Drilling machine of gabriel
-
Upload
amber-anderson -
Category
Documents
-
view
226 -
download
2
Transcript of Drilling machine of gabriel
-
8/10/2019 Drilling machine of gabriel
1/27
Drilling Machine
-
8/10/2019 Drilling machine of gabriel
2/27
Drilling
Drilling is the operation of producing circular hole in thework-piece by using a rotating cutter called DRILL.
The achine used for drilling is called drilling achine.
The drilling operation can also be accoplished in lathin which the drill is held in tailstock and the work is held
by the chuck.
The ost coon drill used is the twist drill.
-
8/10/2019 Drilling machine of gabriel
3/27
Drilling Machine
It is the siplest and accurate achine used inproduction shop.
The work piece is held stationary ie. "laped in
position and the drill rotates to ake a hole.
Types #-Types #-
a$ %ased on construction#&ortable! 'ensiti(e!Radial! up-right! )ang!Multi-spindle
b$%ased on *eed#
+and and &ower dri(en
-
8/10/2019 Drilling machine of gabriel
4/27
'ensiti(e Drilling Machine Drill holes
fro ,. to,
peratorsenses thecutting actionso sensiti(edrillingachine
-
8/10/2019 Drilling machine of gabriel
5/27
/p-Right Drilling Machine
Drill holesupto
0
Table cano(e(erticallyandradially
-
8/10/2019 Drilling machine of gabriel
6/27
Radial Drilling Machine
It the largestand ost(ersatile
used frodrillingediu tolarge andhea(y workpieces.
-
8/10/2019 Drilling machine of gabriel
7/27
-
8/10/2019 Drilling machine of gabriel
8/27
Drill MaterialsThe two ost coon types are
,. +'' drill
- Low cost
1. "arbide- tipped drills
- high production and in "2" achines
ther types are'olid "arbide drill! Ti2 coated drills! carbide
coated asonry drills! parabolic drills! split point
drill
-
8/10/2019 Drilling machine of gabriel
9/27
Drilling And Drills
Types of drills
3 Twist drill# ostcoon drill
3 'tep drill#produces holesof two or oredifferentdiaeters
3 "ore drill# usedto ake an
e4isting holebigger
-
8/10/2019 Drilling machine of gabriel
10/27
Drill fi4ed to the spindle
Drilling operationsDrilling operations
Drilling Centre Hole
Drilling Deep Holes
Drilling ThinMaterial
Drilling Pilot Hole
-
8/10/2019 Drilling machine of gabriel
11/27
Tool 2oenclature
-
8/10/2019 Drilling machine of gabriel
12/27
Tool +olding de(ices The different ethods used for holding
drill in a drill spindle are
%y directly fitting in the spindle hole.
%y using drill slee(e
%y using drill socket
%y using drill chuck
-
8/10/2019 Drilling machine of gabriel
13/27
5ork +olding De(ices
-
8/10/2019 Drilling machine of gabriel
14/27
Drilling operations perations that can be perfored in a
drillin g achine are
Drilling Reaing
%oring
"ounter boring "ountersinking
Tapping
-
8/10/2019 Drilling machine of gabriel
15/27
perations in drilling achine
-
8/10/2019 Drilling machine of gabriel
16/27
perations in drilling achine
-
8/10/2019 Drilling machine of gabriel
17/27
Types of cuttersReaers #-
Multi tooth cutting tool
6ccurate way of si7ing and finishing the pre-e4isting hole.
6ccuracy of 0.00 can be achie(ed
%oring Tool#-
'ingle point cutting tool.
%oring tool is held in the boring bar which hasthe shank.
6ccuracy of 0.00 can be achie(ed.
-
8/10/2019 Drilling machine of gabriel
18/27
Types of cutters"ountersinks #-
'pecial angled cone shaped enlargeent at
the end of the hole
"utting edges at the end of conical surface.
"one angles of 809! :19! ;09! ,009! ,,09! ,109
"ounter %ore Tool#-'pecial cutters uses a pilot to guide the cutting
action .
6ccoodates the heads of bolts.
-
8/10/2019 Drilling machine of gabriel
19/27
"ounter bore and spot facing
-
8/10/2019 Drilling machine of gabriel
20/27
Types of cutters
"obined "ountersinks and central drill #-
'pecial drilling tool to start the hole accurately.
6t the end it akes countersinks in the work
piece.
)un drill #-
Machining of lengthy holes with less feed rates.To o(ercoe the heating and short life of the
noral drill tool
-
8/10/2019 Drilling machine of gabriel
21/27
Types of cutters
Tapping#-
*or cutting internal thread
Multi cutting edge tool.
Tapping is perfored
either by hand or by
achine.
Minor dia of the thread isdrilled and then tapping is
done.
-
8/10/2019 Drilling machine of gabriel
22/27
5ork +olding De(ices ,. Machine Table
-
8/10/2019 Drilling machine of gabriel
23/27
'tep %locks
"laps
-
8/10/2019 Drilling machine of gabriel
24/27
Definitions
"utting 'peed >($#-It?s the peripheral speed of the drill( @ ADA2 where
D @ dia of the drill in
2 @ 'peed of rotation in rp
*eed Rate >f$#-
It?s the o(eent of drill along the a4is >rp$
Depth of "ut >d$#-The distance fro the achined surface to the drilla4is
d @ D B 1
-
8/10/2019 Drilling machine of gabriel
25/27
Material Reo(al Rate#-It?s the (olue of aterial reo(ed by the drill perunit tie
MRR @ >D1B C$ A f A 2 DB in
Machining Tie >T$ #-
It depends upon the length >l$ of the hole to be
drilled ! to the 'peed >2$ and feed >f$ of the drill
t @ L B f 2 in
-
8/10/2019 Drilling machine of gabriel
26/27
&recautions for Drilling achine Lubrication is iportant to reo(e heat
and friction.
Machines should be cleaned after use
"hips should be reo(ed using brush.
T-slots! groo(es! spindles slee(es! belts!pulley should be cleaned.
Machines should be lightly oiled to pre(entfro rusting
-
8/10/2019 Drilling machine of gabriel
27/27
'afety &recautions
Do not support the work piece by hand 3 usework holding de(ice.
/se brush to clean the chip
2o adEustents while the achine is operating Fnsure for the cutting tools running straight
before starting the operation.
2e(er place tools on the drilling table 6(oid loose clothing and protect the eyes.
Fase the feed if drill breaks inside the work piece.