Dimensions and Weights Gator
Transcript of Dimensions and Weights Gator
GatorHydraulic Control Valves
Gator Valves are weir type single chamber control valves. Designed with simplicity inmind and not compromising on operational versatility.
Tried and tested mechanical materials and engineering design concepts have beenintroduced into the product, making it both durable and reliable in performance.
This range of valves can be used in typical industrial, waterworks and irrigationapplications.
Available in several configurations and end connections
Sound hydraulic performance with improved flow dynamics resulting in a quiet and smoothwater flow during operation
Minimum head loss and low pressure required to operate the valve
Manufactured from durable and rugged raw materials along with minimal moving parts, provides years of reliable service
Versatile and adaptable for almost any operating application
Numerous operating functions such as: Manual, Electrical, Pressure Reducing, PressureSustaining, Remote Control as well as numerous other control combinations
Suitable to handle various types of different liquids including, slurries and abrasive liquids
W Series
F e a t u r e s
Our policy is one of continued research and development in the quest to improve our products. We therefore reserve the rights to amend information provided in this document without providing notice.
L
H
R
* Height with mechanical throttle fully opened
Valve SizeLength in mm
(in inches)Height in mm
(in inches)Ht* in mm(in inches)
Width in mm(in inches)
Radius in mm(in inches)
Weight in Kg(in pounds)
DN 50 (2.0”)139
(5.47)150
(5.91)190
(7.48)127(5.0)44
(1.73)3.2
(7.05)
DN 65 (2.5”)175
(6.89)186
(7.32)225
(8.86)145
(5.71)59
(2.32)6.2
(13.67)
DN 80/65/80 (3/2.5/3”)
175(6.89)186
(7.32)225
(8.86)145
(5.71)59
(2.32)5.6
(12.35)
DN 80 (3”)205
(8.07)210
(8.27)300
(11.81)190
(7.48)65
(2.56)9.8
(21.61)
* Height with mechanical throttle fully opened
L
RH
Valve SizeLength in mm
(in inches)Height in mm
(in inches)Ht* in mm(in inches)
Width in mm(in inches)
Radius in mm(in inches)
Weight in Kg(in pounds)
DN 80 (3.0”)242
(9.53)202
(7.95)342
(13.46)203
(7.99)102
(4.01)13.2
(29.10)
DN 100 (4.0”)315
(12.4)243
(9.21)383
(15.08)228
(8.98)114
(4.49)20.6
(45.42)
DN 150 (6.0”)403
(15.87)331
(13.03)
305(12)153
(6.02)46.6
(102.74)
DN 200/150/200
(8/6/8”)411
(16.18)390
(15.35)
370(14.56)
185(7.28)63.0
(138.89)
* Height with mechanical throttle fully opened
L
R
H
H o w t o O r d e rExample: VGVEBA5A Is a complete DN 50 epoxy coated threaded BSP angle valve (for the correct ordering codes on control options such as manual override, electric control, etc. contact your dealer)
VGroupV - Valves
GSub-GroupG - Gator Valves
VComponentB - Body onlyC - Valve Cap onlyD - DiaphragmO - OptionsP - Spare PartsS - ServicesV - Valve complete
ECoating TypeZ - No CoatingE - Epoxy Powder Coated
BConfig. & MaterialA - Inline Cast IronB - Angle Cast IronZ - Not Applicable
AEnd Connection TypeA -Threaded Fem. BSPB - Threaded Fem. NPTF - Flanged BS 10 Table DE - Flanged BS 10 Table EG - Flanged BS 10 Table FH - Flanged ISO PN 10I - Flanged ISO PN 16K - Flanged ANSI 125L - Flanged ANSI 150Z - Not Applicable
5Size0 - DN 200/150 (8/6”)1 - DN 100 (4”)2 - DN 150 (6”)3 - DN 25 (1”)4 - DN 40 (1.5”)5 - DN 50 (2”)6 - DN 65 (2.5”)7 - DN 80/65 (3 / 2.5”)8 - DN 80 (3”)
ADiaphragm Spec.A - Natural Rubber 16 Bar
D i m e n s i o n s a n d W e i g h t s
Valve SizeLength in mm
(in inches)Height in mm
(in inches)Ht* in mm(in inches)
Width in mm(in inches)
Radius in mm(in inches)
Weight in Kg(in pounds)
DN 40 (1.5”)145(5.7)103
(4.05)188
(7.04)109(4.3)38
(1.5)2.0
(4.41)
DN 50 (2.0”)169
(6.65)117(4.6)202
(7.95)127(5.0)44
(1.73)3.4
(7.50)
DN 65 (2.5”)230
(9.05)154
(6.06)239
(9.41)145
(5.71)59
(2.32)6.2
(13.67)
DN 80/65/80 (3/2.5/3”)
230(9.05)154
(6.06)239
(9.41)145
(5.71)59
(2.32)5.4
(11.90)
DN 80 (3.0”)280
(11.02)169
(6.65)309
(12.17)190
(7.48)65
(2.56)8.8
(17.64)
DN 25 (1.0”)
82
165
76
23
(4.37)
(3.23)
(2.2)
111
1.0
(6.5)
(0.91)
(2.99)
Not Applicable Not Applicable
Kimberley (Satellite Office)É +27 (53) 004 0288
Nelspruit (Regional Office)É +27 (13) 004 0285
Gauteng (Regional Office)É +27 (12) 804 7360
Western Cape (Head Office)É +27 (21) 982 7561
ü WWW.IRRIGATORPRODUCTS.COMš [email protected]
GatorIrri
Gator Valves operate using the available pressure within the pipeline or an external pressuresupply of air or water, provided this pressure is equal to or greater than the pressure withinthe pipeline in which the control valve is installed.
To close the valve, water or air pressure is induced into theupper chamber forcing the diaphragm to close against theweir within the valve and thereby stopping the flow of theliquid or gas within the pipeline.
To open the valve, the water or air trapped within the upperchamber is released into atmosphere or into the downstreamof the valve, through the pipeline.
By incorporating other control mechanisms, such as a pilotvalve, the valve can be adapted to regulate flow andpressure without being fully closed or fully open.The valves diaphragm is the only moving part and is assistedto close under all pressures with the aid of a spring.
P r o d u c t O p e r a t i o n
CLOSED
A c c e s s o r i e s
OPEN
Flanged Inline Valves
DN
100
DN
80
O p e r a t i n g P a r a m e t e r s
Minimum Opening Pressure
Maximum Operating Pressure
Maximum Operating Temperature (H2O)
Recommended Maximum Pressure Reduction Ratio
Recommended Flow Velocity Parameters
Maximum Recommended Flow Velocity
0.7 Kg/cm²
16 Kg/cm²
70 Degrees Celsius
3 : 1
from 0.5 m/sec. up to 5 m/sec.
15 m/sec. for a maximum of 60 seconds
M a t e r i a l s
Body and Bonnet
Diaphragm
Spring
Spring Retainer Disk
Nuts and Washers
Coatings
Cast Iron
Reinforced Natural Rubber
Stainless Steel
Glass Reinforced Nylon
Stainless Steel
Fusion Bonded Polyester Powder Coated
G e n e r a l S p e c i f i c a t i o n s
End Connections
Control Ports
Mechanical ThrottleMounting Port
Threaded Connections - Female ISO (BSP) and ANSI (NPT)
Flanged Connections - BS 10 Table D or BS 4504 - 10 (Other flange configurations can be supplied on request. However non standard specifications will cause delay in delivery time.)
Upstream on Valve Body - ¼” Threaded Female BSP
Downstream on Valve Body - ¼” Threaded Female BSP
Offset on Valve Bonnet - ¼” Threaded Female BSP
Center on Valve Bonnet - ¼” Threaded Female BSP on DN 25, 40, 50, 65, 80, 80/65/80 Valves
Center on Valve Bonnet - ½”Threaded Female BSP on DN 80,100,150 & 200/150/200 Valves
H e a d L o s s C h a r t s
Brass Pilot Valves
In 2 and 3 way format
Suitable for operating pressures up to 16 Kg/m²
With set pressures from 0.7 to 12 Kg/m²
For pressure reducing, pressure sustaining,
pressure relief and quick relief applications
Plastic Pilot Valves
3 way format
Suitable for operating pressures up to 10 Kg/m²
With set pressures from 0.7 to 7 Kg/m²
For pressure reducing, pressure sustaining,
pressure relief and quick relief applications
Solenoid Valves & Operators
In 2 and 3 way format
Available in AC and DC
Suitable for operating pressures up to 16 Kg/m²
In Normally Open and Normally Closed Versions
Other Accessories
A full range of plastic and brass fittings in all sizes
A full range of brass 3 Way and 2 Way Ball Valves
A full range of brass and plastic finger filters
Mechanical Throttles for all valves except DN 150
and DN 200/150 sizes
Threaded Inline Valves
DN
40
Threaded Inline & Angle Valves
DN
50
DN
80
DN
80/
65/8
0
Head L
oss
- K
g/c
m²
0
0,1
0,2
0,3
0,4
0,5
0,6
0,7
0
0,1
0,5
Head L
oss
- K
g/c
m²
0,2
0,3
0,4
0,6
0,7
DN
25
DN
65
DN
150
; D
N 2
00/1
50
Rate of Flow - m³/hr
2 4 6 8 10 12 14 16 18 20 22 24 26 10 20 30 40 50 60 70 80 90 100
Rate of Flow - m³/hr Rate of Flow - m³/hr
50 100 150 200 250 300 350 400 450
Head L
oss
- K
g/c
m²
0
0,1
0,2
0,3
0,4
0,5
0,6
0,7