Double Loop Wire Ties

P.O. Box 801178

Coto Laurel, Puerto Rico 00780-1178

Tel: (787) 843-2522 Tel-Fax: (787) 843-2515

E-mail: [email protected]

PRODUCT LIST & SPECS “WE WORK WITH INTERNATIONAL STANDARDS”

Double Loop Wire Ties Double Loop Wire Ties If you have a requirement for Loop End Wire Ties, look no further. From 3" to 20", 16 &17 Gauge, in a variety of finishes, we manufacture them all. Please refer to our Bar Tie Table for determining what tie length is recommended for tying various rod sizes. Black Annealed Wire Ties are made of dead-soft annealed wire - pliable, yet tough; easy to twist, but hard to break. Some of the many industries presently using the Black Annealed ties are: Construction, Pre-Cast and Pre-Stressed, Bagging and Bundling, Foundries, Carpet & Textile, Fencing, Paper and packaging. PVC Coated A dead-soft annealed core, surrounded by Poly Vinyl Chloride. Used for tying epoxy-coated rebar, bundling, fertilizer or chemical bags and anytime you need cushioned wire with added protection against corrosion, salt or abrasives. Galvanized Annealed The same strength as our others, but made from corrosion resistant zinc-coated wire. This is the tie with the long life for pre-stressed concrete, marine use, scallop bags, gabion boxes and any application

where length of service is important.

P.O. Box 801178

Coto Laurel, Puerto Rico 00780-1178 Tel: (787) 843-2522 Tel-Fax: (787) 843-2515


Wire As a manufacturer of steel wire for wire products, we are equipped to manufacture custom orders to your specifications. Our large in stock supply, custom capabilities, and straighten and cut services enable us to be your full service industrial steel wire manufacturer. “Don’t settle for less for your wholesale galvanized wire! Puerto Rico Steel Products provides us with excellent customer

service and Fast delivery From basic steel wire and black annealed wire, to wholesale galvanized wire and straight and cut wire, Our Wire is used in many applications such as concrete reinforcement, decorative items, display racks, and tie wire.

Bright Basic and Hot Rolled Steel Wire

Ideal for all types of fabricating.

• SAE 1006/1008 low carbon plain steel • Diameter ranges from .098” to .400” Black Annealed Steel Wire Ideal for tying or forming, black annealed wire is a soft wire for easy bending. We batch anneal the wire in our atmosphere controlled furnaces for consistency.

• Diameter 0.059” Galvanized Wire

Puerto Rico Steel Products, commercialize Galvanized coated steel wire in different sizes and Zink coating grades.

• Diameters: 2.57mm to 4.00mm • Special order sizes and grades available with minimum

purchase

P.O. Box 801178



Deformed Wire

Bright basic steel wire manufactured with indentations. Common uses include grapevine training rods and concrete reinforcement. • Diameter sizes from 3mm to 10mm

Straight and Cut Service Our wire straightening and cutting service is available to all our customers whether the wire is provided by our customer, or purchased from us. The following sizes are easily accommodated: • Diameter sizes from 4mm to 11mm

• Lengths from 1mts to 8mts

Pencil Rod

Plain and deformed reinforcing rod for the construction industry. • Available in lengths from 10" to 50' • Common Grades 1006-1020 • 0.125" to 0.400" AVAILABLE COATINGS: Bright, Galvanized SIZES: Assorted

P.O. Box 801178



Bulk Nails

Puerto Rico Steel Products produces different sizes, shapes and finishes in our facility. Our nails meet or exceed ASTM F1667, ASTM A153 and ASTM C514 nail standards. Our focus is to add quality and value to all of our products. Puerto Rico Steel Products nails are produced to ensure maximum strength at all times. Our advanced technology and efficient production ensure consistent quality. Class D for use in ACQ treated lumber or where corrosion is an issue. See our Nail Reference Chart for more information. AVAILABLE IN:

50 lb cartons. Other packaging is available on request. Penny Size Chart:

P.O. Box 801178 Coto Laurel, Puerto Rico 00780-1178

Tel: (787) 843-2522 Tel-Fax: (787) 843-2515


Chain Link Fence

• Known for its strength and durability, chain-link is perhaps the most economical type of fencing available. Puerto Rico Steel Products manufacture a wide range of Sizes (or gauges) and coatings.

• Chain-link systems offer years of maintenance-free, long-lasting protection. They’re easy to install and provide a high level of security.

Material Specifications:

Chain-Link Fabric Coating: HDG Commercial , Type 1, Class3 , Class 5 / PVC HDG Gauge From 6 to 12 Mesh 2" , 2 ½” , 2 3/8” Heights 3’, 4’ ,5’,6’,8’, 10’& 12’ Selvage Knuckle-Knuckle (KK) or Barb-Knuckle (BK)

P.O. Box 801178



Chain Link Fabric Mesh and Wire Gauge Configurations with Wire Break Load

Mesh Size 6 gauge 9 gauge 11 gauge 10 gauge 11 1/2 gauge

Inches (mm) 0.192 in. (4.88 mm)

0.148 in. (3.76 mm)

0.120 in. (3.05 mm)

0.132 in. (3,35 mm)

0.113 in. (2.87 mm)

2” S, HI HI, I, C, R ,T NM NM NM

2 3/8” S, HI HI, I, C, R C ,R R R

2 ½” S, HI I, C ,R R R R

Wire Breakload lbf

2170 1290 850 750 750

Wire Breakload N

9650 5740 3780 3340 3340

[2” 9 gauge is the most specified mesh for commercial and industrial applications]

General Applications: C = Commercial I = Industrial HI = Heavy Industrial R = Residential T = Tennis court

S = Security HS = High Security NM =Not Manufactured P = residential swimming pool fabric

Polymer coated wire is available in Gauge 12 ,11, 10 & 9.

_____________________________________________________________________________________

Chain link fabric height: The standard heights produced are 3 feet up to 12 feet. Some fabrics can be

special ordered in heights up to 20 feet.

Chain link fabric selvage (top and bottom edge finish): Knuckled selvage refers to bending the two

adjacent pairs of wire back into a tight loop. Twist selvage refers to twisting the adjacent pairs of wire

into a close helix of the equivalent to three full twists. The twist selvage has two sharp points for the

purpose of enhancing security, for security applications the twist selvage can be specified for the top

and bottom selvage. For consumer safety consideration, chain link fabric having 2 inch mesh in heights

less than 72 inches and fabric having a mesh size less than 2 inches are manufactured having a knuckled

finish at the top and bottom, “K&K”. Chain link fabric having 2 inch mesh in heights 72 inches and

greater is manufactured having a knuckle finish at one selvage and a twist selvage at the other, “K&T”.

SAFETY ALERT: Specify K&K selvage for 2 inch mesh in heights 72 inches and greater for play area, parks,

play fields, ball fields, pools etc.

Ponce, Puerto Rico 00732

Tel: (787) 843

MANSONRY WALL REINFORCEMENT

Puerto Rico Steel Mill Galvanized Ladder

used to horizontally reinforce masonry walls with inside reinforcement; it is manufacture in 10ft. and 10.8”.

Important recommendations The Truss Reinforcement must be anchored to

Do not overlap any Flat Truss Reinforcement between armors.

Longitudinal wires should be covered with mortar joint over all their length.

Ladder Wire It is formed by two longitudinal smooth Is manufacture in 10ft. Mill Galvanized.

Ladder Wire Specifications.

DESIGN A

6 4”

8 6”

10 8”

We also manufacture special size

12”

MECHANICAL PROPERTIES

TENSION STRENGTH

YIELD STRENGTH

ELONGATION

NORM

500lf per Bundle

P.O. Box 7265 Ponce, Puerto Rico 00732-7265

Tel: (787) 843-2522 Tel-Fax: (787) 843-2515 www.prsteel.net

MANSONRY WALL REINFORCEMENT

Puerto Rico Steel Mill Galvanized Ladder Reinforcement is an electro-used to horizontally reinforce masonry walls with inside reinforcement; it is manufacture in

Important recommendations The Truss Reinforcement must be anchored to lineal or terminal armors.

Do not overlap any Flat Truss Reinforcement between armors.


Ladder Wire It is formed by two longitudinal smooth 9-gauge wires electro-welded with perpendicular 9Is manufacture in 10ft. Mill Galvanized.

Ladder Wire Specifications.

S

WALL WIDTH

4” 16” 6

6” 16” 8

8” 16” 10

We also manufacture special size ladder From 2” to


= 5700 kg/cm2

= 5000 kg/cm2

=6% en 10 diámetros

= ASTM A-82

-welded armor used to horizontally reinforce masonry walls with inside reinforcement; it is manufacture in

lineal or terminal armors.


welded with perpendicular 9-gauge wires.

Truss Reinforcement Formed by 2 longitudinal 9 Is manufacture in 10ft. Mill Galvanized.

Truss Reinforcement Specification.

DESIGN A

4 2”

6 4”

8 6”


TENSION STRENGTH

YIELD STRENGTH

ELONGATION

NORM

Important characteristics of Truss Reinforcement The wire diagonal when being soldier by the internal face of the longitudinal wires in its same plane

provides saving of presents/displays overlapping cross wires and with the disadvantage of the excellent ends.

P.O. Box 7265

Ponce, Puerto Rico 00732-7265 Tel: (787) 843-2522 Tel-Fax: (787) 843-2515

www.prsteel.net

Truss Reinforcement Formed by 2 longitudinal 9-gauge smooth wires electro-welded with diagonal cross 9Is manufacture in 10ft. Mill Galvanized.

Truss Reinforcement Specification.

A

S

WALL WIDTH

2” 8” 4”

4” 8” 6”

6” 8” 8”


= 5700 kg/cm2

= 5000 kg/cm2

=6% en 10 diámetros

= ASTM A82

Important characteristics of Truss Reinforcement The wire diagonal when being soldier by the internal face of the longitudinal wires in its same plane provides saving of mortar joint against the conventional Flat Truss Reinforcement that presents/displays overlapping cross wires and with the disadvantage of the excellent ends.

A more comfortable and safe handling,

To leave the rubblework walls I pretend,

Emboss without no problem of mortar meetings

To place the direct plaster finished one.

2515

welded with diagonal cross 9-gauge wires.

The wire diagonal when being soldier by the internal face of the longitudinal wires in its same plane mortar joint against the conventional Flat Truss Reinforcement that

presents/displays overlapping cross wires and with the disadvantage of the excellent ends.

Snapties Snap Ties are manufactured with hot integral heads. Snap Ties have a nominal 1" breakback. Coating the tie ends with wax will aid in breakback operation.

Standard Snapties provide a safe working load of 2,250 lbs. adequate end clamps are required to develop safe working loads.100 pieces per

carton.

No. Size Wt/Ctn (lbs)

SNAPTIE - STANDARD

Snaptie has round heads, anti-turn deformations and 1" breakback. The Snaptie is available equipped with either

plastic spreader cones or loose neoprene washers. For additional rust and corrosion resistance, the Standard Snaptie is available

in HDG steel.

NOTE: The plastic cones, furnished from high impact polystyrene, are available in the sizes 1x1. Cones are preferred over a loose washer tie

since it covers the break back portion of the tie. Such guarantee of break back is not available with the loose washer tie. When removed the

plastic cone also provides a better cavity for grouting purposes. Attempting to breakback any tie, before the concrete has been allowed to

properly set, may result in the entire tie turning freely in the wall, making the normal breakback procedure no longer possible. Washer style

snapties should be removed before 24 hours of concrete pour.

Safe Working Load (lbs) 2,250

Safe working load is based on an Approximate 2:1safety factor.

SNAPTIE WATERSEAL

All Snapties are available with a neoprene washer to aid in preventing

moisture seepage along the tie wire. Specify this feature when ordering a snaptie product.

Steeldeck Steeldeck is a floor structure construction system , consisting of a pre-formed steel sheet (steel deck) and a concrete slab cast over it in a monolithic way, forming a composite steel floor deck. Steeldeck Construction System complies with SDI specifications.

spfor con-struc-tion and main-te-nance loads.

Steel Deck spans are based on a max-i-mum stress og 26,600 psi or a max-i-mum deflec-tion of L/ 240 under a 200 lb. con-cen-trated load applied at mid- span over a 1′-0″ wide sec-tion of deck. (SDI Criteria)

Type “B” (wide rib) deck pro-vides maximum structural load capacity through an efficient profile design and allows the use of 1- inch thick rigid insu-la-tion boards. The side lap of this prod-uct per-mits easy instal-la-tion and its nestable feature eliminates the need for die- set ends. • Man-u-fac-tured In Acoorance with Steel Deck Institute • In accor-dance eith Fac-tory Mutual Systems • In accor-dance with Under-weit-ers Laboratories • Com-ply with Health Depart-ment Deck for Sound Con-trol with the use of

FiberGlassInstitution

ROOFING (CORRUGATED ROOF PANEL)

Galvanized Steel Corrugated Roof Panel is an inexpensive option used in a

variety of applications on residential, agricultural and industrial buildings.

The corrugated panels are generally used on commercial buildings and

commonly used on roofs for barns and sheds.

26” 33

Properties Units 0.018 (0.45 mm) 0.018 (0.45 mm)

Overall Width in 26 (660 mm) 33 (838

mm)

Weight lb/ft 1.6 2.0

Length** ft

6, 7, 8, 9, 10, 11, 12, 14, 16, 18, 20 & 24 (1.82, 2.13,

2.44, 2.73, 3.05, 3.35, 3.66, 4.27, 4.88, 5.49 , 6.10 &

7.20m)

I

* According to ASTM A 653 / A 924 standard specifications

** Special orders upon request

Welded Wire Reinforcement

Welded wire reinforcement also named as Welded wire mesh is a prefabricated reinforcement consisting of parallel series of high-strength, cold draw or cold rolled wire welded together in square or rectangular grids. Each longitudinal wire is electrically-welded to traverse steel wires at square angles therewith, also spaced in a parallel pattern between each other, thereby forming wire meshes. Wire meshes are elaborated following the specifications ASTM A-1064 standards.

SAVING ADVANTAGES

Welded Wire Reinforcement (WWR), with its higher yield strength and other material characteristics, can be significant savings on projects through the proper use of WWR. These savings come in material and labor costs. Material costs savings (up to 25%) come from less material is needed, and labor savings (up to 50%) is due to less manpower and faster installation.

Puerto Rico Steel Products produces quality Welded Wire Reinforcement (WWR), in sheets and rolls, for the construction and pre-cast industries.

STANDARD ROLLS AND MATTS REINFORCEMENT

Puerto Rico Steel Products produces a broad range of standard welded wire reinforcement products in both rolls and sheets. When properly placed in concrete slabs on grade, helps reinforce the concrete after cracking and is a critical element in its performance. The wide variety of wire sizes (W1.4 to W/D10) and spacings that are available make it possible to furnish accurate cross-sectional areas of steel required to reinforce residential and light commercial slabs. Galvanized WWR are also produce

Our welded wire reinforcement A185 for smooth welded wire and A497 for deformed welded wire).

ROLLS AND MATTS WELDED WIRE

Puerto Rico Steel Products produces a broad range of standard welded wire reinforcement products in both rolls and sheets. When properly placed in concrete slabs on grade, helps reinforce the concrete after cracking and is a

ance. The wide variety of wire sizes (W1.4 to W/D10) and spacings that are available make it possible to furnish accurate

sectional areas of steel required to reinforce residential and light

Galvanized WWR are also produce.

Our welded wire reinforcement products conform to ASTM A1064 (replaces A185 for smooth welded wire and A497 for deformed welded wire).

Puerto Rico Steel Products produces a broad range of standard welded wire reinforcement products in both rolls and sheets. When properly placed in concrete slabs on grade, helps reinforce the concrete after cracking and is a

ance. The wide variety of wire sizes (W1.4 to W/D10) and spacings that are available make it possible to furnish accurate

sectional areas of steel required to reinforce residential and light

products conform to ASTM A1064 (replaces

Mesh Rolls

Style (W or D) Gauge Width / Length Unit Weight Packaged Bundles Truckload Quantity

6x6 W1.4/W1.4 10/10 5x200 199.75 14 Rolls 252

6x6 W1.4/W1.4 10/10 6x150 178.35 9 Rolls 288

6x6 W1.4/W1.4 10/10 5x150 149.81 9 Rolls 324

6X6 2.1/2.1 8/8 5x150 224.72 14 Rolls 210

6x6 2.9/2.9 6/6 5x150 310.31 7 Rolls 155

6x6 2.9/2.9 6/6 5x150 310.31 11 Rolls 155

Welded Wire Reinforcement Matts

Style (W or D) Gauge Width / Length Unit Weight Packaged Bundles Truckload Quantity

6x6 W1.4/W1.4 10/10 8x20 31.39 100 Sheets 1400

6x6 W1.4/W1.4 10/10 8x15 23.54 100 Sheets 1800

6x6 W1.4/W1.4 10/10 8x12'6" 19.62 100 Sheets 1800

6x6 W1.4/W1.4 10/10 5x10 9.99 100 Sheets 3000

6x6 2.1/2.1 8/8 8x20 47.08 50 Sheets 1000

6x6 2.1/2.1 8/8 8x15 35.31 50 Sheets 1300

6x6 2.1/2.1 8/8 8x12'6" 29.43 100 Sheets 1500

6x6 2.1/2.1 8/8 5x10 14.98 100 Sheets 3000

6x6 2.9/2.9 6/6 8x20 65.02 50 Sheets 700

6x6 2.9/2.9 6/6 8x15 48.76 50 Sheets 950

6x6 2.9/2.9 6/6 8x12'6" 40.64 50 Sheets 1150

6x6 2.9/2.9 6/6 5x10 20.69 100 Sheets 2300

6x6 4/4 4/4 8x20 89.67 50 Sheets 500

6x6 4/4 4/4 8x15 67.26 50 Sheets 700

6x6 4/4 4/4 8x12'6" 56.05 50 Sheets 850

6x6 4/4 4/4 5x10 28.53 100 Sheets 1600

4x4 2.1/2.1 8/8 5x10 22.11 50 Sheets 2000

4x4 2.9/2.9 6/6 8x20 96.54 25 Sheets 475

4x4 2.9/2.9 6/6 8x15 72.4 25 Sheets 650

4x4 2.9/2.9 6/6 8x12'8" 61.14 25 Sheets 750

4x4 2.9/2.9 6/6 5x10 30.54 50 Sheets 1550

4x4 4/4 4/4 8x20 133.15 25 Sheets 350

4x4 4/4 4/4 8x15 99.86 25 Sheets 450

4x4 4/4 4/4 8x12'8" 84.33 25 Sheets 550

4x4 4/4 4/4 5x10 42.12 50 Sheets 1100

WWR Codes & Standards

A. Plain Welded Wire Reinforcement: ASTM A185, and as follows:

1. WWR Yield Strength: Provide minimum yield strength of 75,000 psi (515 MPa).

2. Wire used in the manufacturing of welded wire reinforcement conforms to ASTM A82.

B. Deformed Welded Wire Reinforcement: ASTM A497, and as follows:

1. WWR Yield Strength: Provide minimum yield strength of 80,000 psi (550 MPa).

2. Wire used in the manufacturing of welded wire reinforcement conform to ASTM A496.

C. Yield Strength: Min 72,800 psi

D. Weld Shear Strength: Min 35,000 psi

Concrete Pipe & Box Culverts WWR Mesh Rolls

Save time and money by using Welded Wire Reinforcement (WWR) in your precast pipe and

box culverts. WWR is a major ingredient of precast concrete pipe and precast concrete box

culverts because it provides an economical solution to your drainage problems.

WWR is available in large rolls or individual sheets that are rolled into reinforcing cages. The

savings in labor during the assembly of reinforcement plus the ability to meet

tight dimensional tolerances

WWR Mesh Rolls are made using both smooth (W) and deformed (D) wire. Been Produce with exact steel areas and precise designs, we can eliminate unnecessary stockpiling of steel materials and over steeling. Each order can be customized to meet the unique requirements of your concrete pipe manufacturing equipment, thereby eliminating waste.

Structural WWR Matts

(WWR)

WIRE MESH SIZE DESIGNATION:

Individual wire (plain and deformed) size designations are based on the cross-sectional area of given wire. The prefixes “W” and “D” are used in combination with a number. The letter “W” designates a plain wire and the letter “D” designates a deformed wire. The number following the letter gives the cross –sectional area in hundredths of a square inch. For instance, wire designation D6 would indicate a deform wire with a cross sectional area of 0.06 sq.in.

Since the engineer now the cross-sectional area of a wire and the spacing ,the total cross sectional area per foot of width can be easily determinate. For instance a D6 wire on 4 inch center would provide 3 wires per foot with a total cross sectional area of 0.18 sq.in. per foot of width.

STYLE & DIMENSIONS:

Spacing and sizes of wire in WWR are identified by “Style.” A typical style designation is:

8’x 20’ 6” x 12” W12 x W5

These denote a WWR Mesh Matt which:

Width of mesh matt: 8’

Length of mesh matt : 20’

Spacing of longitudinal wire of : 6”

Spacing of transversal wire of: 12”

Size of longitudinal wire of : W12 ( 0.12 sq.in.)

Size of transversal wire of : W5 (0.05 sq.in.)

SPECIFICATIONS:

Welded wire reinforcement covers the following ASTM specifications: ASTM 1046 ASTM A82, ASTM A185, ASTM A496, ASTM A497 Minimum mechanical properties: Tensile Strength: 80,000 psi Yield Strength: 70,000 psi Weld Shear Strength: 35,000 psi (D4 and Over) (Plain wire meshes are -5,000 psi than deformed wire mesh)

Finish & Coatings:

Plain WWR mesh is standard. Puerto Rico Steel can offer galvanized wire mesh made from HDG Wire before welding.

WELDED WIRE REINFORCEMENT

(WWR)

STANDARDS WWR MATTS (US MARKET):

REF# DIMENTIONS SPACING DIAMETER CONVERCIONS

PR8x20x6xD2.9 8’ x 20’ 6”x 6” D2.9 x D2.9 -----------

PR8x20x6xD3 8’ x 20’ 6” x 6” D3.0 x D3.0 #3@18”

PR8x20x6xD4 8’ x 20’ 6”x 6” D4.0 x D4.0 #3@15”

PR8x20x6xD5 8’ x 20’ 6” x 6” D5.0 x D5.0 #3@12”

PR8x20x6xD6 8’ x 20’ 6” x 6” D6.0 x D6.0 #3@10”

#4@18”

PR8x20x6xD9 8’x 20’ 6” x 6” D9.0 x D9.0 #4@12”

(Plain wire meshes are -5,000 psi than deformed wire mesh) Welded wire reinforcement covers the following ASTM specifications: A1046 ASTM A82, ASTM A185, ASTM A496, ASTM A497

Betonmatt

European B 500 Standards :

Welded Wire Fabrics / Beton Arme’

REF# DIMENTIONS SPACING DIAM WEIGHT PCS/BUNDLE

AC2x5x15x4 2Mts x 5Mts 15 x 15ctm 4.0mm 13.40Kgs 70Pcs

AC2x5x15x5 2Mts x 5Mts 15 x 15ctm 5.0mm 20.17Kgs 70Pcs

AC2x5x15x6 2Mts x 5Mts 15 x15ctm 6.0mm 29.00 Kgs 50Pcs

AC2x5x15x8 2Mts x 5Mts 15 x 15ctm 8.0mm 51.00 Kgs 30Pcs

AC2x5x15x10 2Mts x 5Mts 15 x 15ctm 10 mm 80.00 Kgs 20Pcs

WW Fabrics Btonmatt are made under the following Spects: B 500 T , B 500 S , NK 500 BT , B 500 AF , B 500 B , B 500 NA Minimum mechanical properties: Tensile Strength: Fs: >550N/mm2 Ductility: Rm/Re >1.05 and Agt >5 Yield Strength: Fy: >500N/mm2 Fs min = 0,25.Fy.An

Tubes & Pipes Puerto Rico Steel Products is leader in the manufacturing of high-quality steel pipe and tubing products in Puerto Rico. We currently produce Galvanized Square, Rectangular and Round Tubes. The sizes produced are in accordance with the American Society for Testing and Materials (ASTM). All our galvanized products strictly conform to the tube specification of ASTM A-787. All galvanized products are produced from prime high-quality raw materials. The outside diameter weld seam of each tube is re-metalized after the forming and high frequency welding process. The finished galvanized tube is cut to length in-line. Product suitable for multiple applications. Puerto Rico Steel Products produces galvanized tubing ranging in size from 3/4" square and rectangular through 2". Round galvanized sizes are available from 1" O.D. through 2" O.D.

PRODUCT THECNICAL DETAILS SHEET

Square and Rectangular Tubes

Galvanized Square and

Rectangular Tubing

Thickness Packing Unit

Weight

3/4 X 3/4" X 20' .033 120 6.60

3/4 X 3/4" X 20' .045 120 8.80

3/4 X 3/4" X 20' .054" 120 11.15

1 X 1" X 20' .033" 100 8.40

1 X 1" X 20' .048" 100 12.46

1 X 1" X 20' .054'' 100 14.39

1 X 1" X 20' .071'' 100 18.54

1 X 1" X 20' .125" 100 26.20

1 X 2" X 20' .048'' 60 18.73

1 X 2" X 20' .054'' 60 21.58

1 X 2" X 20' .071'' 60 28.20

2 X 2" X 20' .045'' 25 24.00

2 X 2" X 20' .054'' 25 28.44

2 X 2" X 20' .071'' 25 37.91

ROUND PIPES

Fence

Pipes

Thickness Packing Unit Weight

FT 1" X 20' .030'' 91 8.31

FT 1 1/4" X

20' .030'' 61 10.51

FT 1 1/2" X .036'' 61 14.42

20'

FT 2" X 20' .036'' 37 17.85

ASTM A787 TUBING

PUERTO RICO STEEL PRODUCTS CORP produces round electric resistance welded (ERW) metallic-coated carbon steel mechanical tubing to ASTM specifications A787), Type 2 and Type 4. ASTM A787 tubing is used in a variety of agricultural, industrial, transportation and industrial related end uses. For a complete listing of sizes produced, please

visit our PRODUCT THECNICAL DETAILS SHEET

A787 Type 2 ASTM A787 Type 2 welded mechanical tubing is produced using carbon steel that has been pre-coated with a thin layer of zinc while in coil form. A787 Type 2 tubing is often used in applications where rust resistance is critical and provides for extended durability than non-coated carbon steel.

A787 Type 6 ASTM A787 Type 6 welded mechanical tubing is produced using steel that has been pre-coated with a thin layer of a zinc-aluminum-magnesium alloy coating while in coil form as specified in ASTM A1046. Tubing produced to A787

Type 6 provides a high degree of corrosion resistance and an excellent surface appearance and is a bridge between stainless and hot-dip galvanized finishes.

Specification Notes • ASTM A787 covers carbon steel grades starting at 1008 up through

1021. Please visit our Finishes & Chemistries page for a listing of our standard chemistry capabilities.

• Physical testing (yield, tensile and elongation) is not required under A787. If there is a specific strength requirement for your application, please be sure to include at the time of inquiry as that will affect the chemistry required.

• ASTM A513 is a related mechanical tubing specification that covers non-metallic coated carbon and alloy steel tubing. Please refer to the ASTM A513 page for more information.

• For more detailed information on the A787 specification and to purchase a copy of it, please visit the ASTM website.

Glossary ASTM ASTM is the abbreviation for the American Society for Testing & Materials which is the governing body that publishes specifications that cover the ordering of steel, types of testing required and types of tubing produced among others. The ASTM website has a complete listing of specifications that you can search for more information. Chemical Properties Chemical properties are the mimimum and maximum limites of chemical elements as established by ASTM and SAE specifications. Coil Steel coils are sheets of steel that have been wound up by a steel mill. Large coils are slit or cut down to smaller widths desired in order to produce tubing. Hardness A mechanical property of steel that measures the resistance to indentation. Hardness is related to the maximum strength of steel.

ID ID refers to the inside diameter of the tubing. It is specified in inches and decimals of an inch. Mechanical Properties The mechanical properties of steel show the elastic and inelastic reaction of the steel when force is applied to it. Yield strength, tensile strength and elasticity are common mechanical tests performed. Also referred to physical properties. Minimum Wall Thickness The lowest value that steel can be measured at in order to ensure that it meets the corresponding ASTM specification for the coil or tube or customer requirement specified. It can be calculated by subtracting the minus tolerances from the nominal wall thickness. Nominal Wall Thickness The theoretical or stated single value given to the gauge or wall thickness of steel. OD is an abbreviation for outside diameter. It is expressed in inches, decimals of an inch and in metric. Ovality Ovality is the difference between the maximum and minimum diameters of any one section of a round tube as measured. Tensile Strength�Tensile strength - also referred to as "ultimate strength" - is a measure of the ability of steel to withstand a longitudinal stress, expressed as the greatest stress that the steel can stand without breaking. Tolerances�The allowable difference in measurements from a desired value between what the customer requests or what an ASTM specification calls out for. Examples of common tubing tolerances include OD, ID, wall thickness, chemical and length tolerances. �Tubing�Tubing is a non-standardized hollow shaped product manufactured to specific dimensional, chemical and mechanical properties. It is important to distinguish between the terms tubing and pipe. A tube is identifed by the OD size and wall thickness while a pipe is produced to nominal specifications. A 2" NPS schedule 40 "pipe" size would be described as 2.375" OD x .156" wall in a "tube" size. Yield Strength�Yield strength is the stress at which steel begins to exhibit a specified deviation from inelastic strain.

��

Double Loop Wire Ties

Documents

Transcript of Double Loop Wire Ties