Dextrose Monohydrate (D-Glucose) - Cambridge Commodities
Transcript of Dextrose Monohydrate (D-Glucose) - Cambridge Commodities
Dextrose Monohydrate (D-Glucose)Cambridge Commodities Chemwatch Hazard Alert Code: 0
Part Number: P04039
Version No: 3.3
Safety data sheet according to REACH Regulation (EC) No 1907/2006, as amended by UK REACH Regulations SI 2019/758
Issue Date: 13/12/2021
Print Date: 04/06/2022
S.REACH.GB.EN
SECTION 1 Identification of the substance / mixture and of the company / undertaking
1.1. Product Identifier
Product name Dextrose Monohydrate (D-Glucose)
Chemical Name D-glucose
Synonyms Not Available
Chemical formula Not Applicable
Other means ofidentification
P04039
1.2. Relevant identified uses of the substance or mixture and uses advised against
Relevant identified uses Use according to manufacturer's directions.
Uses advised against Not Applicable
1.3. Details of the supplier of the safety data sheet
Registered company name Cambridge Commodities
Address Lancaster Way Business Park, Ely, Cambridgeshire Cambridgeshire CB6 3NX United Kingdom
Telephone +44 1353 667258
Fax Not Available
Website
Email [email protected]
1.4. Emergency telephone number
Association / Organisation Not Available
Emergency telephonenumbers
Not Available
Other emergencytelephone numbers
Not Available
Not Available
Product code: P04039 Version No: 3.3 Page 1 of 18
SECTION 2 Hazards identification
2.1. Classification of the substance or mixture
Classified according toGB-CLP Regulation, UK SI
2019/720 and UK SI
2020/1567 [1]
Not Applicable
2.2. Label elements
Hazard pictogram(s) Not Applicable
Signal word Not Applicable
Hazard statement(s)
Not Applicable
Supplementary statement(s)
Not Applicable
Precautionary statement(s) Prevention
Not Applicable
Precautionary statement(s) Response
Not Applicable
Precautionary statement(s) Storage
Not Applicable
Precautionary statement(s) Disposal
Not Applicable
2.3. Other hazards
REACh - Art.57-59: The mixture does not contain Substances of Very High Concern (SVHC) at the SDS print date.
Not Applicable
SECTION 3 Composition / information on ingredients
3.1.Substances
See 'Composition on ingredients' in Section 3.2
3.2.Mixtures
1.CAS No2.EC No3.Index No
%[weight] NameClassified according to GB-CLP Regulation, UKSI 2019/720 and UK SI 2020/1567
SCL /M-Factor
Nanoform ParticleCharacteristics
S.REACH.GB.ENSafety Data Sheet (Conforms to Annex II of REACH (1907/2006) - Regulation 2020/878)Chemwatch: 9-636846Issue Date: 13/12/2021Print Date: 04/06/2022
Lancaster Way Business ParkEly, Cambridgeshire, CB6 3NX, UK.
+44 (0) 1353 [email protected]
Product code: P04039 Version No: 3.3 Page 2 of 18
4.REACH No
1.5996-10-12.200-075-13.Not Available4.Not Available
100 Not ApplicableNotAvailable
Not Available
Legend: 1. Classified by Chemwatch; 2. Classification drawn from GB-CLP Regulation, UK SI 2019/720 and UK SI 2020/1567; 3.Classification drawn from C&L; * EU IOELVs available; [e] Substance identified as having endocrine disrupting properties
SECTION 4 First aid measures
4.1. Description of first aid measures
Eye Contact
If this product comes in contact with eyes:Wash out immediately with water.If irritation continues, seek medical attention.Removal of contact lenses after an eye injury should only be undertaken by skilled personnel.
Skin ContactIf skin or hair contact occurs:
Flush skin and hair with running water (and soap if available).Seek medical attention in event of irritation.
InhalationIf fumes, aerosols or combustion products are inhaled remove from contaminated area.Other measures are usually unnecessary.
IngestionImmediately give a glass of water.First aid is not generally required. If in doubt, contact a Poisons Information Centre or a doctor.
4.2 Most important symptoms and effects, both acute and delayed
See Section 11
4.3. Indication of any immediate medical attention and special treatment needed
Treat symptomatically.
SECTION 5 Firefighting measures
5.1. Extinguishing media
Foam.
Dry chemical powder.
BCF (where regulations permit).
Carbon dioxide.
Water spray or fog - Large fires only.
5.2. Special hazards arising from the substrate or mixture
Fire IncompatibilityAvoid contamination with oxidising agents i.e. nitrates, oxidising acids, chlorine bleaches, pool chlorine etc. as ignition mayresult
5.3. Advice for firefighters
Fire FightingAlert Fire Brigade and tell them location and nature of hazard.Wear breathing apparatus plus protective gloves.
D-glucose
S.REACH.GB.ENSafety Data Sheet (Conforms to Annex II of REACH (1907/2006) - Regulation 2020/878)Chemwatch: 9-636846Issue Date: 13/12/2021Print Date: 04/06/2022
Lancaster Way Business ParkEly, Cambridgeshire, CB6 3NX, UK.
+44 (0) 1353 [email protected]
Product code: P04039 Version No: 3.3 Page 3 of 18
Prevent, by any means available, spillage from entering drains or water courses.Use water delivered as a fine spray to control fire and cool adjacent area.DO NOT approach containers suspected to be hot.Cool fire exposed containers with water spray from a protected location.If safe to do so, remove containers from path of fire.Equipment should be thoroughly decontaminated after use.
Fire/Explosion Hazard
Combustible solid which burns but propagates flame with difficulty; it is estimated that most organic dusts are combustible(circa 70%) - according to the circumstances under which the combustion process occurs, such materials may cause firesand / or dust explosions.Organic powders when finely divided over a range of concentrations regardless of particulate size or shape and suspended inair or some other oxidizing medium may form explosive dust-air mixtures and result in a fire or dust explosion (includingsecondary explosions).Avoid generating dust, particularly clouds of dust in a confined or unventilated space as dusts may form an explosive mixturewith air, and any source of ignition, i.e. flame or spark, will cause fire or explosion. Dust clouds generated by the fine grindingof the solid are a particular hazard; accumulations of fine dust (420 micron or less) may burn rapidly and fiercely if ignited -particles exceeding this limit will generally not form flammable dust clouds; once initiated, however, larger particles up to 1400microns diameter will contribute to the propagation of an explosion.In the same way as gases and vapours, dusts in the form of a cloud are only ignitable over a range of concentrations; inprinciple, the concepts of lower explosive limit (LEL) and upper explosive limit (UEL) are applicable to dust clouds but onlythe LEL is of practical use; - this is because of the inherent difficulty of achieving homogeneous dust clouds at hightemperatures (for dusts the LEL is often called the "Minimum Explosible Concentration", MEC).When processed with flammable liquids/vapors/mists,ignitable (hybrid) mixtures may be formed with combustible dusts.Ignitable mixtures will increase the rate of explosion pressure rise and the Minimum Ignition Energy (the minimum amount ofenergy required to ignite dust clouds - MIE) will be lower than the pure dust in air mixture. The Lower Explosive Limit (LEL) ofthe vapour/dust mixture will be lower than the individual LELs for the vapors/mists or dusts.A dust explosion may release of large quantities of gaseous products; this in turn creates a subsequent pressure rise ofexplosive force capable of damaging plant and buildings and injuring people.Usually the initial or primary explosion takes place in a confined space such as plant or machinery, and can be of sufficientforce to damage or rupture the plant. If the shock wave from the primary explosion enters the surrounding area, it will disturbany settled dust layers, forming a second dust cloud, and often initiate a much larger secondary explosion. All large scaleexplosions have resulted from chain reactions of this type.Dry dust can be charged electrostatically by turbulence, pneumatic transport, pouring, in exhaust ducts and during transport.Build-up of electrostatic charge may be prevented by bonding and grounding.Powder handling equipment such as dust collectors, dryers and mills may require additional protection measures such asexplosion venting.All movable parts coming in contact with this material should have a speed of less than 1-meter/sec.A sudden release of statically charged materials from storage or process equipment, particularly at elevated temperaturesand/ or pressure, may result in ignition especially in the absence of an apparent ignition source.One important effect of the particulate nature of powders is that the surface area and surface structure (and often moisturecontent) can vary widely from sample to sample, depending of how the powder was manufactured and handled; this meansthat it is virtually impossible to use flammability data published in the literature for dusts (in contrast to that published forgases and vapours).Autoignition temperatures are often quoted for dust clouds (minimum ignition temperature (MIT)) and dust layers (layerignition temperature (LIT)); LIT generally falls as the thickness of the layer increases.
Combustion products include:,carbon monoxide (CO),carbon dioxide (CO2),other pyrolysis products typical of burning organic material.
SECTION 6 Accidental release measures
S.REACH.GB.ENSafety Data Sheet (Conforms to Annex II of REACH (1907/2006) - Regulation 2020/878)Chemwatch: 9-636846Issue Date: 13/12/2021Print Date: 04/06/2022
Lancaster Way Business ParkEly, Cambridgeshire, CB6 3NX, UK.
+44 (0) 1353 [email protected]
Product code: P04039 Version No: 3.3 Page 4 of 18
6.1. Personal precautions, protective equipment and emergency procedures
See section 8
6.2. Environmental precautions
See section 12
6.3. Methods and material for containment and cleaning up
Minor Spills
Clean up all spills immediately.Avoid contact with skin and eyes.Wear impervious gloves and safety glasses.Use dry clean up procedures and avoid generating dust.Vacuum up (consider explosion-proof machines designed to be grounded during storage and use).Do NOT use air hoses for cleaningPlace spilled material in clean, dry, sealable, labelled container.
Major Spills
Clear area of personnel and move upwind.Alert Fire Brigade and tell them location and nature of hazard.Control personal contact with the substance, by using protective equipment and dust respirator.Prevent spillage from entering drains, sewers or water courses.Avoid generating dust.Sweep, shovel up. Recover product wherever possible.Put residues in labelled plastic bags or other containers for disposal.If contamination of drains or waterways occurs, advise emergency services.
6.4. Reference to other sections
Personal Protective Equipment advice is contained in Section 8 of the SDS.
SECTION 7 Handling and storage
7.1. Precautions for safe handling
Safe handling
Limit all unnecessary personal contact.Wear protective clothing when risk of exposure occurs.Use in a well-ventilated area.Avoid contact with incompatible materials.When handling, DO NOT eat, drink or smoke.Keep containers securely sealed when not in use.Avoid physical damage to containers.Always wash hands with soap and water after handling.Work clothes should be laundered separately.Use good occupational work practice.Observe manufacturer's storage and handling recommendations contained within this SDS.Atmosphere should be regularly checked against established exposure standards to ensure safe working conditions aremaintained.Organic powders when finely divided over a range of concentrations regardless of particulate size or shape and suspended inair or some other oxidizing medium may form explosive dust-air mixtures and result in a fire or dust explosion (includingsecondary explosions)Minimise airborne dust and eliminate all ignition sources. Keep away from heat, hot surfaces, sparks, and flame.
S.REACH.GB.ENSafety Data Sheet (Conforms to Annex II of REACH (1907/2006) - Regulation 2020/878)Chemwatch: 9-636846Issue Date: 13/12/2021Print Date: 04/06/2022
Lancaster Way Business ParkEly, Cambridgeshire, CB6 3NX, UK.
+44 (0) 1353 [email protected]
Product code: P04039 Version No: 3.3 Page 5 of 18
Establish good housekeeping practices.Remove dust accumulations on a regular basis by vacuuming or gentle sweeping to avoid creating dust clouds.Use continuous suction at points of dust generation to capture and minimise the accumulation of dusts. Particular attentionshould be given to overhead and hidden horizontal surfaces to minimise the probability of a "secondary" explosion. Accordingto NFPA Standard 654, dust layers 1/32 in.(0.8 mm) thick can be sufficient to warrant immediate cleaning of the area.Do not use air hoses for cleaning.Minimise dry sweeping to avoid generation of dust clouds. Vacuum dust-accumulating surfaces and remove to a chemicaldisposal area. Vacuums with explosion-proof motors should be used.Control sources of static electricity. Dusts or their packages may accumulate static charges, and static discharge can be asource of ignition.Solids handling systems must be designed in accordance with applicable standards (e.g. NFPA including 654 and 77) andother national guidance.Do not empty directly into flammable solvents or in the presence of flammable vapors.The operator, the packaging container and all equipment must be grounded with electrical bonding and grounding systems.Plastic bags and plastics cannot be grounded, and antistatic bags do not completely protect against development of staticcharges.
Empty containers may contain residual dust which has the potential to accumulate following settling. Such dusts may explode inthe presence of an appropriate ignition source.
Do NOT cut, drill, grind or weld such containers.In addition ensure such activity is not performed near full, partially empty or empty containers without appropriate workplacesafety authorisation or permit.
Fire and explosionprotection
See section 5
Other information
Store in original containers.Keep containers securely sealed.Store in a cool, dry area protected from environmental extremes.Store away from incompatible materials and foodstuff containers.Protect containers against physical damage and check regularly for leaks.Observe manufacturer's storage and handling recommendations contained within this SDS.
For major quantities:Consider storage in bunded areas - ensure storage areas are isolated from sources of community water (includingstormwater, ground water, lakes and streams}.Ensure that accidental discharge to air or water is the subject of a contingency disaster management plan; this may requireconsultation with local authorities.
7.2. Conditions for safe storage, including any incompatibilities
Suitable container
Lined metal can, lined metal pail/ can.Plastic pail.Polyliner drum.Packing as recommended by manufacturer.Check all containers are clearly labelled and free from leaks.Glass container is suitable for laboratory quantities
Storage incompatibility
Avoid contamination of water, foodstuffs, feed or seed.Reducing sugar-based material.Autooxidation of reducing sugars may produce up to 3000 ppm carbon monoxide under moderately alkaline conditions. High pHaqueous solutions of saccharides (aldoses, ketoses) or polysaccharides based on these sugars may generate hazardousatmospheres in confined spaces.Reducing sugars contain an aldehyde or free hemiacetal in the open-chain form. Sugars with ketone groups in their open chainform are capable of isomerising via a series of tautomeric shifts to produce an aldehyde group in solution. Therefore, ketone-bearing sugars like fructose are considered reducing sugars but it is the isomer containing an aldehyde group which is reducingsince ketones cannot be oxidized without decomposition of the sugar.Many disaccharides, like lactose and maltose, also have a reducing form, as one of the two units may have an open-chain form
S.REACH.GB.ENSafety Data Sheet (Conforms to Annex II of REACH (1907/2006) - Regulation 2020/878)Chemwatch: 9-636846Issue Date: 13/12/2021Print Date: 04/06/2022
Lancaster Way Business ParkEly, Cambridgeshire, CB6 3NX, UK.
+44 (0) 1353 [email protected]
Product code: P04039 Version No: 3.3 Page 6 of 18
with an aldehyde group. However, sucrose and trehalose, in which the anomeric carbons of the two units are linked together, arenon-reducing disaccharides since neither of the rings is capable of opening.In glucose polymers such as starch and starch-derivatives like glucose syrup, maltodextrin and dextrin the macromolecule beginswith a reducing sugar, a free aldehyde. More hydrolysed starch contains more reducing sugars. The percentage of reducingsugars present in these starch derivatives is called dextrose equivalent (DE).Dilute solutions of all sugars are subject to fermentation, either by yeast or by other microorganisms or enzymes derived fromthese, producing gases which can pressurise and burst sealed containers.Some microorganisms will produce hydrogen or methane, adding a fire and explosion hazard.
Avoid reaction with oxidising agents
7.3. Specific end use(s)
See section 1.2
SECTION 8 Exposure controls / personal protection
8.1. Control parameters
IngredientDNELsExposure Pattern Worker
PNECsCompartment
Not Available Not Available Not Available
* Values for General Population
Occupational Exposure Limits (OEL)
INGREDIENT DATA
Source Ingredient Material name TWA STEL Peak Notes
Not Available Not Available Not Available Not Available Not Available Not Available Not Available
Not Applicable
Emergency Limits
Ingredient TEEL-1 TEEL-2 TEEL-3
Dextrose Monohydrate(D-Glucose)
Not Available Not Available Not Available
Ingredient Original IDLH Revised IDLH
D-glucose Not Available Not Available
8.2. Exposure controls
8.2.1. Appropriateengineering controls
Engineering controls are used to remove a hazard or place a barrier between the worker and the hazard. Well-designedengineering controls can be highly effective in protecting workers and will typically be independent of worker interactions toprovide this high level of protection.The basic types of engineering controls are:Process controls which involve changing the way a job activity or process is done to reduce the risk.Enclosure and/or isolation of emission source which keeps a selected hazard "physically" away from the worker and ventilationthat strategically "adds" and "removes" air in the work environment. Ventilation can remove or dilute an air contaminant ifdesigned properly. The design of a ventilation system must match the particular process and chemical or contaminant in use.Employers may need to use multiple types of controls to prevent employee overexposure.
S.REACH.GB.ENSafety Data Sheet (Conforms to Annex II of REACH (1907/2006) - Regulation 2020/878)Chemwatch: 9-636846Issue Date: 13/12/2021Print Date: 04/06/2022
Lancaster Way Business ParkEly, Cambridgeshire, CB6 3NX, UK.
+44 (0) 1353 [email protected]
Product code: P04039 Version No: 3.3 Page 7 of 18
Local exhaust ventilation is required where solids are handled as powders or crystals; even when particulates are relativelylarge, a certain proportion will be powdered by mutual friction.Exhaust ventilation should be designed to prevent accumulation and recirculation of particulates in the workplace.If in spite of local exhaust an adverse concentration of the substance in air could occur, respiratory protection should beconsidered. Such protection might consist of:
(a): particle dust respirators, if necessary, combined with an absorption cartridge;(b): filter respirators with absorption cartridge or canister of the right type;(c): fresh-air hoods or masks
Build-up of electrostatic charge on the dust particle, may be prevented by bonding and grounding.Powder handling equipment such as dust collectors, dryers and mills may require additional protection measures such asexplosion venting.
Air contaminants generated in the workplace possess varying "escape" velocities which, in turn, determine the "capturevelocities" of fresh circulating air required to efficiently remove the contaminant.
Type of Contaminant: Air Speed:
direct spray, spray painting in shallow booths, drum filling, conveyer loading, crusher dusts, gasdischarge (active generation into zone of rapid air motion)
1-2.5 m/s (200-500ft/min)
grinding, abrasive blasting, tumbling, high speed wheel generated dusts (released at high initialvelocity into zone of very high rapid air motion).
2.5-10 m/s(500-2000 ft/min)
Within each range the appropriate value depends on:
Lower end of the range Upper end of the range
1: Room air currents minimal or favourable to capture 1: Disturbing room air currents
2: Contaminants of low toxicity or of nuisance value only 2: Contaminants of high toxicity
3: Intermittent, low production. 3: High production, heavy use
4: Large hood or large air mass in motion 4: Small hood-local control only
Simple theory shows that air velocity falls rapidly with distance away from the opening of a simple extraction pipe. Velocitygenerally decreases with the square of distance from the extraction point (in simple cases). Therefore the air speed at theextraction point should be adjusted, accordingly, after reference to distance from the contaminating source. The air velocity at theextraction fan, for example, should be a minimum of 4-10 m/s (800-2000 ft/min) for extraction of crusher dusts generated 2metres distant from the extraction point. Other mechanical considerations, producing performance deficits within the extractionapparatus, make it essential that theoretical air velocities are multiplied by factors of 10 or more when extraction systems areinstalled or used.
8.2.2. Personal protection
Eye and face protection
Safety glasses with side shieldsChemical goggles.Contact lenses may pose a special hazard; soft contact lenses may absorb and concentrate irritants. A written policydocument, describing the wearing of lenses or restrictions on use, should be created for each workplace or task. This shouldinclude a review of lens absorption and adsorption for the class of chemicals in use and an account of injury experience.Medical and first-aid personnel should be trained in their removal and suitable equipment should be readily available. In theevent of chemical exposure, begin eye irrigation immediately and remove contact lens as soon as practicable. Lens shouldbe removed at the first signs of eye redness or irritation - lens should be removed in a clean environment only after workershave washed hands thoroughly. [CDC NIOSH Current Intelligence Bulletin 59], [AS/NZS 1336 or national equivalent]
Skin protection See Hand protection below
Hands/feet protection
The selection of suitable gloves does not only depend on the material, but also on further marks of quality which vary frommanufacturer to manufacturer. Where the chemical is a preparation of several substances, the resistance of the glove materialcan not be calculated in advance and has therefore to be checked prior to the application.
S.REACH.GB.ENSafety Data Sheet (Conforms to Annex II of REACH (1907/2006) - Regulation 2020/878)Chemwatch: 9-636846Issue Date: 13/12/2021Print Date: 04/06/2022
Lancaster Way Business ParkEly, Cambridgeshire, CB6 3NX, UK.
+44 (0) 1353 [email protected]
Product code: P04039 Version No: 3.3 Page 8 of 18
The exact break through time for substances has to be obtained from the manufacturer of the protective gloves and has to beobserved when making a final choice.Personal hygiene is a key element of effective hand care. Gloves must only be worn on clean hands. After using gloves, handsshould be washed and dried thoroughly. Application of a non-perfumed moisturiser is recommended.Suitability and durability of glove type is dependent on usage. Important factors in the selection of gloves include:· frequency and duration of contact,· chemical resistance of glove material,· glove thickness and· dexteritySelect gloves tested to a relevant standard (e.g. Europe EN 374, US F739, AS/NZS 2161.1 or national equivalent).· When prolonged or frequently repeated contact may occur, a glove with a protection class of 5 or higher (breakthrough timegreater than 240 minutes according to EN 374, AS/NZS 2161.10.1 or national equivalent) is recommended.· When only brief contact is expected, a glove with a protection class of 3 or higher (breakthrough time greater than 60 minutesaccording to EN 374, AS/NZS 2161.10.1 or national equivalent) is recommended.· Some glove polymer types are less affected by movement and this should be taken into account when considering gloves forlong-term use.· Contaminated gloves should be replaced.As defined in ASTM F-739-96 in any application, gloves are rated as:· Excellent when breakthrough time > 480 min· Good when breakthrough time > 20 min· Fair when breakthrough time < 20 min· Poor when glove material degradesFor general applications, gloves with a thickness typically greater than 0.35 mm, are recommended.It should be emphasised that glove thickness is not necessarily a good predictor of glove resistance to a specific chemical, as thepermeation efficiency of the glove will be dependent on the exact composition of the glove material. Therefore, glove selectionshould also be based on consideration of the task requirements and knowledge of breakthrough times.Glove thickness may also vary depending on the glove manufacturer, the glove type and the glove model. Therefore, themanufacturers technical data should always be taken into account to ensure selection of the most appropriate glove for the task.Note: Depending on the activity being conducted, gloves of varying thickness may be required for specific tasks. For example:· Thinner gloves (down to 0.1 mm or less) may be required where a high degree of manual dexterity is needed. However, thesegloves are only likely to give short duration protection and would normally be just for single use applications, then disposed of.· Thicker gloves (up to 3 mm or more) may be required where there is a mechanical (as well as a chemical) risk i.e. where thereis abrasion or puncture potentialGloves must only be worn on clean hands. After using gloves, hands should be washed and dried thoroughly. Application of anon-perfumed moisturiser is recommended.Experience indicates that the following polymers are suitable as glove materials for protection against undissolved, dry solids,where abrasive particles are not present.
polychloroprene.nitrile rubber.butyl rubber.fluorocaoutchouc.polyvinyl chloride.
Gloves should be examined for wear and/ or degradation constantly.
Body protection See Other protection below
Other protection
No special equipment needed when handling small quantities.OTHERWISE:
Overalls.Barrier cream.Eyewash unit.
Respiratory protection
Particulate. (AS/NZS 1716 & 1715, EN 143:2000 & 149:001, ANSI Z88 or national equivalent)
S.REACH.GB.ENSafety Data Sheet (Conforms to Annex II of REACH (1907/2006) - Regulation 2020/878)Chemwatch: 9-636846Issue Date: 13/12/2021Print Date: 04/06/2022
Lancaster Way Business ParkEly, Cambridgeshire, CB6 3NX, UK.
+44 (0) 1353 [email protected]
Product code: P04039 Version No: 3.3 Page 9 of 18
Required Minimum Protection Factor Half-Face Respirator Full-Face Respirator Powered Air Respirator
up to 10 x ESP1Air-line*
--
PAPR-P1-
up to 50 x ES Air-line** P2 PAPR-P2
up to 100 x ES - P3 -
Air-line* -
100+ x ES - Air-line** PAPR-P3
* - Negative pressure demand ** - Continuous flow
A(All classes) = Organic vapours, B AUS or B1 = Acid gasses, B2 = Acid gas or hydrogen cyanide(HCN), B3 = Acid gas or hydrogen cyanide(HCN), E = Sulfur
dioxide(SO2), G = Agricultural chemicals, K = Ammonia(NH3), Hg = Mercury, NO = Oxides of nitrogen, MB = Methyl bromide, AX = Low boiling point organic
compounds(below 65 degC)
· Respirators may be necessary when engineering and administrative controls do not adequately prevent exposures.
· The decision to use respiratory protection should be based on professional judgment that takes into account toxicity information, exposure measurement data,
and frequency and likelihood of the worker's exposure - ensure users are not subject to high thermal loads which may result in heat stress or distress due to
personal protective equipment (powered, positive flow, full face apparatus may be an option).
· Published occupational exposure limits, where they exist, will assist in determining the adequacy of the selected respiratory protection. These may be
government mandated or vendor recommended.
· Certified respirators will be useful for protecting workers from inhalation of particulates when properly selected and fit tested as part of a complete respiratory
protection program.
· Where protection from nuisance levels of dusts are desired, use type N95 (US) or type P1 (EN143) dust masks. Use respirators and components tested and
approved under appropriate government standards such as NIOSH (US) or CEN (EU)
· Use approved positive flow mask if significant quantities of dust becomes airborne.
· Try to avoid creating dust conditions.
8.2.3. Environmental exposure controls
See section 12
SECTION 9 Physical and chemical properties
9.1. Information on basic physical and chemical properties
Appearance Not Available
Physical state Divided Solid|PowderRelative density (Water =
1)Not Available
Odour Not AvailablePartition coefficient
n-octanol / waterNot Available
Odour threshold Not AvailableAuto-ignition temperature
(°C)Not Available
pH (as supplied) Not AvailableDecomposition
temperatureNot Available
Melting point / freezingpoint (°C)
Not Available Viscosity (cSt) Not Available
Initial boiling point andboiling range (°C)
Not Available Molecular weight (g/mol) Not Available
Flash point (°C) Not Available Taste Not Available
S.REACH.GB.ENSafety Data Sheet (Conforms to Annex II of REACH (1907/2006) - Regulation 2020/878)Chemwatch: 9-636846Issue Date: 13/12/2021Print Date: 04/06/2022
Lancaster Way Business ParkEly, Cambridgeshire, CB6 3NX, UK.
+44 (0) 1353 [email protected]
Product code: P04039 Version No: 3.3 Page 10 of 18
Evaporation rate Not Available Explosive properties Not Available
Flammability Not Available Oxidising properties Not Available
Upper Explosive Limit (%) Not AvailableSurface Tension (dyn/cm
or mN/m)Not Applicable
Lower Explosive Limit (%) Not Available Volatile Component (%vol) Not Available
Vapour pressure (kPa) Not Available Gas group Not Available
Solubility in water ImmisciblepH as a solution (Not
Available%)Not Available
Vapour density (Air = 1) Not Available VOC g/L Not Available
Nanoform Solubility Not AvailableNanoform Particle
CharacteristicsNot Available
Particle Size Not Available
9.2. Other information
Not Available
SECTION 10 Stability and reactivity
10.1.Reactivity See section 7.2
10.2. Chemical stability Product is considered stable and hazardous polymerisation will not occur.
10.3. Possibility ofhazardous reactions
See section 7.2
10.4. Conditions to avoid See section 7.2
10.5. Incompatiblematerials
See section 7.2
10.6. Hazardousdecomposition products
See section 5.3
SECTION 11 Toxicological information
11.1. Information on toxicological effects
Inhaled
The material is not thought to produce adverse health effects or irritation of the respiratory tract (as classified by EC Directivesusing animal models). Nevertheless, good hygiene practice requires that exposure be kept to a minimum and that suitable controlmeasures be used in an occupational setting.Persons with impaired respiratory function, airway diseases and conditions such as emphysema or chronic bronchitis, may incurfurther disability if excessive concentrations of particulate are inhaled.If prior damage to the circulatory or nervous systems has occurred or if kidney damage has been sustained, proper screeningsshould be conducted on individuals who may be exposed to further risk if handling and use of the material result in excessiveexposures.
IngestionThe material has NOT been classified by EC Directives or other classification systems as "harmful by ingestion". This is becauseof the lack of corroborating animal or human evidence.
Skin ContactThe material is not thought to produce adverse health effects or skin irritation following contact (as classified by EC Directivesusing animal models). Nevertheless, good hygiene practice requires that exposure be kept to a minimum and that suitable glovesbe used in an occupational setting.
S.REACH.GB.ENSafety Data Sheet (Conforms to Annex II of REACH (1907/2006) - Regulation 2020/878)Chemwatch: 9-636846Issue Date: 13/12/2021Print Date: 04/06/2022
Lancaster Way Business ParkEly, Cambridgeshire, CB6 3NX, UK.
+44 (0) 1353 [email protected]
Product code: P04039 Version No: 3.3 Page 11 of 18
Legend: – Data either not available or does not fill the criteria for classification – Data available to make classification
EyeAlthough the material is not thought to be an irritant (as classified by EC Directives), direct contact with the eye may causetransient discomfort characterised by tearing or conjunctival redness (as with windburn). Slight abrasive damage may also result.
Chronic
Long-term exposure to the product is not thought to produce chronic effects adverse to the health (as classified by EC Directivesusing animal models); nevertheless exposure by all routes should be minimised as a matter of course.Long term exposure to high dust concentrations may cause changes in lung function i.e. pneumoconiosis, caused by particlesless than 0.5 micron penetrating and remaining in the lung.
Dextrose Monohydrate(D-Glucose)
TOXICITY IRRITATION
Not Available Not Available
D-glucoseTOXICITY IRRITATION
Oral (Rat) LD50; 25800 mg/kg[2] Not Available
Legend: 1. Value obtained from Europe ECHA Registered Substances - Acute toxicity 2.* Value obtained from manufacturer's SDS. Unless otherwise specified data extracted from RTECS - Register of Toxic Effect of chemical Substances
D-GLUCOSE Specific development abnormalities reported in foetus include craniofacial, hepatobiliary, urogenital.
Acute Toxicity Carcinogenicity
Skin Irritation/Corrosion Reproductivity
Serious EyeDamage/Irritation
STOT - Single Exposure
Respiratory or Skinsensitisation
STOT - Repeated Exposure
Mutagenicity Aspiration Hazard
11.2.1. Endocrine Disruption Properties
Not Available
SECTION 12 Ecological information
12.1. Toxicity
Dextrose Monohydrate(D-Glucose)
Endpoint Test Duration (hr) Species Value Source
NotAvailable
Not Available Not AvailableNotAvailable
NotAvailable
D-glucoseEndpoint Test Duration (hr) Species Value Source
EC10(ECx) 48h Fish 12.611-4720.192mg/L 4
Legend: Extracted from 1. IUCLID Toxicity Data 2. Europe ECHA Registered Substances - Ecotoxicological Information - Aquatic Toxicity 4. US EPA, Ecotox database - Aquatic Toxicity Data 5. ECETOC Aquatic Hazard Assessment Data 6. NITE (Japan) -Bioconcentration Data 7. METI (Japan) - Bioconcentration Data 8. Vendor Data
S.REACH.GB.ENSafety Data Sheet (Conforms to Annex II of REACH (1907/2006) - Regulation 2020/878)Chemwatch: 9-636846Issue Date: 13/12/2021Print Date: 04/06/2022
Lancaster Way Business ParkEly, Cambridgeshire, CB6 3NX, UK.
+44 (0) 1353 [email protected]
Product code: P04039 Version No: 3.3 Page 12 of 18
12.2. Persistence and degradability
Ingredient Persistence: Water/Soil Persistence: Air
D-glucose LOW LOW
12.3. Bioaccumulative potential
Ingredient Bioaccumulation
D-glucose LOW (LogKOW = -3.24)
12.4. Mobility in soil
Ingredient Mobility
D-glucose LOW (KOC = 10)
12.5. Results of PBT and vPvB assessment
P B T
Relevant available data Not Available Not Available Not Available
PBT
vPvB
PBT Criteria fulfilled? No
vPvB No
12.6. Endocrine Disruption Properties
Not Available
12.7. Other adverse effects
Not Available
SECTION 13 Disposal considerations
13.1. Waste treatment methods
Product / Packagingdisposal
Legislation addressing waste disposal requirements may differ by country, state and/ or territory. Each user must refer to lawsoperating in their area. In some areas, certain wastes must be tracked.A Hierarchy of Controls seems to be common - the user should investigate:
ReductionReuseRecyclingDisposal (if all else fails)
This material may be recycled if unused, or if it has not been contaminated so as to make it unsuitable for its intended use. Shelflife considerations should also be applied in making decisions of this type. Note that properties of a material may change in use,and recycling or reuse may not always be appropriate. In most instances the supplier of the material should be consulted.
DO NOT allow wash water from cleaning or process equipment to enter drains.It may be necessary to collect all wash water for treatment before disposal.
S.REACH.GB.ENSafety Data Sheet (Conforms to Annex II of REACH (1907/2006) - Regulation 2020/878)Chemwatch: 9-636846Issue Date: 13/12/2021Print Date: 04/06/2022
Lancaster Way Business ParkEly, Cambridgeshire, CB6 3NX, UK.
+44 (0) 1353 [email protected]
Product code: P04039 Version No: 3.3 Page 13 of 18
14.1. UN number
14.2. UN proper shippingname
14.3. Transport hazardclass(es)
14.4. Packing group
14.5. Environmentalhazard
14.6. Special precautionsfor user
14.1. UN number
14.2. UN proper shippingname
14.3. Transport hazardclass(es)
14.4. Packing group
14.5. Environmentalhazard
14.6. Special precautionsfor user
In all cases disposal to sewer may be subject to local laws and regulations and these should be considered first.Where in doubt contact the responsible authority.
Waste treatment options Not Available
Sewage disposal options Not Available
SECTION 14 Transport information
Labels Required
Marine Pollutant NO
HAZCHEM Not Applicable
Land transport (ADR): NOT REGULATED FOR TRANSPORT OF DANGEROUS GOODS
Not Applicable
Not Applicable
Class Not Applicable
Subrisk Not Applicable
Not Applicable
Not Applicable
Hazard identification (Kemler) Not Applicable
Classification code Not Applicable
Hazard Label Not Applicable
Special provisions Not Applicable
Limited quantity Not Applicable
Tunnel Restriction Code Not Applicable
Air transport (ICAO-IATA / DGR): NOT REGULATED FOR TRANSPORT OF DANGEROUS GOODS
Not Applicable
Not Applicable
ICAO/IATA Class Not Applicable
ICAO / IATA Subrisk Not Applicable
ERG Code Not Applicable
Not Applicable
Not Applicable
Special provisions Not Applicable
S.REACH.GB.ENSafety Data Sheet (Conforms to Annex II of REACH (1907/2006) - Regulation 2020/878)Chemwatch: 9-636846Issue Date: 13/12/2021Print Date: 04/06/2022
Lancaster Way Business ParkEly, Cambridgeshire, CB6 3NX, UK.
+44 (0) 1353 [email protected]
Product code: P04039 Version No: 3.3 Page 14 of 18
14.1. UN number
14.2. UN proper shippingname
14.3. Transport hazardclass(es)
14.4. Packing group
14.5. Environmentalhazard
14.6. Special precautionsfor user
14.1. UN number
14.2. UN proper shippingname
14.3. Transport hazardclass(es)
14.4. Packing group
14.5. Environmentalhazard
14.6. Special precautionsfor user
Cargo Only Packing Instructions Not Applicable
Cargo Only Maximum Qty / Pack Not Applicable
Passenger and Cargo Packing Instructions Not Applicable
Passenger and Cargo Maximum Qty / Pack Not Applicable
Passenger and Cargo Limited Quantity Packing Instructions Not Applicable
Passenger and Cargo Limited Maximum Qty / Pack Not Applicable
Sea transport (IMDG-Code / GGVSee): NOT REGULATED FOR TRANSPORT OF DANGEROUS GOODS
Not Applicable
Not Applicable
IMDG Class Not Applicable
IMDG Subrisk Not Applicable
Not Applicable
Not Applicable
EMS Number Not Applicable
Special provisions Not Applicable
Limited Quantities Not Applicable
Inland waterways transport (ADN): NOT REGULATED FOR TRANSPORT OF DANGEROUS GOODS
Not Applicable
Not Applicable
Not Applicable Not Applicable
Not Applicable
Not Applicable
Classification code Not Applicable
Special provisions Not Applicable
Limited quantity Not Applicable
Equipment required Not Applicable
Fire cones number Not Applicable
14.7. Transport in bulk according to Annex II of MARPOL and the IBC code
Not Applicable
14.8. Transport in bulk in accordance with MARPOL Annex V and the IMSBC Code
S.REACH.GB.ENSafety Data Sheet (Conforms to Annex II of REACH (1907/2006) - Regulation 2020/878)Chemwatch: 9-636846Issue Date: 13/12/2021Print Date: 04/06/2022
Lancaster Way Business ParkEly, Cambridgeshire, CB6 3NX, UK.
+44 (0) 1353 [email protected]
Product code: P04039 Version No: 3.3 Page 15 of 18
Product name Group
D-glucose Not Available
14.9. Transport in bulk in accordance with the ICG Code
Product name Ship Type
D-glucose Not Available
SECTION 15 Regulatory information
15.1. Safety, health and environmental regulations / legislation specific for the substance or mixture
D-glucose is found on the following regulatory lists
Europe EC Inventory European Union - European Inventory of Existing Commercial Chemical
Substances (EINECS)
This safety data sheet is in compliance with the following EU legislation and its adaptations - as far as applicable - : Directives 98/24/EC, - 92/85/EEC, - 94/33/EC,
- 2008/98/EC, - 2010/75/EU; Commission Regulation (EU) 2020/878; Regulation (EC) No 1272/2008 as updated through ATPs.
15.2. Chemical safety assessment
No Chemical Safety Assessment has been carried out for this substance/mixture by the supplier.
ECHA SUMMARY
Ingredient CAS number Index No ECHA Dossier
D-glucose 5996-10-1 Not Available Not Available
Harmonisation (C&LInventory)
Hazard Class and Category Code(s) Pictograms Signal Word Code(s) Hazard Statement Code(s)
1 Not Classified Not Available Not Available
2 Eye Irrit. 2B GHS07; Wng H320
1 Not Classified Not Available Not Available
2 Not Classified Not Available Not Available
Harmonisation Code 1 = The most prevalent classification. Harmonisation Code 2 = The most severe classification.
National Inventory Status
National Inventory Status
Australia - AIIC / AustraliaNon-Industrial Use
Yes
Canada - DSL Yes
Canada - NDSL Yes
China - IECSC Yes
Europe - EINEC / ELINCS /NLP
Yes
Japan - ENCS Yes
S.REACH.GB.ENSafety Data Sheet (Conforms to Annex II of REACH (1907/2006) - Regulation 2020/878)Chemwatch: 9-636846Issue Date: 13/12/2021Print Date: 04/06/2022
Lancaster Way Business ParkEly, Cambridgeshire, CB6 3NX, UK.
+44 (0) 1353 [email protected]
Product code: P04039 Version No: 3.3 Page 16 of 18
National Inventory Status
Korea - KECI Yes
New Zealand - NZIoC Yes
Philippines - PICCS Yes
USA - TSCA Yes
Taiwan - TCSI Yes
Mexico - INSQ Yes
Vietnam - NCI Yes
Russia - FBEPH No (D-glucose)
Legend:Yes = All CAS declared ingredients are on the inventoryNo = One or more of the CAS listed ingredients are not on the inventory. These ingredients may be exempt or will requireregistration.
SECTION 16 Other information
Revision Date 13/12/2021
Initial Date 28/02/2019
Full text Risk and Hazard codes
H320 Causes eye irritation.
SDS Version Summary
Version Date of Update Sections Updated
2.3 13/12/2021 Classification
Other information
Classification of the preparation and its individual components has drawn on official and authoritative sources as well as independent review by the Chemwatch
Classification committee using available literature references.
The SDS is a Hazard Communication tool and should be used to assist in the Risk Assessment. Many factors determine whether the reported Hazards are Risks
in the workplace or other settings. Risks may be determined by reference to Exposures Scenarios. Scale of use, frequency of use and current or available
engineering controls must be considered.
For detailed advice on Personal Protective Equipment, refer to the following EU CEN Standards:
EN 166 Personal eye-protection
EN 340 Protective clothing
EN 374 Protective gloves against chemicals and micro-organisms
EN 13832 Footwear protecting against chemicals
EN 133 Respiratory protective devices
Definitions and abbreviations
PC-TWA: Permissible Concentration-Time Weighted Average
PC-STEL: Permissible Concentration-Short Term Exposure Limit
IARC: International Agency for Research on Cancer
S.REACH.GB.ENSafety Data Sheet (Conforms to Annex II of REACH (1907/2006) - Regulation 2020/878)Chemwatch: 9-636846Issue Date: 13/12/2021Print Date: 04/06/2022
Lancaster Way Business ParkEly, Cambridgeshire, CB6 3NX, UK.
+44 (0) 1353 [email protected]
Product code: P04039 Version No: 3.3 Page 17 of 18
ACGIH: American Conference of Governmental Industrial Hygienists
STEL: Short Term Exposure Limit
TEEL: Temporary Emergency Exposure Limit。
IDLH: Immediately Dangerous to Life or Health Concentrations
ES: Exposure Standard
OSF: Odour Safety Factor
NOAEL :No Observed Adverse Effect Level
LOAEL: Lowest Observed Adverse Effect Level
TLV: Threshold Limit Value
LOD: Limit Of Detection
OTV: Odour Threshold Value
BCF: BioConcentration Factors
BEI: Biological Exposure Index
AIIC: Australian Inventory of Industrial Chemicals
DSL: Domestic Substances List
NDSL: Non-Domestic Substances List
IECSC: Inventory of Existing Chemical Substance in China
EINECS: European INventory of Existing Commercial chemical Substances
ELINCS: European List of Notified Chemical Substances
NLP: No-Longer Polymers
ENCS: Existing and New Chemical Substances Inventory
KECI: Korea Existing Chemicals Inventory
NZIoC: New Zealand Inventory of Chemicals
PICCS: Philippine Inventory of Chemicals and Chemical Substances
TSCA: Toxic Substances Control Act
TCSI: Taiwan Chemical Substance Inventory
INSQ: Inventario Nacional de Sustancias Químicas
NCI: National Chemical Inventory
FBEPH: Russian Register of Potentially Hazardous Chemical and Biological Substances
Powered by AuthorITe, from Chemwatch.
S.REACH.GB.ENSafety Data Sheet (Conforms to Annex II of REACH (1907/2006) - Regulation 2020/878)Chemwatch: 9-636846Issue Date: 13/12/2021Print Date: 04/06/2022
Lancaster Way Business ParkEly, Cambridgeshire, CB6 3NX, UK.
+44 (0) 1353 [email protected]
Product code: P04039 Version No: 3.3 Page 18 of 18