DIN Standard for Mining.pdf

7/23/2019 DIN Standard for Mining.pdf

1/45

Register of Mining Standards

FABERG Normenausschuss Bergbauim DIN Deutsches Institut fr Normung e.V.

Published by

2010-12dated

Contact Hans Georg Blasgude [email protected]

Page 1 of 45FABERG Normenausschuss Bergbau


2/45

Normenausschuss Bergbau (FABERG) is an agency of DIN Deutsches Institut fr Normung e.V., Berlin. As a jointestablishment of the German mining industry, it is supported by Vereinigung Rohstoffe und Bergbau e.V., Berlin and managedby a governing body. From a management and staff point of view, it is associated with DMT DeutscheMontanTechnologie frRohstoff, Energie, Umwelt e.V. of Essen.FABERG is responsible for national standardisation in the field of mining and acts as a representative for this field in European(CEN) *) and international (ISO) **) standardisation efforts, supporting the introduction of standards in its specialised field forany practice affected by these and is instrumental in establishing the German standards system.An association representing the interests of the mining industry was formed as early as at the end of the 1800s as a joint

effort of mines in the German Ruhr area also dealing with issues of standardisation and recommending to its membercompanies the use of specific pipes and underground rail systems.After World War I, a committee was formed, dealing with standardisation on behalf of the coal mining industry in the GermanRhineland and Westphalia. It was realised at an early date that standardisation involving the entire mining industry would bemore effective and useful. This lead to the foundation of Fachnormenausschuss fr den Bergbau (FaBerg) on November 28th,1922 at Hannover.Whereas during the first years of FABERGs existence, dimensional and type standards were primarily set up, these wereincreasingly followed by quality and demand-based standards. Personal safety equipment, too, was subject to standardisationat an early date.In 1955, during the ISO General Assembly at Stockholm, the foundation of a Mining technical committee - ISO/TC 82 wasresolved, management of which was transferred to FABERG. In addition to this, FABERG is responsible for Germanrepresentation in ISO/TC 27 "Solid Mineral Fuels".Within the scope of its CEN work delegated by the EU, FABERG was allocated the CEN/TC 196/WG 3 "Hydraulically PoweredSupport and CEN/TC 305/WG 5 "Equipment and Protective Systems for Mining" Secretariat.FABERG co-operates with other standards committees of DIN, CEN and ISO at national, European and international level, inorder to represent the interests of the mining industry.

The Register of Standards comprises ISO standards of TC 27 "Solid Mineral Fuels" and of TC 82 "Mining". The register also includes Operating Recommendations for Mining (Bergbau-Betriebsbltter). These are recommendations setup by professionals, based on the same principles, which are mandatory for wording DIN standards. Users of theserecommendations are subject to examining whether any arrangements recommended in these are adequate. Bergbau-Betriebsbltter are published by DMT DeutscheMontanTechnologie fr Rohstoff, Energie, Umwelt e.V. Bergbau-Betriebsblttermay be ordered from DMT DeutscheMontanTechnologie fr Rohstoff, Energie, Umwelt e.V., FABERG, NormenausschussBergbau, Am Technologiepark 1, 45307 Essen, Tel: (0201) 172-1553.

The Standards Inspection Office of DIN in FABERG is available for inspection of any national DIN standards. Research workmay be conveniently performed through the Perinorm database of BSI, AFNOR and DIN and ISO/IEC, CEN/CENELECstandards.

Opening times of Standards Inspection Office (Normenauslegestelle):Monday to Friday: 8.00 a.m. to 11.30 a.m. and 1.00 p.m. to 2.30 p.m.---------*) CEN = Comit Europen de Normalisation**) ISO = International Organization for Standardization

Foreword



3/45

The number s af t er t he t i t l es of DI N st andar ds and DI N dr af t s i n br acket s ar e pr i cegr oups ( dat ed 2009- 01- 01) ; t hey corr espond wi t h t he f ol l owi ng pr i ces:Prei sgr . EUR Prei sgr . EUR Prei sgr . EUR

01 14, 70 19 114, 00 37 280, 6002 21, 50 20 119, 00 38 304, 3003 21, 50 21 124, 50 41 323, 9004 21, 50 22 129, 10 42 343, 2005 30, 60 23 134, 0006 37, 10 24 139, 6007 43, 40 25 144, 1008 49, 90 26 149, 1009 56, 10 27 154, 6010 62, 20 28 159, 7011 68, 60 29 164, 6012 75, 10 30 169, 5013 81, 10 31 174, 2014 87, 40 32 190, 8015 93, 80 33 204, 1016 99, 10 34 220, 8017 104, 00 35 232, 8018 108, 80 36 256, 80

Fur t her i nf ormati on on pr i ces you wi l l get by DI N Deut sches I nst i t ut f r Normung e. V.i n Ber l i n.

The number s af t er t he t i t l es of " Ber gbau- Bet r i ebsbl t t er " i n br acket s ar e pr i ce gr oups( dated 2009- 01- 01) ; t hey corr espond wi t h t he f ol l owi ng pr i ces:Gr oup EUR

1 7, 702 10, 503 13, 104 15, 705 21, 60



4/45

FB Shaft 01Register of Mining Standards 2010-12

01 Shaft

NA 008-01-01-01 AK Shaft s ink ing devices

DIN 21151 11.09 Shaft sinking; pulleys for flat winding ropes; safety requirements and testing (8)DIN 21164 05.03 Shaft sinking - Riders for winding kibbles - Safety requirements and testing (12)DIN 21181-1 03.10 Shaft sinking Debris kibbles - Part 1: Debris kibbles with suspension hanger (12)DIN 21181-2 03.10 Shaft sinking; debris kibbles - Part 2: Debris kibbles with suspension two-strand

chain set (9)DIN 21186 04.94 Shaft sinking; rope suspension gears for load hoisting in shafts; safety

requirements and testing (6)DIN 21187 04.94 Shaft sinking; chain suspension gears for load hoisting in shafts; safety

requirements and testing (5)DIN 21194 12.99 Shaft sinking - Abutment for guide ropes - Safety requirements and testing (7)DIN 21198 11.09 Shaft sinking - Shaft plumbs (6)

NA 008-01-01-02 AK Freezing shaft const ruc tion

DIN 4930 06.89 Pipes for use in freezing shaft sinking; dimensions and technical deliveryconditions (5)

NA 008-01-01-03 AK Shaft support

DIN 21500 11.01 Shaft sinking in mining - Design and dimensioning (12)

NA 008-01-02-01 AK Hoist ropes

DIN 4118 06.81 Head frames and winding towers for mines; Design loads, calculation principlesand design principles (4) /FABERG co-author/

DIN EN 12385-1 01.09 Steel wire ropes - Safety - Part 1: General requirements; German version EN12385-1:2002+A1:2008 (12) /FABERG co-author/

DIN EN 12385-2 06.08 Steel wire ropes - Safety - Part 2: Definitions, designation and classification;German Version prEN 12385-2:2002/+A1:2008 (20) /FABERG co-author/

DIN 12385-2/B1 01.09 Steel wire ropes - Safety - Part 2: Definitions, designation and classification;German Version prEN 12385-2:2002/+A1:2008, Corrigendum to DIN EN12385.2:2008-06 /FABERG co-author/

DIN EN 12385-3 06.08 Steel wire ropes - Safety - Part 3: Information for use and maintenance;German version EN 12385-3:2004/+A1:2008 (13) /FABERG co-author/

DIN 12385-3/B1 01.09 Steel wire ropes - Safety - Part 3: Information for use and maintenance;German version EN 12385-3:2004/+A1:2008, Corrigendem to DIN EN12385.3:2008-06 /FABERG co-author/

DIN EN 12385-6 05.04 Steel wire ropes - Safety - Part 6: Stranded ropes for mine shafts; Germanversion EN 12385- 6:2004 (12)

DIN EN 12385-7 02.03 Steel wire ropes - Safety - Part 7: Locked coil ropes for mine shafts; Germanversion EN 12835-7:2002 (9)

DIN 21258 10.07 Lubricants and impregnating compounds for friction hoist ropes in mining -Safety requirements and testing (9)

NA 008-01-02-02 AK Hanging gears

DIN 21341 08.86 Wooden mine guides (6)DIN 21346 11.89 Square head bolts for shaft guides (5)DIN 21371 01.88 Rope attachments; assemblies (5)

DIN 21376-1 07.88 Guide shoes for shaft conveyances and counterweights with guide rollers inmining (5)



5/45

FB Shaft 01Register of Mining Standards 2010-12

DIN 21376-2 07.88 Guide shoes for shaft conveyances and counterweights with slide-ways inmining (5)

DIN 21377 12.94 Steel railings for shaft conveyances in mining (5)DIN 21381 01.88 Rope attachments; thimble connection plates for round ropes (5)DIN 21382 01.88 Rope attachments; outer plates, inner plates (5)DIN 21383 01.88 Rope attachments; pins (5)

DIN 21386 01.88 Rope attachments; thimbles for round ropes (5)DIN 21388 01.88 Rope attachments; universal joints (5)DIN 21389 01.88 Rope attachments; clamp thimbles (5)DIN 21390 02.85 Thimbles for flat ropes (5)

NA 008-01-02-03 AK Braking calcul ations

DIN 20400 01.90 Knuckle threads for the mining; threads with large load-bearing depth (6)DIN 22400 04.90 Control units of winding engines; hoists and winches for mining (5)DIN 22405 05.90 Friction pulley linings for winches and winders in mining (5)DIN 22406 10.86 Low speed Koepe winding machines with friction wheel, for shafts and drifts;

braking system calculation formulae (13)DIN 22410 05.94 Winding rope pulleys for round ropes (10)



6/45

FB Mine Support 02Register of Mining Standards 2010-12

02 Mine Suppor t

NA 008-02-01 AA Strut support

DIN 21315 03.89 Round pit timber; load bearing capacity of props and bars; calculation (5)DIN 21316 06.87 Round pit timber; props, bars (5)DIN 21317 06.87 Round pit timber; timber for lagging (5)DIN 21318 02.89 Round pit timber; pillar, supports (5)DIN 21320 06.87 Round pit timber; technical quality and delivery requirements (6)DIN 21321 06.87 Cut pit timber; square timber (5)DIN 21324 06.87 Cut pit timber; wood for cogs (5)DIN 21328 06.87 Cut pit timber; slabs (5)DIN 21546 08.90 Mine support; strut support; marking (3)DIN 21549 03.88 Mine supports; powered walking supports; terminology (5)DIN 21550 05.88 Mine support; roof bars for single props; testing, requirements (5)

DIN 21551 01.86 Mine support; roof bars single props; lengths (5)DIN 21555 08.91 Mine support; graphical symbols for the open loop control of powered support (6DIN 21556 02.87 Mine support; valves for individual props; identification code (5)DIN 21557 02.87 Mine support; yield valves for powered support; identification code (5)DIN 21561 09.86 Mine support; head for single props; connecting dimensions (5)

NA 008-02-02 AA Hydraulic powered roof support

DIN EN 1804-1 05.10 Machines for underground mines - Safety requirements for hydraulic poweredroof supports - Part 1: Support units and general requirements; English versionEN 1804-1:2001+A1:2010 (16)

DIN EN 1804-2 05.10 Machines for underground mines - Safety requirements for hydraulic poweredroof supports - Part 2: Power set and rams; German version EN 1804-2:2001+A1:2010 (16)

DIN EN 1804-3 05.10 Machines for underground mines - Safety requirements for hydraulic roof supports - Part 3: Hydraulic control systems; German version EN 1804-3:2006+A1:2010 (15)

NA 008-02-03 AA Roadway support

DIN 21319 02.89 Round pit timber; bolts (5)DIN 21326 04.89 Sawn pit timber; boards and planks (5)DIN 21327 02.89 Sawn pit timber; boards, planks and square-sawn timber for working platforms

(5)DIN 21329 06.87 Cut pit timber; technical terms of delivery and quality (5)BB 21510 06.95 Verzugsmatten - Technische Anforderungen (2)EDIN 21530-1 05.03 Mine support - Part 1: General (5)DIN 21530-2 05.03 Mine support - Part 2: Dimensions, designation and statical values (21)DIN 21530-3 05.03 Mine support - Part 3: Requirements (10)DIN 21530-4 05.03 Mine support - Part 4: Testing (10)DIN 21530-5 05.03 Mine support - Part 5: Marking of parts of mine support (6)DIN 21531-1 07.90 Arch supports; arches B 5, 4 to B 20, 2 (5)

DIN 21531-2 07.90 Arch supports; arches B 21, 7 to B 63 (5)DIN 21548 01.89 Rails for mine supports (5)



7/45

FB Mine Support 02Register of Mining Standards 2010-12

NA 008-02-03-01 AK Bol ts f or mine support

DIN 21521-1 07.90 Rock bolts for mining and tunnelling; terms (6)DIN 21521-2 02.93 Rock bolts for mining and tunnel support; general specifications for steel-bolts;

tests, testing methods (7)DIN 21522 07.72 Roof bolt plates for mining and tunnel support (4)



8/45

FB Extraction 03Register of Mining Standards 2010-12

03 Extraction

NA 008-03-01 AA Ext racting and st owing

DIN EN 1552 09.03 Underground mining machines - Mobile extracting machines at the face - Safetyrequirements for shearer loaders and plough systems; German version EN1552:2003 (10) /FABERG co-author/

DIN 20012 04.89 Pneumatic stowing pipes (5)DIN 20013 04.89 Sealings for pneumatic stowing pipes (5)DIN 20097 07.68 Gears for coal ploughs and underground chain- conveyors; signs for gears (4)

/FABERG co-author/DIN 20350 03.75 Protective clothing - General requirements; German version prEN 340:2000 (4)

/FABERG co-author/



9/45

FB Tools 04Register of Mining Standards 2010-12

04 Tools

NA 008-04-01 AA Hand tools/Rock dr illi ng

DIN EN 815 12.09 Safety of unshielded tunnel boring machines and rodles shaft boring machinesfor rock - Safety requirements; German version EN 815:1996+A2:2008 (16)/FABERG co-author/

DIN 1197-1 06.90 Eyes for picks, oval; dimensions, requirements, testing (5)DIN 1197-2 06.90 Pick eyes, oval; plug gauges (5)DIN 6436 06.90 Pickaxes (5)DIN 6437-1 06.90 Pickaxe handles; dimensions, requirements, testing (5)DIN 6437-2 06.90 Pickaxe handles; gauges (5)DIN 20109 06.90 Pickaxes, chisel and point ends (5)DIN 20110 06.90 Beater-pickaxes (5)DIN 20112 06.90 In triangular hand hoes (5)DIN 20115 06.90 Miners axes (5)

DIN 20119 07.90 Trough shovel (5)DIN 20120 07.90 Sand shovel (5)DIN 20121 07.90 Digging shovel (5)DIN 20123 07.90 Rimmed shovel (5)DIN 20124 07.90 Pan shovel (5)DIN 20125 07.90 Loading shovel (5)DIN 20127 06.73 Spades (4) /FABERG co-author/DIN 20128 07.90 Shallow rimmed shovel (5)DIN 20129 07.90 Plain shovel (5)

DIN 20135 07.90 Sledge hammer (5)DIN 20136 07.90 Hand hammer (5)DIN 20142 07.92 Hacksaws with steel frames and two handles (5)DIN 20151 01.84 Gears for coal ploughs and underground chain- conveyors; signs for gears (4)

/FABERG co-author/DIN 20152 03.89 Shovel and spade handels; types, dimensions, requirements, testing, marking

(5) /FABERG co-author/DIN 20301 01.99 Rock drilling operations - Terminology, units, and symbols for use in formulae (9DIN 20302 02.74 Rock drilling operations - Terminology, units, and symbols for use in formulae

(8) /FABERG co-author/

DIN 20311 11.02 Drill tubes with diameters exceeding 100 mm for large hole boring in mining (5)DIN 20314 06.90 Screw threads for drill tubes will diameters exceeding 100 mm for large hole

boring in mining (5)DIN 20361 04.10 Rock drilling - Chuck bushings - Connecting dimensions, material, design (4)DIN 20367 04.10 Rock drilling - Round screw connections for rotary drilling equipment -

Dimensions, design (5)DIN 20369 09.89 Pick hammers; flat- and shearpick without and with shank (5)DIN 20371 09.69 Hammer drilling; connecting tap for hammer drilling support (4) /FABERG co-

author/DIN 20372 05.88 Rock drilling; water tube; connecting dimensions, material, finish (5)DIN 20374 01.88 Pick hammers; gauges for picks (5)DIN 20375 01.88 Pick hammers; round picks without shank (5)DIN 20376 01.88 Pick hammers; round picks with shank (5)



10/45

FB Tools 04Register of Mining Standards 2010-12

DIN 20377 11.09 Rock drilling - Flush drills - Drill rod profiles, shanks and tapers (7)DIN 20378 10.90 Drilling hammers; taper gauges for tapered connections of drill rods and bits (5)DIN 20379 03.90 Drill bits with tapered connection for percussive wet rock drilling (5)DIN 20379-1 02.10 Rock drilling - Part 1: Tapered bits for percussive flush drillingEDIN 20379-2 02.10 Rock drilling - Part 2: Bits with internal thread for percussive flush drllingEDIN 24063 01.80 Operating elements (control devices) for pneumatic tools; terms, safety

requirements (4) /FABERG co-author/DIN 68340 01.89 Timber handles for impact tools; technical specifications (5) /FABERG co-author



11/45

FB Transport 05Register of Mining Standards 2010-12

05 Transpor t

NA 008-05-01 AA Mine railways

DIN 5902 11.95 Fishplates for grooveless flat bottom rails dimensions - Steel types (10)/FABERG co-author/

DIN 5904 11.95 Steel sleepers - Dimensions, static values, steel types (6) /FABERG co-author/DIN 5906 11.95 Short clips for grooveless flat bottom rails - Dimensions, steel types (6)

/FABERG co-author/DIN 5914 03.65 baseplate scrwes with rectangular head (4) /FABERG co-author/DIN 20449 10.88 Points and crossovers for rail haulage roads in mines; standard types,

terminology (7)DIN 20450 10.88 Simple underground track points; 20 m radius, 1 : 5 inclination; geometric

dimensions (5)DIN 20452-1 10.88 Simple points for underground tracks with loose heel switch; 20 m radius, 1 : 5

inclination, 600 mm gauge; compilation (5)DIN 20452-2 10.88 Simple points for underground tracks with spring switch blade; 20 m radius, 1 : 5

inclination, 600 mm gauge; compilation (5)DIN 20453-1 10.88 Switches for simple underground track points with loose heel switch; 20 m

radius, 1 : 5 inclination, 600 mm gauge (5)DIN 20453-2 10.88 Switches for simple underground track points with spring switch blade; 20 m

radius, 1 : 5 inclination, 600 mm gauge (5)DIN 20454 10.88 Crossings for simple underground track points; 20 m radius, 1 : 5 inclination,

600 mm gauge (5)DIN 20455 10.88 Check rail device for simple underground track points; 20 m radius, 1 : 5

inclination, 600 mm gauge (5)DIN 20458 10.88 Simple crossovers for underground tracks; 20 m radius, 1 : 5 inclination;

geometric dimensions (5)

DIN 20460 10.88 Simple underground track points; 30 m radius, 1 : 6 inclination; geometricdimensions (5)

DIN 20462-1 10.88 Simple points for underground tracks with loose heel switch; 30 m radius, 1 : 6inclination, 600 mm gauge; compilation (5)

DIN 20462-2 10.88 Simple points for underground tracks with spring switch blade; 30 m radius, 1 : 6inclination, 600 mm gauge; compilation (5)

DIN 20463-1 10.88 Switches for simple underground track points with loose heel switch; 30 mradius, 1 : 6 inclination, 600 mm gauge (5)

DIN 20463-2 10.88 Switches for simple underground track points with spring switch blade; 30 mradius, 1 : 6 inclination, 600 mm gauge (5)

DIN 20464 10.88 Crossings for simple underground track points; 30 m radius, 1 : 6 inclination,600 mm gauge (5)DIN 20465 10.88 Check rail device for simple underground track points; 30 m radius, 1 : 6

inclination, 600 mm gauge (5)DIN 20468 10.88 Simple crossovers for underground tracks; 30 m radius, 1 : 6 inclination;

geometric dimensions (5)DIN 20470 10.88 Simple underground track points; 50 m radius, 1 : 7 inclination; geometric

dimensions (5)DIN 20472-1 10.88 Simple points for underground tracks with loose heel switch; 50 m radius, 1 : 7

inclination, 600 mm gauge; compilation (5)DIN 20472-2 10.88 Simple points for underground tracks with spring switch blade; 50 m radius, 1 : 7

inclination, 600 mm gauge; compilation (5)DIN 20473-1 10.88 Switches for simple underground track points with loose heel switch; 50 m

radius, 1 : 7 inclination, 600 mm gauge (5)



12/45


DIN 20473-2 10.88 Switches for simple underground track points with spring switch blade; 50 mradius, 1 : 7 inclination, 600 mm gauge (5)

DIN 20474 10.88 Crossings for simple underground track points; 50 m radius, 1 : 7 inclination,600 mm gauge (5)

DIN 20475 10.88 Check rail device for simple underground track points; 50 m radius, 1 : 7inclination, 600 mm gauge (5)

DIN 20478 10.88 Simple crossovers for underground tracks; 50 m radius, 1 : 7 inclination;geometric dimensions (5)

DIN 20499 01.07 Rail haulage roads in mines - General rules (12)DIN 20500 10.88 Underground mine railways; track gauges and rails; standard types and

selection (5)DIN 20501 07.88 Pit railways; rails S 30, butt strap Fl 30 (5)DIN 20506 07.90 Clamping plates for securing rails onto steel supports (5)DIN 20536 01.92 Simple track points with spring switch blade; 120 m radius, 1:9 inclination, 900

mm gauge; compilation (6)DIN 20537 03.92 Switches for simple track points; 120 m radius, 1:9 inclination, 900 mm gauge

(6)

DIN 20539 03.92 Check rail device for simple track points; 120 m radius, 1:9 inclination, 900 mmgauge (5)

DIN 20548 07.90 Wheel sets for rail vehicles used in mines; rules for measuring (5)DIN 20549 11.86 Track gauges for pit railways; definition and tolerances (5)DIN 20550 07.90 Mine cars size small; components, main dimensions, design (5)DIN 20551 07.90 Mine cars - front wall, casing, frame, buffer sheet (5)DIN 20551 08.10 Mine cars - front wall, casing, frame, buffer sheet (10)EDIN 20552 11.88 Small size lubs; bumpers, supporting beam (5)DIN 20553 07.89 Wheel sets with taper roller bearings for mine cars; without springs (7)

DIN 20553 08.10 Wheel sets with taper roller bearings for mine cars; without springs (8)EDIN 20555 07.89 Wheel sets with taper roller bearings for mine cars; exterior spring suspension

(7)DIN 20555 08.10 Wheel sets with taper roller bearings for mine cars; exterior spring suspension

(11)E

DIN 20556 07.89 Wheel sets with taper roller bearings for mine cars; interior spring suspension (7DIN 20556 08.10 Wheel sets with taper roller bearings for mine cars; interior spring suspension (9EDIN 20560 07.89 Mine cars; middle size; dimensions, design and construction (5)DIN 20570 04.89 Mine cars; large size; dimensions, design and construction (5)DIN 20575-1 10.03 Rail transport - Passenger cars for underground mining - Part 1: Requirements

(6)DIN 20579-1 07.86 Buffer springs for mine cars; calculation (5)DIN 20579-2 07.86 Buffer springs for mine cars; requirements (5)DIN 20581 03.88 Mine cars; strap type coupling (5)DIN 20583 11.95 Mine cars - Shackle coupling (5)DIN 20586 05.91 Rail fastenings in mining for S 30 and S 33 rails on wooden sleepers (7)DIN 20586 08.10 Rail fastenings in mining for S 30E1 and 33E1 rails on wooden sleepers (8)EDIN 20600 01.07 Mine railways - Wheel profils for locomotives and cars (5)DIN 20601 05.91 Mine cars; tyres for mine locomotives (5)

DIN 21325 02.89 Pit converted timber; timber sleepers (5)DIN 21325 08.10 Pit converted timber; timber sleepers (5)E



13/45


DIN 45635-52 05.86 Measurement of airborne noise emitted by machines; enveloping surfacemethod; mine diesel locomotives and mine road railers (5) /FABERG co-author/

DIN 45635-53 05.86 Measurement of airborne noise emitted by machines; enveloping surfacemethod; diesel traction trolleys (5) /FABERG co-author/

DIN 45635-54 05.86 Measurement of airborne noise emitted by machines; enveloping surfacemethod; mine trackless vehicles (5) /FABERG co-author/

DIN 45635-55 05.86 Measurement of airborne noise emitted by machines; enveloping surfacemethod; shunting trolleys with friction- wheel and/or gearwheel drive (5)/FABERG co-author/

NA 008-05-02 AA Suspended monorails

DIN 20590 04.90 Securing devices on underframes used in mining (5)DIN 20592-1 08.91 Suspended monorails for mining; transport boxes; dimensions and

requirements (5)DIN 20592-2 08.91 Suspended monorails for mining; attachment facilities for transport boxes;

dimensions and requirements (5)DIN 20593-1 11.02 Monorails for mining - Rails - Part 1: Straight rails for profile I 140 E (7)

DIN 20593-2 11.02 Monorails for mining - Rails - Part 2: Curved rails and adapting rails for profile I140 E (8)DIN 20593-3 07.04 Monorails for minging - Rails - Part 3: Straight rails and rail-connections for

profiles I 140V and I 250 (11)DIN 20593-4 04.07 Monorails for minging - Rails - Part 4: Curved rails and adapting rails for profiles

I 140 V and I 250 (12)DIN 20594 08.91 Suspension claws for mining, for loads up to 30 kN; requirements and testing (7)DIN 20597 05.92 Suspended monorails for mining; toothed disc (5)DIN 20599 08.93 Suspended monorails for mining; rope positions, mounting devices, clearance

dimensions for bogies (5)DIN 20619 08.93 Suspended monorails for mining; winding-drum with suspension hook;

dimensions and requirements (6)DIN 20620-1 10.94 Force-guided tram-ways in mining - Part 1: Survey; structure and terms (5)DIN 20620-2 10.94 Force-guided tram-ways in mining - Part 2: Monorails; structure and terms (6)DIN 20620-3 10.94 Force-guided tram-ways in mining - Part 3: Free-steered machines; structure

and terms (6)DIN 20622 11.02 Suspended-monorail transport systems for mining - Permissible loads for

suspensions and their abnutments and railprofile I 140 E (10)DIN 20625-1 03.92 Capture-track rail installations in mining; bolted couplings for rope-hauled and

self-propelled rail installations; bolted coupling 30 (7)DIN 20629-1 08.01 Suspended monorails for mining - Mounting regulations - Part 1: for cable-

driven suspended monorails (7)DIN 20629-2 08.01 Suspended monorails for mining - Mounting regulations - Part 2: for loco-driven

suspended monorails (8)DIN 20629-3 08.01 Suspended monorails for mining - Mounting regulations - Part 3: Calculations (5)DIN 20633 04.02 Overhead monorail installations for mining - Double-end fork turnbuckles (7)DIN 20635 05.01 Monorails for mining - Suspensions shackles (6)DIN 20636 06.01 Monorails for mining - Suspension claws - Requirements and testing (5)DIN 20637 10.97 Monorails for mining - Tested round steel chains for suspensions - Tested, long

link (5)

NA 008-05-03 AA Belt conveyorsDIN EN ISO 252 01.08 Conveyor belts - Ply adhesion between constitutive eleents - Test methods (ISO

252:2007); German version EN ISO:2007 (8) /FABERG co-author/



14/45


DIN EN ISO 283 02.08 Textile conveyor belts - Full thickness tensile strength, elongation at break andelongation at the reference load - Test method (ISO 283:2007); Germanversion EN ISO 283:2007 (9) /FABERG co-author/

DIN EN ISO 284 04.04 Conveyor belts - Electrical conductivity - Specification and method of test (ISO284:2003); German Version EN ISO 284:2003 (8) /FABERG co-author/

DIN EN ISO 340 06.07 Conveyor belts - Laboratory scale flammability characteristics - Requirementsand test method (ISO 340:2004); German version EN ISO 340:2004 (8)

/FABERG co-author/DIN EN ISO 340/B1 09.09 Conveyor belts - Laboratory scale flammability characteristics - Requirements

and test method (ISO 340:2004); German version EN ISO 340:2004,Corrigendum to DIN EN ISO 340:2007-06 (99) /FABERG co-author/

DIN EN ISO 505 04.00 Conveyor belts - Method for the determination of the tear propagationresistance of textile conveyor belts (ISO 505:1999); German version EN ISO505:1999 (6) /FABERG co-author/

DIN EN ISO 583 03.08 Conveyor belts with a textile carcass - Total belt thickness and thickness of constitutive elements - Method of test (ISO 583:2007); German version ENISO 583:2007 (9) /FABERG co-author/

DIN EN ISO 703 03.08 Conveyor belts - Transverse flexibility (troughability) - Test method (ISO703:2007); German version EN ISO 703:2007 (8) /FABERG co-author/

DIN EN ISO 1120 06.02 Conveyor belts - Determination of strength of mechanical fastenings - Static testmethod (ISO 1120:2002); German version EN ISO 1120:2002 (7) /FABERG co-author/

DIN EN 1554 01.99 Conveyor belts - Drum friction testing; German version EN 1554:1998 (6)/FABERG co-author/

DIN EN ISO 7590 03.10 Steel cord conveyor belts - Methods for the determination of total thickness andcover thickness (ISO 7590:2001); German version EN ISO 7590:2001 (8)/FABERG co-author/

DIN EN ISO 7622-1 11.95 Steel cord conveyor belts - Longitudinal traction test - Part 1: Measurement of elongation (ISO 7622-1:1984); German version EN ISO 7622-1:1995 (5)/FABERG co-author/

DIN EN ISO 7622-2 11.95 Steel cord conveyor belts - Longitudinal traction test - Part 2: Measurement of tensile strength (ISO 7622-2:1984); German version EN ISO 7622-2:1995 (6)/FABERG co-author/

DIN EN ISO 7623 08.97 Steel cord conveyor belts - Cord-to-coating bond test - Initial test and afterthermal treatment (ISO 7623:1996); German version EN ISO 7623:1997 (6)/FABERG co-author/

DIN EN ISO 9856 07.04 Conveyor belts - Determination of elastic and permanent elongation andcalculation of elastic modulus (ISO 9856:2003); German version EN ISO9856:2003 (8) /FABERG co-author/

DIN EN 12881-1 01.10 Conveyor belts - Fire simulation flammability testing - Part 1: Propane burnertests; German version EN 12881-1:2005+A1:2008 (14) /FABERG co-author/

DIN EN 12881-2 10.09 Conveyor belts - Fire simulation flammability testing - Part 2: Large scale firetest; German version EN 12881-2:2005+A1:2008 (8) /FABERG co-author/

DIN EN 12882 03.10 Conveyor belts for general purpose use - Electrical and flammability safetyrequirements; German version EN 12882:2008 (11) /FABERG co-author/

DIN EN 13827 07.04 Steel cord conveyor belts - Determination of the lateral and verticaldisplacement of steel cords; German version EN 13827:2003 (7) /FABERG co-author/

DIN EN ISO 14890 11.05 Conveyor belts - Specification for rubberor plastics covered conveyor belts of textile construction for general use (ISO 14890:2003); German version EN ISO14890:2003 (12) /FABERG co-author/

DIN EN 14973 12.09 Conveyor belts for use in underground installations - Electrical and flammabilitysafety requirements; German version EN 14973:2006+A1:2008 (11) /FABERGco-author/

DIN 15207-1 10.00 Continuous mechanical handling equipment - Idlers for belt conveyors - Maindimensions of idlers for belt conveyors for bulk material (5) /FABERG co-author/



15/45


DIN EN ISO 15236-1 04.06 Steel cord conveyor belts - Part 1: Design, dimensions and mechanicalrequirements for conveyor belts for general use (ISO 15236-1:2005); Germanversion EN ISO 15236-1:2005 (12) /FABERG co-author/

DIN EN ISO 15236-2 09.04 Steel cord conveyor belts - Part 2: Preferred belt types (ISO 15236-2:2004);German version EN ISO 15236-2:2004 (8) /FABERG co-author/

DIN EN ISO 15236-3 04.08 Steel cord conveyor belts - Part 3: Special safety requirements for belts for usein underground installations (ISO 15236-3:2007); German version EN ISO

15236-3:2007 (11) /FABERG co-author/DIN EN ISO 15236-4 09.04 Steel cord conveyor belts - Part 4: Vulcanized belt joints (ISO 15236-4:2004);

German version EN ISO 15236-4:2004 (8) /FABERG co-author/DIN EN ISO 16851 03.05 Textile conveyor belts - Determination of the net length of an endless (spliced)

conveyor belt (ISO 16851:2004); German version EN ISO 16851:2004 (7)/FABERG co-author/

DIN 22101 08.02 Continuous conveyors - Belt conveyors for loose bulk materials - Basis forcalculation and dimensioning (17)

DIN 22101 02.10 Continuous conveyors - Belt conveyors for loose bulk materials - Basis forcalculation and dimensioning (20)

E

DIN 22102-1 04.91 Conveyor belts with textile plies for bulk goods - Part 1: Dimensions,specifications, marking (7) /FABERG co-author/

DIN 22102-2 04.91 Conveyor belts with textile plies for bulk goods - Part 2: Testing (5) /FABERG coauthor/

DIN 22102-3 04.91 Conveyor belts with textile plies for bulk goods - Part 3: Permanent joints (6)/FABERG co-author/

DIN 22107 08.84 Continous mechanical handling equipment; idler sets for belt conveyors forloose bulk materials; principal dimensions (5) /FABERG co-author/

DIN 22109-1 07.00 Conveyor belts with textile plies for coalmining - Part 1: Monoply belts forunderground applications; dimensions, requirements (6)

DIN 22109-2 07.00 Conveyor belts with textile plies for coalmining - Part 2: Rubber-belts with twoplies for underground applications; dimensions, requirements (6)

DIN 22109-4 07.00 Conveyor belts with textile plies for coalmining - Part 4: Rubber-belts with twoplies for above ground applications; dimensions, requirements (6)

DIN 22109-5 02.88 Conveyor belts with textile plies for coalmining; branding (5)DIN 22109-6 12.03 Conveyor belts with textile plies for coalmining - Part 6: Testing (6)DIN 22110-2 10.97 Testing methods for conveyor belt joints - Part 2: Endurance running tests,

determination of running time of belt joints at conveyor belts with textile plies (5)DIN 22110-3 11.07 Testing methods for conveyor belt joints - Part 3: Determination of time strength

for conveyor belt joints (dynamical testing method) (8)DIN 22117 02.88 Conveyor belts for coalmining; determination of the oxygen index (6)DIN 22121 07.00 Conveyor belts with textile plies for coalmining - Permanent joints for belts with

one or two plies; dimensions, requirements, marking (6)DIN 22122 10.03 Continous mechanical handling equipment - Troughability of conveyor belts -

Determination of that portion of width of conveyor belting in contact with idlers,requrements, testing (6)

DIN 22129-1 02.88 Steel cord conveyor belts for underground coalmining; dimensions,requirements (6)

DIN 22129-2 02.88 Steelcord conveyor belts for underground coalmining; marking (5)DIN 22129-3 02.88 Steelcord conveyor belts for underground coalmining; testing (6)DIN 22129-4 11.91 Steelcord conveyor belts for use in underground coal mining; belt joints;

dimensions, requirements (6)

DIN 22131-2 11.88 Steelcord conveyor belts for hoisting and conveying; marking (5)DIN 22131-3 11.88 Steelcord conveyor belts for hoisting and conveying; testing (5)



16/45


DIN EN ISO 22721 01.10 Conveyor belts - Specification for rubber- or plastics-covered conveyor belts of textile construction for underground mining (ISO 22721:2007); German versionEN ISO 22721:2007 (11) /FABERG co-author/

DIN EN 28094 05.94 Steel cord conveyor belts; adhesion strength test of the cover to the core layer(ISO 8094:1984); German version EN 28094:1994 (5) /FABERG co-author/

DIN 53530 02.81 Testing of organic materials; Separation test on fabric plies bonded together (5)/FABERG co-author/

NA 008-05-04 AA Constructions for belt conveyors

DIN 22111 11.07 Belt conveyors for underground coal mining - Light construction (11)DIN 22112-1 12.10 Belt conveyors for underground coal mining - Idlers - Part 1: Dimensions (6)DIN 22112-2 12.10 Belt conveyors for underground coal mining - Idlers - Part 2: Requirements (5)DIN 22112-2 03.96 Belt conveyors for underground coalmining - Idlers - Part 2: Requirements (5)DIN 22112-3 03.96 Belt conveyors for underground coalmining - Idlers - Part 3: Testing (7)DIN 22114 12.10 Belt conveyors for underground coalmining - Heavy construction (12)DIN 22114/B1 12.03 Corrigenda to DIN 22114:2001-12

DIN 22114 12.01 Belt conveyors for underground coalmining - Heavy construction (8)DIN 22115 10.03 Belt conveyors for underground coalmining; Coating on idlers; Requirementsand testing (7)

DIN 22116 10.03 Belt conveyors for underground coal mining - Pressure rollers DN 159 -Dimensions, requirements, marking (6)

DIN 22120 04.05 Elastomere scraper plates for belt conveyors in hard coal mines (6)

NA 008-05-05 AA Component s for chain conveyors

DIN 763 12.90 Tested, non-calibrated, long-link round steel chains (5) /FABERG co-author/DIN 8175 02.80 Conveyor chains; bush conveyor chains, heavy type (4) /FABERG co-author/

DIN 8176 01.80 Conveyor chains; bush conveyor chains for haulage systems (4) /FABERG co-author/DIN EN 12321 07.09 Underground mining machinery - Specification for the safety requirements for

armoured face conveyors; German version EN 12321:2003+A1:2009 (12)DIN 22200 05.94 Continous mechanical handling equipment; idler sets for belt conveyors for

loose bulk materials; principal dimensions (5) /FABERG co-author/BB 22249 12.72 Schmiernippel fr den Bergbau (2)DIN 22252 09.01 Round steel link chains for conveyors and winning equipment in mining (9)DIN 22252 04.10 Round steel link chains for use in continuous conveyors and winning equipment

in mining (11)E

DIN 22253 03.08 Chain connectors - Shackle type connector units - Dimensions, requirements,testing (12)

DIN 22255 08.01 Flat link chains for use in continuous conveyors in mining (9)DIN 22255 08.10 Flat link chains for use in continuous conveyors in mining (12)EDIN 22256 10.02 Chain sprockets for chain conveyors and coal winning equipment - Dimensions,

requirements, testing (11)DIN 22257 06.90 Scraper bars for chain conveyors; outboard chain assembly; dimensions,

requirements, testing (5)DIN 22258-1 04.03 Chain connectors - Part 1: Flat type connectors (9)DIN 22258-1 08.10 Chain connectors - Part 1: Flat type connectors - Inactive for new design (10)EDIN 22258-2 08.03 Chain connectors - Part 2: Kenter type connectors (9)DIN 22258-3 08.03 Chain connectors - Part 3: Block type connectors (8)DIN 22258-3 08.10 Chain connectors - Part 3: Block type connectors (10)E



17/45


DIN 22259 05.07 Flightbars for use in chain conveyors in mining (10)

NA 008-05-06 AA Pipe systems

DIN 20002-1 11.89 Pipelines for mining; steel tubes with loose flanges and plain collars; nominalpressure 10 (5)

DIN 20002-2 11.89 Pipelines for mining; steel tubes with loose flanges and collars; projection andrecess; nominal pressure 6 (5)

DIN 20002-3 11.89 Pipelines for mining; steel tubes with loose flanges and plain collars; nominalpressure 40 (5)

DIN 20003-1 09.87 Steel tubes for mining; fittings with loose flanges and plain collars; nominalpressure 10 (7)

DIN 20003-2 09.87 Steel tubes for mining; fittings with loose flanges and plain collars, projectionand recess; nominal pressure 6 (7)

DIN 20003-3 09.87 Steel tubes for mining; fittings with loose flanges and plain collars; nominalpressure 40 (6)

DIN 20004-1 12.00 Steel tubes for mining - Part 1: Interpose rings rated for PN 10 and PN 40 (6)DIN 20004-2 12.00 Steel tubes for mining - Part 2: Wedge rings rated for PN 10 and PN 40 (5)

DIN 20006 09.89 Pipeline for mining; sealings for steel tubes according to DIN 20002 and fittingsaccording to DIN 20003 (5)DIN 20042 08.01 Watervalve, nominal pressure 40 - Dimensions and requirements (5)BB 20065-1 02.78 Kunststoff-Rohrleitungen - Richtlinien fr die Verlegung - Thermoplastische

Kunststoffe (2)BB 20065-2 02.78 Kunststoff-Rohrleitungen - Richtlinien fr die Verlegung - Mitgeltende Normen

(2)DIN 24251 08.73 Multistage centrifugal pumps; mine drainage pumps, with pump total head up to

1000 m at speed of rotation 1500 l/min (4) /FABERG co-author/

NA 008-05-07 AA Hose assemblies

DIN EN 853 02.97 Rubber hoses and hose assemblies - Wire braid reinforced hydraulic type -Specification; German version EN 853:1996 (7) /FABERG co-author/

DIN EN 854 02.97 Rubber hoses and hose assemblies - Textile reinforced hydraulic type -Specification; German version EN 854:1996 (7) /FABERG co-author/

DIN EN 856 02.97 Rubber hoses and hose assemblies - Rubber-covered spiral wire reinforcedhydraulic type - Specification; German version EN 856:1996 (7) /FABERG co-author/

DIN EN 857 02.97 Rubber hoses and hose assemblies - Wire braid reinforced compact type forhydraulic applications - Specification; German version EN 857:1996 (6)/FABERG co-author/

DIN EN ISO 1402 04.10 Rubber and plastic hoses and hose assemblies - Hydrostatic testing (ISO1402:2009); German version EN ISO 1402:2009 (10) /FABERG co-author/

DIN EN ISO 7751 06.97 Rubber and plastics hoses and hose assemblies - Ratios of proof and burstpressure to design working pressure (ISO 7751:1991); German version EN ISO7751:1997 (5) /FABERG co-author/

DIN EN ISO 8030 02.98 Rubber and plastics hoses - Method of test for flammability (ISO 8030:1995);German version EN ISO 8030:1997 (6) /FABERG co-author/

DIN EN ISO 8031 04.10 Rubber and plastics hoses and hose assemblies - Determination of electricalresistance and electrical conductivity (ISO 8031:2009); German version EN ISO8031:2009 (12) /FABERG co-author/

DIN EN ISO 8033 11.06 Rubber and plastics hoses - Determination of adhesion between components(ISO 8033:2006); German version EN ISO 8033:2006 (10) /FABERG co-author/

DIN EN ISO 8330 02.10 Rubber and plastics hoses and hose assemblies - Vocabulary (ISO8330:2007); German version prEN ISO 8330:2007 (14) /FABERG co-author/

DIN 20018-1 04.03 Textile-reinforced hoses - Part 1: Maximal working pressure PN 10/16 (7)



18/45


DIN 20018-2 04.03 Textile-reinforced hoses - Part 2: Maximal working pressure PN 40 (5)DIN 20018-3 04.03 Textile-reinforced hoses - Part 3: Maximal working pressure PN 100 (5)DIN 20018-4 04.03 Textile-reinforced hoses - Part 4: Testing (6)DIN 20021 02.97 Fluid-systems - Hoses with layer - Completation for DIN EN 853 to DIN EN 857

(5)DIN 20029 10.90 Hose fittings; 1:3 taper gauges (5)

DIN 20030 06.92 Hose fittings; straight-way-cock with grip; dimensions, materials, requirements(5)DIN 20033 07.90 Hose fittings; tapered nozzle with clamping nut (6)DIN 20035 10.90 Hose fittings; flange nozzle; nominal pressure 16 (5)DIN 20036 10.90 Hose fittings; coupling nipples with round thread form (5)DIN 20037 10.90 Hose fittings; connecting nipple; dimensions (5)DIN 20038 10.90 Hose fittings; coupling nozzles (5)DIN 20039 08.98 Hose fittings - Hose clamps (5)DIN 20040 10.90 Hose fittings; nipple valves; nominal pressure 16 (5)

DIN 20043 09.03 Staple-lock couplings for hydraulic power-transmission circuits (7)DIN 20044 05.03 Staple-lock couplings type S for hydraulic power-transmission circuits -

Dimensions, requirements, testing (7)DIN 20066 10.02 Hoses and hose assemblies; test methods suggestion for the configuration of

documents (11) /FABERG co-author/DIN 20066 10.10 Hydraulic fluid power - Hose assemblies - Dimensions, requirements (12)

/FABERG co-author/E

NA 008-05-08 AA Mobile machines

DIN EN 1889-1 11.03 Machines for underground mines - Mobile machines working underground;safety - Part 1: Rubber tyred vehicles; German version EN 1889-1:2003 (15)

/FABERG co-author/DIN EN 1889-2 07.09 Machines for underground mines - Mobile machines working underground -

Safety - Part 2: Rail locomotives; German version EN 1889-2:2003+A1:2009(20)

DIN EN 12111 05.10 Tunnelling machines - Road headers, continuous miners and impact rippers -Safety requirements; German version EN 12111:2002+A1:2009 (16) /FABERGco-author/



19/45

FB Ventilation 06Register of Mining Standards 2010-12

06 Ventilation

NA 008-06-01 AA Air doors

DIN EN 12110 02.10 Tunnelling machines - Air locks - Safety requirements; German version EN12110:2002+A1:2008 (12) /FABERG co-author/

DIN 21631 01.93 Air regulating systems in mining; wing air doors for travelling tracks; air doorswithout pressure reduction (7)

DIN 21631 02.09 Air regulating systems for mining - Wing air doors for travelling tracks - One-wing type air doors without pressure reduction (11)

E

DIN 21632 01.93 Air regulating systems in mining; wing air doors for haulage tracks; one-wingtype doors without pressure reduction (7)

DIN 21632 02.09 Air regulating systems for mining - Wing air doors for haulage tracks - One-wingtype doors without pressure reduction (10)

E

DIN 21633 10.93 Air regulating systems in mining; wing air doors for haulage tracks; double-wingtype doors without pressure reduction (9)

DIN 21633 03.09 Air regulating systems for mining - Wing air doors for haulage tracks - Double-wing type doors without pressure reduction (12)

E

DIN 21634 05.99 Air regulation systems in mining - Swinging roadway air doors for monorails andfree steered machines - Building and operation (9)

DIN 21634 08.09 Air regulation systems for mining - Swinging roadway air doors for haulagetracks (10)

E

DIN 21635 02.98 Air regulation systems in mining - Air locks - Building and operation (7)DIN 21636 04.03 Air regulation systems in mining - Belt-conveyors-way air locks - Dimensions,

identifications, requirements and testing (12)DIN 21637 10.95 Air regulation systems in mining - Wing air doors for haulage tracks - Double-

wing type doors with pressure reduction (8)DIN 21638 05.99 Air regulation systems in mining - Wing air locks for travelling tracks - Double-

wing type doors with pressure reduction (6)DIN 21639 09.99 Air regulation systems in mining - Travel-way air locks - Type doors with

pressure (5)DIN 21639/B1 11.04 Corrigenda to DIN 21639:1999-09DIN 21640-1 10.93 Air regulating systems in mining; pneumatic cylinders for airdoors without

pressure reduction; dimensions, requirement, marking (5)

NA 008-06-02 AA Installations for auxiliary ventilation

DIN 21603 10.09 Auxiliary ventilation for mining - Sheet airducting with collars and loose flanges(5)

DIN 21605 07.10 Auxiliary ventilation for mining - Flexible plastic ventilation ducts for exhaust andforced ventilation - Spiral ventilation ducts (6)

DIN 21606 07.10 Auxiliary ventilation for mining - Flexible plastic ventilation ducts for forcedventilation - Flat ventilation ducts (6)

DIN 21610 07.10 Auxiliary ventilation in mining - Flexible plastic air ducts - Requirements and testmethods (6)

DIN 21612 07.10 Auxiliary ventilation for mining - Cladding material for flexible airducts -Requirements, testing (5)

DIN 21613 10.09 Auxiliary ventilation for mining - Steel sheet connectors with flange and shoulder(5)

DIN 21614 10.09 Auxiliary ventilation for mining - Flanged sheet steel reducers (5)

DIN 21615 10.09 Auxiliary ventilation for mining - Sheet steel reducers with flange and shoulder(5)DIN 21625 07.10 Fans with electric motor drive intended for use in potentially explosive

atmospheres in coal mines (6)



20/45

FB Ventilation 06Register of Mining Standards 2010-12

DIN 21626 07.10 Fans with hybrid (electric/pneumatic) motor drive intended for use in potentiallyexplosive atmospheres in coal mines (6)



21/45

FB Mine Safety 07Register of Mining Standards 2010-12

07 Mine Safety

NA 008-07-01 AA Personal safety and protect ive equipment

DIN EN 795/A1 01.01 Protection against falls from a height - Anchor devices - Requirements andtesting; Amendment A1; German version EN 795:1996/A1:2000 (6) /FABERGco-author/

DIN EN 795 08.96 Protection against falls from a height - Anchor devices - Requirements andtesting; German version EN 795:1996 (10) /FABERG co-author/DIN EN 795 06.09 Personal fall protection equipment - Anchor devices; German version prEN

795:2009 (15) /FABERG co-author/E

DIN EN 1497 10.07 Personal fall protection equipment - Rescue harnesses; German version EN1497:2007 (10) /FABERG co-author/

DIN EN 1498 01.07 Personal fall protection equipment - Rescue loops; German version EN1498:2006 (11) /FABERG co-author/

DIN 5290-1 04.83 Snap hook from light metal; with setting nut; dimensions, requirements andtesting (5) /FABERG co-author/

DIN 7472-2 01.91 Safety harness; steel fittings; connecting dimensions, safety requirements andtesting (6) /FABERG co-author/

DIN EN ISO 14122-1 01.02 Safety of machinery - Permanent means of access to machinery - Part 1:Choise of fixed means of access between tow levels (ISO 14122-1:2001);German version EN ISO 14122-1:2001 (8) /FABERG co-author/

DIN EN ISO 14122-2 01.02 Safety of machinery - Permanent means of access to machinery - Part 2:Working platforms and wlkways (ISO 14122-2:2001); German version EN ISO14122-2:2001 (7) /FABERG co-author/

DIN EN ISO 14122-3 01.02 Safety of machinery - Permanent means of access to machinery - Part 3: Stairs,stepladders and guard-rails (ISO 14122-3:2001); German version EN ISO14122-3:2001 (9) /FABERG co-author/

DIN EN ISO 14122-4 12.04 Safety of machinery - Permanent means of access to machinery - Part 4: Fixedladders (ISO 14122-4:2004); German version EN ISO 14122-4:2004 (14)/FABERG co-author/

DIN EN 14404 02.05 Personal protective equipment - Knee protectors for work in the neeling position;German version EN 14404:2004 (12) /FABERG co-author/

DIN 20180 06.10 Pulley for clothes hoists in pithead baths (5)DIN 20182 06.10 Double loop chain for hoisting clothes in pithead baths - Not tested, non-

calibrated (4)DIN EN ISO 20344 11.07 Personal protective equipment - Test methods for footwear (ISO

20344:2004+Amd.1:2007); German Version EN ISO20344:2004+AC:2005*A1:2007 (26) /FABERG co-author/

DIN EN ISO 20345 12.07 Personal protective equipment - Safety footwear (ISO20345:2004+AMD1:2007); German Version EN ISO20345:2004+AC:2007+A1:2007 (15) /FABERG co-author/

DIN EN ISO 20345 05.09 Personal protective equipment - Safety footwear (ISO/DIS 20345:2009);German version prEN ISO 20345:2009 (16) /FABERG co-author/

E

DIN EN ISO 20346 12.07 Personal protective equipment - P rotective footwear (ISO20346:2004+AMD1:2007); German version EN ISO20346:2004+AC:2007+A1:2007 (15) /FABERG co-author/

DIN EN ISO 20346 05.09 Personal protective equipment - Protective footwear (ISO/DIS 20346:2009);German version prEN ISO 20346:2009 (16) /FABERG co-author/

E

DIN EN ISO20347/B1

08.07 Personal protective equipment - Occupational footwear (ISO 20347:2004);German Version EN ISO 20347:2004, Corrigenda to DIN EN ISO 20347:2004-10; German version EN ISO 20347:2004/AC:2007 (99) /FABERG co-author/

DIN EN ISO 20347 12.07 Personal protective equipment - Occupational footwear (ISO20347:2004+AMD1:2007); German version EN ISO20347:2004+AC:2007+A1:2007 (15) /FABERG co-author/



22/45


DIN 21800 06.89 Symbol mallet and iron (5)DIN 21802 06.89 Symbols for mine rescue and gas protection squads (6)DIN 23301 03.07 Safety footwear for underground mining (9)DIN 23307 06.09 Leather backside protectors for miners (back skin) (5)DIN 23311-1 06.85 Knee pads for mining; rubber knee pads (5)DIN 23311-2 02.98 Knee pads for mining - Part 2: Plastic knee pads (6)DIN 23320-1 04.98 Flameproof protective clothing for the mining industry - Part 1: Safety

requirements and testing (5)DIN 23320-2 09.03 Flameproof protective clothing for the mining industry - Protecting clothing for

people of mine rescue, gas rescue and fire rescue crews - Part 2: Single pieceworking suits (combinations) (5)

DIN 23320-3 09.03 Flameproof protective clothing for the mining industry - Protecting clothing forpeople of mine rescue, gas rescue and fire rescue crews - Part 3: Two-pieceworking suits (5)

DIN 23320-4 09.03 Flameproof protective clothing for the mining industry - Protecting clothing forpeople of mine rescue, gas rescue and fire rescue crews - Part 4: Underwear (5)

DIN 23320-5 10.04 Flameproof protective clothing for the mining industry - Protecting clothing forpeople of mine rescue, gas rescue and fire rescue crews - Part 5: Protectivehoods (7)

DIN 23323 05.07 Bathing sandals for miners (5)DIN 23327 07.03 Shin protectors for mining (7)DIN 23328 09.03 Clothing for the mining industry - Woven farbics for work suits (6)DIN 23330 11.01 Safety markings for mines (15)DIN 23341 05.05 Clothing for the mining industry - Two-piece work suits (J acket and trousers) (7)DIN 23342 08.05 Clothing for the mining industry - Singlet with 1/4 sleeves (7)DIN 23343 03.07 Clothing for the mining industry - Shirt for miners (7)

DIN 23344 09.03 Clothing for the mining industry - Men's slip (6)DIN 23345 08.05 Clothing for the mining industry - Long underpants (7)DIN 23346 09.03 Clothing for the mining industry - Socks for mining workers (6)DIN 23400 11.08 Rescue stretcher for mining (dragging basket) - Safety requirements and testing

(10)DIN 23405 10.04 First aid boxes and first aid material for use in mining (6)DIN 24320 12.06 Fire resistant fluids - Hydraulic fluids of categories HFAE and HFAS -

Characteristics and requirements (7) /FABERG co-author/DIN 24531-1 04.06 Gratings used as stairtreads - Part 1: Metal gratings (7) /FABERG co-author/DIN 24531-2 08.07 Gratings used as stairtreads - Part 2: Sheet metal gratings (7) /FABERG co-

author/DIN 24531-3 08.07 Gratings used as stairtreads - Part 3: Plastic gratings (6) /FABERG co-author/DIN 24534 03.70 Chain locks (4) /FABERG co-author/DIN 24537-1 04.06 Gratings used as floor coverings - Part 1: Metal gratings (7) /FABERG co-authorDIN 24537-2 08.07 Gratings used as floor coverings - Part 2: Sheet metal gratings (7) /FABERG co-

author/DIN 24537-3 08.07 Gratings used as floor coverings - Part 3: Plastic gratings (7) /FABERG co-

author/DIN 34300 04.01 Rescue equipment - Rescue hooks with safety eyelet holes (6) /FABERG co-

author/

DIN 51502 08.90 Designation of lubricants and marking of lubricant containers, equipment andlubricating points (7) /FABERG co-author/

DIN 51634 12.81 Mineral spirits; safety lamps mineral spirit; minimum requirements (5)/FABERG co-author/



23/45


NA 008-07-02 AA Lighting

DIN 20609 11.93 Lighting of mine locomotives; head lamps; design features, photometricrequirements, meters and measurements (6)

DIN 20610 04.94 Lighting of mine locomotives; position lamps; design features, photometricrequirements (5)

DIN 22433 10.03 Underground lighting in hardcoal mining - Terms (6)DIN 22434-1 07.01 Underground lighting in hardcoal mining - Lighting-technological planning

bases - Part 1: General specification (6)DIN 22434-2 02.03 Underground lighting in hardcoal mining - Lighting-technological planning

bases - Part 2: Coalfaces with shield support (5)DIN 22434-3 02.03 Underground lighting in hardcoal mining - Lighting-technological planning

bases - Part 3: T-junctions (5)DIN 22434-4 11.96 Underground lighting in hardcoal mining - Lighting-technological planning

bases - Part 4: Conveyor belt (5)DIN 22434-5 02.03 Underground lighting in hardcoal mining - Lighting-technological planning

bases - Part 5: Material handling places (5)

DIN 22434-6 02.03 Underground lighting in hardcoal mining - Lighting-technological planningbases - Part 6: Area of roadway-driving operation (5)DIN 22434-7 07.95 Underground lighting in hardcoal mining - Lighting-technological planning

bases - Part 7: Pit-bottom (5)DIN 22434-8 01.04 Underground lighting in hardcoal mining - Lighting-technological planning

bases - Part 8: Building sites (5)DIN 22434-9 10.98 Underground lighting in hardcoal mining - Lighting-technological planning

bases - Part 9: Areas of rail track operation (5)DIN 22434-10 02.05 Underground lighting in hardcoal mining - Lighting-technological planning

bases - Part 10: Workshops and special premises (6)DIN 49659 12.86 Fluorescent lamps, non preheated for potentially explosive atmospheres (5)

/FABERG co-author/DIN 49741 11.68 Lamp cap BX22d/32 (4) /FABERG co-author/DIN 49834 08.69 Electric lamps for portable miner's luminaires (4) /FABERG co-author/

NA 008-07-02-01 AK Caplight s

DIN EN 62013-1 02.07 Caplights for use in mines susceptible to firedamp - Part 1: Generalrequirements - Construction and testing in relation to the risk of explosion (IEC62013-1:2005); German version EN 62013-1:2006 (16) /FABERG co-author/

DIN EN 62013-2 02.07 Caplights for use in mines susceptible to firedamp - Part 2: Performance andother safety-related matters (IEC 62013-2:2005); German version EN 62013-2:2006 (12) /FABERG co-author/

NA 008-07-03 AA Explosion prevention and protection

DIN EN 1127-2 07.10 Explosive atmospheres - Explosion prevention and protection - Part 2: Basicconcepts and methodology in mining; German version EN 1127-2:2002+A1:2008 (17)

DIN EN 1710 08.08 Equipment and components intended for use in potentially explosiveatmospheres in underground mines; German version EN 1710:2005+A1:2008(17)

DIN EN 13463-1 07.09 Non-electrical equipment for use in potentially explosive atmospheres - Part 1:Basic method and requirements; German versionrEN 13463-1:2009 (26)/FABERG co-author/

DIN EN 13463-5 03.04 Non-electrical equipment for potentially explosive atmospheres - Part 5:Protection by constructional safety "c"; German version EN 13463-5:2003 (13)/FABERG co-author/



24/45


DIN EN 14591-1/B1 06.06 Explosion prevention and protection in underground mines - Protectivesystems - Part 1: 2-bar explosion proof ventilation structures, Corrigenda to DINEN 14591-1:2004-12; German version EN 14591-1:2004/AC.2006 (99)

DIN EN 14591-1 12.04 Explosion prevention and protection in underground mines - Protectivesystems - Part 1: 2-bar explosion proof ventilation structures; German versionEN 14591-1:2004 (10)

DIN EN 14591-2 07.07 Explosion prevention and protection in underground mines - Protective

systems - Part 2: Passive water trough barriers; German Version EN 14591-2:2007 (17)DIN EN 14591-4 09.07 Explosions prevention and protection in underground mines - Protective

systems - Part 4: Automatic extinguishing systems for road headers; Germanversion prEN 14591-4:2005 (9)

DIN EN 14983 06.07 Explosion prevention and protection in underground mining - Equipment andprotective systems for firedamp drainage; German version EN 14983:2007 (13)

DIN 21577 09.96 Explosibility of coal dust in underground hard coal mining - Tests andassessments of coal dust-air-mixtures and hybrid mixtures (8)

DIN EN 50303 05.01 Group 1, category M1 equipment intended to remain functional in atmospheresendangered by firedamp and/or coal dust; German version EN 50303:2000 (7)/FABERG co-author/

NA 008-07-03-01 AK Apparatus for potentially explosive atmospheres for mining

DIN EN 1834-2 03.00 Reciprocating internal combustion engines - Safety requirements for design andconstruction of engines for use in potentially explosive atmospheres - Part 2:Group I engines for use in underground workings susceptible to firedamp and/orcombustible dust; German version EN 1834-2:2000 (10) /FABERG co-author/

DIN 20401 12.04 Buttress threads - 0,8 mm to 2 mm pitch - Dimensions (6)DIN 22412 04.86 Slit-bolts (5) /FABERG co-author/DIN 22416 09.86 Electrical apparatus for potentially explosive atmospheres in mining; triangular

head bolts; safety requirements and testing (5)

DIN 22417 11.88 Electrical apparatus for potentially explosive atmospheres; forms of keys fortriangular socket wrenches (5)DIN 22418 04.89 Electrical apparatus for potentially explosive atmospheres for mining; screw

plugs; safety requirements and testing (6)DIN 22419-1 12.04 Electrical apparatus for potentially explosive atmospheres for mining - Cable

entries - Part 1: Requirements for basic design (8)DIN 22419-2 12.04 Electrical apparatus for potentially explosive atmospheres for mining - Cable

entries - Part 2: Gland adaptors for entries; safety requirements and testing (6)DIN 22419-3 12.04 Electrical apparatus for potentially explosive atmospheres for mining - Cable

entries - Part 3: Gland flanges for entries; safety requirements and testing (7)DIN 22424 03.90 Electrical apparatus for potentially explosive atmospheres for mining; triangle

head bolts (6)DIN 22425 03.90 Electrical apparatus for potentially explosive atmospheres for mining; triangular

nuts (6)DIN 46295-1 04.85 Terminal board, square shaped with six slit-bolts; main dimensions (5)

/FABERG co-author/DIN 46295-2 10.81 Terminal board, square shaped with six slit-bolts; accessories (6) /FABERG co-

author/DIN 46295-3 10.81 Terminal board, square shaped with six slit-bolts; cable sockets (5) /FABERG

co-author/

NA 008-07-04-01 AK Explosives

DIN EN 13631-1 07.05 Explosives for civil uses - High explosives - Part 1: Requirements; Germanversion EN 13631-1:2005 (7)



25/45


DIN EN 13631-2 12.02 Explosives for civil uses - High explosives - Part 2: Determionation of thermalstability of explosives; German version EN 13631-2:2002 (7)

DIN EN 13631-3 11.04 Explosives for civil uses - High explosives - Part 3: Determionation of sensitiveness to friction of explosives; German version EN 13631-3:2004 (8)

DIN EN 13631-4 12.02 Explosives for civil uses - High explosives - Part 4: Determionation of sentiveness to impact of explosives; German version EN 13631-4:2002 (8)

DIN EN 13631-5 12.02 Explosives for civil uses - High explosives - Part 5: Determionation of resistanceto water; German version EN 13631-5:2002 (7)

DIN EN 13631-6 12.02 Explosives for civil uses - High explosives - Part 6: Determionation of resistanceto hydrostatic pressure; German version EN 13631-6:2002 (7)

DIN EN 13631-7 02.04 Explosives for civil uses - High explosives - Part 7: Determionation of safety andreliability at extreme temperatures; German version EN 13631-7:2003 (7)

DIN EN 13631-10 02.04 Explosives for civil uses - High explosives - Part 10: Method for the verificationof the means of initiation; German version EN 13631-10:2003 (8)

DIN EN 13631-11 02.04 Explosives for civil uses - High explosives - Part 11: Determionation of transmission of detonation; German version EN 13631-11:2003 (8)

DIN EN 13631-12 02.05 Explosives for civil uses - High explosives - Part 12: Specification of boosterswith different initiating capability; German version EN 13631-12:2004 (6)

DIN EN 13631-13 07.03 Explosives for civil uses - High explosives - Part 13: Determionation of density;German version EN 13631-13:2003 (7)

DIN EN 13631-14 07.03 Explosives for civil uses - High explosives - Part 14: Determionation of velocityof detonation; German version EN 13631-14:2003 (8)

DIN EN 13631-15 07.05 Explosives for civil uses - High explosives - Part 15: Calculation of thermodynamic properties; German version prEN 13631-15:2003 (12)

DIN EN 13631-16 11.04 Explosives for civil uses - High explosives - Part 16: Detection andmeasurement of toxic gases; German version EN 13631-16:2004 (7)

DIN 20163 11.94 Blasting - Terminology, units and symbols (14)DIN 20164-1 01.07 Blasting supplies - Explosives - Part 1: Requirements, testing, marking (12)

NA 008-07-04-02 AK Detonating cords

DIN EN 13630-1 03.04 Explosives for civil uses - Detonating cords and safety fuses - Part 1:Requirements; German version EN 13630-1:2003 (7)

DIN EN 13630-2 12.02 Explosives for civil uses - Detonating cords and safety fuses - Part 2:Determination of thermal stability of detonating cords and safety fuses; Germanversion EN 13630-2:2002 (7)

DIN EN 13630-3 12.02 Explosives for civil uses - Detonating cords and safety fuses - Part 3:Determination of sensitiveness to friction of the core of detonating cords;German version EN 13630-3:2002 (6)

DIN EN 13630-4 12.02 Explosives for civil uses - Detonating cords and safety fuses - Part 4:Determination of sensitiveness to impact of detonating cords; German versionEN 13630-4:2002 (8)

DIN EN 13630-5 03.04 Explosives for civil uses - Detonating cords and safety fuses - Part 5:Determination of resistance to abrasion of detopnating cords; German versionEN 13630-5:2003 (9)

DIN EN 13630-6 12.02 Explosives for civil uses - Detonating cords and safety fuses - Part 6:Determination of resistance to tension of detonating cords; German version EN13630-6:2002 (6)

DIN EN 13630-7 12.02 Explosives for civil uses - Detonating cords and safety fuses - Part 7:Determination of reability of initiation of detonating cords; German version EN13630-7:2002 (6)

DIN EN 13630-8 12.02 Explosives for civil uses - Detonating cords and safety fuses - Part 8:Determination of resistance to water of detonating cords and safety fuses;German version EN 13630-8:2002 (7)



26/45


DIN EN 13630-9 07.04 Explosives for civil uses - Detonating cords and safety fuses - Part 9:Determination of transmission of detonation from detonating cord to detonatingcord; German version EN 13630-9:2004 (7)

DIN EN 13630-10 08.05 Explosives for civil uses - Detonating cords and safety fuses - Part 10:Determination of initiating capacity of detonating cords; German version EN1360-10:2005 (8)

DIN EN 13630-11 12.02 Explosives for civil uses - Detonating cords and safety fuses - Part 11:

Determination of velocity of detonation of detonating cords; German version EN13630-11:2002 (6)DIN EN 13630-12 12.02 Explosives for civil uses - Detonating cords and safety fuses - Part 12:

Determination of burning duration of safety fuses, German version EN 13630-12:2002 (6)

DIN 20165 08.10 Blasting supplies - Intrinsically safe detonators (permitted detonators) -Requirements and testing (8)

NA 008-07-05 AA Plastics

DIN 22100-1 07.09 Articles and materials from synthetics for use in underground mines - Part 1:Conveyor belts - Hygienic requirements, testing, marking (8)

DIN 22100-3 10.10 Articles and materials from synthetic for use in underground mines - Part 3:Spiral air ducts - Safety requirements, testing, marking (8)DIN 22100-4 10.10 Articles and materials from synthetic for use in underground mines - Part 4: Flat

air ducts - Safety requirements, testing, marking (6)DIN 22100-5 10.10 Articles and materials from synthetic for use in underground mines - Part 5:

Tubes, tube isolations and hoses - Safety requirements, testing, marking (8)DIN 22100-6 10.10 Articles and materials from synthetic for use in underground mines - Part 6:

Sheeting, coated/uncoated tissue, brattice materials and lagging mats - Safetyrequirements, testing, marking (7)

DIN 22100-7 06.00 Articles and materials from synthetics for use in underground mines - Part 7:Safety requirements, testing, marking (17)

DIN 22100-7 08.10 Synthetic materials for use in underground mines - Part 7: Safety requirements,testing, marking (24)E

DIN 22118 08.91 Conveyor belts with textile plies for use in coal mining; fire testing (6)



27/45

FB Analysis of Raw Material/Coal preparation 0Register of Mining Standards 2010-12

08 Analysi s of Raw Material/Coal preparation

NA 008-08-01 AA Investigations of r aw material/Preparation of hard coal

DIN 22005-1 09.97 Investigations of raw material in hard-coal-mining - Part 1: Survey (8)DIN 22005-2 09.97 Investigations of the raw material in hard-coal-mining - Part 2: Terms relating to

raw material (13)DIN 22013 08.85 Investigations of the raw material in hard-coal-mining - Channel sample -

Sampling and schema of tests (9)DIN 22014 08.85 Investigations of the raw material in hard-coal mining - Raw coal sample from

the production of a working area - Sampling and schema of tests (10)DIN 22017 03.08 Investigations of the raw material in hard-coal-mining - Froth-flotation-analysis

(12)DIN 22018 01.85 Investigations of the raw material in hard-coal-mining determation of the particle-

density-distribution by float-and-sink-analysis (10)DIN 22019-1 03.85 Investigations of the raw material in hard-coal-mining; determination of the

particle-size-distribution 20 m by sieve-analysis (12)

DIN 22019-2 03.85 Investigations of the raw material in hard-coal-mining - Determination of theparticle-size-distribution - Part 1: Particle-size-distribution < 60 m by ultrasonic-microsieve-analysis (7)

DIN 22020-1 08.98 Investigations of raw material in hard-coal-mining - Microscopical examination of hard coal, coke and briquettes - Part 1: Terms, survey of processes and theirapplications (7)

DIN 22020-2 08.98 Investigations of raw material in hard-coal-mining - Microscopical examination of hard coal, coke and briquettes - Part 2: Preparation of polished surface fromlump material and particulate blocks (5)

DIN 22020-3 08.98 Investigations of raw material in hard-coal-mining - Microscopical examination of hard coal, coke and briquettes - Part 3: Maceral analysis on particulated blocks(5)

DIN 22020-4 12.98 Investigations of raw material in hard-coal-mining - Microscopical examination of hard coal, coke and briquettes - Part 4: Microlithotype analysis on particulateblocks (6)

DIN 22020-5 02.05 Investigations of the raw material in hard-coal-mining - Microscopicalexaminations of hard coal, coke and briquettes - Part 5: Reflectancemeasurements on vitrinites (12)

BB 22020-7 09.74 Mikroskopische Untersuchungen an Steinkohlen, Koksen und Briketts -Sonderuntersuchungen (4)

DIN 22021 07.85 Investigations of the raw material in hard-coalmining - Microscopicalexaminations of rocks (17)

DIN 22024 02.89 Investigations of the raw material in hard-coal-mining - Determination of tensilestrength on solid rock (5)

DIN 23004-1 01.87 Preparation of hard coal - Part 1: Survey (6)DIN 23004-2 05.88 Preparation of hard coal - Part 2: Terms relating to processes (15)DIN 23005 12.88 Preparation of hard coal - Description and estimation of raw coal properties in

view of preparation (10)DIN 23006-1 01.05 Preparation of hard coal - Assessment of preparation equipment and

processes - Part 1: General rules, balance of quantities (15)DIN 23006-2 01.05 Preparation of hard coal - Assessment of preparation equipment and

processes - Part 2: Sizing (14)DIN 23006-3 01.05 Preparation of hard coal - Assessment of preparation equipment and

processes - Part 3: Cleaning (13)DIN 23006-4 01.05 Preparation of hard coal - Assessment of preparation equipment and

processes - Part 4: Separation of solids from water (12)



28/45

FB Analysis of Raw Material/Coal preparation 0Register of Mining Standards 2010-12

DIN 23006-5 01.05 Preparation of hard coal - Assessment of preparation equipment andprocesses - Part 5: Size reduction and dissociation (9)

DIN 23006-6 01.05 Preparation of hard coal - Assessment of preparation equipment andprocesses - Part 6: Homogenizing (11)

DIN 23006-7 01.05 Preparation of hard coal - Assessment of preparation equipment andprocesses - Part 7: Involuntary breakage (8)

DIN 23007 10.05 Preparation of hard coal - Flocculants for process water - Terms, requirements,verification (12)

DIN 23008 05.88 Preparation of hard coal - Flotation agents - Terms, requirements, verification (8)DIN 23009 03.90 Preparation of hard coal - Medium solids - Terms, requirements, testing (9)DIN 23010-1 08.85 Preparation of hard coal - Simulation of processes and material-flows - Part 1:

Homogenizing (7)DIN 23010-2 12.88 Preparation of hard coal - Simulation of processes and material-flows - Part 2:

Separations (8)DIN 23011-2 02.89 Preparation of hard coal; preparation plants - Part 2: Flowsheets (10)DIN 23011-3 10.92 Preparation of hard coal; preparation-plants - Part 3: Graphical symbols for

flowsheets (14)

DIN 23011-4 11.06 Preparation of hard coal; preparation plants Part 4: Technical agreements withregard to the fixation of guaranties (7)

DIN 23011-5 11.06 Preparation of hard coal - Preparation plants - Part 5: Process control (9)DIN 23011-6 12.04 Preparation of hard coal - Preparation plants - Part 6: Equipment and operation

of a plant laboratory (9)DIN 23011-7 11.06 Preparation of hard coal - Preparation plants - Part 7: Equipment monitoring (7)DIN 23011-7 Bbl 1 12.09 Preparation of hard coal - Preparation plants - Part 7: Equipment monitoring;

Supplement 1: Means of application for the standard (7)DIN 23011-8 02.08 Preparation of hard coal - Preparation plants - Part 8: Process technical

requirements on preparation equipment (13)



29/45

FB Cokery, Briquettes 09Register of Mining Standards 2010-12

09 Cokery, Br iquettes

NA 008-09-01 AA Bricks for coke ovens

DIN 1089-1 02.95 Refractories for use in coke ovens - Part 1: Silica bricks - Requirements andtesting (6)

DIN 1089-2 02.95 Refractories for use in coke ovens - Part 2: Fireclay bricks - Requirements andtesting (7)

DIN 1089-3 10.90 Refractories for use in coke ovens; mortar for silica and fireclay bricks;requirements and testing (7)



30/45

FB Open Cast Mining 10Register of Mining Standards 2010-12

10 Open Cast Mining

NA 008-10-01 AA Excavators, spreaders and auxiliary equipment in opencast lignite mines

DIN 5651 11.79 Brake block holders and brake block keys for composite brake blocks on railvehicles; technical specifications (4) /FABERG co-author/

DIN 22261-1 12.04 Excavators, spreaders and auxiliary equipment in opencast lignite mines - Part1: Construction, commissioning and monitoring (10)

DIN 22261-1 01.10 Excavators, spreaders and auxiliary equipment in opencast lignite mines - Part1: Construction, commissioning and monitoring (10)

E

DIN 22261-2 12.06 Excavators, spreaders and auxiliary equipment in opencast lignite mines - Part2: Calculation principles (32)

DIN 22261-3 11.06 Excavators, spreaders and auxiliary equipment in opencast lignite mines - Part3: Welded connections, joint types, classification, test instruction (14)

DIN 22261-4 12.07 Excavators, spreaders and auxiliary equipment in opencast lignite mines - Part4: Hoisting winch brakes (6)

DIN 22261-5 12.07 Excavators, spreaders and auxiliary equipment in opencast lignite mines - Part5: Slewing brakes and overload protecting devices (7)

DIN 22261-6 12.07 Excavators, spreaders and auxiliary equipment in opencast lignite mines - Part6: Examination of ropes and rope end fittings (7)

DIN 43120 09.52 Electric railway vehicles; bow slipper holder for contact wire clamps (4)/FABERG co-author/

DIN 43139 12.67 Drums for contact-wires for electric traction (4) /FABERG co-author/DIN 43153 01.68 Thimble with clevis for overhead equipment (4) /FABERG co-author/DIN 43160 01.68 Eye and clevis for overhead equipment; connecting dimensions (4) /FABERG

co-author/

NA 008-10-02 AA Belt conveyors in opencast lignite mining

DIN EN 14658 06.10 Continuous handling equipment and systems - General safety requirements forcontinuous handling equipment for opencast lignite mining; German version EN14658:2005+A1:2010 (15)



31/45

FB Mine Plans 11Register of Mining Standards 2010-12

11 Mine Plans

NA 008-11-01 AA Mine surveying

DIN 18723-7 07.90 Field procedure for precision testing of surveying instruments - Part 7:Gyroscopes

DIN 21961 06.00 Mine surveying - Slip-on pivots, slip-on caps for suspension theodolites -Connecting dimensions (5)

NA 008-11-01-01 AK Basic s

DIN 21901 02.84 Mine plans; structure and list of standards; general principles (5)DIN 21901 Bbl 1 09.06 Mine plans - Structure and list of standards -Supplement 1: Contents (6)DIN 21901 Bbl 2 09.06 Mine plans - Structure and list of standards - Supplement 2: List of

abbreviations (18)DIN 21901 Bbl 3 07.02 Mine plans; structure and list of standards; indexDIN 21901-2 11.94 Mine plans - Structure and list of standards - Part 2: Interface for EDP based

transfer of symbols of mining - Specific mapping (12)

DIN 21902 10.99 Mine plants - Structure of mining specific plans (7)DIN 21902-2 08.08 Mine plants - Structure of mining specific plans - Part 2: Completion of mine

plans (11)DIN 21903 10.95 Mine plans - Sizes and foldings (8)DIN 21904 01.94 Mine plants; lettering (5)DIN 21905 11.93 Mine plants; drawing principles (5)DIN 21906 08.90 Mine plans - Subdivision of sheets (9)DIN 21906 Bbl 1 11.91 Mine plans; subdivision of sheets; survey (19)DIN 21906 Bbl 2 01.94 Mine plans; subdivision of sheets; survey (14)

DIN 21907 04.03 Mine plans - Graphic design of sheets (12)DIN 21908 01.94 Mine plans - Colours (8)

NA 008-11-01-02 AK Objects on the surf ace, open pit mines

DIN 21909 02.02 Mine plans - Survey points and lines (9)DIN 21910 06.02 Mine plans - Titles and boundaries (12)DIN 21911 03.08 Mine plans; objects on the surface and contour lines (12)DIN 21912-1 01.06 Mine plans - Opencast mining - Part 1: General requirements (12)DIN 21912-2 03.01 Mine plans - Open cast mining - Part 2: Reconstruction (8)DIN 21912-2 11.09 Mine plans - Open cast mining - Part 2: Reconstruction (11)E

NA 008-11-01-03 AK Geologic symbols and terms

DIN 21918-1 10.99 Mine plans - Mineral deposits - Part 1: Terms, classification (6)DIN 21918-2 08.04 Mine plans - Mineral deposits - Part 2: Thicknesses (10)DIN 21919-1 01.00 Mine plans - Stratigraphy - Part 1: General classification (7)DIN 21919-2 12.08 Mine plans - Stratigraphy - Part 2: Regional and local subdivisions; Hard coal (8)DIN 21919-3 11.01 Mine plans - Stratigraphy - Part 3: Regional and local subdivisions; Lignite (9)DIN 21920-1 11.88 Mine plans - Petrography - Part 1: Generally applicable symbols - Sediments (9)DIN 21920-2 04.96 Mine plans - Petrography - Part 2: Magmatites (10)

DIN 21920-3 04.96 Mine plans - Petrography - Part 3: Metamorphic and other lithogeneticphenomena (10)DIN 21920-4 04.96 Mine plans - Petrography - Part 4: Minerals (6)



32/45

FB Mine Plans 11Register of Mining Standards 2010-12

DIN 21920-5 11.94 Mine plans - Petrography - Part 5: Hard coal mining (12)DIN 21920-7 04.96 Mine plans - Petrography - Part 7: Potash and rock salt mining (7)DIN 21921 04.96 Mine plans - Tectonic elements and figure of strata (13)DIN 22011 11.93 Investigations of the raw material in hard-coal-mining - Treatment of exploratory

drillings (17)DIN 22012 01.94 Investigations of the raw material in hard-coal-mining - Macropetrographic

classification and topographic survey of hard-coal and host rock (8)DIN 22015 10.93 Investigations of the raw material in hardcoal-mining - Macroscopicclassification and description of overburden rock (9)

NA 008-11-01-04 AK Special representations

DIN 21913-11 01.00 Mine plans - Deep mining - Part 11: Geometrical dimensions in undergroundworkings (7)

DIN 21916-1 02.07 Mine plans - Operational safety - Part 1: Ventilation system and meteorology (13DIN 21916-2 02.10 Mine plans - Operational safety - Part 2: Fire prevention on the surface (12)DIN 21916-3 06.93 Mine plans; operational safety; fire prevention under the surface (10)

DIN 21916-3 11.09 Mine plans - Operational safety - Part 3: Fire prevention under the surface (11)E DIN 21917 02.99 Mine plans - Strata and ground movements (13)DIN 21917-2 03.02 Mine plans - Strata and ground movements - Part 2: Geomechanical measuring

points (7)

NA 008-11-01-05 AK Mine workings

DIN 21913-1 02.92 Mine plans; deep mining; underground workings (19)DIN 21913-1 Bbl 1 02.92 Mine plans; underground working; storage and final deposition in mine workings

(33)DIN 21913-2 02.09 Mine plans - Deep mining - Part 2: Extraction, stowage and deposit (14)

DIN 21913-3 02.08 Mine plans - Deep mining - Part 3: Closure of underground workings (8)DIN 21913-4 02.09 Mine plans; deep mining; Part 4: hazardous zones, zones of protectivemeasures (11)

DIN 21913-6 07.04 Mine plans - Deep mining - Part 6: Safekeeping of mining produced hollows (7)DIN 21913-7 11.10 Mine plans - Deep mining - Part 7: Shaft plan (11)E

NA 008-11-01-06 AK Dri lli ng, caverns, s torage, final deposit ion

DIN 21914-1 10.05 Mine plans - Drilling and cavern - Part 1: Drilling (15)DIN 21914-2 02.99 Mine plans - Drilling and cavern - Part 2: Brine caverns (10)



33/45

FB Fuels 12Register of Mining Standards 2010-12

12 Fuels

NA 008-12-01 AA Gaseous fuels

DIN 1340 12.90 Gaseous fuels and other gases - Types, constituents, application (7) /FABERGco-author/

DIN 1340 Bbl 1 12.90 Gaseous fuels and other gases - Types, constituents, application - Remarks onthe production (5) /FABERG co-author/

DIN 1871 05.99 Road marking materials - Physical properties; German version EN 1871:2000(13) /FABERG co-author/

DIN EN 1918-1 07.98 Gas supply systems - Underground gas storage - Part 1: Functionalrecommendations for storage in aquifers; German version EN 1918-1:1998 (9)/FABERG co-author/

DIN EN 1918-2 07.98 Gas supply systems - Unterground gas storage - Part 2: Functionalrecommendations for storage in oil and gas fields; German version EN 1918-2:1998 (8) /FABERG co-author/

DIN EN 1918-3 07.98 Gas supply systems - Underground gas storage - Part 3: Functionalrecommendations for storage in solution-mined salt cavities; German version

EN 1918-3:1998 (10) /FABERG co-author/DIN EN 1918-4 07.98 Gas supply systems - Underground gas storage - Part 4: Functional

recommendations for storage in rock caverns; German version EN 1918-4:1998 (7) /FABERG co-author/

DIN EN 1918-5 07.98 Gas supply systems - Underground gas storage - Part 5: Functionalrecommendations for surface facilities; German version EN 1918-5:1998 (6)/FABERG co-author/

DIN ISO 5275 10.05 Petroleum products and hydrocarbon solvents - Detection of thiols and othersulfur species - Doctor test (ISO 5275:2003) (6) /FABERG co-author/

DIN EN ISO 6141 11.06 Gas analysis - Requirements for certificates for calibration gases and gasmixtures (ISO 6141:2000); German version EN ISO 6141:2006 (8) /FABERG co -author/

DIN ISO 6142 05.85 Gas analysis - Preparation of calibration gas mixtures - Weighing methods (7)/FABERG co-author/

DIN EN ISO 6143 11.06 Gas analysis - Comparison methods for determining and checking thecomposition of calibration gas mixtures (ISO 6143:2001); German version ENISO 6143:2006 (15) /FABERG co-author/

DIN ISO 6144 05.85 Gas analysis; preparation of calibration gas mixtures; static volumetric methods(10) /FABERG co-author/

DIN ISO 6146 04.83 Gas analysis; preparation of calibration gas mixtures; manometric method (12)/FABERG co-author/

DIN EN ISO 6326-3 04.98 Natural gas - Determination of sulfur compounds - Part 3: Determination of

hydrogen sulfide, mercaptan sulfur and carbonyl sulfide sulfur by potentiometry(ISO 6326-3:1989); German version EN ISO 6326-3:1997 (7) /FABERG co-author/

DIN EN ISO 6326-5 04.98 Natural gas - Determination of sulfur compounds - Part 5: Lingener combustionmethod (ISO 6326-5:1989); German version EN ISO 6326-5:1997 (9)/FABERG co-author/

DIN EN ISO 6570 12.04 Natural gas - Determination of potential hydrocarbon liquid content - Gravimetricmethods (ISO 6570:2001); English version EN ISO 6570:2004 (13) /FABERGco-author/

DIN EN ISO 6974-1 06.02 Natural gas - Determination of composition with defined uncertainty by gaschromatography - Part 1: Guidelines for tailored analysis (ISO 6974-1:2000);German version EN ISO 6974-1:2001 (12) /FABERG co-author/

DIN EN ISO 6974-1 03.10 Natural gas - Determination of composition and associated uncertainty by gaschromatography - Part 1: General guidelines and calculation of composition(ISO/DIS 6974-1:2010); German version prEN ISO 6974-1:2010 (20) /FABERGco-author/

E



34/45

FB Fuels 12Register of Mining Standards 2010-12

DIN EN ISO 6974-2 07.02 Natural gas - Determination of composition with defined uncertainty by gaschromatography - Part 2: Measuring- system characteristics and statistics forprocessing of data (ISO 6974-2:2001); German version EN ISO 6974-2:2002 /Note: Applies only in conjunction with DIN ISO 6974-1 (2002- 06) (13) /FABERGco-author/

DIN EN ISO 6974-2 03.10 Natural gas - Determination of composition and associated uncertainty by gaschromatography - Part 2:Uncertainty calculations (ISO/DIS 6974-1:2010);German version prEN ISO 6974-2:2010 (20) /FABERG co-author/

E

DIN EN ISO 6974-3 06.02 Natural gas - Determination of composition with defined uncertainty by gaschromatography - Part 3: Determination of hydrogen, helium, oxygen, nitrogen,carbon dioxide and hydrocarbons up to C8 using two packed columns (ISO6974-3:2000); German version EN ISO 6974-3:2001 / Note: Applies only inconjunction with DIN EN ISO 6974-1 and DIN EN ISO 6974-2 (11) /FABERGco-author/

DIN EN ISO 6974-4 06.02 Natural gas - Determination of composition with defined uncertainty by gaschromatography - Part 4: Determination of nitrogen, carbon dioxide and C1- toC5- and C6+hydrocarbons for a laboratory and on-line measuring systemusing two columns (ISO 6974-4:2000); German version EN ISO 6974-4:2001 /Note: Applies only in conjunction with DIN EN ISO 6974-1 and DIN EN ISO6974-2 (10) /FABERG co-author/

DIN EN ISO 6974-5 06.02 Natural gas - Determination of composition with defined uncertainty by gaschromatography - Part 5: Determination of nitrogen, carbon dioxide and C1- toC5- and C6+hydrocarbons for a laboratory and on-line measuring systemusing two columns (ISO 6974-5:2000); German version EN ISO 6974-5:2001(11) /FABERG co-author/

DIN EN ISO 6974-6 08.05 Natural gas - Determination of composition with defined uncertainty by gaschromatography - Part 6: Determination of hydrogen, helium, oxygen, nitrogen,carbon dioxide and C1 to C8 hydrocarbons using three capillary columns (ISO6974-6:2002); German version EN ISO 6974-6:2005 (12) /FABERG co-author/

DIN EN ISO 6975 09.05 Natural gas - Extended analysis - Gas-chromatographic method (ISO6975:1997); German version EN ISO 6975:2005 (14) /FABERG co-author/

DIN EN ISO 6975/B1 09.08 Natural gas - Extended analysis - Gas-chromatographic method (ISO6975:1997); German version EN ISO 6975:2005, Corrigendum to DIN EN ISO6975:2005-09 (99) /FABERG co-au

DIN Standard for Mining.pdf

Documents

Transcript of DIN Standard for Mining.pdf