Diesel Gen Tips
-
Upload
roshan-shanmughan -
Category
Documents
-
view
217 -
download
0
Transcript of Diesel Gen Tips
8/19/2019 Diesel Gen Tips
http://slidepdf.com/reader/full/diesel-gen-tips 1/10
DIESEL GENERATORS
8/19/2019 Diesel Gen Tips
http://slidepdf.com/reader/full/diesel-gen-tips 2/10
Main Components of a Gen-set
•
Engine•Alternator
•Fuel system
•Voltage regulator
•Cooling system
•Exhaust system
•Lubrication system•Battery charger
•Control Panel
•Main Assembly / Frame
8/19/2019 Diesel Gen Tips
http://slidepdf.com/reader/full/diesel-gen-tips 3/10
8/19/2019 Diesel Gen Tips
http://slidepdf.com/reader/full/diesel-gen-tips 4/10
INSTALLATION GUIDELINES
•SITE PLANNING
•ROOM SIZE
•ENGINE COOLING SYSTEM
•ENGINE EXHAUST SYSTEM
•FUEL TANKS
•CONTROLS AND TRANSFER SWITCH
•GENSET NOISE
8/19/2019 Diesel Gen Tips
http://slidepdf.com/reader/full/diesel-gen-tips 5/10
ROOM LAYOUT
•IMPORTANCE OF ROOM LAYOUT
•SERVICEABILITY
•VENTILATION
•EASE IN OPERATION
•GENSET ROOM AESTHETICS
•FUTURE EXPANSION PLANS TO BE
CONSIDERED WHILE DECIDING ON
ROOM SIZE.
•OPENING / SHUTTERS TO BE
PROVIDED FOR GEN-SET PLACEMENT
8/19/2019 Diesel Gen Tips
http://slidepdf.com/reader/full/diesel-gen-tips 6/10
ROOM VENTILATION
•PROPER VENTILATION IS NECESSARY TO
•Provide clean and fresh combustion air •Remove heat enrgy dissipated by the gen-set
•IMPROPER VENTILATION CAN LEAD TO :
•Poor fuel efficiency
•Poor perfomance
•Failure of rubber components
•Higher room temperatures
•High temperature rise in gen-set windings
•For integral radiator cooled engine, discharge air to
be ducted
•
For heat exchanger cooled engine, forcedventilation is required
8/19/2019 Diesel Gen Tips
http://slidepdf.com/reader/full/diesel-gen-tips 7/10
•FOUNDATION
•Installation shouldn’t be on loose sand or clay
•
Foundation should be designed considering safe bearingcapacity of soil
•Length and Breadth of the foundation to be greater than that
of the Genset Base-frame.
•UNLOADING
•Lift the Genset using thelifting eye provided on the
Base frame only
•Use spreader bar, proper
capacity nylon sling/steel rope
and crane.•Keep the genset covered
during Installation.
8/19/2019 Diesel Gen Tips
http://slidepdf.com/reader/full/diesel-gen-tips 8/10
•EXHAUST SYSTEM
•Designed in a way to minimize
the Backpressure.•High backpressure can
lead to:
•Lower fuel economy
•High Exhaust Temp
•Poor engine
perfomance and less
durability•Weight of the Exhaust system not to be supported by the Engine.
•Exhaust pipe recommended to be of Mild steel or can be higher Grade steel
depending on the Spec. requirement
•Exhaust system to be in the direction of prevailing winds•Install Rain-cap at the end.
•Exhaust pipe to be slanted away from the engine.
•Exhaust system to be insulated and lagged.
• Not recommended to use Common Exhaust Pipe for Multiple Engine.
8/19/2019 Diesel Gen Tips
http://slidepdf.com/reader/full/diesel-gen-tips 9/10
•FUEL SYSTEM
•External Fuel piping to be designed considering less restriction.
•
Day fuel tank to be sized min. for 8 hr fuel consumption.•GI piping / Material not to be used wherever there is a contact with Diesel.
•Emergency shut-off valve is recommended.
•Use proper colour coding for fuel pipes.
•Fuel system to be in line with the applicable specifications.
8/19/2019 Diesel Gen Tips
http://slidepdf.com/reader/full/diesel-gen-tips 10/10