Dies Steel L STRAIGHT EJECTOR PINS WITH FREE FLANGE … · 2019-02-26 · Dies Steel SKD61...
Transcript of Dies Steel L STRAIGHT EJECTOR PINS WITH FREE FLANGE … · 2019-02-26 · Dies Steel SKD61...
178
Free Flange-Position
Ejector Pins
177
Dies SteelSKD61 equivalent+
Nitriding
STRAIGHT EJECTOR PINS WITH FREE FLANGE POSITION- L DIMENSION DESIGNATION TYPE/ L・P DIMENSION DESIGNATION TYPE-
Part Number - L - P - S
EPSN5 - 60.00 - S10.00
EPSNB5 - 117.32 - P4.25 - S26.30
H DPart Number 0.01mm increments
Type P L S7 4
EPSN
4
5.00~400.00 5.00~80.008 5 5
9 6 6
10 7 7
5.00~500.00 5.00~80.00
11 8 8
15 10 10
17 12 12
20 15 15
H DPart Number 0.01mm increments
Type No. L P S7 4
EPSNB
4
5.00~400.00
3.50~ 3.99
5.00~80.008 5 5 4.00~ 4.99
9 6 6 5.00~ 5.99
10 7 7
5.00~500.00
6.00~ 6.99
5.00~80.00
11 8 8 7.00~ 7.99
15 10 10 8.00~ 9.99
17 12 12 10.00~11.99
20 15 15 12.00~14.99
Part Number - L - P - S - (HC・TC・DC…etc.)
EPSN5 - 60.00 - S10.00 - TC3.0
EPSNB5 - 60.00 - P4.50 - S10.00 - TC3.0
Alterations Code Spec. 1Code Alterations Code Spec. 1Code
-0.1KC0 KC KC=0.1mm increments
V D/2+0.1≦KC<H/2 KGC0°
AG°±0.5
KGC-0.1
0
KGCKGC=0.1mm incrementsAG=1°incrementsV D/2+0.1≦KGC<H/2, 0<AG<360
WKC -0.10 WKC WKC=0.1mm increments
V D/2+0.1≦WKC<H/2
120°
120°KTC
120°0
-0.1
KTC KTC=0.1mm incrementsV D/2+0.1≦KTC<H/2
KAC KBC -0.10
KACKBC
KAC, KBC=0.1mm incrementsV D/2+0.1≦KAC<KBC<H/2 H
0-
0.3
HC
HC HC=0.1mm incrementsV P+1≦HC<H
RKC
RKC0
-0.1RKC RKC=0.1mm increments
V D/2+0.1≦RKC<H/2 4S
TC -0.020 TC
TC=0.1mm incrementsV 2.0≦TC≦10 and TC≦L-10
(Dimensions L and S remain unchanged.)
0DKC DKC -0.1
DKC
DKC DKC=0.1mm incrementsV D/2+0.1≦DKC<H/2 DC
-0.10
D
DC
DC=0.1mm incrementsV P-1≦DC<DV Available for L・P Dimension designation type only.V Only available combination is with HC・TC
SKC
SKC -0.10 SKC SKC=0.1mm increments
V D/2+0.1≦SKC<H/2
S L
L dimension designation type
S L
L・P dimension designation type
P.L.
Z
P.L. P.L.
Fixed dieplate
Submarine gate
Cavity Finished products Runner
die plateMovable
Base clamping
Core
Ejector plate
Ejector plate
(Upper)
(Lower)
plate
Finished products
Runner
Runner
Fig. 1 ● Mold closed Fig. 2 ● Mold opening Fig. 3 ● Mold opened
Part Number Head Thickness T P
EPSN (L dimension designation type) 4mm(T4)
-0.01-0.02
EPSNB (L・P dimension designation type)
-0.1 0
1.6
C≦0.3
S-0.050
H0-
0.3
2-R≦0.5
-0.05 0
T=4
1.6GD
G
-0.01-0.02PL
+0.050
R SKD61 equivalent+NitridedQ Surface : 900HV~ Base material:40~45HRC Range of guaranteed base material hardness
(Details XP.1303)
Dies SteelSKD61 equivalent
+Nitrided
V Both end faces are not nitrided to prevent them from chipping.
Free flange position ejector pins can be ejected in differential time.The runner can be slowly ejected by the depth of counter bore Z (Fig.1).They are applicable to ejection of molded products and two-step ejection.
V Non JIS material definition is listed on P.1351 - 1352
Alteration details XP.174
QuotationQuotation
QuotationQuotation
Quo
tati
on
Quo
tati
on
Quo
tati
on
Quo
tati
on