DRILLING ATTACHMENT CPA X-TEND - … · DRILLING ATTACHMENT CPA X-TEND ... Dust collector option...
Transcript of DRILLING ATTACHMENT CPA X-TEND - … · DRILLING ATTACHMENT CPA X-TEND ... Dust collector option...
DRILLING ATTACHMENT CPA X-TEND14/12 24/20
Feed beam Steel SteelDrifter HC 109 HC 150 HC 170 HC 109 HC 150 HC 170
Inlet power @ controls 35 kW 42 kW 50 kW 35 kW 42 kW 50 kW
Blows/min 2560-2900 2170-2530 2450 2560-2900 2170-2530 2450Reverse percussion Option Option yes Option Option yes
Main characteristicsWeigth (without option) 2640 kg 2660 kg 2820 kg 2800 kg 2820 kg 2980 kgLength 7221 mm 23’ 8” 9966 mm 32’ 8”Width 1350 mm 4’ 5” 1350 mm 4’ 5”Height 1810 mm 6” 1810 mm 6’Feed oscillation O +/- 27° +/- 27°
Drilling characteristicsBit diameter mm (‘) 64 à 102
2.5” à 4“76 à 115 3” à 4.5”
89 à 155 3.5” à 6”
64 à 102 2.5” à 4”
76 à 115 3” à 4.5”
89 à 155 3.5” à 6”
Rod diameter mm (‘) 38 - 45 mm 1” 1/2 -1” 3/4
45 - 51 mm 1” 3/4 - 2”
45 - 51 mm 2”
38 - 45 mm 1” 1/2 -1” 3/4
45 - 51 mm 1” 3/4 - 2”
45 - 51 mm 2”
Length of starter rod 4270 mm 14’ 7230 mm 24’Drilled lenght (single pass) 3560 mm 11’ 8” 6605 mm 21’ 8”
Rods handlingRod adder Option OptionCarrousel Option 7+1 Option 4+1Length of extension rods 3660 mm 12’ 6100 mm 20’Drilled lenght rod adder 7220 mm 23’ 8” 12700 mm 41’ 8” rod changer 29180 mm 95’ 8” 31630 mm 101’ 8”
ControlsType of controls Wired control panel in cabin
Radio remote as optionCarrier characteristics
Weight metric tons 22 à 35 22 à 40 22 à 35 25 à 40Minimum power kW (hp) 80 (109) 88 (119) 105 (141) 80 (109) 88 (119) 105 (141)Required oil flow l/min (gpm) 180 (48) 195 (51) 210 (55) 180 (48) 195 (51) 210 (55)Required oil pressure bar (psi) 190 (2700) 195 (2800) 210 (3000) 190 (2700) 195 (2800) 210 (3000)
OptionsDust collector optionQuick hitch (mécanical) requires mechanical fixation kitQuick hitch (hydraulic) requires mechanical fixation kitConnection hoses kitMechanical fixation kitDrilling angle indicator
AccessoriesAir compressor m3/min (cfm) 8 (282) 10 (350) 11 (390) 8 (282) 10 (350) 11 (390)
Steel feed GCX 14’’ long feed 24’’ (option)
Hoses reel
Rods carrousel (option) 7 x 12’’ rods for X-Tend 14/12 4 x 20’’ rods for X-Tend 24/20
Rod adder
Drifter HC 150 RP HC 109 RP (option) HC 170 RP (option)
Montabert drilling automatics «Intelsense»
Quick hitch (option)
Feed oscillation +/- 27°
Emergency stop * on feed * on controls
Hydraulic dust collector (option)
Pre separator (dust collector option)
Automatic thread greasing
Hydraulic opening centralizer
Pre equipment for dust collector
Accessories and Options
Diesel driven compressor type 10/105
Hydraulic air module type VHP 300 CM
Weight 1965 kg Compressor weigth 519 kgAir flow 10,6 m3/min Oil separator weigth 118 kgMax air pressure 13,8 bar Air flow 8,3 m3/minEngine 4IRD5AE Max air pressure 13,8 barNumber of cylinders 4 Required oil flow 200 l/minRated power 93 kW Required oil pressure 190 barCooling water Inlet power 83 kWVoltage 24 V Cooling hydraulic coolerFuel tank capacity 219 l Voltage 12 V
Hydraulic dust collector
Max drilling bit 151 mmFiltration area 28,8 m2
Required oil flow 30 l/minRequired oil pressure 150 barDimension width 1035 mm
length 760 mmheigth 1860 mm
Weigth 290 kg
Quick hitch
From model QH100, mechanical or hydraulic lock device, for pins dia. 100 mm (weight 725 kg)to model QH 140, mechanical or hydraulic lock device, for pins dia. 140 mm (weight 1675 kg)
Side drilling (option)
Montabert : present in the world market in morethan 100 countries.Optimize the performance of your drillingattachments by contacting our experienced networkto deal with your queries.Montabert will provide you with its expertknowledge at the time of start-up, as well as adviceon maintenance with original spare parts, technicalsupport and training.
MONTABERT SAS - 203, route de Grenoble - 69800 Saint Priest, France - tel : +33-(0)4 72 22 97 97 - fax: +33-(0)4 72 22 97 56
montabert [email protected] / www.montabert.comNothing contained in this brochure is intended to extend any warranty or representation expressed or implied, regarding the products described herein. Any such warranties or other terms and conditions of sale products shall be in accordance with Montabert standards terms and conditions of sales for such products, which areavailable upon request. Specifi cations and machines can be modifi ed at any time and without notice.
Your distributor :
© 2009 by Montabert SAS
X-Tend 12/14 7218 mm
X-Tend 20/24 9963 mm
X-Tend 12/14 7218 mm
X-Tend 20/24 9963 mm
2131
2528
For excavators from
22 to 40 tons