DN 110x90 - AIRFIT · DN 110x90 DN 125x90 DN 160x90 ... tested according to DIN 4102-B2, EN...

Branch saddle

PP angle hose

Universal pump angle

Universal pump nipple

Hose nipple

Ultra-short reducer

DN 110x90

DN 125x90

DN 160x90

DN 50x40

DN 110x90DN 110x90

DN 40

What’s new?

Because it’s easier!

12

Item no. 21057KS

Item no. 21048KS

Item no. 21086KS

When exceeding the max. pipe wall thickness, a safety set is required. DN 90 = 3.0 mm DN 110 = 3.2 mm DN 125 = 3.2 mm

Item no. 29099AZ

Set is suitable for the DN 90-125

Accessories: Safety set

Simple installation: Drill Ø 57 mm hole, deburr, fi t screw-fi t branch and tighten. AND THAT’S IT!

Accessories: Circle cutter Ø 57 mm HSS bimetallic, complete, for plastic and metal. When working on metal pipes, use lower speed and cutting oil.



Dimensions – Item no.: 90 / 40 Item no. 29040AZ

90 / 50 Item no. 29050AZ

110 / 40 Item no. 21040AZ

110 / 50 Item no. 21050AZ

125 / 40 Item no. 22540AZ

125 / 50 Item no. 22550AZ

Item no. 20000KS

Accessories: Circle cutter Ø 57 mmcomplete, for plastic

Easy-to-assemble screw-fi t branch

Simple installation: Drill hole, deburr, place the branch saddle on the pipe, fi t the hose clamps and tighten lightly. AND THAT’S IT!

made inGermanymade inGermany

2

Branch saddle set - suitable for all pipe materials with matching exterior diameter

The set consists of: 1x branch saddle, 1x seal, 2x stainless steel hose clamps

• Easy to install • Time-saving • Hot-water resistant

Item no. 28755SA

Item no. 28165SA

Set DN 75x50

Set DN 160x50

Item no. 28119SA

Item no. 28169SA

Item no. 28129SA

Set DN 110x90

Set DN 125x90

Set DN 160x90

DN 75x50

SML 70 + 80


DN 75x50

1x branch saddle, 1x seal, 2x stainless steel hose clamps

HT 110

DN 110x90

DN 110x90

Clay pipe 110

Fire performance: tested according to DIN 4102-B2, EN 13501-1-E, EN 11925-2


1

Dimensions – Item no.:

DN 200x160 Item no. 160200KA

DN 250x160 Item no. 160250KA

DN 315x160 Item no. 160315KA

DN 400x160 Item no. 160400KA


The solution! Time saving of at least 1 hour.

Adhesive branch made of PVC-U

• incl. 2 cable ties up to DN 160

• incl. 2 cable ties up to DN 160DN 160x125

Accessories: Outfl ow DN 110 Circle cutter Ø 106 mm

Item no. 20106KS

Accessories: Outfl ow DN 160 Circle cutter Ø 152 mm

Item no. 21152KS

The problem: Later installation of branches or cleaners means you need extra room for ➊ two sliding sleeves ➋ branch connection ➌ pipe connector ➍ and room to advance the sliding sleeves.

The solution:

DN 160x110

Drying time at least 20 minutes.

1 2 3

4 5 6

• Mark hole • Cut with jigsaw or angle grinder • Clean pipe and fi tting with PVC-U solvent

!!! Apply a thick strand of adhesive of about 4 mmto the adhesive fi tting.Ass

emb

ly i

nst

ruct

ion

s fo

r ad

hes

ive

bra

nch

45°

:

Accessories: 10000KS

Adhesive set consisting of: • PVC-U adhesive 125 ml • PVC-U solvent 125 ml • Cloths

Item no. 10000KS

Align the adhesive fi tting on the pipe, press into place and fi x with the supplied cable ties. Remove any excess adhesive.

Observe the instructions of the glue manufacturer.

The

cabl

e tie

s ar

e us

ed a

s an

ass

embl

y ai

d.

➊ ➊➌➋

The benefi ts: • Two-thirds less earthworks

required.• No need for sawing twice.• No more leakages.• Two sliding sleeves are no

longer necessary.

Huge time savingsDimensions – Item no.:

DN 110x90 Item no. 451190KA

DN 160x125 Item no. 456125KA

DN 200x125 Item no. 452125KA

DN 200x160 Item no. 452160KA

DN 250x125 Item no. 452512KA

DN 250x160 Item no. 452516KA

DN 315x125 Item no. 453112KA

DN 315x160 Item no. 453160KA

DN 400x125 Item no. 454125KA

DN 400x160: Item no. 454160KA

DN 500x125 Item no. 455125KA

DN 500x160 Item no. 455160KA


DN 125x110 Item no. 130110KA

DN 160x110 Item no. 165110KA

DN 110 x 90

Item no 51190KA

Adhesive clips branch 45°For 45° branches,

the inlet opening is cut out with a jigsaw or an angle grinder.

PVC-U

DN 110

DN 90

3

Accessories: Circle cutter Ø 106/152 mmDrilling depth 47 mm HSS bimetallic, complete,for plastic and metal. When working on metal pipes, use lower speed and cutting oil.


213 mm

EN 14814 - EN 14680Also suitable for PVC-U pressure pipes.

Minimum required space for DN160x110 is 800mm


12


DN 200 Item no. 20010KR




4DN 160 DN 125 DN 110

Cleaner connection 125 or 110 green, made of PP

Cleaner connection125 or 110 grey, made of PP

Cleaner connection 125 or 110 stainless steel

Flush mounting in courtyard or lawn

The real all-rounder cleaner connection for internal and external use.

CO

NC

RETE

< Cellar fl oor

UV stabilised

Item no. 50300RVGU

Item no.160125IR*Fire performance: tested according to DIN

4102-B2, EN 13501-1-E, EN 11925-2

Wal

l ins

talla

tion

Item no. 50300RVA4 * Item no. 50300RVGNItem no. 50300RVGU *


PVC-U

• incl. 2 cable ties up to DN 160

Glue cleaner

Drying time at least 20 minutes.

1 2 3

4 5 6

• Drill hole • Deburr • Clean pipe and fi tting with PVC-U solvent

!!! Apply a thick strand of adhesive of about 4 mm to the adhesive fi tting.

Ass

emb

ly i

nst

ruct

ion

s fo

r g

lue

clea

ner

s:


Align the adhesive fi tting on the pipe, press into place and fi x with the supplied cable ties. Remove any excess adhesive.

Observe the instructions of the glue manufacturer.

The cable ties are used as an assembly aid.

Can be driven over

Accessories: Access opening ø 110 Circle cutter Ø 110 mm

Item no. 20110KS

Accessories: Access opening ø 160 Circle cutter Ø 152 mm

Item no. 21152KS




Accessories: Circle cutter Ø 110/152 mmDrilling depth 47 mm HSS bimetallic, complete, for plastic and metal.When working on metal pipes, use lower speed and cutting oil.


CO

NC

RETE

The original!

5

The typical problem on almost every construction site:

Time required: approx. 28 min.

1. Cut pipe fl ush to the ground with angle grinder.

2. Insert Airfi t waste water interior reducer – save time and money.

Time required: approx. 1 min.

For underground pipes

20 times quickerinstallation!

Airfi tWaste water interior reducer

1. Mortise the drain pipe in the fl oor plate to the next sleeve with the caulking hammer.

2. Use force to pull out the drain pipe.3. Clean sleeve and sealing element.4. Insert reducer.5. Measure the pipe connector.6. Cut the pipe connector to size.7. Insert the pipe connector8. Remove rubble.9. Reseal the fl oor plate with concrete.

The only approved waste water interior reducers for horizontal installation that DO NOT NEED A SLEEVE!

DN 160/125*Item no. 160125IR

DN 200/160*Item no. 200160IR

DN 160/110*Item no. 160110IR

DN 160/50*Item no. 16050IR


Conventional

The only approved waste water interior reducers for horizontal installation.DN 75/50*Item no. 7550IR

DN 90/50*Item no. 9050IR

DN 110/50*Item no.. 11050IR

DN 110/75*Item no. 11075IR

DN 90/75*Item no. 9075IR

Item no.10850IR

DN 125/110Item no. 125110KG

DN 160/110Item no.160110KG

DN 160/125Item no.160125KG

DN 200/160Item no.200160KG

DN 108/50* eccentric

For thick-walled pipes with an internal diameter of 101–103 mm. Suitable for ...

... Wavin: SiTech pipeDyka: PVC-U-Ultra-3

Poloplast: POLO-KAL-NGPiplife: Master 3 Valsir: Tri-Plus

Geberit: Silent-PPGeberit: Geberit-PE

KG 2000, etc.

!INFO! Friendly information from the managing director of Airfi t, Josef Zimmermann, master gas and water pipe installer and central heating and ventilation engineer.

Tested and approved by DIBt Z-42.1-366 Suitable for underground waste pipes (DIN EN 1401-1) and HT pipes (DIN EN 1451-1)

*Fire performance: tested according to DIN 4102-B2, EN 13501-1-E, EN 11925-2

DN 110/90*Item no.11090IR

DN 125/110*Item no. 125110IR

seal accordingto EN 681

The general construction approval from the DIBt Berlin verifi es the usability of our reducers within the meaning

of the federal state building regulations.


12 6

Cleaning and access opening; water- and smellproof. For wall, containers, machine covers, and much more.

129 142109

121

129 138 109 135

Circle cutter Ø 110 mm required. (Fig. p. 4)Circle cutter Ø 121 mm required. (Fig. p. 11)


Airfi t branch plug • Waterproof, water column of at least 5 metres • Space-saving

DN 110/110 DN 110/90 DN 110/75 DN 110/50Item no. 199110SA Item no. 199090SA Item no. 199075SA Item no. 199050SA

Item no. 20110KSItem no. 20121KS

6

1 332 4 5 6

• 2) Drill hole Ø 121 mm • 3) Deburr • 4) Insert • 5) Insert & tighten screw • 6) Tighten cover READY!


Tested and approved by the DIBt Z-42.1-394

Fire

per

form

ance

: te

sted

acc

ord

ing

to

DIN

410

2-B

2, E

N 1

3501

-1-E

, EN

119

25-2

Z-42.1-394 Z-42.1-394 Z-42.1-394

Cleaner screw fi tting Cleaner fl angeItem no. 51300RFItem no. 51400RV

Z-42.1-394

Low

inst

alla

tion

heig

ht

232 m

m



1All mouldings tested and approved by the DIBt Z-42.1-394 7

DN 110/110

The real all-rounder connecting sleeve Airfi t-Plus DN 110/110

• Fits all pipes from 99 mm interior Ø.• Particularly easy to install.• Eccentric design.

Item no. 111110S


Connecting sleeve DN 160/160 and DN 110/110

Typical problem in old buildings:a free-standing WC needs to be replaced, but the sleeve in the ground is missing. The Airfi t connecting sleeve is the ideal adapter for joining a drain pipe and WC pipe connection.

Typical problem in new buildings:the sleeves on pipes that jut out of the fl oor plate are often damaged or missing.

Item no. 110110S

Item no. 160160S

DN 110Spigot end

DN 110Muffe

99 -105mm


Item no. 112110WS

DN 100

Angle connecting sleeve • Space- and time-saving.

Item no. 91110WS

DN 90/110

Fire performance: tested according to DIN 4102-B2, EN 13501-1-E, EN 11925-2 99-105 (DN 110)

DN 9

0

DN 1

10

99-105 (DN 110)


DN 110/110

DN 160/160

DN 110

SML


Fire

per

form

ance

: te

sted

acc

ordi

ng to

DIN

410

2-B2

, EN

1350

1-1-

E, E

N 11

925-

2

Z-42.1-394 Z-42.1-394

Z-42.1-394

Z-42.1-394

Z-42.1-394



DN 110/110


Connecting sleeveDN 160/160DN 110/110


12 8

black

grey*

white

Cut a hole using a ø 76 mm circle cutter and screw the pipe stopper in.

2 3 54 6

ø 76 mm

... no cleaning aperture! 1) The pipe stopper • 2) Drill hole Ø 76 mm • 3) Deburr • 4) Fit edge profi le, clean • 5) Fit pipe stopper • 6) Tighten screw READY!

Dismantling: 6 turns to the left and push screw to the stop. Pull out pipe stopper.An edge profi le is supplied to protect the pipe wall when cleaning with a spiral.

Set

Item no. 20076KS

Black PE rain standpipe with pipe stopperØ 110 - length 1 m -

Black PE rain standpipe Ø 110 - length 1 m -

Item no. 4002PE

Item no. 4001PE

Item no. 4000S

Item no. 4000W

Item no. 4000G

The benefi ts of PE pipes:• UV- and weather-resistant • Frost-proof even when fi lled• Impact- and crack-resistant• Does not dent• Practically unbreakable

PE pipes EN 1519

Gal

van

ised

ste

el Ø

100

–110

mm

Bla

ck P

E Ø

110

mm

HT

Ø 1

10 m

m

SML

Ø 1

10 m

m

For pipes with an external diameter of 100 to 110 mm with a wall thickness of up to 6 mm.

The pipe stopperFor pipes with an external diameter of 100 to 110 mm with a wall thickness of up to 6 mm.

All metal parts are made of stainless steel.

Item no. 4000GFor retrofi tting to all drain pipes as a cleaning aper-ture; for indoor and outdoor use. Closes permanently; water- and gas-tight.The Airfi t pipe stopper is a must in any service vehicle!

1

Optimal internal adjustment.

Repairing drilled or damaged pipes

is no problem at all.


Accessories:Circle cutter Ø 76 mm

HSS bimetallic, complete, for plastic and metal. When working on metal pipes, use lower speed and cutting oil.

UV-stabilised

*The Airfi t pipe stopper is made of PP and exhibits normal fl ammability according to DIN 4102 B2

The pipe stopper is the perfect s

olution!


olution!


olution!


olution!


olution!


olution!


olution!


olution!


olution!


olution!


olution!


olution!


olution!


olution!


olution!


olution!


olution!


olution!


olution!


olution!


19

Made of PP

In the building

Every fi tter knows the problem! When installing conventional double sliding sleeves, it is hard to gain purchase to push it back and your grip is constantly slipping. Using a hammer or mallet dents the seal grooves. These crack and burst.

Hairline cracks appear and widen over time. The next leak test of the ground pipes involves signifi cant costs and extensive clean-up work.

A lot of planners and architects no longer accept conventional

sliding sleeves!

The solution: Airfi t Double Sliding Sleeve Plus.

sliding sleeves! sliding sleeves! sliding sleeves! sliding sleeves! sliding sleeves! sliding sleeves!

The problem with standard dou-ble sliding sleeves.

*Longer than required by EU standard


DN 110 DN 125 DN 160

For underground pipes DN 110 DN 125 DN 160

DN 110 DN 125 DN 160

+26 mm* +24 mm* +46 mm*

+18 mm* +14 mm* +28 mm*

+18 mm* +14 mm* +28 mm*

Item no. 30125HT Item no. 30160HTItem no. 30110HT

Item no.30125KGItem no. 30110KG Item no. 30160KG

Item no.31125KGItem no. 31110KG Item no. 31160KG


Thanks to the two solid stop collars, it is no problem to apply a crow-bar or a pipe and then the Airfi t Double Sliding Sleeve Plus can eas-ily be pushed onto the end of a pipe.

Benefi ts:• No more damaging seal grooves.• No more hairline cracks caused by impacts. • Permanently sealed.• Low risk of warranty claims.• Less consequential damage.• Less stress with planners, architects, authorities and developers.• Made from environmentally sound PP.• High resistance to impacts, even at low temperatures.

Problem solved.


PVC

PVC


12

DN 75/50 fl ange adapter

Item no. 7550FA

Hole spacing 100–105 mm

DN 50

Set

Stainless steel

10



DN 75

Airfi t Flange Adapter for retrofi tting on cast iron cleaners for discharging waste water from condensing boilers, wash basins, sinks, etc. Remove the screw cap from the cast iron cleaner and screw in the Airfi t Flange Adapter.

Hole spacing 125–143 mm

All fl ange adapters fi t the old black cast iron pipes. (CI pipes)


Hole spacing 125–143 mm DN 50DN 110

Set

Item no. 11050FA

Made of PP, fi re performance:

tested according to DIN 4102-B2, EN

13501-1-E, EN 11925-2

Made of PP, fi re performance:

tested according to DIN 4102-B2, EN

13501-1-E, EN 11925-2

GmbH & Co. KG • Gewerbegebiet Zingsheim-Süd 40 • D-53947 NettersheimTel.: +49 (0) 2486 80 28 19 • Fax.: +49 (0) 2486 80 27 37 • www.airfit.eu • [email protected]

4 0 4 8 7 9 7 1 1 9 1 1 2

Art. Nr. 119110FA

2x

1 2 3

4 5 6

Lochabstand 125 - 143 mm

Aus PP, Brandverhalten: Geprüft nach DIN 4102-B2, EN 13501-1-E, EN 11925-2, Wasserdicht: 3m WS

Flansch AdapterDN 110/110

DN 110/110

GmbH & Co. KG • Gewerbegebiet Zingsheim-Süd 40 • D-53947 NettersheimTel.: +49 (0) 2486 80 28 19 • Fax.: +49 (0) 2486 80 27 37 • www.airfit.eu • [email protected]

4 0 4 8 7 9 7 1 1 9 1 1 2

Art. Nr. 119110FA

2x

1 2 3

4 5 6

Lochabstand 125 - 143 mm

Aus PP, Brandverhalten: Geprüft nach DIN 4102-B2, EN 13501-1-E, EN 11925-2, Wasserdicht: 3m WS

Flansch AdapterDN 110/110

DN 110/110Set

Item no. 119110FA



1

Screw-in sleeve DN 50 – grey

Screw-in sleeve DN 50 – greenUV stabilised

Pipe connections for containers

DN 110DN 75 DN 125≥ DN 110

Screw-in sleeve DN 50made inGermanymade inGermany

The Airfi t Screw-in Sleeve DN 50 for subsequent connection of HT cleaners from DN 75 onwards for the discharge of waste water from condensing boilers, sinks, washing machines, etc.

Item no. 50001AM

Item no. 50000AM

Drilling depth 47 mm complete, for plastic.

Item no. 20059KS

Accessories: circle cutter Ø 59 mm

Item no. 21059KS


Made of PP, fi re performance: tested according to DIN 4102-B2, EN 13501-1-E, EN 11925-2


Item no. 20121KS

DN 110


Cut a hole using a circle cutter and screw in the screw-in sleeve. And that’s it!

Screw-in sleeve DN 110

Drilling depth 47 mm HSS bimetallic, complete, for plastic and metal. When working on metal pipes, use lower speed and cutting oil.

DN 110Item no. 50110AM

11

Ø121 Ø135

Drilling depth 47 mm HSS bimetallic, complete, for plastic and metal. When working on metal, use lower speed and cutting oil.

DN 50

DN50DN50

DN50

DN50

* Drill hole, deburr, insert screw-in sleeve, screw on cap nut.

**

**

*

The problem solvers!

DN 50

12

Optimal transition from hose to drain pipe.

ø 25 mm* ø 19 mm* ø 13 mm* ø 10 mm* ø 8 mm*

Item no. 50010SW

Item no. 50016SW

Item no. 50018SW

PP angle hose

Universal pump angle

Universal hose nipple

Universal pump nipple

Condensate set

Screw-in sleeve DN 50 grey

L 800mm

Item no. 50012KS

DN 50

DN 50


DN 32

Item no. 50011SN

Item no. 50014SK

Item no. 50015SN

Item no. 50017SN

Item no. 50019SN

Item no. 50013SN

PP hose nipple

DN 40

DN 40

DN 50

Optimal connection of different pipe sizes. Simply cut to size. Made of PP, hot water-resistant.

DN 50x19-21 mm

DN 40x25-8mm

1 1/4" AGx32-8 mm PVC

3/4" / 1" / 1 1/4" AGx32-8 mm PVC

3/4" AGx25-8 mm PVC

DN 32x25-8mm

DN 50x25–8 mm

DN 40x25–8 mm

Universal hose connector – double-ended ø 8–25 mm

ø 13 mm* ø 10mm* ø 8mm* ø 32 mm* ø 25 mm* ø 19 mm*

3/4" 1" 1 1/4"

1 1/4"

3/4" ø 25 mm* ø 19 mm* ø 13 mm* ø 10 mm* ø 8 mm*

Washing machines and dishwashers

ø 21 mm

ø 19 mm

ø 32 mm*

ø 25 mm*

ø 19 mm*

ø 13 mm*

ø 10mm*

ø 8 mm*

ø 25 mm*

ø 19 mm*

ø 13 mm*

ø 10mm*

ø 8 mm*

*Simply cut to size.

*


1

Item no. 50110AMItem no. 50011SNItem no. 50010SW

IBC TANK

DN

110

Pipes or bends

Item no. 50000AM

DN

50

Pipes or bends

Installation instructions:

Everyone knows the problem with a broken drain cock. Leaky, frost-damaged or jammed, etc.

Suitable for Schütz, Marmor and Mauser tanks with an aluminium cap nut.

Screw-in sleeve DN 110Screw-in sleeve DN 50 grey

Large brass ball cock 3/4" with hose connector

Brass thread insert

Item no. 50500TSTank adapter discharge setConsisting of:

Gasket, ball cock, adapter.

No more need for "DIY". Professional tank accessories from Airfi t.

13

DN 50

DN 50

1 2 3 4

128 mm

57mm3/4"

Tankadapter-Auslauf-Set

Art. Nr. 50500TS

3,0 mm

74mm 67mm3/4"

ø 67mmø 57mm

The outer diameter can be reduced by grinding

Additional seal to enlarge.

Item no. 50600TS

Item no. 50650TS

Item no. 50601TS

Item no. 50651TS

Item no. 50602TS

Item no. 50652TS

2" IG 59X6 IG

Item no. 50650TS

Tank valve

6 mm

3/4"

ø 59

Consisting of: Ball cock and cap nut

Tank adapter

Tank adapter tank thread 59 mm AG X 2" IG, yellow

Tank adapter tank thread 52 mm AG X 2" IG, green

Tank adapter tank thread 69 mm AG X 2" IG, brown

Tank valve, ball cock 3/4" with cap nut on tank valve AG 59x6 mm, blue

Tank valve, ball cock 3/4" with cap nut on tank valve AG 52x6 mm, blue

Tank valve, ball cock 3/4" with cap nut on tank valve AG 69x6 mm, black



12 14

The most easy-to-install funnel siphon of all time.

• Assembly time less than 30 seconds.• No drilling, wall plugs or screws.• No assembly required.• Low space requirement.• Supply from several pipes possible.• After removal of the inner part, the siphon is used as a

cleaning port.• No tools needed for installation.• Always tight, as it has no fi ttings with seals.• 4 possible pipe connections.• No fastening required.• Insert Airfi t FUNNEL SIPHON – You’reREADY TO GO!

Examples of use:

DN 125 DN 110

Sleeve DN 125

Sleeve DN 110

Spigot DN 110

Sleeve DN 50

DN 110 DN50

A must for every rooftop control system!

The funnel siphon has been tested according to DIN-EN 274 by MPA-NRW.


Item no. 50125TS

188

mm

50 m

m

Water trap height 50 mm



115

Spigot endDN 110 DN 110 DN 90

120 mm

99 -105 mm

150

mm 87

mm

DN 50

The “Professional” Insert! And that’s it!

The most versatile fl oor drain ever.


Fire

per

form

ance

: te

sted

acc

ord

ing

to

DIN

410

2-B

2,

EN 1

3501

-1-E

, EN

119

25-2

• Pulling out the siphon insert provides a cleaning aperture.

• Impact-resistant PP housing.

• Removable ribbed seal.

Stainless steel grate 3 mm1.4301 V2a K3

50 mm water trap heightaccording to DIN EN 1253

Spigot DN 110

Sleeve DN 110

Sleeve DN 90

Sleeve DN 50

Height adjustable, can be turned.

Stainless steel grate

No screw fi ttingItem no. 60200BA

ScrewedItem no. 60201BA

27mm


12

Universal adjustable bends with two pivots Benefi ts compared to three-piece adjustable bends• Universal bend, continuously adjustable from 0°–90°.• The degree scale is stamped on the bend.• The ideal angle always available.• Ideal for the after-sales service vehicle.• No more need for time-consuming journeys to fetch parts.

Benefi ts compared to bends with a swivel joint• No contraction in the cross-section.• Reduced risk of blockage.• Axial orientation retained at all angles.• You leave expert work with the customer.

30°

90°

45°

45°

90°

DN 40 grey

DN 50 grey

DN 75 grey

DN 110 grey

0°–90° continu-ously adjustable

Item no. 52040UR

Item no. 52050UR

Item no. 52075UR

Item no. 52110UR

DN40 white DN 50 white

Item no. 53040UR

Item no. 53050UR

DN 40 grey

DN 50 grey

DN 75 grey

DN 110 grey

Item no. 55040UA

Item no. 55050UA

Item no. 55075UA

Item no. 55110UA

End plug with screw cap (grey), for insertion in a sleeve.

DN 40

DN 50

DN 75

DN 110*

DN 125*

DN 160*

Item no. 51040ES

Item no. 51050ES

Item no. 51075ES

Item no. 51110ES

Item no. 51125ES

Item no. 51160ESUse as a cleaning aperture.

16


*

DN 50

Item no. 28155AV

DN 110x50x50DN 50

Item no. 28150AV

DN 110x50

Item no. 28050AVMade of PP according to EN 1451 B

DN 50

HT branch continuously adjustable 45°–88°

45°–90° continu-ously adjustable


1

The discharge and connection hose is a real problem solver for fast and fl exible connection of: • Shower baths• Bath tubs • Sinks, etc.

The connection hose offers the following benefi ts:• Almost totally smooth interior.• Not susceptible to blockages.• Pressure resistant to 0.5 bar.• Heat-resistant: up to 100°C (short-term).• Made of liquor- and heat-resistant plastic.• Sleeve connection DN 50.• Spigot DN 50 – DN 40• Solid and stable design.

HT connection hose DN 50 fl exible

Length 750 mm

Length 250 mm

Length 1000 mm

ø 5

0

ø 5

0

ø 4

0

ø 4

0

ø 5

0

ø 5

0

ø 3

2

ø 4

0

ø 3

2

Length: 250 mm - 500 mm - 750 mm - 1000 mm Colour: grey

Item no. 50225AS

Item no. 50750AS

Item no. 50500AS

DN 98 – DN 105285–500 mm extendible.Top quality.

PP pipe vent for drain pipes

WC connection pipefl exible, white

Item no. 90010WA

Item no. 57050RB

grey, DN 50DIN EN 1451B

Item no. 85040SK

DIN EN 4102B2

Item no. 57075RB

grey, DN 75DIN EN 1451B

Item no. 57110RB

grey, DN 110DIN EN 1451BUniversal coupling

DN 98 – DN 105

PVC-U reducer DN 110x40x40For insertion in PP sleeves or for bonding in PVC-U sleeves.

Ultra-short reducer DN 110x90 made of PP

Ultra-short reducer DN 50x40 made of PP Item no. 11044KR

PVC-U

PVC-UDN 110

PPDN 110 made in

Germanymade inGermany

Item no. 51000AS

Length 500 mm

Item no. 56540KR

Item no. 56532KR

Item no. 56432KR

DN 50/40

DN 50/32

DN 40/32

ø 5

0

ø 5

0

ø 4

0

ø 4

0

ø 5

0

ø 5

0

ø 3

2

ø 4

0

ø 3

2

DN 40/32 DN 50/32 DN 50/40

Short reducer

17

2.00 mm

1.80 mm

Item no. 81109SK

DIN EN 4102B2

Installation height

Installation height





12

Seal for urinal intake

Urinal intake fi ttings for UP 1/2" with seal

Item no. 90004UZ

Urinal intake fi ttings for UP 1/2" with seal10 mm offset!

Item no. 90003UZ

10 mm

The problem:The connection size between the intake and the outfl ow doesn’t match.

The solution:Airfi t offset intake fi ttings.

Item no. 90001UZ

Urinal intake fi ttings for UP 1/2" with sealNo offset!

5 mm

Item no. 90002UZ

Urinal intake fi ttings for UP 1/2" with seal5 mm offset!

18



1The repair case is a must in any service vehicle!

Stainless steel hose clamps 12 mm W4

Item no. 45000RS

Airfi t Repair Plug!

DN 40DN 50DN 75DN 90DN 110DN 125

Everyone knows the problemwith pierced drain pipes in the wall. The solution: Airfi t Repair Plugs!

Repair plugs for reordering. with stainless steel hose clamps and seal

The repair plugs are suitable for permanent sealing of pierced drain pipes. For pipe materials. Fix the plug in place with the clamp and tighten carefully.

19



DN 40 Item no. 45040RS DN 50 Item no. 45050RS DN 75 Item no. 45075RS DN 90 Item no. 45090RS DN 110 Item no. 45110RS DN 125 Item no. 45125RS


12 20

Item no. 50400TR

Telescopic pipe DN 50, variable length ~ 250 to 400 mm.The solution e.g. for connecting shower baths and the subsequent installation of branches.

Signifi cant time savings and ease of use.

~ 250 mm

~ 400 mm~ 150 mm

Item no. 20600SZ

Airfi t screw clamp

... for simple unrolling or diversion of underfl oor heating pipes,

cables and hoses, etc.

Simply fi t the screw clamp in the doorway or ceiling cavity. Lay the underfl oor heating pipe or cable and easily pull tight.

• Signifi cant energy and time savings.• Temporarily replaces a whole worker.• Easy to use.



1

S-connectionassembly tool 3/4" with 1/2" ratchet socket, Hex shankor with hanger bolt wrench

Item no. 20514EEItem no. 20504AE Item no. 20500HFItem no. 20714WC

185

mm

Item no. 20510ASSW 10

SW 10


SW 11


SW 12


SW 13

Item no. 20509ASSW 9 Item no. 20503EE

Sanitary fittings case “Professional”

➊➋➌➍ Stand fitting spanner, extra long, 185mm

➎ Spanner for fitting WC seat➏ Fitting tool for drain valves➐ Hanger bolt wrench M8/M10➑ Angle valve fitting aid➒ S-connection assembly tool ➓ Tap extension miller SDS uptake 1/2"

... for 1/2" ratchet

5

5

1

1

1

7

3

3

3

6

6

2

2

2

8

8 8

11

10

10

4

4

4

9

9

7

Item no. 20501SD Item no. 20100SA

Item no. 20502SA

made inGermany

With 12 hardened steel rollers!

• The ideal too for screwing in and out and also aligning S-angles.• Small and compact design. • With 12 hardened steel rollers for optimum distribution of force.• Low weight. • A must in every tool kit!

• Insert the hanger bolt in the socket• Trouble-free turning to the left and right• Pull off the socket

Benefits:- No need to screw in the hanger bolts.- Thanks to the hardened rollers, the threads are preserved and not damaged.- When unscrewing, the hanger bolt cannot fall out of the tool.

Hanger bolt driver for screwing and unscrewing hanger bolts.

SDS shank

Hex shank

M10

M8

JUST INSERT - NO NEED TO SCREW!

Usage example with a hanger bolt wrench:

Item no. 20206SS

Item no. 20212SS

Item no. 20210SS

Item no. 20208SS

M 6 - hex shank

M 8 - hex shank

M 10 - hex shank

M 12 - hex shank

M 6 - SDS shank

M 8 - SDS shank

M 10 - SDS shank

M 12 - SDS shank

Item no. 20306SS

Item no. 20312SS

Item no. 20310SS

Item no. 20308SS

Item no. 20400SK

97

11

11

9

The original!

21


12

• Always reusable.• External diameter of just Ø=33 mm.• Corresponds to approx. 77% less surface than plastic plugs.• Approx. 11 mm smaller diameter that plastic plugs.• Solid brass.• Corresponds to DIN EN 1717.• The small Airfi t brass building plug can remain permanently installed.• Stress with building owners and tilers because of excessively large holes in tiles is a thing of the past.

The solution: The Airfi t brass building plug, small

Stress with building owners and tilers is practically guaranteed!

The Building plug valve, the water supply solution

for all builders!• Bleeding. • Connectivity between hot and cold water (leak testing).• Flushing connection.• Connection for leak testing.• Water extraction possible at any time.

• The Airfi t building plug valve can be easily tiled over without disassembly.

• Simple test fi lling of bathtub and shower/bath to test the outfl ow for leakages.

The Airfi t building plug valve is a must on any construction site.

33 mm31mm 1/2“

M 1:1

Herkömmlich ≈ Ø 44≈ 1.450 mm2

Baustopfen-Small Ø 33855 mm2

M 1:1

REPLACEMENT HOSE CONNECTOR

Ø 33 mm

M 1:1

The problem:



1/2"

Item no. 12000BS

Item no. 15800BV

Item no. 15805SV

Conical design

22

Valve with “super-glued” joint connector.

Easy disassembly, as there are no disturbing RIBS!

Airfi t Brass Building Plugs, small

Small Brass Building Plugs ø33

CONVENTIONEL =/ 44mm


123

FrontRear

• EU quality.• DVGW and KTW approval.• Sturdy PP case fi lled on both sides.• Minimum thickness of the seals: 2 mm.• Around 800 seals that really make sense.

Item no. 70000DK

Airfit GmbH & Co.KGGewerbegebiet Zingsheim-Süd 40D-53947 Nettersheim • Tel.: +49 (0)2486-802819Fax: +49 (0)02486-802737 • www.airfit.eu

Universal O-ring assortment• Tested to DIN ISO 3601-1

• Metric

• 419 pieces• Oil resistant

• NBR Material

• 32 different sizes

Number item ID SDR-01R-02R-03R-04R-05R-06R-07R-08R-09R-10R-11R-12R-13R-14R-15R-16

Number item ID SDR-17R-18R-19R-20R-21R-22R-23R-24R-25R-26R-27R-28R-29R-30R-31R-32

Of course, proven quality!

20202020202020161616151212121010 10

101010101010101010101010101010 22,40

23,6025,0026,5028,0030,0031,5032,5034,5035,5037,5040,0042,5045,0047,0050,00

3,15 4,00 5,00 6,00 7,10 8,0010,0010,0011,2011,8014,0016,0017,0019,0019,0020,00

1,80

2,65

3,553,55

3,553,553,553,553,553,553,553,553,553,553,553,553,553,553,553,55

1,801,801,801,801,801,80

2,652,652,652,652,652,65

• resistance to water up to 100°C

Cat. no. 70001DK

4 048797 700013

Universal seal case for gas water heating fi lled with everything you could ever really need.

Item no. 70001DK


EU quality • DVGW and KTW approval •

Minimum thickness of the seals: 2 mm • 234 seals •

Item no. 70002DK

Universal seal assortment for sanitary heating

Filled with everything you could ever really need.


GmbH & Co. KG Gewerbegebiet Zingsheim-Süd 40 D-53947 Nettersheim - Germany Tel.: +49 (0) 2486 80 28 19 Fax.: +49 (0) 2486 80 27 37 www.airfi t.eu • post@airfi t.eu

• Simple maintenance.• Simple and problem-free installation in new and old buildings.• The lid protector and all fasteners and screws, nuts, washers

are made of stainless steel.• For sewage-free waster water.• Flap closes automatically with an additional manually control-

lable emergency closure.• Backfl ow protection and vermin protection.

Backfl ow valve with additional manual closure EN 13564

A Zimmermann Group company

Grap

hics

& p

hoto

grap

hy ©

4Co

uleu

rs.d

e

DN 50

DN 50

DN 50

DN 50

Item no. 50110RKDN 110




Item no. 59110DRK

DN 110

Item no. 59160DRKDN 160

Double backfl ow valve

For drainage pipes For underground waste pipes

Item no. 33110REKDN 110



Pipe end cap

for preventing backfl ows and vermin.

Subj

ect t

o ch

ange

. Oth

er p

rodu

cts i

n pr

epar

atio

n. Ill

ustra

tions

may

di�

er fr

om th

e or

igin

al.

Backfl ow valve for vertical fi ttingThis backfl ow valve for installation in vertical drain pipes is the most convenient solution and often the only option for protecting buildings from fl ooding.

Item no. 58110RKSDN 110

DN 50

Item no. 50050GRK

Item no. 50051WRKWhite

Grey

DN 50 = 180 mm DN 110 = 287 mm DN 125 = 318 mm DN 160 = 367 mm DN 200 = 480 mm

TOTAL INSTALLATION LENGTH

Automatic closure of the valve in case of backfl ow.

<

287m

m

>

Backfl ow valve vertical

DN 50Item no. 58050RKS

close

open

DN 50

DN 110

normal fl owLever in the OPEN position

lockingLever in the OPEN position

blocking normalLever to the CLOSED position

Operating temperatureMaximum: 95 ° C

DN 110x90 - AIRFIT · DN 110x90 DN 125x90 DN 160x90 ... tested according to DIN 4102-B2, EN...

Documents

Transcript of DN 110x90 - AIRFIT · DN 110x90 DN 125x90 DN 160x90 ... tested according to DIN 4102-B2, EN...