D.O.T. APPROvED 12000 DRIP TORCH - Cascade Fire … Torch...12000 DRIP TORCH OPERATING INSTRUCTIONS...
2
12000 DRIP TORCH OPERATING INSTRUCTIONS FUEL Refer to your Agency or Bureau policy regarding the type of fuel mixtures to be used. STARTING Fill the torch, leaving a 2” space at top, which allows for fuel expansion. Do not fill near open flame or other ignion source. Wipe off outer surface of tank and handle. Remove discharge plug and insert in blind socket. Open breather valve two full turns. Tip torch forward, allowing fuel to wet igniter. Light igniter, drip torch is ready to use. STORAGE AFTER USE Exnguish igniter by allowing it to burn out. Aſter igniter has cooled completely, remove lock-ring and reverse the spout inside the tank. Replace lock-ring securely. Insert the sealing plug, from the blind threaded socket, into the spout opening. Close the breather valve. D.O.T. APPROvED mEETS USDA SPEC 5100-614A JUNE 11, 2009 CASCADE FIRE EQUIPmENT COmPANY Use of firing equipment should be restricted to trained, experienced personnel, who will take precauons to avoid danger to themselves and others. Keep torch in good order, inspect periodically and replace worn or missing parts. Handle all petroleum products with the same precauons as when handling gasoline. Before using inspect all parts of Drip Torch to ensure the Drip Torch is in good working order. Look inside tank and make sure breather tube is secure. Before lighng, turn Drip torch over to ensure that breather tube, tank collar gasket, spout and fuel trap, are not leaking fuel. Fuel should only discharge from nozzle on to the igniter. If leaks are detected, remove Drip Torch from service unl unit can be repaired. CAUTION
Transcript of D.O.T. APPROvED 12000 DRIP TORCH - Cascade Fire … Torch...12000 DRIP TORCH OPERATING INSTRUCTIONS...
12000 DRIP TORCHOPERATING INSTRUCTIONS
FUEL
Refer to your Agency or Bureau policy regarding the type of fuel mixtures to be used.
STARTING
Fill the torch, leaving a 2” space at top, which allows for fuel expansion. Do not fill near open flame or other ignition source. Wipe off outer surface of tank and handle. Remove discharge plug and insert in blind socket. Open breather valve two full turns. Tip torch forward, allowing fuel to wet igniter. Light igniter, drip torch is ready to use.
STORAGE AFTER USE
Extinguish igniter by allowing it to burn out. After igniter has cooled completely, remove lock-ring and reverse the spout inside the tank. Replace lock-ring securely. Insert the sealing plug, from the blind threaded socket, into the spout opening. Close the breather valve.
D.O.T. APPROvED
mEETS USDA SPEC 5100-614AJUNE 11, 2009
CASCADE FIRE EQUIPmENT COmPANY
Use of firing equipment should be restricted to trained, experienced personnel, who will take precautions to avoid danger to themselves and others. Keep torch in good order, inspect periodically and replace worn or missing parts. Handle all petroleum products with the same precautions as when handling gasoline.
Before using inspect all parts of Drip Torch to ensure the Drip Torch is in good working order. Look inside tank and make sure breather tube is secure. Before lighting, turn Drip torch over to ensure that breather tube, tank collar gasket, spout and fuel trap, are not leaking fuel. Fuel should only discharge from nozzle on to the igniter. If leaks are detected, remove Drip Torch from service until unit can be repaired.
CAUTION
12010
12012
12011
12013
CASCADE FIRE EQUIPmENT COmPANYPO Box 4248 n Medford, OR 97501
800-654-7049 n 541-779-0394 n Fax 541-779-8847www.cascadefire.com n [email protected]
DRIP TORCH REPLACEmENT PARTS
For ordering information, contact:
12017
12002
1200312004
12005
12006
1200712008
12009
12016
12018
12022
12023
12024
REPLACEmENT PARTS FOR DRIP TORCHES purchased before Aug. 2007:
DRIP TORCH
REPLACEmENT PARTS
PART DESCRIPTION
12002 Tank Cover
12003 Check Valve Ball
12004 Check Valve Seat
12005 Outlet Screen
12006 Discharge Sealing Plug
12007 Discharge Plug Gasket
12008 Discharge Plug Chain
12009 Spout and Fuel Trap
12010 Nozzle 3/32 Bore
12011 Igniter Clamps (Pair)
12012 Igniter Clamp Screw
12013 Igniter
12016 Tank Collar Gasket
12017 Tank Cover Lockring
12018 Chain Screw
12022 Breather Tube Assembly
12023 Igniter
12024 Nozzle
12010
12012
12011
12013
