DIGITAL PROCESSOR ENHANCED 3 (DPE3)

DIGITAL PROCESSORENHANCED – 3 (DPE3)

DPE3 SERIES

PRODUCT CATALOG

ANYWAVE

Introduction

Key Facts Promotional MUX (with Dummy Programs): Allows users to advertise “coming-soon” programming

by setting up and multiplexing into their current stream N number of Dummy Program commercials Enhanced SPF: allows users to upload their own still pictures, or streams. Each sub-program in the RF

channel can be configured to have its own unique SPF displayed with its valid PSIP information. HourlyID: Allows users to create/display custom hourly station identification. The time source can be

referenced from either STT (from the stream) or NTP. The user can also manually reset the time to the beginning of each day.

Enhanced EAS: Supports two EAS streams input over IP (so one can be the primary and the other one is the secondary, as a backup) from different IP/port. Supports multicast or unicast.

Input: Supports TSoIP and ASI inputs. PSIP generation: Supports manual entry of PSIP information and TSID for incoming streams. Output bit rate user configurable: Allows users to set output bit rates, helpful for ATSC1.0/3.0

compatibility. Enhanced GUI: System level block diagram showing overall status of the transmitter system.

The ANYWAVE Data Processor Enhanced 3 module is designed to keep any TV station on-air evenwith the loss of the transmitter input signal, to promote/advertise future “coming-soon” additionalchannels with “Dummy Program” commercials for future programing, to provide an hourly station IDnotification, to provide Emergency Alert Services as the main service or as a back up system, whilekeeping an eye on the future with an optional ATSC3.0 gateway upgrade combined with the Anywave5X+ Exciter to move to the new ATSC3.0 standard. DPE3 stands for “Data Processor with Enhancedfeatures”, Enhanced SPF/EAS/GUI, and more! The system is installed prior to the Anywave 5X+ exciter,or any other manufacturers exciter that has an ASI input. If connected to an Anywave Transmitter italso includes a simplified system schematic graphical user interface and display, to show the currentstatus of all key assemblies inside the transmitter.

• Easy to install• Easy to set up• Provides unique features for ALL broadcast stations• Installs prior to existing exciter (even OEM)

ANYWAVECOMMUNICATION TECHNOLOGIES

Applications Ideal for Repack with ATSC3.0 Gateway/Processor Hourly Station ID, and EAS implementation Never lose your viewing audience; always have your station on-air, even when your network

programming is lost Promote “coming soon” channels through Dummy Program commercials


1 2 3

6 5 4789

1

2

3

Power and Error LED’sReset System ButtonManagement PortAC Mains Input and switchCooling Fan10MHz Input Ref.Transport Streams Inputs and OutputsUSB PortManagement/Data Ports 1, 2 and 3

4

5

6

7

8

9

Features

General Overview

SPF The SPF function allows you to put

your logo and your message on every program in the even to of a complete loss of video and audio input, even if it is TSoIP or ASI. The display can be a static picture or a 1 minute video with audio. The static pictures or transport streams can be uploaded easily and remotely and no expensive software is required.


MUX The DPE-3 allows the

generation of dummy channels allowing you to promote future channels. Allows user to add up to 3 dummy programs into the input stream. User can manually enter information for dummy program(s), including program numbers, source ID, short names, major channel numbers, minor channel numbers

RECORD The DPE-3 allows the

user to record up to 1 minute of both input and output streams so that these may be easily analyzed. User can export streams in TS file format and save them in any local PC. This is very convenient for stations being fed via IP input and if the station encounters transport stream breakup and is not able to determine the location of the problem.

More Features

and PAT/PCR/Video/Audio PIDs. The temporary display allows the promotion of future programs on that channel, and ensures viewers do not have to rescan when the permanent new channel is available.


EAS Supports two EAS stream inputs

over IP, so that one can be the primary (EAS1) and the other one (EAS2) as a secondary or back up. Whenever any of the two EAS inputs are present, DPE3 switches to EAS signals automatically, and resumes to main signals only after both EAS signals have stopped. Keeps all PSIP information of the original main signals. Support Unicast and Multicast. Works with most EAS generators with IP outputs.

PSIP The DPE-3 provides an

inexpensive PSIP Generation system. It provides the option to either pass through or deliver a complete new set of PSIP data to all streams. A user can manually enter PSIP information, including short names, major channel numbers, minor channel numbers and TSID.

More Features

HOURLY ID The DPE-3

provides an inexpensive hourly station ID function for every program channel . Allows user to upload any still picture or stream with audio, to display on the screen at the beginning of every hour, or pre-set time after the hour. For different programs in one RF channel, users can have different displays with the appropriate valid PSIP information. Both offset time and duration are user configurable. Supports time synchronization either from NTP or STT.


More Features

parts of the transmitter and is identified by a GREEN is GOOD and RED IS BAD status. The left hand side of the screen are links to all the sub-device web pages for easy management. User can employ the settings section to set network sections for each sub-device.

Configuration (for ATSC1.0 and ATSC3.0)

GUI The DPE-3 provides an

enhanced Graphical User Interface for Anywave Transmitters. Ideal for non-technical operators. At the top of the screen it shows the power and RF performance. The center of the screen displays all the important


1. Encoding: I-Series (by ANYWAVE/Igolgi), EPG and Dash Encoder (by 3rd Party)• HVEC encoding into ATSC3.0 formats

2. ATSC3.0 Gateway & Data Processor:• Encapsulation into ATSC3.0 Baseband frame• Generation of STL output packets over IP (STLTP)• Single and Multiple PLP management• Automatic configuration for 5X+ Exciter• ATSC3.0 SFN Adaption• Validation of ATSC3.0 transmission parameters

3. Modulation: 5X+ Digital Exciter• ATSC3.0 modulation (OFDM)• Linear and non-linear correction error correction

4. Amplifier: SLATE/GRANITE/MAGMA Series• Hi-Efficiency Broadband RF amplifiers from 2W to 120kW

5. RF Output Components• Band Pass Filters, Channel combiners and Directional Couplers

6. Metering: SPM and ANY1022• RF Power Metering• RF Performance and Monitoring of ATSC/ATSC3.0

7. SFN: FLINT Series On Channel Digital Repeaters (Gap Fillers)• Antennas• Power Levels between 20W and 200W• Patented Echo Cancellation Technology

ATSC3.0 by ANYWAVE

• Complete Range of ATSC3.0 products• Full Support of ATSC3.0 standard• Easy Upgrade from ATSC1.0• Advanced and Cost-effective End to

End Solution


SpecificationsSignal Inputs

Transport Stream• DTV TS Inputs: 2 Transport Stream inputs DVB-ASI

Connector: BNC female 75 Ω

Signal OutputsTransport Stream• DTV TS Outputs: 2 Transport Stream outputs DVB-

ASI Connector: BNC female 75 Ω

External 10MHz• Input Level: AC coupled V (p-p) > 300 mV• Input Connector: BNC female 50 Ω

Data4 Inputs RJ45 connectors provide TSoIP input and Data Management• TSoIP / Native IP Transport inputs for ATSC 1.0

and ATSC3.0 interface• Data system 100/1000Base-T Ethernet

connectivity to the DPE3 to facilitate diagnostics, monitoring and system updates.

Power Supply• Power Supply: 88 ~ 264 VAC, 50/60Hz

Conditions• Operating Temperature: 0° C ~ 50° C

(+32°F~+122°F)• Operating Humidity: ≤ 95%

Weight and DimensionsSize: Height : 1 RU, 1.75” (44.5mm)Depth : 8.5” (215.9mm)Width : 19” Wide (482.6mm)Weight: 6 LBS (net) / 10 LBS (gross)

2.7Kg (net) / 4.55 Kg (gross)

Signal Processing ATSC3.0

Multiple PLP: 64 PLPPLP modulation: QPSK, 16QAM, 64QAM, 256QAM, 1024QAM, 4096QAM

PLP LDPC code rate: 2/15, 3/15, 4/15, 5/15, 6/15, 7/15, 8/15, 9/15, 10/15, 11/15, 12/15, 13/15FFT Size: 8K, 16K, 32K

Guard intervals (samples): 192, 384, 512, 768, 1024, 1536, 2048, 2432,3072, 3648, 4096 and 4864

Pilot pattern: SP3_2, SP3_4, SP4_2, SP4_4, SP6_2, SP6_4, SP8_2, SP8_4, SP12_2, SP12_4, SP16_2, SP16_4, SP24_2, SP24_2, SP32_2, SP32_4

Signaling FEC Type Modes 1 to 7 for L1-Basic and L1- Detail

Network modes: MFN & SFN

Test modes: Single carrier, PRBS, NULL-Bootstrap and OFDM PAPR 3

DPE3-05-20

www.anywavecom.net

We have your broadcast transmission needs covered

CostEffective

100%

Reliable100%

Scalable100%

Dependable100%

Anywave Communication TechnologiesEmail: [email protected]

Phone: +1 (847) 415 2258Fax: +1 (847) 415 2112

Address: 100 N Fairway Drive, Suite 128 Vernon Hills, IL 60061

Website: www.anywavecom.net

ANYWAVESpecification details subject to change without notice

DIGITAL PROCESSOR ENHANCED 3 (DPE3)

Documents

Transcript of DIGITAL PROCESSOR ENHANCED 3 (DPE3)