Digital Technique Mrs. Sunita M Dol, CSE Dept

Walchand Institute of Technology, Solapur Page 1

HANDOUT#9

AIM:

Implement Boolean expression using 8:1 multiplexer

f1 = ∑ m (2, 3, 6, 7)

f2 = ∏ M (2, 3, 5, 7)

LEARNING OBJECTIVES:

- Implement the Boolean expression in SOP and POS form using 8:1

multiplexer.

COMPONENT REQUIRED:

- Logic gates (IC) trainer kit.

- Connecting patch chords.

- IC 74151

Sr. No. Component Specification

1 8:1 mux IC74151

THEORY:

� Mutiplexer or data selector is the combinational circuit that gets one out of

several inputs to a single output.

� In multiplexer, the input selected is controlled by a set of select lines. For

selecting one out of n inputs for connection to the output, a set of m select

lines is required where 2m=n.

� Depending upon the digital code applied at select lines, one out of n data

sources is selected and transmitted to a single output channel.

� A strobe or enable input G is incorporated which helps in cascading and it is

generally active low which means it perform its intended operation when it

is low.

� IC 74151 Description

o IC 74151 is used as 8:1 mux. It is a 16 pin IC.

o Pin number 4, 3, 2, 1, 15, 14, 13, 12 acts as input signal from 0 to 7

respectively.

Digital Technique Mrs. Sunita M Dol, CSE Dept

Walchand Institute of Technology, Solapur Page 2

o Pin number 9, 10, 11 are the select inputs used to set an input.

o We get the output of this circuit at pin number 5. And its complement

on pin number 6.

o Pin number 7 acts as a strobe which is used for cascading purpose

otherwise it is connected to the ground.

o Pin number 16 is the power supply that is Vcc.

o The block diagram of IC 74151 is given in figure a and pin diagram of

IC 74151 is given in figure b.

Figure a: Block diagram

Digital Technique Mrs. Sunita M Dol, CSE Dept

Walchand Institute of Technology, Solapur Page 3

Figure b: Pin diagram

Truth table:

Select Input Output

Y S2 S1 S0

I0 0 0 0 0

I1 0 0 1 1

I2 0 1 0 2

I3 0 1 1 3

I4 1 0 0 4

I5 1 0 1 5

I6 1 1 0 6

I7 1 1 1 7

� The design procedure is given below:

o Identify the decimal number corresponding to the each minterm in the

expression. The input lines corresponding to these numbers are to be

connected to logic 0 level.

o All other input lines are to be connected to logic 0 level.

o The inputs are to be applied to the select lines.

Given Logic function:

Digital Technique Mrs. Sunita M Dol, CSE Dept

Walchand Institute of Technology, Solapur Page 4

f1 = ∑ m (2, 3, 6, 7)

In this example, connect the input lines 2, 3, 6, 7 to logic 1 and remaining to logic

0

Truth Table

Select Input Output

Y A B C

0 0 0 0

0 0 1 0

0 1 0 1

0 1 1 1

1 0 0 0

1 0 1 0

1 1 0 1

1 1 1 1

Digital Technique Mrs. Sunita M Dol, CSE Dept

Walchand Institute of Technology, Solapur Page 5

f2 = ∏ M (2, 3, 5, 7)

In this example, connect the input lines 2, 3, 5, 7 to logic 0 and remaining to logic

1

Truth Table

Select Input Output

Y A B C

0 0 0 1

0 0 1 1

0 1 0 0

0 1 1 0

1 0 0 1

1 0 1 0

1 1 0 1

Digital Technique Mrs. Sunita M Dol, CSE Dept

Walchand Institute of Technology, Solapur Page 6

1 1 1 0

PROCEDURE:

1. Check the components for their working.

2. Insert the appropriate IC into the IC base.

3. Make connections as shown in the circuit diagram.

4. Provide the input data via the input switches and observe the output on

output LEDs

5. Give various combinations of inputs and note down the output with help of

LED for all gate ICs one by one.

RESULT:

Thus we have implemented Boolean expression using 8:1 multiplexer

f1 = ∑ m (2, 3, 6, 7)

f2 = ∏ M (2, 3, 5, 7)