recovery of packaging and printed paper from the mu-nicipality to the manufacturer or brand owner. This means that the companies who produce and/or use the printed product (magazines, newspapers, catalogs, packaging of consumer and durable goods etc.) and/or the companies who use that

packaging for their products would pay the costs of collecting that same packaging for either recycling or dis-posal. EPR can take one of four forms at the state level: 1) product-specific legislation; 2) framework legislation; 3) solid waste management plan; or 4) executive order. In 2013, Iowa, Maryland, Massachusetts, New Mex-

ico, New York, and Rhode Island in-troduced solid waste management/recycling and EPR legislation. The paper and paper-based pack-aging industry recognizes the im-portance of recycling and diverting materials from landfills, which is why it has spent considerable re-sources to build a market-based in-frastructure to recover and recycle its own products. The industry con-tinues to inform and remind legisla-tures of its recycling commitment. More than 60 percent of paper con-sumed in the U.S. has been recov-ered for recycling in each of the last three years, exceeding 66 percent in

Extended Producer Responsibility – A Solution Seeking a Problem

Learn why Glatfelter has been in business for 149 years — Suite 523 at the Fairmont Chicago, Millennium Park | www.glatfelter.com

WANT A SUPPLIER THAT’S THERE FOR YOUTODAY AND TOMORROW?Since the days of President Lincoln, Glatfelter has served the paper industry with an unwavering commitment to quality, service and sustainability. Today we are a financially strong global supplier, capable of meeting your most challenging demands.

gla001901-01PaprWk13Bnr-D11d.indd 2

2/28/13 10:19 AM

2011. The industry’s recovery rate far outpaces all other commodities in the municipal solid waste stream. The goal of EPR — to increase re-covery rates and reduce the amount of recyclable products going to landfills — is commendable. How-ever, serious concerns exist regard-ing the practical implementation of any specific product stewardship

Don Clampitt, Chairman, NPTA

David Scheible, Chairman, AF&PA

This year’s program focuses on the opportunities

in emerging markets, and business and demographic trends that affect the paper

and paper-based packaging industry.

EPR is a policy that would shift total financial

responsibility for the “end-of-life” recovery of

packaging and printed paper from the municipality to the

manufacturer or brand owner.

(continued on page 6)

Schedule of Events(all meetings and events are being held at the Fairmont Chicago)

MOndAy, MARch 18, 2013• 7:00a.m.–5:30p.m.

Paper2013 Registration Paper2013 Convention Daily Desks P’13 Lounge Moulin Rouge Room, Lobby Level

• 8:00a.m.–4:00p.m. Official Hospitality Suites Open

• 10:30–11:00a.m. Paper Check-off Information Session “Investing in our Future – The Paper Check-off” (opentoallPaper2013registrants) AmbassadorRoom,2ndLevel

• 4:00–5:30p.m. Industry Leadership Session (suites closed) Sponsored by Domtar InternationalBallroom,2ndLevel

• 5:30–6:30p.m. Paper2013 Reception (opentoallPaper2013registrants) InternationalBallroom,2ndLevel

TUESdAy, MARch 19, 2013• 8:00a.m.–4:00p.m.

Paper2013 Registration Paper2013 Convention Daily Desks P’13 Lounge Moulin Rouge Room, Lobby Level

• 8:00a.m.–12:00p.m. Official Hospitality Suites Open

• 12:00–2:30p.m. Paper2013 Luncheon Sponsored by Graphic Packaging and International Paper InternationalBallroom,2ndLevel

• 2:30–6:00p.m. Official Hospitality Suites Open

900365_Pap2013_MON_36.indd 1

3/7/13 2:03 PM

PAPER

S U N D A Y , MA R C H 1 7 , 2 0 1 3

On behalf of the American Forest

& Paper Association (AF&PA) and

the NPTA Alliance, welcome to

Paper2013 in Chicago!

This year’s “Passport to Opportu-

nities” includes a variety of sessions

and chances to network with your

industry colleagues.

Monday’s Industry Leadership

Session kicks off our program with

a distinguished panel of CEOs rep-

resenting key segments of the paper

industry, providing their perspec-

tives on emerging issues, trends and

the future of the paper industry.

During a Monday morning ses-

sion, Paper Check-off Panel mem-

bers answer questions industry par-

ticipants have about the proposed

Paper Check-off program and the

recently issued call for Board nomi-

nations.

Tuesday’s Luncheon features re-

spected author, economist, educa-

tor and speaker Dr. Jeffrey Rosens-

weig. Known for his unique ability to

deliver original and useful business

content in an engaging and dynam-

ic presentation style, Dr. Rosens-

weig will focus his presentation on

emerging markets as well as eco-

nomic, business and demographic

trends impacting the paper and

paper-based packaging industry.

During the Luncheon, David S.

McGehee of Mac Papers will be pre-

sented with the NPTA Stanley O.

Styles Industry Excellence Award.

Also on Tuesday, RISI hosts a sem-

inar on the market outlook for print-

ing-writing paper, paperboard, and

recovered fiber. Topics will include

influences from technology, Asian

supply growth, operating rates and

rising mill cash costs.

Throughout Paper2013, other

sessions, suite meetings and various

association committee meetings

will take place.

We hope that you find the pro-

gramming and networking opportu-

nities valuable and interesting. We

appreciate your participation and

wish you the very best for 2013.

Welcome to Paper2013

Schedule of Events

(all meetings and events are being held

at the Fairmont Chicago)

Sunday, March 17, 2013

• 12:00–6:00p.m.

Paper2013 Registration

Paper2013 Convention

Daily Desks

P’13 Lounge

Moulin Rouge Room, Lobby Level

• 4:00–6:00p.m.

Official Hospitality Suites Open

MOnday, March 18, 2013

• 7:00a.m.–5:30p.m.

Paper2013 Registration

Paper2013 Convention

Daily Desks

P’13 Lounge

Moulin Rouge Room, Lobby Level

• 8:00a.m.–4:00p.m.

Official Hospitality Suites Open

• 10:30–11:00a.m.

Paper Check-off Information

Session

“Investing in our Future –

The Paper Check-off”

(opentoallPaper2013registrants)

AmbassadorRoom,2ndLevel

• 4:00–5:30p.m.

Industry Leadership Session

(suites closed)

Sponsored by Domtar

InternationalBallroom,2ndLevel

• 5:30–6:30p.m.

Paper2013 Reception

(opentoallPaper2013registrants)

InternationalBallroom,2ndLevel

TuESday, March 19, 2013

• 8:00a.m.–4:00p.m.

Paper2013 Registration

Paper2013 Convention

Daily Desks

P’13 Lounge

Moulin Rouge Room, Lobby Level

• 8:00a.m.–12:00p.m.

Official Hospitality Suites Open

• 12:00–2:30p.m.

Paper2013 Luncheon

Sponsored by Graphic Packaging

and International Paper

InternationalBallroom,2ndLevel

• 2:30–6:00p.m.

Official Hospitality Suites Open

Convention Daily

Donna Harman

Kevin Gammonley

From Donna Harman, President & CEO, AF&PA

and Kevin Gammonley, CEO, NPTA Alliance

The Responsible Package initiative

promotes the versatile and sustain-

able packaging solutions provided

by paper-based packaging such as

paperboard, corrugated, and paper

bag and sack products.

To discover new ways to promote

the recyclability and sustainability

of paper-based packaging to young-

er generations, The Responsible

Package launched two projects. TRU

Research, a global leader in youth

research and insights, conducted

the first project, which explored Mil-

lennials’ (ages 16-27) views of pa-

per-based packaging. The research

identified actionable insights for the

paper-based packaging industry to

ensure the presence and use of its

products in future generations.

For the second project, The Re-

sponsible Package partnered with

youth and family-based educational

marketing firm Kaleidoscope to de-

velop a youth education outreach

program for 3rd - 6th grade students.

The program educates kids and their

families on the benefits of paper-

based packaging and helps them

to understand why paper-based

packaging is a responsible option or

choice.

The paper-based packaging in-

dustry has an impressive story to

tell, one that includes sustainable

forestry, exceptional recovery rates

for recycling, energy and waste

The responsible Package® Initiative — Paper-based Packaging

The research identified action-

able insights for the paper-based

packaging industry to ensure the

presence and use of its products

in future generations.

With highly specialized capabilities, world-class R&D and a powerful new product

development engine, Glatfelter consistently drives more than 50% of it’s business

from products developed in the last five years.

LOOKING FOR A pROveN tRAcK RecORd OF

INNOVATION AND EXPERTISE?

Find out how Glatfelter can help drive your business forward — Suite 523 at the Fairmont Chicago, Millennium Park | www.glatfelter.com

gla001901-01PaprWk13Bnr-D11d.indd 1

2/28/13 10:19 AM

management efficiency, and re-

duced environmental impacts —

all of which contribute to respon-

sible and affordable packaging

solutions.

Officially launched in 2009, The Re-

sponsible Package is funded by the

following organizations: American

Forest & Paper Association, Asso-

ciation of Independent Corrugated

Converters, Corrugated Packaging

Alliance, Fibre Box Association, Pa-

perboard Packaging Alliance, Pa-

perboard Packaging Council, Paper

Shipping Sack Manufacturers’ Asso-

ciation, and Renewable Bag Council.

To find learn more about our

most recent projects and learn more

about paper-based packaging, visit

www.theresponsiblepackage.com.

Be sure to follow us on Twitter too @

PaperbasedPkg.

900364_Pap2013_SUN_24.indd 1

3/7/13 11:21 AM

Place an ad in the Paper2014 Convention Daily

Page 22: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

22 JANUARY/FEBRUARY 2014 PaperAge

water treatment

Fresh water contamination of paper mill systems may lead to outbreaks of deposits of filamentous bacteria often collectively called “pink slime.” These deposits can

be difficult to treat with modern microbiological control programs, especially in mills where corrosion is a concern. We have adopted a methodology that uses DNA fingerprint-ing to identify problematic fresh water organisms. Once the microorganism is isolated and identified, we can then use our available biocidal actives to identify the most appro-priate formulations so that the deposit can be effectively treated. Even though problem organisms can manifest in similar ways, specific problem organisms can vary widely in the optimum product and MIC required to control them. Thus, by utilizing the state of the art technology to iden-tify problem organisms, we not only provide our customers with some of the most advanced control chemicals, but the resulting information is also entered into a database where

it can be retrieved to help identify and treat problems found in other mills.

INTRODUCTIONThe problems caused by uncontrolled growth of microor-ganisms in the production of paper are well known. These include odor, paper stains, web breaks, slime, blockage of pipes, and corrosion.1 Microorganisms enter the produc-tion system from a variety of sources such as raw materials, water, soil, and air. The control of microorganism is usually accomplished with the use of biocides and/or dispersants as well as good housekeeping including boil out of the system where appropriate. In preparation for effective microbial control of a system, a good audit of the system helps as this can give a picture of the types, nature, and the relative abundance of the microor-ganisms that may be causing the problem. The use of the

Microbiological Auditing and Control –

A genetic-based technique used to detect and identify troublesome microbes in paper mills’ fresh water systems has been found to be quick,

accurate, and less cumbersome than traditional methods.

By David Oppong and Tod Stoner

Editor’s Note: This article was first presented at PaperCon 2013.

A New and Powerful Approach to Controlling

Problem Organisms

Page 23: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

23PaperAge    JANUARY/FEBRUARY 2014

water treatment

microscope, visual inspection, ATP assays, and also microbial plate counts are some of the techniques frequently employed in the auditing process.

DNA methods for detecting and identifying microorgan-isms have become increasing popular. They have been used in the leather industry,2 pulp and paper 3, 4, 5, 6, 7 and have played significant roles in expanding our knowledge of the microbial flora of these environments. It would be advanta-geous if some of these techniques could be incorporated into microbiological auditing programs and routinely used to detect and identify troublesome microbes in paper mills. In this presentation, we describe a genetic-based identifi-cation technique that we have found to be useful and which we frequently employ together with the other established auditing tools when we initiate microorganism control in a system. We also present the use of these techniques in studying the “pink slime bacteria” in deposits from six different mills.

SAMPLING AND ISOLATION OF BACTERIAThe first step in using DNA based auditing method involves selection of sampling points. Typically, we obtain samples from several points of interest including water and slime deposits. Samples of slime deposits and incoming water are collected and sent to the laboratory for microbiological analyses. The samples are processed immediately after arrival at the laboratory. Samples are aseptically processed by serial dilution in sterile saline and plated on plate count agar, R2A agar, Stokes agar, and actinomycetes isolation agar. The plates are incubated at 30⁰C or 45⁰C-50⁰C (depending upon field conditions) for 2-7 days and colonies picked, and re-streaked to obtain pure cultures of bacteria. The isolation could also be done by streaking the original samples onto appropriate plates, but we usually use the serial dilution method as this also affords us the chance to estimate the relative numbers of bacteria that may be causing the problem.

DNA PREPARATION The genetic method for the identification is based on the MicroSeq system from Applied Biosystems, Foster City, California. The method requires the use of DNA from pure cultures of bacteria. The DNA is extracted from the cul-

tures using the instructions provided in the PrepMan Ultra Sample Preparation Reagent Protocol (Applied Biosystems).

GENE AMPLIFICATIONOnce DNA is obtained, a polymerase chain reaction (PCR) is run. PCR is a method for amplifying or making millions of copies of a particular gene sequence.8 In iden-tifying eubacteria, the 16S rRNA gene is amplified. This gene is used in the identification of most bacteria because it is expected to occur in all bacteria.9 The 16S rRNA gene is also conserved which means it has changed very little over the evolutionary period. Additionally, the 16S rRNA gene has regions of significant sequence variability that allows bacteria of different species to be differentiated or identified.10

A PCR reaction mixture would include the template DNA, primer set to initiate the reaction, thermostable DNA polymerase, nucleotides (dNTP’s), magnesium, and a buffer. All reagents and method for amplifying the 16S rRNA gene are contained in the MicroSeq 500 16S rDNA Bacterial Identification PCR Kit (Applied Biosystems). At the end of the reaction, the success of the PCR is checked by taking a sample of the reaction mixture and run-ning agarose gel electrophoresis. If the expected band can be visualized on the gel, the PCR is deemed to be successful and the product is cleaned up of the unreacted reactants.

16S rRNA SEQUENCING AND DATA ANALYSISThe cleaned amplified DNA is used in cycle sequencing. DNA sequencing is a method that allows us to determine the order or sequence in which the bases (A, T, G, C) occur in a particular gene or DNA. Cycle sequencing utilizes four different fluorescent dyes to covalently label the correspond-ing bases in the DNA. 11

16S rRNA gene sequences of the isolates are generated using the MicroSeq 500 16S rDNA Bacterial Identification Sequencing Kit (Applied Biosystems). After cycle sequenc-ing, the reaction mixture is cleaned up to remove unreacted reactants and unincorporated dyes according to the method provided by the manufacturer. The reaction products from the cycle sequencing are then electrophoresed on an automatic DNA sequencing machine. Sequence analysis and bacterial identification are per-formed using Applied Biosystems’ MicroSeq microbial analysis and database. In a case where there is no match, a BLAST search of the GenBank or Ribosomal Data Project is conducted for a possible match.

DNA methods for detecting and

identifying microorganisms have

become increasing popular.

Page 24: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

24 JANUARY/FEBRUARY 2014 PaperAge

water treatment

RESULTS AND DISCUSSIONA genetic-based identification system was used to study the composition of “pink slime bacteria” in pink slime deposits prior to instituting slime control programs. The samples came from mills located in the US, China, Germany and the Czech Republic. Detailed identification of the culturable bacteria was done for samples obtained from three of the mills. For the remaining samples, attempts were made to isolate only pink-or-red-pigmented bacteria. Table 1 shows the bacteria identified in the deposits from the various mills. In the six mills studied, the main cause of pink slime varied to include Flectobacillus sp, Runella sp, Meiothermus ruber, Deionococcus geothermalis, and Serratia marcescens. Flectobacillus sp. are pink-pigmented filamentous bacteria. In this work we found them in three of the mills studied. This study, coupled with our experience from many other studies, 3, 4, indicate that they are the main cause of pink coloration in many “pink slimes” in modern paper machines. In one mill, Flectobacillus sp. were found together with Rhodovarius lipocyclicus which were red-pigmented but short rods. Rhodovarius sp. have been found in other places12 but no information about their occurrence in the paper mill environment could be located. In one of the mills, the cause of the pink slime was found

to be Runella sp. These are filamentous bacteria and they have been isolated in a wastewater treatment plant13 and water bodies,14 but neither information about their occur-rence in paper mills nor their association with “pink slime” in paper mills has, to date, been published.

Meiothermus ruber and Deinococcus geothermalis were identified as the cause of the pink slime in one of the mills studied. In this mill, Meiothermus ruber was found to be the dominant pink or red-pigmented bacteria. These organisms are moderately thermophilic and they were isolated at 45 - 50˚C. The presence of Meiothermus sp. and Deionococcus geothermalis in slime deposits and as the cause of red or pink slime in paper machines has previously been reported.6

In the 1950s, Serratia sp. were commonly associated with pink slime in paper mills,15 but many studies in recent times have shown many different bacteria other than Serratia sp. as the cause of this problem. 3, 4, 6 Interestingly, in one of the mills in the current study, Serratia marcescens was the domi-nant pink- or red-pigmented bacteria found and the cause of pink slime outbreak in that mill (Figures 1 and 2). Possible reasons why Serratia sp. have become rare in recent times have been explored3 and these included changes in machine design and operation, paper making technology, furnish types, biocides, and other additives.

*Study was designed to isolate only pink-or red pigmented bacteria.

Table1. Composition of “pink slime bacteria” from deposits from 6 different mills

Mill 1 (US)

Mill 2 (US)

Mill 3 (Germany)

Mill 4* (Czech Republic)

Mill 5* (China)

Mill 6* (US)

Flectobacillus sp. Runella sp Flectobacillus sp Meiothermus ruber

Serratia marcescens

Flectobacillus major

Ralstonia sp. Sphingomonas sp Caulobacter sp Deionococcus geothermalis

Rhodovarius lipocyclicus

Janthinobacterium sp.

Bacillus cereus Aquaspirillum

Aquitalea sp. Acinetobacter anitratus

Acinetobacter anitratus

Asticcacaulis extrincus

Cytophaga sp Pseudomonas resinovorans

Burkholderia sp. Chromobacterium violaceum

Herbaspirillum sp Klebsiella pneumoniae

Sphingomonas sp. Staphylococcus epidermidis

Uncultured/ Unidentified bacteria

Asticcacaulis extrincus

Uncultured/ Unidentified bacteria

Page 25: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

25PaperAge    JANUARY/FEBRUARY 2014

featurewater treatment

Furthermore, a number of bacteria were isolated and the 16S rRNA gene sequenced but could not be “named” as these bacteria either may not have been fully characterized, or may not have been cultured in the laboratory before. These were designated “uncultured/unidentified.” One inter-esting and unique thing about the use of sequence-based identification in auditing is that the sequences of these “uncultured/unidentified” bacteria can be stored in a search-able database and used in future searches. This database and experience of how to control these bacteria provide a ready tool in the event of pink slime outbreaks. In conclusion, the identification system described in this study was found to be quick, accurate, and less cumbersome than the traditional methods. It allowed a large number of isolates to be identified in a relatively short period of time. The 16S rRNA gene sequences for the organisms are stored in a database which can easily be searched when the need arises. Additionally, the susceptibility of most of these microbes to various control agents have been determined (no data reported in the current work) and this informa-tion, among others, is used in making timely decisions about appropriate control strategies for a particular situation. n

LITERATURE CITED

1 . Ross, R.T., Hollis, C.G. 1976. Microbiological deterioration of pulp-wood, paper and paint. In: Miller, B.M., Litsky, W. (Eds.), Industrial Microbiology. McGraw-Hill, New York, NY, pp. 309-354.

2. Oppong, D., Bryant, S.D., Rangarajan, R., Steele, S. 2006. Application of molecular techniques to identify bacteria isolated from the leather industry. ALCA 101:140-145

3. Oppong, D., King, V.M., Zhou, X., Bowen J. 2000. Cultural and biochemical diversity of pink-pigmented bacteria isolated from

paper mill slimes. J. Ind. Microbiol. Biotechnol. 25:78-80.

4. Oppong, D., King, V.M., Bowen, J. 2003. Isolation and character-ization of filamentous bacteria from paper mill slimes. Internat. Biodeterior. & Biodegrad. 52:53-62.

5. Desjardins, E., Beaulieu, C. 2003. Identification of bacteria con-taminating pulp and a paper machine in a Canadian paper mill. J. Ind. Microbiol. Biotechnol. 30:141-145.

6. Kolari, M., Nuutinen, J., Rainey, FA., Salkinoja-Salonen, T., M.S. 2003 Colored moderately thermophilic bacteria in paper-machine biofilms. J. Ind Microbiol. Biotehcnol. 30:225-238.

7. Suihko, M. L., Sinkko, H., Partanen, L., Mattila-Sandholm, T., Salkinoja-Salonen, M., Raaska, L. 2004. Description of heterotro-phic bacteria occurring in paper mills and paper boards. J. Appl. Microbiol. 97:1228-1235.

8. Mullis, K.B., Faloona, F.A, 1987. Specific synthesis of DNA in vitro via a polymerase chain reaction. Methods Enzymol. 155:335-350.

9. Woese, C. R. 1987. Bacterial Evolution. Microbiol. Rev. 51:221-271.

10. Fox, G. E., Pechman, K. R., Woese, C. R. 1977. Comparative cata-loging of 16S Ribosomal Ribonucleic Acid: Molecular approach to Procaryotic systematics. Int. J. Syst. Bacteriol. 27:44-57.

11. Tracy, T.E., Mulachy, L.S. 1991. A simple method for direct auto-mated sequencing of PCR fragments. Biotechniques 11:68-75

12. Kämpfer P, Busse HJ, Rosséllo-Mora R, Kjellin E, Falsen, E (2004). Rhodovarius lipocyclicus gen. nov. sp. nov., a new genus of the alpha-1 subclass of the Proteobacteria. Syst. Appl. Microbiol. 27:511-516.

13. Lu, S., Lee, J. R., Ryu, S. H., Chung, B. S., Choe, W-S., Jeon, C. O. 2007. Runella defluvii sp. nov., isolated from a domestic wastewater treatment plant. Int J. Syst. Evol. Microbiol. 57:2600-2603.

14. Larkin, J. M., Williams, P. M. 1978. Runella slithyformis gen. nov., sp. nov., a curved non-flexible bacterium. . Int J. Syst. Evol. Microbiol. 28:32-36.

15. Sanborn, J.R. 1951. Relation of red slimes to the general paper mill slime control. TAPPI 34:490-493

David Oppong is Senior Biotechnology Research Scientist, and Tod Stoner is Product Specialist - Deposit Control at Buckman. For further information, please contact David Oppong: [email protected].

Figure 1. Serratia marcescens “red slime.” Figure 2. Serratia marcescens culture.

Page 26: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

26 JANUARY/FEBRUARY 2014 PaperAge

feature

Whether your mill is producing pulp, printing and writ-

ing grades of paper or containerboard, maintaining a

safe work place, complying with applicable laws and

producing profitable products with maximum quality are

all sound objectives for a world-class company. But, what

does it take to accomplish these objectives? To be success-

ful, manufacturers like yourself positively, absolutely, require

maximum equipment availability and productivity of your

paper machines and auxiliary equipment. To make that hap-

pen you need a disciplined, world-class lubrication program.

This can be achieved by establishing some guiding principles

that include:

1. Setting the importance of a lubrication management program.

2. Defining the lubrication management program goals, and...

3. Implementing the tools required to achieve the lubrica-tion management program goals.

THE IMPORTANCE OF A LUBRICATION MANAGEMENT PROGRAM

Most people believe just maintaining or adding lubricant

to the rotating equipment provides effective lubrication.

However, by not implementing lubrication program man-

agement, the opportunity to optimize equipment reliability

and maximize the return on your investment may be lost.

Disciplined lubrication management is the foundation of a

world-class lubrication program. The following chart illus-

trates the difference made in a plant’s total cost of owner-

ship once you’ve taken that step.

Remember that implementing a disciplined lubrication

management program comprises only one part of an overall

equipment reliability improvement program. Sound preven-

tive/predictive maintenance activities combined with good

maintenance planning, scheduling, and execution are also

key to delivering maintenance improvements.

To succeed in today’s fiercely competitive marketplace, pulp and paper manufacturers positively, absolutely, require maximum equipment availability and productivity from their machinery, and a disciplined lubrication management program can make this happen.

reliability maintenance - lubrication

Keep it Running Smooth

By Tom Schiff

Page 27: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

27PaperAge    JANUARY/FEBRUARY 2014

featurereliability maintenance - lubrication

LUBRICATION MANAGEMENT PROGRAM GOALS

To properly define the goals of your

lubrication management program,

use the following list. Choose those

goals that will best meet your com-

pany’s needs:

• Reducelubricantrelatedfailures

• Usethefewestcorrectlubricants

and minimize waste

• Applythelubricantinthecorrect

manner, at the proper time and in

the correct amounts

• Integratetheplant’spreventive

and predictive maintenance goals

into the lubrication program

• Continuallyinvestigateandimple-

ment methods to improve and

achieve the above goals

Once you’ve defined the goals of your lubrication man-

agement program, next you need to be sure you have the

proper tools that will enable you to achieve these goals.

BASIC TOOLS REQUIRED FOR AN EFFECTIVE PROGRAMNo single program works for everyone. There are many dif-

ferent methods to achieve the goals of your lubrication man-

agement program. No matter what method you implement,

to ensure success, you should use the following tools.

Leadership. First and foremost,

lubrication needs to be a priority for

maintenance managers. Many com-

panies look at lubrication on a price

basis and strive for methods to mini-

mize that cost. Unfortunately, when

this happens, you may run the risk of

forfeiting the true payback that can

result from optimizing your lubrica-

tion program — improved equipment

reliability AND decreased overall

maintenance costs. Be sure to nomi-

nate a program champion — someone

who will assume the responsibility,

accountability and control for the

program. Plan for continual improve-

ment and measure your progress on a

regular basis.

A good program requires dedica-

tion, skill and accountability. The discipline to “stick with it”

comes from strong leadership.

Standard Operating Procedures (SOPs). Like other dis-

ciplines (operating or repairing machinery), SOPs can help

guarantee repeatability and quality work. Also, SOPs assist in

the training of lubricators and enable you to track and com-

municate equipment condition.

Teamwork and Communication. A world-class lubrica-

tion program must have a team that works and communi-

cates with all members of the manufacturing group opera-

DESCRIPTION BEFORE AFTER

Annual Lubrication Costs including Labor, Lubricant Costs and Supply Costs $1,055,000 $845,000

Total Annual Maintenance Budget $24,000,000 $22,000,000

Percent Annual Lubrication Costs vs. Total Maintenance Budget 4.4% 3.80%

Lost Annual Availability Due to Scheduled and Unscheduled Maintenance 6% 2%

Estimated Annual Profit Lost Due to Lost Equipment Reliability $3,500,000 $1,200,000

Annual Maintenance Department Overtime 22% 14%

Annual Number of Equipment Failures Due to Poor Lubrication 18 2

Annual Volume of Lubricant Consumed (gallons) 62,000 15,000

Most people mistakenly believe just maintaining or adding lubricant

to the rotating equipment provides effective lubrication.

Note: Table shows example numbers for demonstration purpose only.

Page 28: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

28 JANUARY/FEBRUARY 2014 PaperAge

reliability maintenance - lubrication

tions, maintenance,

purchasing, planning

and engineering. The

team champion is key

is maintaining the com-

munication and keep-

ing the team focused.

Lubrication

Scheduling, Planning,

and Tracking Manage-

ment Systems.

To handle the quantity

of data encountered

(even for a small plant),

an effective computer-

ized system should be

employed. Without

the aid of computer-

ized data management,

important equipment trends may be missed and/or docu-

mentation of the lubrication program may be lacking.

Training. To continually improve, both program leader

and lubricators must continually learn best lubrication

practices, as well as learn new techniques in their specific

discipline.

Metrics. Knowing the past performance and understand-

ing the effects of program efforts enable you to make and

evaluate lubrication program -related decisions. The follow-

ing metrics are useful when tracking your program’s progress

(other metrics not listed below may also prove useful).

• Totalmaintenancecostsandpercentspentonlubrication

• Percentofequipmentscheduledandunscheduled

downtime

• Numberoflubricantrelatedfailures

• Percentofmaintenanceovertimelabor

• Lubricantconsumption

• SafetyIncidents

Audits. In order to improve, you need to validate or

audit your lubrication program. Whether performed inter-

nally or by a third party, the effort to benchmark and

evaluate your lubrication program against other “best in

class” operations will supply tremendous dividends. The

science of lubrication

audits can become very

involved, however, and

deserves a paper of its

own.

CONCLUSION

Safety, compliance,

and maximum qual-

ity manufacturing are

sound objectives for a

world-class company. A

disciplined lubrication

management program

is what’s needed to

achieve these objec-

tives. And, when you

set goals that put in

place the tools you

need to succeed, you are well on your way to establishing a

world-class lubrication program. n

Tom Schiff is Americas Field Engineering Manager for Exxon Mobil Corporation. He has nearly 20 years of experience with ExxonMobil and for 8 years has held the positions of Reliability Engineer and Maintenance Superintendent for a prominent paper producer. For further information about lubrication management, please visit: www.mobilindustrial.com/ind/english/contactus.aspx.

To continually improve, both program leader and lubricators must continually learn best lubrication practices, as well

as learn new techniques in their specific discipline.

Page 29: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

29PaperAge    JANUARY/FEBRUARY 2014

classified

HAVE HEADBOX ISSUES? Not getting answers? Edwin X. Graf, A.P.M., LLC

• 30+ years experience with major builders of both Hydraulic and Roll Headboxes

• Negotiated Rates

Cell: (920) 915-1845 email: [email protected]

Take out a classified ad and

reach thousands of paper industry

readers.

We set up your ad free of charge.

Contact Mike O’Brien: 781-923-1016, or

email: [email protected]

Hydro-FloTM SystemsHydro-FloTM Deckle Edge Control Systems

Get the EDGE over your competition! Maximize your products potential and improve machine runnability

Call today to schedule a mill visit to discussHydro-FloTM Systems for your machine

*NO Wire Contact *Very low maintenance *Easy adjustment *Improves profiles *Excellent sheet transistion

001(989)695 2646 www.Papermachine.com

Celebrating Our 40th Anniversary

Serving the Paper Industry for over 40 years! ISO 9001:2008 Certified

Quality Paper Machinery with Reliable Service Providing Roll Services and Engineering Services

Overpeck, Ohio (30 miles North of Cincinnati) Phone: 513-863-6707 ⋄ Fax: 513-863-8009 Website: http://www.miamimachine.com

Email: [email protected]

index of advertisers COMPANY Page WEBSITE

Aldon Company 17 www.aldonco.com

Edwin X. Graf 29 [email protected]

Miami Machine Corp. 29 www.miamimachine.com

Paper2014 31 www.paper2014.com

PaperCon 2 www.papercon.org

Papermachine Service Industries 29 www.papermachine.com

Souhegan Wood Products 13 www.souheganwood,com

Thiele Kaolin Company 5 www.thielekaolin.com

Valmet 32 www.valmet.com

Page 30: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

30 JANUARY/FEBRUARY 2014 PaperAge

Continuous Commitment to Paper Recovery for Recycling

recycling matters

Paper recovery has fostered a dynamic marketplace that allows recovered fiber to find its highest-value use, which helps to encourage even more recycling.

Recovering paper and paper-based products for recycling has long been a priority for our industry and an effort in which AF&PA members continue to be proven leaders. Since 1990, when we first set a nationwide paper recovery goal, the U.S. recovery rate has nearly doubled, topping 65 per-cent in 2012. According to the U.S. Environmental Protection Agency, in 2011, only 27.6 percent of glass, 20.7 percent of aluminum and 8.3 percent of plastics were recovered from municipal solid waste streams. Recovering paper products extends the fiber supply, which allows our industry to reuse its products to make new ones. It also saves an average of 3.3 cubic yards of landfill space for each ton of paper recycled. AF&PA member companies have taken efforts to develop and nurture a voluntary, market-driven system that fosters consistently high rates of paper recovery. Our sustainability initiative — Better Practices, Better Planet 2020 — includes a goal to exceed 70 percent recovery of all paper used in the U.S. by the year 2020. Our members continually take strides to improve the recovery of paper and paper-based packaging. The paper recycling industry collects, sorts and processes recovered paper into new paper and paper-based packaging products that were valued at $8.4 billion in 2012. And the value of U.S. recovered paper exports totaled $3.5 billion in 2012. All in all, paper recovery has fostered a dynamic market-place that allows recovered fiber to find its highest-value use, which helps to encourage even more recycling. But paper recovery for recycling is a collective effort. Ultimately, it is possible and successful thanks to the commit-ment of millions of Americans who make the effort to recycle at home, work and school every day. We recognize excellence in paper recovery for recycling through our annual AF&PA Recycling Awards program. First launched in 2006, the AF&PA Recycling Awards recognize and highlight businesses, schools and communities that increase paper recovery through educational, innova-

tive and cost-effective programs and partnerships. The program generates interest in developing new recycling programs; provides a resource to those looking to start or improve paper recovery programs; and supports the industry’s on-going effort to increase recovery and maintain the quality of recyclable paper. Now in its ninth year, the AF&PA Recycling awards program has been redesigned and continues to provide great visibility and reward those engaged in successful paper recycling efforts.

In each category — school, business and community —there are now four chances to win. Programs will no longer be judged for their all-over performance, but on specific characteristics, namely: volume – the total amount of paper and paperboard collected; creativity – unique and innovative ways that have been used to market the program, raise awareness and generate interest; participation – unique and innovative ways success-ful programs increased participation and tonnage collected; and partnerships – innovative partnerships with communities, businesses and/or non-profit organizations used to promote increased recovery. This structure will allow for a greater focus on elements that drive improved paper recovery program performance and increase recovery overall. It will also allow us to expand our reach and provide opportunities for more parties to engage and enter the program. Descriptions of the awards, entry criteria and entry forms are all available on paperrecycles.org. The deadline for all entries is March 7, 2014. Our industry has a proud tradition of achievement in paper recovery for recycling, and we are looking forward to recog-nizing the invaluable involvement of businesses, schools and communities in making paper recycling a success. Paper offers a recyclable product made from a renewable resource, which is one of many strong points that makes paper the choice that consumers can trust and be proud to use. n

By Donna Harman, President and CEO, American Forest & Paper Association

The paper recycling industry collects, sorts and processes recovered paper into new

paper and paper-based packaging products that were valued at $8.4 billion in 2012.

Page 31: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

co-hosted by

Experience the Paper Industry’s Premier EventHELD AT THE NEW YORK PALACE IN MIDTOWN NYC

Industry Leadership Panel featuring:

John Williams President & CEO of DomtarDante Parrini Chairman & CEO of GlatfelterJack Sanders President & CEO of SonocoJohn Rooney President & CEO of Evergreen PackagingDavid McGehee President of MacPapers

Paper2014 Luncheon keynote speaker: Alex Sheen Founder of Because I Said I Would

Early bird registration closes February 28. Register today at Paper2014.com

Page 32: DRYER SECTION PERFORMANCE - PaperAge | pulp and paper ... · PDF fileJANUARY/FEBRUARY 2014 CONTAINERBOARD Capacity bulge, sluggish demand remain challenges for containerboard market

Discover more at www.valmet.com

Valmet Corporation is now an independent, listed company that was reborn through the demerger of the pulp, paper and power businesses from Metso Group in December 2013. We develop and supply competitive services and technologies for the pulp, paper and energy industries.

Valmet’s services cover everything from maintenance outsourcing to mill and plant improvements and spare parts. Our strong technology offering includes entire pulp mills, tissue, board and paper production lines, as well as power plants for bio-energy production. Valmet and Metso will continue to work closely together to offer winning automation solutions.

Our 11,000 professionals around the world work close to our customers and are committed to moving our customers’ performance forward – every day.

Committed to moving our customers’ performance forward – every day