Download (PDF, 2.69MB) - CBI Offroad - Tire - …€¦ · Actual products ma differ slightl from...

///////////////////////P R O D U C T C A T A L O G

2 0 1 7 C A T A L O G

Actual products may differ slightly from product images Actual products may differ slightly from product images

1st Gen Tacoma (1995.5-2004) T1 ................. 4-8

2nd Gen Tacoma (2005-2015) T2 ................. 9-14

3rd Gen Tacoma (2016-present) T3 ........... 15-20

3rd Gen 4Runner (1996-2002) T4R3 .......... 21-25

4th Gen 4Runner (2003-2009) T4R4 .......... 26-29

5th Gen 4Runner (2010-present) T4R5 ...... 30-33

CBI Swing Arm ......................................... 34-35

Jeep Wrangler (2007-present) JK-JKU ..... 36-38

DIY / Misc. .......................................................39

Apparel ............................................................40

Contents

CBI WarrantyCBI Offroad Fab warrants CBI Offroad products to the original retail purchaser to be free of defects in material and workmanship for as long as the original purchaser owns the vehicle on which products were originally installed. It is the sole discretion of CBI Offroad to determine warranty eligibility.

· This warranty does not cover or include product finish, improperly installed or applied products, improperly maintained products, or products used for racing or competition or damage due to abuse or neglect.

· All returns must be accompanied by an original invoice. It is the customer’s responsibility to remove the product from the vehicle. Inbound shipping charges (from you to us) are the responsibility of the customer. CBI Offroad will pay the return freight.

Copyright 2017. All rights reserved, CBI Offroad Fab. Reproduction of this catalog and/or any of its contents without written permission is strictly prohibited.

CBI Offroad Fab reserves the right to update, discontinue, redesign, modify finish, change part numbers or component build parts, and pricing if deemed necessary without written notice. CBI Offroad Fab, and any associ-ated dealers are not responsible for misprints or typographical errors that may have inadvertently been made within this catalog, or pricing sheets. WARNING: Neither the seller nor the manufacturer will be liable for any loss, damage, or injury directly or indirectly arising from the use of or inability to determine the use of these products. Before using , the user shall determine the suitability of the product(s) for its intended use(s), and the user shall assume all responsibility and risk in connection therewith.

About //////////////////////////At CBI Offroad our line of off-road body armor and protection match our moto: “Trail Proven – Adven-ture Ready!” Whatever type of adventure you pur-sue our off-road body armor will get you there with the style, functionality, and protection you need. CBI Offroad is a company that was founded on principles of quality craftsmanship and impeccable design for off-road vehicles. Our first bumper was built back in 1999 and was hand crafted to per-fection. We continue this tradition today as each product is manufactured by skilled fabricators and welders. All CBI Offroad products are assembled and built in our Idaho Falls, ID facility by skilled American workers. It is our goal that each product we produce will exceed our customers’ expecta-tions in both quality and function.

/////////////////////////////// C B I O F F R O A D P R O D U C T C A T A L O G 2 0 1 7 page 3

Actual products may differ slightly from product images Actual products may differ slightly from product images//////////////////////////

DIY 1st Gen Tacoma Front Bumper //////////////////////////

Save money by building your own CBI bumper for your 1st generation Toyota Tacoma. We pro-vide all of the mounting hardware and parts needed to build your new bumper. All of the parts are cut and bent to fit together without difficulty. * Center grill guard (T1-CGG) and Headlight protection (T1-HP) sold separately.

T1-DIY-FB .......................................................................................................... $424.99T1-CGG (Center Grill Guard) ..................................................................................... $34.99T1-HP (Headlight Protection) ..................................................................................... $44.99

1st Gen Tacoma Frame Plates ///////

CBI Offroad Toyota Tacoma frame reinforcement plates are designed to strengthen the frame of your Toyota Tacoma truck. Frame plates should be used when you are adding additional weight to your Taco-ma by way of a rear bumper and tire carrier. Install time: 1.5 hr

T1-FRM-PT ........................................................... $69.99

Our 1st Generation Toyota Tacoma Ditch Light Brackets give you the ability to run aftermarket lights on the hood of your truck. Product comes powder coated in a black finish. Install time: 1 hr

T1/T4R3-DLB ................$59.99Antenna BracketsT1/T4R3-AM-DS ............$39.99T1/T4R3-AM-PS ............$39.99

1st Gen Tacoma Ditch Light Brackets ////

Tacoma1ST GEN

Taco

ma

1995

.5-2

004

1ST G

ENTaco

ma

1995.5-2004

1ST GEN

Bare Metal

C B I O F F R O A D P R O D U C T C A T A L O G 2 0 1 7 page 5


CBI Toyota Tacoma rock sliders are strong enough to lift your vehicle with a jack and provide the strength that will take the abuse of gnarly off-road trails rather than the rocker panels of your truck! Sliders can also be ordered with the option “Kickout” design for added off-road protection and aggressive styling. The hardcore off-roader should consider the DOM (Drawn Over Mandrel) tubing upgrade that provides substantially more impact resistance.Install time: 1.5 hr –Optional Powder coat +$150

T1-RSBO-KKOT ...................$639.99T1-RSBO-KKOT-DOM ..........$739.99

1st Gen Tacoma Rock Sliders //////////////////////////

T1-RSBO ..............................$599.99T1-RSBO-DOM ....................$699.99

<< BOLT ON >>

<< WELD ON >>

T1-RSWO-KKOT ..................$599.99T1-RSWO-KKOT-DOM .........$699.99

T1-RSWO .............................$559.99T1-RSWO-DOM ...................$659.99

The Moab 1.0 1st Gen Toyota Tacoma front bumper is specifically designed to give you added protection and usability without sacrificing additional weight. Winch mount and LED turn signals included.Install time: 3 hrs –Optional Powder coat +$175

Moab 1.0 //////////////////////////

T1-FB-MB1 ...........................$899.99

T1-FB-MB1-CGP ..................$999.99

T1-FB-MB1-FGP ................$1099.99

T1-RB-TR1 ...........................$599.99

T1-RB-TR1-PKG ................$1249.99

The Trail Rider 1.0 is our simple, light weight bumper replacement option for your 1st gen Tacoma. Get protection and increased departure angle without sacrificing additional weight! This bumper is a direct bolt on factory replace-ment. Receiver hitch included (not load rated) Install time: 2 hrs –Optional Powder coat +$150

TRAIL RIDER 1.0 //////////////////////////Taco

ma

1995

.5-2

004

1ST G

ENTaco

ma

1995.5-2004

1ST GEN

90 lbs

102 lbs

115 lbs

75 lbs

150 lbs

Install time: 5 hrs –Optional Powder coat +$225

Bare Metal Bare Metal


Bare Metal

Bare Metal


Bare Metal

100 lbs

98 lbs

96 lbs

90 lbs

See pg 34 for NEW swing arm design

C B I O F F R O A D P R O D U C T C A T A L O G 2 0 1 7page 6 C B I O F F R O A D P R O D U C T C A T A L O G 2 0 1 7 page 7

Actual products may differ slightly from product images

T1-RB-OB1 ...........................$799.99

T1-RB-OB1-PKG ................$1449.99

The Outback 1.0 rear bumper is specifically designed to be our premium offering for the 1st gen Toyota Tacoma rear bumper. With the Outback 1.0 you get a greatly improved departure angle, the strength of an unbreakable bumper and added side panel protection. No cutting required. Receiver hitch included (not load rated) Install time: 2 hrs –Optional Powder coat +$175

Outback 1.0 //////////////////////////

T1-RB-BM1 ...........................$999.99

T1-RB-BM1-PKG ................$1649.99

The Bushmaster 1.0 rear bumper is specifically designed to be our premium high clearance offering for the 1st gen Toyota Tacoma rear bumper. This bumper requires cutting of the body panels for installation. Receiver hitch included (not load rated) Install time: 4 hrs –Optional Powder coat +$175

Bushmaster 1.0 //////////////////////////

//////////////////////////Tacoma2ND GEN

Taco

ma

1995

.5-2

004

1ST G

ENTaco

ma

2005-2015

2ND GEN

Install time: 7 hrs –Optional Powder coat +$225 Install time: 5 hrs –Optional Powder coat +$225

113 lbs

178 lbs

98 lbs

165 lbs

Bare Metal


Bare Metal



C B I O F F R O A D P R O D U C T C A T A L O G 2 0 1 7page 8


CBI Toyota Tacoma rock sliders are strong enough to lift your vehicle with a jack and provide the strength that will take the abuse of gnarly off-road trails rather than the rocker panels of your truck! Sliders can also be ordered with the option “Kickout” design for added off-road protection and aggressive styling. The hardcore off-roader should consider the DOM (Drawn Over Mandrel) tubing upgrade that provides substantially more impact resistance. Completely bolt on application!Install time: 1.5 hrs –Optional Powder coat +$150

T2/T3-RSBO-KKOT ..............$639.99T2/T3-RSBO-KKOT-DOM ....$739.99

2nd Gen Tacoma Rock Sliders //////////////////////////

T2/T3-RSBO .........................$599.99T2/T3-RSBO-DOM ...............$699.99

<< BOLT ON >>

<< WELD ON >>

T2/T3-RSWO-KKOT .............$599.99T2/T3-RSWO-KKOT-DOM ...$699.99

T2/T3-RSWO ........................$559.99T2/T3-RSWO-DOM ..............$659.99

2nd Gen Tacoma Skid Plates //////////////////////////

The 2nd Gen Toyota Tacoma skids (3/16” plate) are a great option to offer extra protection for the drive-train on your truck. You can choose from just the front skid to a full skid that protects all the way back to the t-case. Install time: 1.5 hrs –Optional Powder coat for full skid +$200

T2/T3-SKID-FRT ......................... $239.99T2/T3-SKID-MID .......................... $199.99T2/T3-SKID-TRAN ....................... $289.99

Our 2nd Generation Toyota Tacoma Ditch Light Brackets give you the ability to run aftermarket lights on the hood of your Tacoma. Product comes powder coated in a black finish. Install time: 1 hrs

T2-DLB ..........................$59.99Antenna BracketsT2-AM-DS ......................$39.99T2-AM-PS ......................$39.99

2nd Gen Tacoma Ditch Light Brackets ////

Taco

ma

2005-2015

2ND GENTaco

ma

2005

-201

5

2ND G

EN

Double cab long bed option available add this part number to your order.

DCLB ...............................add $50.00


DCLB ...............................add $50.00

Bare Metal

26 lbs

30 lbs

78 lbs

Bare Metal

Bare Metal

Bare Metal

Bare Metal

2nd Gen Tacoma Whip Mount ////Add an antenna whip or flag using our T2 Whip Mount. Bracket mounts to factory bed rail and tailgate latch assembly on drivers side. Comes powder coated in a black finish. Install time: .5 hrs

T2-WIP-DS ....................$32.99T2-WIP-PS ....................$32.99

110 lbs

100 lbs

105 lbs

95 lbs



Moab 2.0 //////////////////////////

T2-MB2-05-11 .................$899.99T2-MB2-12-15 ................$899.99-PRO (aluminum) ........add $250.00

T2-MB2-CGP-05-11 ........$924.99T2-MB2-CGP-12-15 .......$924.99-PRO (aluminum) ........add $250.00

T2-MB2-FGP-05-11 ......$1049.99T2-MB2-FGP-12-15 ......$1049.99-PRO (aluminum) ........add $250.00

Dakar Rally //////////////////////////

T2-DR-CGP-SHRT .. $924.99

T2-DR-CGP ............. $924.99

T2-DR-FGP ........... $1049.99

The 2nd Gen Toyota Tacoma Moab 2.0 front bumper is specifically designed to give you added protection and usability without sacrificing additional weight. The Moab 2.0 is a great option for a winch bumper that greatly in-creases approach angle. Another great feature is the fog lamp cutouts which allow you to maintain the use of your stock fog lamps or LED lights. Install time: 3 hrs –Optional Powder coat +$175

Inspired by the world renown adventure race, The Paris-Dakar Rally, we have developed the ultimate off-road bumper that is worthy to carry the name of such a race! Every aspect of this Dakar Rally Toyota Tacoma front bumper has been analyzed for strength, functionality, style and design, and weight reduction! Every road is an adventure and this bumper will get you there!Install time: 3 hrs –Optional Powder coat +$175

T2-RB-BM2 .........................$1024.99

T2-BM2-PKG ......................$1674.99

The 2nd Gen Tacoma Bushmaster 2.0 rear bumper is specifically designed to be our premium high clearance offering for the 2nd gen Toyota Tacoma rear bumper. Cutting the rocker panel is required for installation. Receiver hitch included (not load rated)Install time: 4 hrs –Optional Powder coat +$175

Busmaster 2.0 //////////////////////////

T2-RB-TR2 ...........................$899.99

T2-TR2-PKG .......................$1549.99

The Trail Rider 2.0 2nd Gen Tacoma rear bumper is specifically designed to give you added rear protection and usability without sacrificing additional weight. Receiver hitch included (not load rated)Install time: 2.5 hrs –Optional Powder coat +$175

TRAIL RIDER 2.0 //////////////////////////Taco

ma

2005-2015

2ND GENTaco

ma

2005

-201

5

2ND G

EN

100 lbs (steel)42 lbs (aluminum)



Bare Metal

85 lbs

95 lbs

110 lbs Install time: 7 hrs –Optional Powder coat +$225 Install time: 5.5 hrs –Optional Powder coat +$225

125 lbs

190 lbs

100 lbs

165 lbs

Bare Metal

Bare Metal

Bare Metal

Bare Metal

Bare Metal

Bare Metal

Bare Metal

Bare Metal

Bare Metal





Overland Tacoma Bed Rack //////////////////////////

High Clearance Front Receiver Hitch ////

The 2nd Gen Toyota Tacoma High Clearance Front Receiver Hitch is specifically designed to give you maximum clearance while adding increased functionality. While giving the ability to run a winch carrier or any receiver mount. Some cutting required. Comes powder coated black.Install time: 4 hrs

T2-FRH ............................................................... $374.99

Our Overland bars provide an excellent mounting point for roof top tents, bike racks, gear, or just about anything. Mounts to the bed rails of the 2nd gen Tacoma. Kit includes a set of two com-plete bed bars and rails. Comes powder coated black.Install time: .75 hrs

Overland Bars ////

//////////////////////////Tacoma3RD GEN

Taco

ma

2016-present

3RD GENTaco

ma

2005

-201

5

2ND G

EN

50 lbs

36 lbs (steel)


Our Overland bed rack breaks the mold for the 2nd gen Tacoma. With its low profile, multiple mounting and tie down points, there is literally nothing this bed rack can’t handle. Take all your gear with you on your next overland trip and have room to spare. Available in steel or aluminum.Install time: 1 hr –Optional Powder coat +$175

T2/T3-OBR-SB (steel) ......................................................................................... $799.99T2/T3-OBR-SB-PRO (aluminum) ......................................................................... $999.99T2/T3-OBR-LB (steel) ......................................................................................... $849.99T2/T3-OBR-LB-PRO (aluminum) ....................................................................... $1049.99

T2/T3-OBR-MT (Max Tax Mount) ............................................................................ $89.99T2/T3-OBR-BK (Bike Mount Driver or Pass) ............................................................. $124.99

Bare Metal

T2/T3-OB ............................................................$399.99T2/T3-OB-HM (Hi-Lift Mount) ....................................$74.99T2/T3-OB-BK (Bike Mount Driver or Pass) .................$124.99



CBI Toyota Tacoma rock sliders are strong enough to lift your vehicle with a jack and provide the strength that will take the abuse of gnarly off-road trails rather than the rocker panels of your truck! Sliders can also be ordered with the option “Kickout” design for added off-road protection and aggressive styling. The hardcore off-roader should consider the DOM (Drawn Over Mandrel) tubing upgrade that provides substantially more impact resistance. Completely bolt on application! Install time: 1.5 hr –Optional Powder coat +$150

T2/T3-RSBO-KKOT ..............$639.99T2/T3-RSBO-KKOT-DOM ....$739.99

3rd Gen Tacoma Rock Sliders //////////////////////////

T2/T3-RSBO .........................$599.99T2/T3-RSBO-DOM ...............$699.99

<< BOLT ON >>

<< WELD ON >>

T2/T3-RSWO-KKOT .............$599.99T2/T3-RSWO-KKOT-DOM ...$699.99

T2/T3-RSWO ........................$559.99T2/T3-RSWO-DOM ..............$659.99

3rd Gen Tacoma Skid Plates //////////////////////////

The 3rd Gen Toyota Tacoma skids (3/16” plate) are a great option to offer extra protection for the drive-train on your truck. You can choose from just the front skid to a full skid that protects all the way back to the t-case.Install time: 1.5 hr –Optional Powder coat for full skid +$175

T2/T3-SKID-FRT ............................................................................................... $239.99T2/T3-SKID-MID ................................................................................................ $199.99T2/T3-SKID-TRAN ............................................................................................. $289.99T3-SKID-LCA ..................................................................................................... $169.99T3-SKID-GAS .................................................................................................... $275.99T3-SKID-GAS-PRO (1/4”aluminum) ....................................................................... $474.99

Our 3rd Generation Toyota Tacoma Ditch Light Brackets give you the ability to run aftermarket lights on the hood of your Tacoma. Product comes powder coated in a black finish. Install time: .5 hr

T3-DLB ..........................$59.99Antenna BracketsT3-AM-DS ......................$39.99T3-AM-PS ......................$39.99

3rd Gen Tacoma Ditch Light Brackets ////

Taco

ma

2016-present

2ND GENTaco

ma

2016

-pre

sent

3RD G

EN

26 lbs

30 lbs

78 lbs


DCLB ...............................add $50.00


DCLB ...............................add $50.00

Bare Metal

Bare Metal


Bare Metal

110 lbs

100 lbs

105lbs

95 lbs

LCA Skids



Our best offering to date for the Tacoma series of trucks! With greatly increased approach angles, a ton of added strength, and the ability to mount a winch you get it all. Also included is an internal mount for a 20” single row light bar. Factory fog light bracket mounts are also included. Product offered in steel or aluminum. Install time: 4 hr –Optional Powder coat +$175

T3 Front Bumper //////////////////////////

T3-FB-CGP .........................$1049.99-PRO (aluminum) ..............add $350.00

T3-FB-FGP .........................$1099.99-PRO (aluminum) ..............add $350.00

T3-RB ...................................$899.99T3-RB-HC ...........................$1099.99

T3-RB-PKG ........................$1549.99T3-RB-HC-PKG ..................$1749.99

Offering a complete factory replacement bumper that greatly improves depar-ture angle and strength starts with a CBI Offroad rear bumper. Our Overland T3 rear bumper does just that! Bumper comes standard with a receiver hitch (not load rated), factory trailer wiring mount, and LED license plate light and mount. Optional High Clearance bumper available. *High Clearance bumper requires cutting the bed Install time: 2.5 hr –Optional Powder coat +$175

T3 Rear Bumper //////////////////////////Bumper guard/Light mount ////

Add a whole lot of style and the ability to mount up to a 30” light bar on the front of your new Tacoma! This easy to install bumper guard is the perfect addition to any Tacoma. Minor trimming required for installation. Comes powder coated black. Install time: 3 hrsT3-BG ................................................................. $399.99

Mount a winch to your 2016+ Tacoma while still maintaining the facto-ry bumper and look. Cutting required to mount the fairlead. Fitment for non-integrated solenoid winches. Comes powder coated black. Install time: 4 hrs T3-HWM ..................................................................... $374.99

Hidden Winch Mount ////

Push Bar ////

Add protection and unique, one of a kind styling with the new CBI Offroad Tacoma Push Bar. This mount bolts to the factory bumper and allows up to a 30” light bar to be mounted on top. Couple this with our hidden winch mount for full integration of the winch for a custom look like no other! Product comes powder coated black.Install time: 4 hrs

T3-PB ................................................................. $399.99

Light Bar Mount ////

Mount up to a 30” light bar behind the factory lower grill opening. It also have the ability to mount dually sized LED lights or two 10” light bars or any combination with this uniquely design mount. Comes powder coated black. Install time: 2 hrs

T3-LM ................................................................... $89.99

Taco

ma

2016-present

2ND GENTaco

ma

2016

-pre

sent

3RD G

EN

T3-FB ....................................$999.99-PRO (aluminum) ..............add $350.00

105 lbs

118 lbs

130 lbs

100 lbs

171 lbs

Install time: 5.5 hr –Optional Powder coat +$225

40 lbs 55 lbs

50 lbs20 lbs

Bare Metal

Bare Metal

Bare Metal

Bare Metal

Bare Metal


*T3 Bumpers available in Non Flare and Flare Width to accommodate wider after market flares



Overland Tacoma Bed Rack //////////////////////////Our Overland bed rack breaks the mold for the 3rd gen Tacoma. With its low profile, multiple mounting and tie down points, there is literally nothing this bed rack can’t handle. Take all your gear with you on your next overland trip and have room to spare. Available in steel or aluminum.Install time: 1 hr –Optional Powder coat +$175

T2/T3-OBR-SB (steel) ......................................................................................... $799.99T2/T3-OBR-SB-PRO (aluminum) ......................................................................... $999.99T2/T3-OBR-LB (steel) ......................................................................................... $849.99T2/T3-OBR-LB-PRO (aluminum) ....................................................................... $1049.99

T2/T3-OBR-MT (Max Tax Mount) ............................................................................ $89.99T2/T3-OBR-BK (Bike Mount Driver or Pass) ............................................................. $124.99

High Clearance Front Receiver Hitch ////

The 3rd Gen Toyota Tacoma High Clearance Front Receiver Hitch is specifically designed to give you maximum clearance while adding increased functionality. Some cutting required. Comes powder coated black. Install time: 4 hrs

T3-FRH ............................................................... $374.99

Our Overland bars provide an excellent mounting point for roof top tents, bike racks, gear, or just about anything. Mounts to the bed rails of the 3rd gen Tacoma. Kit includes a set of two com-plete bed bars and rails. Comes powder coated black. Install time: .75 hrs

Overland Bars ////

//////////////////////////4Runner3RD GEN

4Runner

1996-2002

3RD GENTaco

ma

2016

-pre

sent

3RD G

EN

50 lbs

36 lbs (steel


Bare Metal

T2/T3-OB ............................................................$399.99T2/T3-OB-HM (Hi-Lift Mount) ....................................$74.99T2/T3-OB-BK (Bike Mount Driver or Pass) .................$124.99



3rd Gen 4Runner Skid Plates //////////////////////////

Protect the undercarriage on your Toyota 4runner with a full set of CBI 3rd gen skid plates. Built from 3/16” formed plate steel, these skids will be a great addition to any type of off road adven-ture. Install time: 1.5 hrs –Optional Powder coat for full skid +$300

T4R3-SKID-FRT ................................................................................................ $259.99T4R3-SKID-REAR ............................................................................................. $249.99T4R3-SKID-FULL .............................................................................................. $509.98

Our 3rd Generation 4runner Ditch Light Brackets give you the ability to run aftermarket lights on the hood of your 4Runner. Product comes powder coated in a black finish.Install time: 1.5 hrs

T1/T4R3-DLB ................$59.99Antenna BracketsT1/T4R3-ANT-D .............$39.99T1/T4R3-ANT-P .............$39.99

3rd Gen 4Runner Ditch Light Brackets ////

Front Skid

Rear Skid

With CBI 3rd gen Toyota 4Runner rock sliders take advantage of easy installation, and get the strength you need to lift your vehicle with a jack. Also your sliders will take the abuse of gnarly off-road trails rather than the rocker panels of your truck! Install time: 1.5 hrs –Optional Powder coat +$150

3rd Gen 4runner Rock Sliders //////////////////////////

<< WELD ON >>

T4R3-RSWO-KKOT .............$574.99T4R3-RSWO-KKOT-DOM ....$674.99

T4R3-RSWO ........................$499.99T4R3-RSWO-DOM ...............$599.99

T4R3 Battery Tray (Group 31 size) //////////////////////////

Convert your battery tray to accept the larger group 31 size batteries. Product comes powder coated black. Install time: .5 hrs

T4R3-BT .............................................................................................................. $79.99

4Runner

1996-2002

3RD GEN4Runner

1996

-200

2

3RD G

EN

60 lbs

60 lbs

Bare Metal


64 lbs 60 lbs



The 3rd Gen. 4Runner front hybrid bumper features our best design for maximum approach angle, great weight savings through design, uncompromised strength and durability to withstand your harshest abuse. And for the times when you get in over your head or need to help a buddy out you can rely on built in recovery points and winch mount that pull directly off of the frame to get the job done. Install time: 3 hrs –Optional Powder coat +$175

T4R3 Front Hybrid Bumper //////////////////////////

T4R3-FB-HYB-CGP-SHRT.........................$899.99

T4R3-HYB ..............................................$899.99T4R3-HYB-FW (Flare Width) ......................$899.99

T4R3-RB-HYB-PKG ...............................$1549.99T4R3-RB-HYB-FW-PKG (Flare Width) .......$1549.99

The 3rd Gen. 4Runner features our best design for maximum departure angle, great weight savings through design, uncompromised strength and durability to with-stand your harshest abuse. And for the times when you get in over your head or need to help a buddy out you can rely on built in recovery points that pull directly off of the frame to get the job done. (Available in standard or flare width)

T4R3 Rear Hybrid Bumper //////////////////////////

*The factory spare will not fit in the stock location when installing this bumper.

T4R3-RB-PLT ....................................... $949.99T4R3-RB-PLT-FW (Flare Width) ............... $949.99

T4R3-RB-PLT-PKG ............................................. $1599.994R3-RB-PLT-FW-PKG (Flare Width) ....................... $1599.99

The 3rd Generation 4runner T4R3 Rear bumper is specifically designed to handle whatever mess you can get yourself into. Design components incorporate for maximum approach angles, uncompromised strength and durability to withstand your harshest abuse, and 3/4” recovery points to get you out of those tight situations. (Available in standard or flare width)

T4R3 Rear Plate Bumper //////////////////////////

4Runner

1996-2002

3RD GEN4Runner

1996

-200

2

3RD G

EN

95 lbs

100 lbs

165 lbs 125 lbs

190 lbs

Install time: 5.5 hrs –Optional Powder coat +$225 Install time: 3.5 hrs –Optional Powder coat +$175 Install time: 5.5 hrs –Optional Powder coat +$225 Install time: 3.5 hrs –Optional Powder coat +$175

The 3rd Gen. 4Runner front hybrid bumper features our best design for maximum approach angle, great weight savings through design, uncompromised strength and durability to withstand your harshest abuse. And for the times when you get in over your head or need to help a buddy out you can rely on built in recovery points and winch mount that pull directly off of the frame to get the job done. Install time: 3 hrs –Optional Powder coat +$175

T4R3 Front Hybrid Full Grill Protection //////////////////////////

T4R3-FB-HYB-FGP ...........................................$949.99

110 lbsBare Metal


Bare Metal




T4R3-FB-HYB ............................................$899.99

90 lbsBare Metal

T4R3-FB-HYB-CGP ..........................................$899.99

100 lbs

Bare Metal


Actual products may differ slightly from product images Actual products may differ slightly from product images//////////////////////////4Runner4TH GEN

4th Gen 4Runner Skid Plates //////////////////////////

Protect the undercarriage on your Toyota 4runner with a full set of CBI 4th gen skid plates. Built from 3/16” formed plate steel, these skids will be a great addition to any type of off road adven-ture. Install time: 1.5 hr –Optional Powder coat for full skid +$200

T4R4-SKID-FRT ................................................................................................ $239.99T4R4-SKID-MID ................................................................................................ $199.99T4R4-SKID-TRAN ............................................................................................. $289.99T4R4-GAS-SKID ............................................................................................... $289.99

Our 4th Generation 4runner Ditch Light Brackets give you the ability to run aftermarket lights on the hood of your 4Runner. Product comes powder coated in a black finish.Install time: 1.5 hrs

T4R4-DLB ......................$59.99Antenna BracketsT4R4-ANT-D ..................$39.99T4R4-ANT-P ..................$39.99

4TH Gen 4Runner Ditch Light Brackets ////

4Runner

2003-2009

4TH GEN4Runner

2003

-200

9

4TH G

EN

Bare Metal

26 lbs

30 lbs

78 lbs



CBI Toyota Tacoma rock sliders are strong enough to lift your vehicle with a jack and provide the strength that will take the abuse of gnarly off-road trails rather than the rocker panels of your truck! Sliders can also be ordered with the option “Kickout” design for added off-road protection and aggressive styling. The hardcore off-roader should consider the DOM (Drawn Over Mandrel) tubing upgrade that provides substantially more impact resistance. Install time: 1.5 hr –Optional Powder coat +$150

4TH Gen 4runner Rock Sliders //////////////////////////

<< WELD ON >>

T4R4-RSWO-KKOT .............$574.99T4R4-RSWO-KKOT-DOM ....$674.99

T4R4-RSWO ........................$499.99T4R4-RSWO-DOM ...............$599.99

4th gen 4Runner High Clearance Front Receiver Hitch //////////////////////////

The 4th Gen Toyota 4Runner High Clearance Front Receiver Hitch is specifically designed to give you maximum clearance while adding increased functionality. Comes powder coated black.Install time: 4 hrs

T4R4-FRH ......................................................................................................... $374.99

Only CBI Offroad Fab can outfit your vehicle with the proper body armor for someone that is truly “Recreationally Insane!” Whether you’re into rock crawling, trail expeditions, or just good ol’ weekend fun our 4th Generation Toyota 4Runner front winch bumper provides the ultimate protection without sacrifice.Install time: 3 hrs –Optional Powder coat +$175

T4R4 Front Bumper //////////////////////////

T4R4-FB-03-05 .....................$899.99T4R4-FB-06-09 .....................$899.99-PRO (aluminum) ..............add $300.00

T4R4-FB-CGP-03-05 ............$949.99T4R4-FB-CGP-06-09 ............$949.99-PRO (aluminum) ..............add $300.00

T4R4-FB-FGP-03-05 ..........$1049.99T4R4-FB-FGP-06-09 ..........$1049.99-PRO (aluminum) ..............add $300.00

T4R4-RB-03-05 ..................$1399.99T4R4-RB-06-09 ..................$1399.99

T4R4-RB-PKG-03-05 .........$2049.99T4R4-RB-PKG-06-09 .........$2049.99

The 4th Gen. 4Runner rear bumper package is the best that CBI Offroad Fab offers to take your 4Runner to the next level. This package offers specifically designed components with the true “recreationally insane” enthusiast in mind. It gives your 4Runner the best in looks and vehicle protection money can buy! includes bolt on receiver (not load rated) Install time: 4 hr –Optional Powder coat +$200

T4R4 Rear Bumper //////////////////////////4Runner

2003-2009

4TH GEN4Runner

2003

-200

9

4TH G

EN

105 lbs

115 lbs

130 lbs

Install time: 7 hr –Optional Powder coat +$300

130 lbs

195 lbs


Bare Metal

Bare Metal

Bare Metal

Bare Metal

Bare Metal

60 lbs65 lbs



Actual products may differ slightly from product images Actual products may differ slightly from product images//////////////////////////4Runner5TH GEN

5th Gen 4Runner Skid Plates //////////////////////////

Protect the undercarriage on your Toyota 4runner with a full set of CBI 4th gen skid plates. Built from 3/16” formed plate steel, these skids will be a great addition to any type of off road adventure. Completely bolt on. Install time: 1.5 hr –Optional Powder coat for full skid +$200

T4R5-SKID-FRT ....................$324.99T4R5-SKID-REAR .................$399.99T4R5-SKID-FULL ..................$509.98T4R5-SKD-LCA .....................$160.99T4R5-SKD-LCA-KDSS ..........$190.99T4R5-SKID-GAS ...................$275.99

Our 4th Generation 4runner Ditch Light Brackets give you the ability to run aftermarket lights on the hood of your 4Runner. Product comes powder coated in a black finish.Install time: 1 hr

T4R5-DLB ......................$59.99Antenna BracketsT4R5-ANT-D ..................$39.99T4R5-ANT-P ..................$39.99

5TH Gen 4Runner Ditch Light Brackets ////

Front Skid

Rear Skid

4Runner

2010-present

5TH GEN4Runner

2010

-pre

sent

5TH G

EN

55 lbs

83 lbs

Bare Metal

LCA SkidKDSS

Gas Tank Skid

T4R5-SKID-FRT-PRO ................$424.99T4R5-SKID-REAR-PRO .............$525.99T4R5-SKID-GAS-PRO ...............$474.99

Bare Metal(aluminum)



The 5th Gen Toyota 4Runner High Clearance Front Receiver Hitch is specifically designed to give you maximum clearance while adding increased functionality. Comes Powder coated black Install time: 4 hrs

T4R5-FRH .......................................................................................$374.99

T4R4-RB ...............................$549.99

T4R5 Rear Bumper //////////////////////////With CBI 5th gen Toyota 4Runner rock sliders take advantage of easy installation, and get the strength you need to lift your vehicle with a jack. Also your sliders will take the abuse of gnarly off-road trails rather than the rocker panels of your truck! Install time: 1.5 hrs –Optional Powder coat +$150

5TH Gen 4runner Rock Sliders //////////////

T4R5-RSBO-KKOT ..............$639.99T4R5-RSBO-KKOT-DOM .....$739.99T4R5-RS-SKID .....................$249.99

T4R5-RSBO .........................$599.99T4R5-RSBO-DOM ................$699.99

5th gen 4Runner High Clearance Front Receiver Hitch //////////////////////////

Only CBI Offroad Fab can outfit your vehicle with the proper body armor for someone that is truly “Recreationally Insane!” Whether you’re into rock crawling, trail expeditions, or just good ol’ weekend fun our 5th Generation Toyota 4Run-ner front winch bumper provides the ultimate protection without sacrifice. Com-patible with factory fogs. Install time: 4 hrs –Optional Powder coat +$175

T4R5 Front Bumper //////////////////////////

T4R5-FB ...............................$999.99-PRO (aluminum) ..............add $300.00

T4R5-FB-CGP ....................$1099.99-PRO (aluminum) ..............add $300.00

T4R5-FB-FGP .................... $1199.99-PRO (aluminum) ..............add $300.00

The 5th Gen. 4Runner rear bumper package is the best that CBI Offroad Fab offers to take your 4Runner to the next level. This package offers specifically designed components with the true “recreationally insane” enthusiast in mind. It gives your 4Runner the best in looks and vehicle protection money can buy! Receiver hitch included (not load rated). Install time: 4 hrs –Optional Powder coat +$175

T4R5-RB .............................$1299.99

*Fits 10-13 only

*Fits 10-13 only

*Fits 10-13 only

4Runner

2010-present

5TH GEN4Runner

2010

-pre

sent

5TH G

EN

50 lbs

105 lbs

115 lbs

130 lbs

T4R5-RB-PKG ....................$1949.99Install time: 7 hrs –Optional Powder coat +$225

130 lbs

200 lbs


Bare Metal

Bare Metal

Bare Metal

Bare Metal

Bare Metal

96 lbs 94 lbs

Mount a winch to your 5th gen 4Runner while still main-taining the factory bumper and look. Cutting required to mount the fairlead. Fitment for non-integrated solenoid winches. Comes powder coated black. Install time: 4 hrs T4R5-HWM ............................................... $449.99

Hidden Winch Mount ////

55 lbs

See pg 34 for NEW swing arm design (Bolt on Rock Slider skid)



CBI Standard Swing Arm //////////////////////////Swin

g A

rmCB

I OFF

-ROA

DSwin

g A

rmCBI OFF-ROAD

• Hi-Lift Mount

• 3 Bearing Spindle

Optional Accessories //////////////////////////

• Locking De-Sta-Co Latch

The ultimate Overland accessory for every offroader is a CBI Swing Away Tire Carrier. Take everything with you from your oversized spare tire, to a hi-lift jack, fuel can options (including Rotopax’s) and even conveniences like a fold down table and telescopic camp light! The CBI Swing Away Tire carrier can be added to any rear bumper we manufacture and adds a lot of storage space and functionality to your Overland or offroad vehicle. The swing arm is designed to be very strong to hold up to offroad abuse and user friendly for the whole family.

• RotopaX Mount

• License Plate Mountincludes license plate light

• Adjustable Tire Mount

• Locking Pull Pin

Dual Can CarrierDUAL-CC ........ $189.99

Single Can CarrierSINGLE-CC .... $169.99

Camp TableSA-CT ............. $175.99

Telescopic Light MountSA-CL ............. $125.99Max Trax mounts Available

Shovel MountSA-SHOVEL ..... $69.99

Axe MountSA-AX ............... $69.99

• Can Carrier Mount

All optional accessories come powder coated black.

4 Galon Rotopax mountRP-4G-MOUNT ..................... $74.99

Dual Swing ArmDUAL-SA ........... add $300.00


Actual products may differ slightly from product images Actual products may differ slightly from product images//////////////////////////WranglerJK-JKU

JK-JKU Sliders ////////////Our Jeep JK-JKU Ditch Light Brackets give you the ability to mount aftermar-ket lights on the lower A-pillar. Available in single or dual application. Sold in pairs. Comes powder coated black. Install time: .5 hrs

JK-JKU Ditch Light Brackets ///////

JK-DDLB ...................... $59.99JK-SDLB ...................... $34.99

Jeep JK-JKU Sliders two piece design provides ample protection for both the rocker panel as well as the undercarriage of your Jeep. The slider can double as a step and is formed from 3/16” plate steel and 1/8” DOM tube for superior protection. Installation Requires drilling body panels and install-ing nut-serts. Install time: 4.5 hrs –Optional Powder coat +$175

JK-LBD .................................$149.99

The CBI Light Bar Bracket is great option for mount-ing a 50” light bar on your Jeep JK. Made from 3/16 steel, this bracket offers a sturdy mounting point. The CBI Light Bar Bracket utilizes the factory windshild hinge hardware for a clean easy install. Comes powder coated black. Install time: .75 hrs

JK-JKU Light BarBrackets ///////

Wra

ngle

rJK

-JKU

Wra

ngle

r2007-2016

JK-JKU

2007

-201

6

JK-HRS (steel) .........................................$799.99JK-HRS-PRO (aluminum) .......................$1024.99

125 lbs (steel)

70 lbs (aluminum)

Bare Metal



Lite weight Jeep JK-JKU bumpers are designed with the extreme off roader in mind. With maximum clearance and better approach angles, perfect for rock crawlers. We’ve also added a winch mount. As well as mounts for your factory fog lights. Install time: 3 hr –Optional Powder coat +$150

JK-JKU Front Bumper /////////////////////

JK-FB-HYRB ........................$749.99

JK-FB-MID ............................$699.99

JK-FB-FULL ..........................$749.99 JK-RB-PKG ....$1299.99

The JK rear bumper provides a greatly increase departure angle and clearance in the rear along with an integrated receiver hitch. Recovery points mount directly off of the frame and the mounting surpasses all other manufac-tures in strength and reliability. That is what we are known for at CBI! Install time: 1.5 hr –Optional Powder coat +$150

JK-JKU Rear Bumper ////////////////////W

rangle

rJK

-JKU

Misc / D

IYCBI OFF-ROAD

2007

-201

6

85 lbs

87 lbs

97 lbs

Install time: 5.5 hr –Optional Powder coat +$200

75 lbs

135 lbs

JK-RB ............ $699.99

Bare Metal

Bare Metal

Bare MetalBare Metal

Bare Metal

DIY 1st Gen 4Runner Front bumper ///T4R1-DIY-FB ................................... $424.99T4R1-DIY-CGG (Center Grill Guard) ....... $34.99T4R1-DIY-HP (Headlight Protection) ........ $44.99

Save money by building your own CBI bumper for your early model Toyotas. We provide all of the mounting hardware and parts needed to build your new bumper. All of the parts are cut and bent to fit together without difficulty. * Center grill guard (-DIY-CGG) and Headlight protection (-DIY-HP) sold separately.

DIY 2nd Gen 4Runner Front bumper ///T4R2-DIY-FB .................................. $424.99T4R2-DIY-CGG (Center Grill Guard) ...... $34.99T4R2-DIY-HP (Headlight Protection) ....... $44.99

DIY Toyota Pickup Front bumper ///TP1-DIY-FB ......................................... $424.99TP1-DIY-CGG (Center Grill Guard) ............. $34.99TP1-DIY-HP (Headlight Protection) .............. $44.99

DIY Toyota Pickup Front bumper ///TP2-DIY-FB ...........................................$424.99TP2-DIY-CGG (Center Grill Guard) ...............$34.99TP2-DIY-HP (Headlight Protection) ................$44.99

DIY Bumpers /////////

(1984-1989)

(1990-1995)

(1984-1988)

(1989-1995)

Ditch Light Brackets //////////////////

Lexus GX470 /// (2003-2009)LGX-DLB ................................ $59.99

Ford F150 / Raptor /// (2010-2016)FD-RPTR/F150-DLB .............. $59.99

2nd Gen Tundra /// (2007-2016)TT-DLB ................................... $59.99

200 Series Land Cruiser ///200LC-DLB ............................. $59.99

Polaris RZR ///RZR-DLB-SGL ........................ $39.99RZR-DLB-DUAL ..................... $59.99

Ditch Light Brackets give you the ability to run aftermarket lights on the hood of your vehicle. Comes powder coated.

2nd Gen Tundra Rock Sliders are abolt on application with top plating.

TT-RS ................................... $799.99

2nd Gen Tundra Sliders /////////



CBI-SBHAT ....................................... $23.99

//////////////////////////ApparelCBI OFFROAD

CBI-MBHAT-HOR ............................. $23.99CBI-MBHAT-VERT ............................ $23.99


CBI Mesh Back Hats /////////////////////

CBI Twill/Mesk Snapback Hats /////////////////////

Sizes:OSFALogo available in horizontal or verticalAdditional Features: Contrast trucker mesh back. Matching plastic snap. Hard buckram. Matching undervisor.Contents:47% Cotton / 25% Polyester / 28% Nylon

Colors: Brown, Green, Orange, Blue

Colors: Black/Black, Black/Grey, Lite Blue/Grey, Pink/Grey, Green/Grey, White/Grey

Sizes:OSFACotton twill front panels and visor with mesh back panels; ProCrown with buckram-fused front panels and ProStitching; pre-curved PE visor with eight rows of stitching.Contents:47% Cotton / 25% Polyester / 28% Nylon

Horizontal logo

Vertical logo


CBI Pullover Hoodie ///////////////////// CBI Rig Tee /////////////////////Color: Blue (White Logo) • Gray (Red Logo)

Hoodie-TT .........................................$49.99 (+$5 XXL)

Sizes: SM MD LG XL XXLPullover hooded sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. See color selection in photos above.• 8.5 oz (280 gm) cotton/polyester blend fleece• 100% cotton 20 singles face yarn• jersey lined hood• split stitch double needle sewing on all seams• twill neck tape• 1x1 ribbing at cuffs & waistband• metal eyelets• standard fit

TEE-OLJEEP ....................................$19.99 (+$2 XXL)TEE-OLT4R ......................................$19.99 (+$2 XXL)TEE-OLTACO ...................................$19.99 (+$2 XXL)

CBI Rig Tee /////////////////////Color: Black• Army Heather

CBI-TEE-BLK ...................................$19.99 (+$2 XXL)CBI-TEE-GREEN .............................$19.99 (+$2 XXL)

Sizes: SM MD LG XL XXL Tubular spec designed to have a slimming look in a unique bi-blend yarn that is premium spun combed cotton/polyester blend. Polyester has a natural wicking ability (taking perspiration away from the body), this is enhanced by our propriety dyeing process resulting a luxurious soft hand that will keep you comfortable in all conditions. A great t-shirt for the active lifestyle be it running, walking, hiking, yoga or simply having fun!

Notes /////////////////////


Colors: charcoal • army heather • navy heather • royal

Sizes: SM MD LG XL XXL Tubular spec designed to have a slimming look in a unique bi-blend yarn that is premium spun combed cotton/polyester blend. Polyester has a natural wicking ability (taking perspiration away from the body), this is enhanced by our propriety dyeing process resulting a luxurious soft hand that will keep you comfortable in all conditions. A great t-shirt for the active lifestyle be it running, walking, hiking, yoga or simply having fun!

Jeep 4Runner Tacoma

CBI Off RoadToll Free: 866.522.0697208.528.0664792 East Iona Rd.Idaho Falls, ID 83401

Download (PDF, 2.69MB) - CBI Offroad - Tire - …€¦ · Actual products ma differ slightl from...

Documents

Transcript of Download (PDF, 2.69MB) - CBI Offroad - Tire - …€¦ · Actual products ma differ slightl from...