空気環境測定器ビルフローBKM-504„測定部仕様（BKM-504,LD-5R,510 11,NL-27,BKM-GT,XP-308B） 項 目 測定原理 測定範囲 最小目盛 測定精度 温 度 湿
DRJ240-24-1 EVALUATION DATA - TDK Product …...DRJ240-24-1 1. 測定方法 Evaluation Method1.1...
21
DRJ240-24-1 EVALUATION DATA 型式データ TDK-Lambda
Transcript of DRJ240-24-1 EVALUATION DATA - TDK Product …...DRJ240-24-1 1. 測定方法 Evaluation Method1.1...
DRJ240-24-1
EVALUATION DATA
型式データ
TDK-Lambda
DRJ240-24-1
INDEX
1. 測定方法 Evaluation Method PAGE
1.1 測定回路 Circuit used for determination
測定回路1 Circuit 1 used for determination .............................................................................................................…T-1
静特性 Steady state data
過電流保護特性 Over current protection (OCP) characteristics
過電圧保護特性 Over voltage protection (OVP) characteristics
出力立ち上がり特性 Output rise characteristics
出力立ち下がり特性 Output fall characteristics
出力保持時間特性 Hold up time characteristics
入力電圧瞬停特性 Response to brown out characteristics
高調波成分 Input current harmonics
入力電流波形 Input current waveform
測定回路2 Circuit 2 used for determination ..................................................................................................................... T-1
過渡応答（負荷急変）特性 Dynamic load response characteristics
測定回路3 Circuit 3 used for determination .................................................................................................................... T-2
入力サージ電流（突入電流）波形 Inrush current waveform
測定回路4 Circuit 4 used for determination ..................................................................................................................... T-2
リーク電流特性 Leakage current characteristics
測定回路5 Circuit 5 used for determination ..................................................................................................................... T-2
出力リップル、ノイズ波形 Output ripple and noise waveform
測定構成 Configuration used for determination ........................................................................................................................… T-3
EMI特性 Electro-Magnetic Interference characteristics
(a) 雑音端子電圧 （帰還ノイズ） Conducted Emission
(b) 雑音電界強度 （放射ノイズ） Radiated Emission
1.2 使用測定機器 List of equipment used ....................................................................................................................................…T-4
TDK-Lambda
DRJ240-24-1
2. 特性データ Characteristics
2.1 静特性 Steady state data
(1) 入力・負荷・温度変動／出力起動・遮断電圧
Regulation - line and load, Temperature drift / Start up voltage and Drop out voltage ..................................................................................T-5
(2) 効率対出力電流 Efficiency vs. Output current ........................................................................................................…............................T-6
(3) 入力電流対出力電流 Input current vs. Output current ...............................................................................…........................T-7
(4) 入力電力対出力電流 Input power vs. Output current ...............................................................................…........................T-7
2.2 過電流保護特性 Over current protection (OCP) characteristics ...........................................................................................................T-8
2.3 過電圧保護特性 Over voltage protection (OVP) characteristics ................................................................................... T-8
2.4 出力立ち上がり特性 Output rise characteristics ...................................................................……...……......................................…..… T-9
2.5 出力立ち下がり特性 Output fall characteristics .............................................................................................................................…T-9
2.6 出力保持時間特性 Hold up time characteristics ...................................................................................................................................T-10
2.7 過渡応答（負荷急変）特性 Dynamic load response characteristics ....................................................…............................. T-11
2.8 入力電圧瞬停特性 Response to brown out characteristics .......................................................................................... T-12
2.9 入力サージ電流（突入電流）波形 Inrush current waveform ......................................................................................................… T-13
2.10 高調波成分 Input current harmonics ...............................................................................................................................................................................................…T-14
2.11 入力電流波形 Input current waveform ......................................................................................................................................................................................................................…T-14
2.12 リーク電流特性 Leakage current characteristics ............................................................................................................ T-15
2.13 出力リップル、ノイズ波形 Output ripple and noise waveform ............................................................................ T-16
2.14 EMI特性 Electro-Magnetic Interference characteristics ......................................................................................................................................................... T-17, 18
使用記号 Terminology used
定義 Definition
Vin ......... 入力電圧 Input voltage
Vout ......... 出力電圧 Output voltage
Iin ......... 入力電流 Input current
Iout ......... 出力電流 Output current
Ta ......... 周囲温度 Ambient temperature
f ......... 周波数 Frequency
※ 当社測定条件における結果であり、参考値としてお考え願います。
Test results are reference data based on our measurement condition.
TDK-Lambda
DRJ240-24-1
1. 測定方法 Evaluation Method
1.1 測定回路 Circuit used for determination
測定回路1 Circuit 1 used for determination
・静特性 Steady state data
・過電流保護特性 Over current protection (OCP) characteristics
・過電圧保護特性 Over voltage protection (OVP) characteristics
・出力立ち上がり特性 Output rise characteristics
・出力立ち下がり特性 Output fall characteristics
・出力保持時間特性 Hold up time characteristics
・入力電圧瞬停特性 Response to brown out characteristics
・高調波成分 Input current harmonics
・入力電流波形 Input current waveform
測定回路2 Circuit 2 used for determination
・過渡応答 （負荷急変） 特性 Dynamic load response characteristics
AC Power
supply
A W
V
AC
AC
P.S.
V
V
+V
-V
Shunt res.
Load
Digital power meter
SW
Current probe
Controlled temp. chamber
tr tf
75%
70%
Output current waveform
Iout 25% <==> 75%
30%
25%
Min
AC Power
supply
A W
V
AC
AC
P.S.
Load 1
Load 2
V
V
+V
-V
Shunt res.
Dynamic dummy load
Digital power meter
SW
Current probe
TDK-Lambda T-1
DRJ240-24-1
測定回路3 Circuit 3 used for determination
・入力サージ電流 （突入電流） 波形 Inrush current waveform
測定回路4 Circuit 4 used for determination
・リーク電流特性 Leakage current characteristics
測定回路5 Circuit 5 used for determination
・出力リップル、ノイズ波形 Output ripple and noise waveform
A W
V
AC
AC
P.S.
V
V
+V
-V
Shunt res.
Load
Digital power meter
Current probe
AC Power
supply
Digital power meter
V
V V
W AC
AC
P.S.
+V
-V
Shunt res.
Load
AC Power
supply
A
Slide Reg.
Leakage current meter
SW
SW
Oscilloscope
Bandwith : 20MHz
AC Power
supply
A W
V
AC
AC
P.S.
+V
-V
Load
SW
C1 : 0.1uF Film cap.
C2 : 47uF Elect cap.
Coaxial cable
1.5m 50Ω
300mm
+
C1 C2
Digital power meter
TDK-Lambda T-2
DRJ240-24-1
測定構成 Configuration used for determination
・EMI特性 Electro-Magnetic Interference characteristics
(a) 雑音端子電圧 (帰還ノイズ）Conducted Emission
(b) 雑音電界強度 (放射ノイズ）Radiated Emission
水平大地面 Horizontal ground plane
垂直基準大地面
(2m × 2m)
Vertical ground
reference plane D=40cm 擬似電源回路網 AMN 50Ω/50uH
EMI Test receiver
spectrum analyzer
供試機器 D.U.T.
D=80cm
H=80cm 台 Stand
入力電源 AC Power supply
電源ケーブル Power cable
DINレール取付治具 DIN rail installation fixture
アルミ板
Aluminum plate
供試機器 D.U.T.
アンテナAntenna
EMI Test receiver
spectrum analyzer
pre amp.
水平大地面 Horizontal ground plane
D=10m
H=80cm 台 Stand
入力電源 AC Power supply
ターンテーブル Turn table
電源ケーブル Power cable
DINレール取付治具 DIN rail installation fixture
アルミ板
Aluminum plate
TDK-Lambda T-3
DRJ240-24-1
1.2 使用測定機器 List of equipment used
EQUIPMENT USED MANUFACTURER MODEL NO.
1 DIGITAL STORAGE OSCILLOSCOPE YOKOGAWA DL1740/DL1740E
2 DIGITAL MULTIMETER AGILENT 34970A
3 DIGITAL POWER METER HIOKI 3333
4 CURRENT PROBE/AMPLIFIER YOKOGAWA 701931
5 DATA ACQUISITION UNIT AGILENT 34970A
6 ELECTRONIC LOAD CHROMA 63112A
7 CONTROLLED TEMP. CHAMBER ESPEC SH-641
8 LEAKAGE CURRENT METER SIMPSON 228
9 AC SOURCE CHROMA 61505
10 AC SOURCE (CE-UL Lab) KEYSIGHT TECHNOLOGIES 6813B
11 EMI TEST RECEIVER (CE-UL Lab) ROHDE & SCHWARZ ES17
12 LISN (CE-UL Lab) SCHAFFNER LISN NNB 41
13 LISN (CE-UL Lab) EMCO LISN (AE) 3825/2
14 EMI TEST RECEIVER (RE-UL Lab) ROHDE & SCHWARZ 100Hz-26.5Ghz ESU26
15 ANTENNA (BILOG) (RE-UL Lab) TESEQ CBL6112B
16 ANTENNA (HORN) (RE-UL Lab) EMCO 3115
17 PRE AMP (RE-UL Lab) HP 8447D
18 PRE AMP (RE-UL Lab) TOYO TPA0108-40
TDK-Lambda T-4
DRJ240-24-1
2. 特性データ Characteristics
2.1 静特性 Steady state data
(1) 入力・負荷・温度変動／出力起動・遮断電圧Regulation - line and load, Temperature drift / Start up voltage and Drop out voltage
1. Regulation - line and load Condition Ta :
Iout \ Vin 85VAC 115VAC 230VAC 264VAC line regulation
0% 24.101 24.101 24.101 24.101 0mV
50% 24.065 24.065 24.065 24.064 1mV
100% 24.032 24.032 24.031 24.031 1mV
69mV 69mV 70mV 70mV
0.287% 0.287% 0.292% 0.292%
2. Temperature drift Condition Vin :
Iout :
Ta -25°C 25°C 55°C temperature stability
Vout 23.951V 24.032V 24.042V 91mV 0.379%
3. Start up voltage and Drop out voltage Condition Ta :
Iout :
Start up voltage (Vin) 80VAC
Drop out voltage (Vin) 61VAC
24V
load
regulation
100%
0.000%
0.004%
0.004%
25°C
115VAC
100%
25°C
TDK-Lambda T-5
DRJ240-24-1
(2) 効率対出力電流Efficiency vs. Output current Conditions Vin :
:
:
:
Ta :
24V
115
230
264
25°C
85VAC
115VAC
230VAC
264VAC
70
80
90
100
0 20 40 60 80 100
Eff
icie
ncy
(%
)
Output current (%)
TDK-Lambda T-6
DRJ240-24-1
(3) 入力電流対出力電流Input current vs. Output current Conditions Vin : 85VAC
: 115VAC
: 230VAC
: 264VAC
Ta :
24V
85VAC
115VAC
230VAC
264VAC
(4) 入力電力対出力電流Input power vs. Output current Conditions Vin : 85VAC
: 115VAC
: 230VAC
: 264VAC
Ta : 25°C
24V
85VAC
115VAC
230VAC
264VAC
Vin
Vin
25°C
0.014A
0.016A
Input current
Iout : 0%
0.071A
0.081A
1.68W
1.64W
1.60W
1.58W
Input power
Iout : 0%
0.0
1.0
2.0
3.0
4.0
0 20 40 60 80 100
Inp
ut
curr
ent
(A)
Output current (%)
0
100
200
300
0 20 40 60 80 100
Input
pow
er (
W)
Output current (%)
TDK-Lambda T-7
DRJ240-24-1
2.2 過電流保護特性 Over current protection (OCP) characteristics Conditions Vin : 115VAC
Ta : -25°C
25°C
24V 55°C
2.3 過電圧保護特性 Over voltage protection (OVP) characteristics Conditions Vin : 115VAC
Iout : 0%
Ta : 25°C
24V
10V/DIV 50s/DIV
0
5
10
15
20
25
0 50 100 150 200
Ou
tpu
t vo
ltag
e (V
)
…
Output current (%)
OVP Point
0V →
Vout →
TDK-Lambda T-8
DRJ240-24-1
2.4 出力立ち上がり特性Output rise characteristics Conditions Vin : (A)
: (B)
: (C)
: (D)
Ta :
24V Iout : 0% Iout : 100%
10V/DIV 200ms/DIV 10V/DIV 200ms/DIV
2.5 出力立ち下がり特性Output fall characteristics Conditions Vin : (A)
: (B)
: (C)
: (D)
Ta :
24V Iout : 0% Iout : 100%
10V/DIV 50s/DIV 10V/DIV 50ms/DIV
25°C
85VAC
115VAC
230VAC
264VAC
25°C
85VAC
115VAC
230VAC
264VAC
← Vin →
← 0V →
← Vout →
DC B A DC B A
← Vin →
← 0V
← Vout →
ABCD ABCD
TDK-Lambda T-9
DRJ240-24-1
2.6 出力保持時間特性Hold up time characteristics Conditions Vin :
Ta :
24V
115VAC
230VAC
25°C
10
100
1000
0 20 40 60 80 100
Hold
up t
ime
(ms)
Output current (%)
TDK-Lambda T-10
DRJ240-24-1
2.7 過渡応答（負荷急変）特性Dynamic load response characteristics Conditions Vin :
Iout :
(tr = tf = 50us)
Ta :
f = 100Hz f = 1kHz
0.5V/DIV 2ms/DIV+0.43% -0.43% +0.43% -0.43%
200μs/DIV
115VAC
24V
25% 75%
25°C
0.5V/DIV
← Iout:0% →
← Vout →
← Iout →
TDK-Lambda T-11
DRJ240-24-1
2.8 入力電圧瞬停特性Response to brown out characteristics Conditions Vin :
Iout :
Ta :
A = 23ms
B = 34ms
C = 35ms
10V/DIV 50ms/DIV
Conditions Vin :
Iout :
Ta :
A = 27ms
B = 54ms
C = 55ms
10V/DIV 50ms/DIV
25°C
24V
100%
115VAC
100%
25°C
24V
230VAC
A B C
A B C
TDK-Lambda T-12
DRJ240-24-1
2.9 入力サージ電流（突入電流）波形Inrush current waveform
24V
Conditions Vin :
Iout :
Ta :
20A/DIV 200ms/DIV 20A/DIV 200ms/DIV
Conditions Vin :
Iout :
Ta :
20A/DIV 200ms/DIV 20A/DIV 200ms/DIV
100%
115VAC
100%
230VAC
25°C
25°C
Switch on phase angle of input AC voltage φ = 0°
Switch on phase angle of input AC voltage φ = 90°
Switch on phase angle of input AC voltage φ = 0°
Switch on phase angle of input AC voltage φ = 90°
← Iin →
← Vin →
← Iin →
← Vin →
TDK-Lambda T-13
DRJ240-24-1
2.10 高調波成分Input current harmonics Conditions Iout :
Ta :
24V Vin :
2.11入力電流波形Input current waveform Conditions Iout : 100%
Ta : 25°C
Vin : 115VAC Vin :
2A/DIV 5ms/DIV 2A/DIV 5ms/DIV
100%
25°C
115VAC
230VAC
0.001
0.010
0.100
1.000
10.000
1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39
Har
mo
nic
cu
rren
t (A
)
Harmonic Order
IEC61000-3-2 Limit (class A)
←Iin→
←Vin→
TDK-Lambda T-14
DRJ240-24-1
2.12 リーク電流特性Leakage current characteristics Conditions Iout :
Ta :
24V
f :
f : 60Hz
0% --------
100%
25°C
50Hz
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
80 120 160 200 240 280
Lea
kag
e cu
rren
t (m
A)
Input voltage (VAC)
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
80 120 160 200 240 280
Lea
kag
e cu
rren
t (m
A)
Input voltage (VAC)
TDK-Lambda T-15
DRJ240-24-1
2.13 出力リップル、ノイズ波形Output ripple and noise waveform Conditions Vin :
Iout :
Ta :
20mV/DIV 5ms/DIV
Conditions Vin : Iout :
Ta :
20mV/DIV 5ms/DIV
25°C
115VAC0%
24V
24V
115VAC100%
25°C
TDK-Lambda T-16
DRJ240-24-1
2.14 ＥＭＩ特性Electro-Magnetic Interference characteristics Conditions Vin : 230VAC
Iout :
Ta : 25°C
雑音端子電圧Conducted Emission
24VQP spectrum waveform :
AV spectrum waveform :
Phase : L
Ref. Limit Measure
Data (dBuV) (dBuV)
QP 54.8 44.6
AV 41.5 31.3
QP spectrum waveform :
AV spectrum waveform :
Phase : N
Ref. Limit Measure
Data (dBuV) (dBuV)
QP 49.2 38.9
AV 32.6 22.3
EN55011B,EN55032B,FCCBの限界値はVCCI class Bの限界値と同じ
Limit of EN55011B,EN55032B,FCCB are same as its VCCI class B.
100%
(1.17MHz)
Point A
(0.26MHz)
Point B
EN55032-B
AV Limit
EN55032-B
QP Limit
A
B
EN55032-B
AV Limit
EN55032-B
QP Limit
TDK-Lambda T-17
DRJ240-24-1
雑音電界強度Conditions Vin :
Iout :
Ta : 25°C
24V Horizontal :
Vertical :
EN55011B,EN55032Bの限界値はVCCI class Bの限界値と同じ
Limit of EN55011B,EN55032B are same as its VCCI class B.
表示はピーク値
Indication is peak values.
230VAC
100%
Radiated Emission
EN55032-B
QP Limit
TDK-Lambda T-18
