DIAGNOSTIC - ww.xegatrack.comww.xegatrack.com/QueclinkDocs/Diagrams CAN100/CAN-JCB-JS175W.pdfJCB...

1
JCB JS175W rev. 2016/04/01 CAN-Logistic II TERMINAL GPRS/GPS A B E F G H J D C CAUTION! Connect CAN-bus ([S2-1] and [S2-4]) strictly according to the installation guide. Connecting to any other twisted pair (even if colours are the same) either reduces the number of available information or completely disables communication. CAUTION! CAN-Logistic's twisted-pairs (CAN-bus and J1708) must be shortened as much as possible (recommended length is max. 20 cm). It cannot get tangled or rolled. * Output [S2-2] is a signal from CAN bus that the ignition is turned on. If the Terminal GPRS/GPS uses signals from the ignition system of the vehicle, leave the output [S2-2] unconnected. Do not connect the output [S2-2] to any of the car’s wires. It can be connected ONLY to Terminal GPRS/GPS. DIAGNOSTIC CONNECTOR [S2-1] CANH, ORANGE/GREEN [S2-4] CANL, ORANGE/BROWN [S1-4] GROUND, BLACK [S1-3] POWER SUPPLY +12/24V, RED [S2-2] POSITIVE WHEN ENGINE ON, BROWN [S1-1] SERIAL PORT TX, BLUE/YELLOW [S1-2] SERIAL PORT RX, BLUE/RED OUTPUT Excavator Required special firmware version min. 2.2.05[1] Setting: “JCB JS175W” (ID=85) All rights reserved. PIN C - RED PIN D - BLUE

Transcript of DIAGNOSTIC - ww.xegatrack.comww.xegatrack.com/QueclinkDocs/Diagrams CAN100/CAN-JCB-JS175W.pdfJCB...

Page 1: DIAGNOSTIC - ww.xegatrack.comww.xegatrack.com/QueclinkDocs/Diagrams CAN100/CAN-JCB-JS175W.pdfJCB JS175W rev. 2016/04/01 CAN-Logistic II T E R M I N A L G P R S / G P S A B E F G H

JCB JS175W

rev. 2016/04/01

CAN-Logistic II

TE

RM

INA

L G

PR

S/G

PS

A B

E

F

GH

J

DC

CAUTION! Connect CAN-bus ([S2-1] and [S2-4]) strictly according to the installation guide. Connecting to any other twisted pair (even if colours are the same) either reduces the number of available information or completely disables communication.

CAUTION! CAN-Logistic's twisted-pairs (CAN-bus and J1708) must be shortened as much as possible (recommended length is max. 20 cm). It cannot get tangled or rolled.

* Output [S2-2] is a signal from CAN bus that the ignition is turned on. If the Terminal GPRS/GPS uses signals from the ignition system of the vehicle, leave the output [S2-2] unconnected.Do not connect the output [S2-2] to any of the car’s wires. It can be connected ONLY to Terminal GPRS/GPS.

DIAGNOSTICCONNECTOR

[S2-1] CANH, ORANGE/GREEN

[S2-4] CANL, ORANGE/BROWN

[S1-4] GROUND, BLACK

[S1-3] POWER SUPPLY +12/24V, RED

[S2-2] POSITIVE WHEN ENGINE ON, BROWN

[S1-1] SERIAL PORT TX, BLUE/YELLOW

[S1-2] SERIAL PORT RX, BLUE/RED

OUTPUT

Excavator

Required special firmware version min. 2.2.05[1]Setting: “JCB JS175W” (ID=85)

All rights reserved.

PIN

C -

RE

D

PIN

D -

BL

UE