Driver Test SOP
-
Upload
yenri-febri -
Category
Documents
-
view
607 -
download
4
Transcript of Driver Test SOP
Drive Test SOP
Drive Test SOP
Revision History
Date Version Issued By Approved By Changes
01/31/2005 0.1 JUAN Original
Drive Test SOP
How To:
Drive Test Using TEMS Investigation GSM
I. Starting TEMS
First, make sure TEMS investigation GSM is already installed
1.1 Start TEMS from Start Menu
1.2 This is TEMS investigation GSM user interface
Drive Test SOP
II. Connect Devices
First, make sure all devices are already connected to the laptop.
II.1Before we start, we must identify equipment first. Click the Identify Equipment
button on the Equipment Control toolbar.
A dialog named "Port Properties" will appear
make sure that mobile station and GPS is connected to a COM port on your
computer and the COM port you use is checked. Than Click OK
II.2TEMS Investigation now scans the COM ports for external devices and enables
these devices automatically. A Port Configuration window is opened (if not open,
you can look at configuration tab), showing the progress of the scan. When it is
finished (after a few seconds), the text "Ready" is displayed at the bottom of the
Port Configuration. Red circle in the icons means the device is not yet connected.
Drive Test SOP
If automatic identify can’t find your equipment, you can add them manually:
Choose your Port and Equipment, and click “OK”:
II.3To receive data from the mobile and GPS, you must connect those devices:
Click “Connect All” on the Connections Toolbar.
If the connection is successful, then red circle in the icon will change into
green circle.
II.4If you want to disconnect the device, just click “Disconnect all” from the
Toolbar:
Drive Test SOP
III. Recording
Before start recording, you should open maps (or GeoSet) and cell definition
III.1 Open Map
You can view map window in the Map worksheet above the status bar.
In the Map Window you’ll see map toolbar. To open Map, click “Open map”
Locate and select your Map Files and click open:
or for fast layering, you can open “GeoSet” instead :
III.2 Open Cell Definition
From Menu Bar, click Configuration, and click Cell Definition :
than Cell Definition window is shown. Click “Open”
Drive Test SOP
Locate and select your Cell Name Files (*.cel) and click open:
III.3 Start Recording
You can start recording by clicking Record Button on the toolbar
Then you’ll be ask name of log file and where to save it.
Drive Test SOP
III.4 Stop Recording
If you want to stop recording, just click Stop button on the toolbar:
III.5 Replay Log File
If you want to replay your log file (or to make sure you’ve recorded well),
click “Open logfile” on the tool bar :
Warning: You can replay Log file only if your devices is disconnected
Drive Test SOP
IV. Testing Mode
4.1 Idle Mode
In idle mode, the mobile station is standby and not making any call. You can
just click record button to start recording idle mode. Use Idle Mode to test
sectorization and cross feeder on the night of cut over.
4.2 Idle Lock and Idle Prevent
When the mobile station is in idle mode, it can be locked to one channel or to
a set of channels. This inhibits all reselections to other channels, regardless of the
signal strength and quality of neighboring cells. The inverted operation is also
possible, namely to prevent reselection to a specified channel set.
Click
on the toolbar, and select which channel you want to lock
To reset the lock on channel function, simply click
on the toolbar.
There is another way to lock on channel, by using Equipment Properties :
Click
on the toolbar.
Drive Test SOP
To prevent reselection to a specified channel set, just choose Prevent Function :
4.3 Dedicated Mode
In dedicated mode, the mobile station is making a call. You can do it by either using the TEMS mobile phone, or click redial
on the toolbar
.
To terminate an ongoing call, simply click
on the toolbar
Drive Test SOP
4.4 Force Handover and Prevent Handover
When the mobile station is in dedicated mode, you can manipulate handovers. Specifically, you can do one of the following:
Prevent handover to specified channels. The mobile then reports no signal strength for these channels.
Force handover to a specified channel, or restrict handovers to a chosen channel set. The mobile then reports a RxLev of 63 for any such cell, 10 for the serving cell and no RxLev for other neighboring cells.
Click
(Equipment Properties) on the toolbar
To Force handover, simply select “Target HO” Function, and choose target channels.
To Prevent handover, simply select “Prevent HO” Function, and choose target channels.
Drive Test SOP
4.5 Command Sequence
Command sequences are used to automate testing of voice as well as data. They
allow you to prerecord all the commands to be given to the mobile stations during a
drive test. Use command sequence for NQI drive test.
Go to menu bar, click “Control” and than click “Command Sequence”:
If you’ve created Command Sequence before, just open the file:
Drive Test SOP
4.6 GPRS Test
Before doing GPRS test, your mobile phone has to be configured based on operator parameter. Example of manual configuration is presented on Appendix 1.
To start Testing, press Record, Browse using WAP browser on the mobile phone. Wait until you hear “GPRS attached” and “PDP context activated”. Start browsing for a few second, and than close your wap browser. You will hear “GPRS Detached”. You may click Stop to stop recording.
Drive Test SOP
V. Exporting Log File
To process log file data to other software (e.g MapInfo), you have to export the logfile first. Go to Menu Bar, click “Logfile” and than click “Export Logfile”
On the Export Logfile Window, click “Add order”
For Example, we export logfiles into MapInfo Tab file. Click “Setup…”
Drive Test SOP
Choose the Information Element (IE) you want to export. Usually we choose “RxLev Sub (dBm)”, “RxQual Sub” and “SQI”
Go to “Options Tab”. If you want, you can check “Include file name in file”. Than
click “OK”
Drive Test SOP
After finishing setup, fill all the inputs in the “Add Export Order” window, and than click “OK” :
Than click “Start” to start exporting logfiles.
Drive Test SOP
APPENDIX 1.Manual Configuration WAP over GPRS on T68 Mobile Phone for Telkomsel
Just follow these steps below :
Use this Parameter : APN : telkomsel, User id: wap, Password : wap123
Drive Test SOP
Use : IP Address : 10.1.89.130, user id = wap, Password = wap123, Security= Off, Show Pictures = On, Response Timer=150 seconds.
Drive Test SOP
Start Browsing :
Drive Test SOP
APPENDIX 2.
Tools Needed:1. Power Inverter
2. GPS (with data cable)
3. TEMS Handset (with data cable)
4. Laptop with TEMS software installed
Drive Test SOP
5. Dual Serial I/O PC Card (If needed)
Drive Test SOP